Tender For Provision Of Barber Shop At Installation Kardip, Kamorta. 8847/E8
Tender Value
19 Lakhs
Estimated cost
Bid Submission
09 Nov 2026
9 days left
EMD
38000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
nicobar → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Provision Of Barber Shop At Installation Kardip, Kamorta. 8847/E8
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil, complete all as specified and as directed. |
| 2 | M&L PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete |
| 3 | Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete all as specified and as directed. |
| 4 | Use and waste of formwork to sides of pillars, post, struts, piers, coloumn and stanchions, square, rectangular or polygonal, fair finished surfaces of concrete all as specified and as directed. |
| 5 | Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams to rough finished surface of concrete for flat complete all as specified and as directed. |
| 6 | Use and waste of Formwork to chullah hoods, chajjas, troughs and similar items including edges, rough finshed surfaces of concrete (Horizontal or sloping) complete all as specified and as directed. |
| 7 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, and similar work, not exceeding 200 mm thick etc, fair finshed surfaces of concrete (Horizontal or sloping) complete all as specified and as directed. |
| 8 | Material and Labour for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ,for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 9 | M&L mild steel TMT bars 5mm dia and over up to 10mm for stirrups cut to length , bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia bars confirming to Fe-410-S or Fe-410-0 complete in all respect as specified and directed. |
| 10 | Material and labour for reinforced cement concrete M-30 design mix using 20 mm graded stone aggregate as in foundations including raft, footings , plinth beam, bases for columns, basement slabs and mass concrete and similar work complete all as specified and as directed.Note : Reinforcement and form work shall be measured and paid separately. |
| 11 | Material and labour for Reinforced cement concrete M-30 design mix using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc all as specified and as directed.Note : Reinforcement and form work shall be measured and paid separately. |
| 12 | Material and labour for reinforced cement concrete M-30 design mix using 20 mm graded stone aggregate as in as in beams, cantilever, bressummers, lintels over 1.5M span etc complete all as specified and as directed. Note : Reinforcement and form work shall be measured and paid separately. |
| 13 | Material and labour for reinforced cement concrete M-30 design mix using 20 mm graded stone aggregate as in chajjas etc complete all as specified and as directed. Note : Reinforcement and form work shall be measured and paid separately. |
| 14 | Material and labour for reinforced cement concrete design mix M-30 using 20 mm graded granite stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note : Reinforcement and form work shall be measured and paid separately. |
| 15 | M&L for Pre-cast cement concrete block masonry with solid blocks using type C1(1:3:6) (20mm graded aggregate) ,size exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 16 | Material and labour for 15 mm thick rendering on brick/concrete surfaces in two layers in CM 1:4, finishing coat of 5mm thick, finished even and smooth without using extra cement complete all as specified and as directed. |
| 17 | Material and labour for rendering 15mm thick in Cement Mortar 1:6 on fair faces of brick walls or on concrete surfaces, finished even and smooth,without using extra cement complete all as specified and directed. |
| 18 | Material and Labour for rendering 5 mm thick in cement mortar 1: 3 on fair faces of concrete surfaces of ceiling finished even and smooth with out using extra cement, complete all as specified. |
| 19 | Material and Labour for 75mm thick Plain Cement Concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection, floors, pavings and hardstanding etc, finished even smooth without using extra cement etc including necessary forwork, complete all as specified and as directed. |
| 20 | M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ,light shade, incl 15 mm thick rendering in CM (1:6) complete all as specified and directed. |
| 21 | M&L for digital design glazed ceramic coloured tiles in vertical surface of size of each tile 300 x 450 mm /350x250 mm and 7 to 8 mm thick fixed to set and joint in neat cement slurry and pointed in white or coloured cement to match the same complete all as specified and directed. |
| 22 | Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed. |
| 23 | Removing excavated material (soil) n exc 50 m and depositing where as directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed. |
| 24 | Supply and fixing vitreous China wash hand basin, white (flat back or angle back type or counter top) of size 550X400mm including 32mm brass chromium plated waste fitting, a pair of cast iron bracket duly painted including cutting and pinning in ends making good disturbed surfaces in CM 1:3 excluding pillar tap but chain , plug and porcelain stopper, brackets etc all as specified and as directed.MAKE : Hindware , Jaquar |
| 25 | Supply and fix fancy type 15mm dia pillar tap, cast copper alloy, chromium plated, with capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw for iron pipe Make: CERA /Parryware/Hindware |
| 26 | Supply and Fixing stop valves/angle cock, 15mm bore, fancy type, with long shank & cut concealed type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.MAKE : Hindware , Jaquar |
| 27 | Supply and fix waste coupling of PTMT 32 mm size (half or full threaded) suitable for urinals/ WHB/Sink etc (Minimum weight 32 mm - 45 gms) all as specified and as directed. |
| 28 | Supply and fixing Towel rails tubular brass chromium plated 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed. |
| 29 | Supply and fixing galvanised steel water tubing medium grade 15 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc, fixed to wall/floor/ceiling including necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed. |
| 30 | Supply and fixing galvanised steel water tubing medium grade 20 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc, fixed to wall/floor/ceiling including necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed. |
| 31 | S&F PVC (SWR) pipes 75 mm dia. single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 32 | S&F PVC (SWR) bend 75 mm dia with access door complete all as specified and as directed. |
| 33 | Material and labour for preparation of of new plastered/concrete surfaces of walls and applying two coats of distemper oil-emulsion of approved shade/tint over a coat of primer, over surface of wall all as specified and as directed. |
| 34 | Material and labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 35 | Supply and fix Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed.Note : Glass panel/particle board panel filling shall be measured and paid separately. |
| 36 | Supply and fix powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, and sliding tower bolt 150mm long anodised aluminium snap beading, screws etc. complete all as specified and as directed. |
| 37 | Supply and fix for powder coated, Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified. |
| 38 | S&F aluminium (Die cast body) Door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters 701 to 850mm in width and of weight between 36 ro 60 Kg complete all as specified and as directed |
| 39 | Supply and Fixing 4mm thick ordinary quality glass with film cover, ordinary quality and glazing with oil and putty in square not exc 0.5 sqm in each pane complete all as specified and as directed. |
| 40 | Supply and fix rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats conforming to Fe-410W(Gde E-250) quality A complete all as specified and as directed. |
| 41 | S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. |
| 42 | S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. |
| 43 | M&L for MS work as in Wind Tie in roof and MS structural works in trusses, etc with screwed ends including nuts, washers and mild steel plates for walls chimneys, roofs arches etc any kind rods and straining bolts conforming to Fe-290 Gde-165 complete all as specified . |
| 44 | M&L for preparation of new or previously untreated steel surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and as directed |
| 45 | Material and Labour for pre-laminated particle board 18/19 mm thick, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws in timber frame work complete all as specified and directed. |
| 46 | Supply & fixing of 30mm width flap (when open) Continuous (piano) hinges, stainless steel all as specified and as directed. |
| 47 | Supply and fix extruded brass handles fabricated type polished of size 100mm complete all as specified and as directed. |
| 48 | Supply and fix anodised aluminium snap grid frame work for false ceiling with 605mm x 605mm size, consisting of main Tee of size 40 x 40 x 2mm, cross Tee of size 40 x 40 x 2mm and wall angle of size 40 x 40 x 2mm of approved make including all necessary cuttings, fixing of aluminium section firmly in position with and including steel hangers 6 mm dia G.I. wire (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 40 mm long in soffit of slab/walls complete all as specifed and as directed including provision of with 4mm thick Non Asbestos boards, ordinary type for fixing in 600 mm x 600mm grid, fixed in ceiling, flat or sloping, complete all as specified and directed.Note :- Rate quoted above shall be deemed to include for making holes, cutting chassis if any required and making good to existing walls in cement mortar 1: 3 to match with existing surface finish as directed at site. |
| 49 | Material and Labour for Granite 20mm thick ( of any type table rubbed and polished) work machine cut as in steps, jambs pillars,window cills, cooking platforms and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of granite and laid over and including 15mm thick cement mortar 1 :4 complete all as specified and directed. |
| 50 | Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed. |
| 51 | Removing excavated material (soil) at adistance exc 50 m and n exc 100 m and depositing where as directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed. |
| 52 | Material and labour for hard core of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread, and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface all as specified and as directed. |
| 53 | Material and labour for 100mm thick plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floors including necessary form work all as specified and as directed. |
| 54 | Material and labour for chequered cement concrete tiles 30cm x 30cm x 25mm with grey cement and pigment, hydraulically machine pressed, set, jointed and pointed in neat cement slurry to match colour of tiles, over and including 15mm thick screed in CM 1:6 in floors complete all as specified and as directed. |
| 55 | Material and labour for Plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in copings, kneelers, apex stones,bed plates, kerbs, bed block for hold fast including necessary form work all as specified and as directed. |
| 56 | M&L point wiring complete with 1.5 Sqm sincle core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI) marked concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with 3mm thick bakelite/PVC sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc, all as specified and as directed for the following :- |
| 57 | (a)One light point controlled by one switch |
| 58 | (b)One exhaust fan/ fan point controlled by one switch |
| 59 | (c) One 3 pin socket outlet 5 Amps on same board |
| 60 | (d) one 3 pin socket outlet 5 Amps point controlled by one switch on Independent board. Please Enable Macros to View BoQ information |
| 61 | (d) one 3 pin socket outlet 5 Amps point controlled by one switch on Independent board. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender