Tender For Construction Of New Bus Shelter With Electrical Arrangements At Thozhicode Pottety Vizhunthayambalam Road Near Rice Mill Junction In Palloor Village Panchayat Of Killiyoor Panchayat Union
Tender Value
4 Lakhs
Estimated cost
Bid Submission
06 Nov 2026
14 days left
EMD
4000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kanniyakumari → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of New Bus Shelter With Electrical Arrangements At Thozhicode Pottety Vizhunthayambalam Road Near Rice Mill Junction In Palloor Village Panchayat Of Killiyoor Panchayat Union
BOQ
| Sl. No. | Item Description |
| 1 | Construction of New Bus Shelter with Electrical Arrangements at Thozhicode pottety vizhunthayambalam Road near Rice mill junction in Palloor village panchayat of Killiyoor panchayat union |
| 2 | Earth work excavation for foundation in all soils and subsoils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and bailing out water wherever necessary and refilling the sides of foundation with excavated earth in layersw of not more than 15cm thick well rammed and consolidated and depositing the surplus earth in all places shown by departmental officers with initial leae and lift etc, complete complying with standard specifiacfion and as directed. |
| 3 | Supply and filling the basement with excavated earth including cost and conveyance and all labour charges etc |
| 4 | Cement concrete 1 : 4 : 8 mix using 40mm HBG metal for foundation inmcluding watering wherever necessary and laid in layers of not more than 15cm thick., compacting etc., complete complying with standard specifications and as directed. |
| 5 | Cement concrete 1:3:6 mix 1 Cement ,3M. Sand (conform to Table I IS 2116-1980) using 20 mm HBGS metal inculding cost and coveyance of all materials to site including labour for mixing , laying,curing etc., complete. |
| 6 | Brick work with cement mortar 1:5 mix 1 Cement ,5M. Sand (conform to Table I IS 2116-1980) using country bricks of size 8 3/4\\"x4 1/4\\"x2 3/4\\" for foundation and basement and superstructure including cost and conveyance of all materials curing etc., complete. |
| 7 | Below GL :Supplying and fabrication,placing in position of mild steel or ribbed Tor steel grills for RCC works including cost of steel and binding wire etc., complete. |
| 8 | Above GL :Supplying and fabrication,placing in position of mild steel or ribbed Tor steel grills for RCC works including cost of steel and binding wire etc., complete. |
| 9 | Supplying fabricating and placing in position mild steel or ribbed for steel for all reinforced centre concrete works as per the design given including cost of steel and binding wire in all floors etc, complete complying with standard specification. The binding wire shall be supplyed by the contractor. |
| 10 | R.C.C 1:11/2:3 using 20mm metal 1 Cement ,1.5 M. Sand (conform to Table I IS 2116-1980) for all RCC works including curing and providing fixtures like fan clamps in the RCC roof wherever necessary and bearing curfaces of walls sides and bottom at slabs etc. as directed by the departmental officers complete |
| 11 | Plastering with Cement Mortar 1:5 mix 12 mm thick 1 Cement ,5E.Sand ( Conform to Table I of IS 1542-1992) including cost and conveyance of all materials to site and labour charges for curing etc., complete. |
| 12 | Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 13 | Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceilingincluding finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work |
| 14 | painting two coat with plastic emulsion in all exposed faces approved variety of cloour pigments including cost of all materials burshed and scaffolding charges etc complete complying with standard specification. |
| 15 | Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone M.Sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. |
| 16 | Plain Cement Concrete 1:2:4 (one cement, two M.Sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers. |
| 17 | Provision for Electrical Arrangement |
| 18 | Light Point SD 26 |
| 19 | Bulk head LED Bulb SD 83 |
| 20 | Fan SD110 |
| 21 | Main Switch 16 Amps (M-1363) |
| 22 | 16Amps Fuse carrier (M-1391) |
| 23 | GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column \\"BB\\" for all works in this package} Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysNov 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender