Tender For Special Repairs Of Roads At Various Locations In Armd Regt At Jaisalmer Mil Stn Under Ge (A) Jaisalmer
Tender Value
63.98 Lakhs
Estimated cost
Bid Submission
18 Nov 2026
8 days left
EMD
1.21 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaisalmer → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs Of Roads At Various Locations In Armd Regt At Jaisalmer Mil Stn Under Ge (A) Jaisalmer
BOQ
| Sl. No. | Item Description |
| 1 | Repair to Pot holes of any depth, not exc. 1 Sq m each including, sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths etc, cutting aound edges at least 25 mm in depth and making good by filling screened and graded road metal, watering and well ramming (including supply of road metal), etc complete all as specified and as directed by Engr-in-Charge. |
| 2 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400 sqm exceeding 50mm and not exceeding 100mm deep complete all as specified and as directed by Engr - in - Charge. |
| 3 | M & L for applying evenly a prime coat of Cationic Bitumen Emulsion SS1 confirming to IS: 8887 at a rate o application of 0. 7-1 kg/sqm on surface WMM/WBM as specified in Table 500-3 of MoRTH specification for road and bridge works 2013, using mechanical sprayer complete all as specified and directed . |
| 4 | M & L for premixed bituminous macadam laid, rolled and compacted to required gradient and camber (consolidated thickness 75 mm or less), by using 4% bitumen content any penetration using paving bitumen of grade VG-30 confirming to IS-73-2006) etc complete all as specified and as directed by Engr - in- Charge. |
| 5 | Preparing existing black top surfaces by brushing with steel wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt, etc complete all as specified and as directed by Engr - in - Charge. |
| 6 | M & L for applying evenly a tack coat of Cationic Bitumen Emulsion (RS-1) conforming to IS: 8887 at a rate of application of 0.25 kg/sqm on bituminous surface as specified in Table 500-5 of MaRTH specification for road and bridge works 2013, using mechanical sprayer after cleaning of existing surface as specified and directed. |
| 7 | M & L for bituminous premix semi dense asphaltic concrete (SDAC), 30 mm thick (consilidated average thickness) in single layer using paving bitumen of grade VG-30 with 5.5% binder content, mixed in hot mix plant using design mix and laid by mechanical paver and rolled and compacted with using 8 to 10 tonne cap vibratory power road roller to achive the required compactness, camber and gradient finished complete including (cutting of edges of roads straight and site clearance) etc all as specified and as directed by Engr - in- Charge. |
| 8 | S&F in repairs cat eye reflective type of metal body alloy of size 100mmx100mmx20mm with PAMA striplens reflector of model No DA 972.0 fixed with and incl MS Stud of size as per manufactures instructions etc complete all as specified and directed. |
| 9 | S&F in repair, metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1, complete all as specified and directed. |
| 10 | M & L for providing and laying at or near ground level factory made of size 300x300x100MM Premium quality , Jaisalmer stone kerb stone made in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required including dismantling of stone slab complete all as specified. |
| 11 | Demolition of plain cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) Including removal of debries out side MoD land complete all specified and as directed |
| 12 | M&L for cement concrete 1:4:8, type D-2, using 40 mm graded stone aggregate, as in Sub base for floor complete all as specified and directed by Engr-in-Charge.. |
| 13 | M&L for rubber moulded Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratorymethod using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.Note: colour and design as approved by GE |
| 14 | M&L for cement concrete in of type B1, 1:2:4 ( 20mm graded stone aggregate) as in lintels upto 1.5m clearspan, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directedcomplete all as specified and as directed. |
| 15 | M & L for marking 2 mm thick center in stop line, dashes, arrows, brackets and similar work on road surfaces and like n. exc 15cm wide as per IRC pattern with thermo plastic paint of approved make and mix with 8% mica sign applicator machine, complete with traffic diversion arrangement. For example : Painting work on Zebra crossings, speed brakers etc. |
| 16 | S & F in repair 750mm dia convex mirror mounted on metal sheet body and frame work suitable for road side mounted on angle iron 50x50x6mm for mirror botton each 1.20m high above GL and fixed with PCC 1:3:6 type C2 including demolition and including preparation of new steel surfaces and applying two coat synthetic enamel paint over acoat of red oxide complete all as specified. |
| 17 | Dismantling of road sign boards at any shape, type, size, sections incl taking out embedded portion in PCC/ natural ground and making good complete all as specified |
| 18 | M & L cement concrete (1:3:6) type C-1 using 20mm graded stone aggt as in foundaton, filling, mass concrete and sub floors etc. complete all as specified. |
| 19 | S & Fixed stainless steel tube of 50mm dia (Grade-304) and thickness 3.65mm including welding, jointing complete all as specified and directed by Engr-in-Charge. |
| 20 | S & Fixed stainless steel tube of 40mm dia (Grade-304)and thickness 3.25mm including welding, jointing complete all as specified and directed by Engr-in-Charge. |
| 21 | S & Fixed in rpair 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame . The letters approximately covering upto 50% area of the board complete all as specified and directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender