Tender For Restoration Of Rain Damages To Lwss Rajhana In G.P Rajhana Tehsil And Distt. Shimla. Hp.(Sh:- Repair Of Tank And Repair Of Rising Main Etc. ) Under Pdna.2023. Job No.I
Tender Value
18.70 Lakhs
Estimated cost
Bid Submission
30 Oct 2026
7 days left
EMD
37450
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Shimla → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Restoration Of Rain Damages To Lwss Rajhana In G.P Rajhana Tehsil And Distt. Shimla. Hp.(Sh:- Repair Of Tank And Repair Of Rising Main Etc. ) Under Pdna.2023. Job No.I
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in drains and channels etc. in earth work for pipes upto all depth in all classification of earth work such as pick work, jumper work, saturated soil i/c balling or pumping out water , blasting soft /hard rock or chiseling soft/ hard rock where blasting is prohibited in all lifts including jungle clearance wherever required, trimming and dressing of sides, levelling of beds to correct grade including shoring /struting, planking, timbering and dewatering wherever required stacking the useable /unusable material/soil seperately and after laying,jointing and testing of pipes ,returning the useable soil in treches in 15 cm layers including consolidating of such deposited layer by ramming and watering and then disposing of all surplus excavated soil/ unusable material as directed within all leads and lifts including restoration of un-metalled surfaces to its original condition and including cost of diversion for traffic, night signals, fixing caution boards,crossing over trenches for access to houses, fencing etc. complete in all respect whithin all leads and lifts as per direction of the Engineer-in-charge. |
| 2 | Providing and laying cement concrete work 1:1:2(1cement:1 and:2 graded stone agg. 20mm nominal size) and curing complete excluding cost of form work and reinforcement in reinforced concrete work i/c all leads and lifts complete in all respect. |
| 3 | Foundation and plinth. |
| 4 | 15mm cement plaster in single coat on fair side on brick/concrete/stone walls for interior plastering upto floor two level including arrises, internal rounding angles, chambers and or rounded angles not exceeding 80mm in girth and finished even and smooth:- Cement mortor 1:4 |
| 5 | Prov. in RCC work smooth finishing of the exposed surfaces with cement mortar 1:3(1cement:3sand). |
| 6 | Finishing wall with water proofing cement paint or approved brand and manufacture as and of required shade on undecorated wall surfaces two coats to give an even shade after thoroughly brushing the surface to remove dirt and dust of remaining work. |
| 7 | Providing and laying with butt welding and testing of following dia Heavy Grade GI pipe including jointing the pipes with butt welding at both the end according to relevant BIS standards/approved specifications including manufacturing reducers/tapers, all short pieces and bends as per site requirement and made from parent tubes ( to be measiured and paid alongwith pipes, bends shall be manufactured in such a way that not more than 111/4 degree deflection is caused by a single cut and internal dia is not reduced including hydraulic testing to the entire satisfaction of the Engineer-in-charge. The damaged portion of galvanisation due welding shall be provided with anticorrosive treatment by providing two coats of bituminous paint over priming coat as per AWWA specification C-203-1978.(Earth work to be measured and paid for separately). |
| 8 | 80 mm dia (Heavy) |
| 9 | Providing and laying with butt welding and testing of following dia Medium Grade GI pipe including jointing the pipes with butt welding at both the end according to relevant BIS standards/approved specifications including manufacturing reducers/tapers, all short pieces and bends as per site requirement and made from parent tubes ( to be measiured and paid alongwith pipes, bends shall be manufactured in such a way that not more than 111/4 degree deflection is caused by a single cut and internal dia is not reduced including hydraulic testing to the entire satisfaction of the Engineer-in-charge. The damaged portion of galvanisation due welding shall be provided with anticorrosive treatment by providing two coats of bituminous paint over priming coat as per AWWA specification C-203-1978.(Earth work to be measured and paid for separately). |
| 10 | 80 mm dia (Medium) |
| 11 | Providing fixing and jointing of M.S.flanges conforming to IS-6392-1971 (latest with upto date ammendment) flange dia, table and nominal pressure as specified below welded at both ends of pipes (as per site condition for particular reach as required) according to relevant BIS Code 816-1962 and provided with nuts and bolts of required size as per BIS code 1364 including 3mm thick compressed asbestos fiber gasket of synthetic rubber gasket conforming to relevant BIS code 2712-1965 complete in all respect including all leads and lifts. |
| 12 | Table-28 - 80 mm dia |
| 13 | Table-5 - 80 mm dia Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysOct 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender