Tender For Establishment Of 20 Mt Capacity Spawn Production Laboratory Under Hadp Project No. P-10 Promotion Of Mushroom Cultivation At Gole Pully Talab Tillo, Jammu
Tender Value
1.49 Crore
Estimated cost
Bid Submission
27 Oct 2026
0 days left
EMD
3 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Establishment Of 20 Mt Capacity Spawn Production Laboratory Under Hadp Project No. P-10 Promotion Of Mushroom Cultivation At Gole Pully Talab Tillo, Jammu
BOQ
| Sl. No. | Item Description |
| 1 | Clearing of site by employing labour, tool and tackle, men and machinery for start of work. The job includes labour cost, hire charges of tools and tackles, machinery and taxes as applicable |
| 2 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed Foundation for plinth workFoundation for columns PaverStairs Total = 44.05 m3 |
| 3 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)Foundation for plinth workFoundation for columns PaverStairs Volume FlooringTotal = 44.44 m3 |
| 4 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. 1:2:4 (one cement: Two coarse sand: Four Graded stone aggregate 20 mm nominal in size) Foundation for plinth workFoundation for columns PaverStairsVolume FlooringTotal = 76.01 m3 |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columnsPlinth above NSL Total=94.80 m2 |
| 6 | Providing and laying river bed material / good earth including loading unloading and watering after every layer of 30 cm. The rolling is to be done by hand rammer. The rate includes supply and carriages and all forms of taxes.Volume Flooring Total = 132.67 m3 |
| 7 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc.complete. 50 mm thick 20 mm size stone aggregate.Area FlooringTotal = 327.18 m2 |
| 8 | DSteel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.Columns a. 10 mm rebars for column mesh Flooring(300 mm c/c)a. 10 mm rebars Tie beama. 10 mm rebars b. 8 mm stirrups ( 300 mm c/c) Total = 1839.34 kgs |
| 9 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all completeA. SHEDColumns(80 x 80 x 4 mm) M.S. Plates 300x300x6 mm 300x300x10 mm M.S. Anchor Bolts with nuts(20 mm x 750 mm) Truss/Rafters/purlinsOuter members of truss including king post (80x40x4 mm) Inner members of truss (60x40x3 mm) Purlins(60x40x2.5 mm) Side rails (50x25x2.5 mm) Columns(60 x 40 x 3 mm) Total Weight = 5471.98 kgs |
| 10 | Providing and fitting of 0.50 mm pre profiled colour coated corrugated sheets to be laid over a frame work of trusses columns and purlins using hot dipped Zinc Coated self-drilling screws, Hexagonal Washers, Fasteners etc.Total = 417.16 m2 |
| 11 | Providing and fixing ACP Sheet of thickness not less than 3mm over frame with the help of screws and other accessories required for completion of job.job includes material cost,labour cost and taxesArea= 1147.50ft2 |
| 12 | Providing and fixing/ installation of Rain water gutter system(min. 6 inches) along the two sloping sides of shed with all required accessories like support bracket, elbows, guards, stop ends, gutter jail, rain water gutter pipes, gutter downspout, gutter adapter etc., fittings and all allied works. The complete job including cost of material, labour, carriage, tools and tackles and taxes.Total length = 91.46 metre |
| 13 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & patternTotal = 142.21 m2 |
| 14 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. 1:2:4 (one cement: Two coarse sand: Four Graded stone aggregate 20 mm nominal in size) Locking of EdgesVolume FlooringTotal=1.20 m3 |
| 15 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work(steel).Job includes material cost,labour cost and taxes. |
| 16 | Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid on 20mm thick cement concrete in 1:4 (1 cement:4 coarse sand) including grouting of joints with white cement and matching pigments etc. complete size of tiles 600mm X 600mm including all leads ,lifts and carriage complete.Floor area= 200.00 m2 |
| 17 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)A. WASHROOM Total = 66.92m2 |
| 18 | Wall TILESProviding and fixing Ist quality c wall tiles conforming to IS : 15622(thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade completeA. WASHROOM Total = 66.92m2 |
| 19 | 12mm Cement plaster of mix:1 : 4( 1 cement : 4 fine sandTotal= 45.54 m2 |
| 20 | Electrical fitting by way of Providing and fitting of 10 no. ceiling fans of sweep 1200 mm, 04 no. exhaust fan heavy duty 18”dia with lovers, 40 nos. 12 W Led light, 15 Nos. 100W and 05 Nos 50 W LED Flood Lights and with 08 Nos. poles of suitable height and shape grouted properly in ground with cement concrete mixture for flood lights, 5/6A&15/16A sockets with switches as per requirement including wiring of all points in PVC batten/conduit. Job also includes Providing and laying of 1 sqm/1.5 sqm/2sqm/2.5sqm/4sqm as per site requirement from supply point to electrical points to all the rooms. It also includes providing and laying/fixing of wire/cables of sizes and length, pvc conduits, MCB/MCCB, distribution box, extension board (if required) and other allied items all as per site requirement. The complete job includes material cost tool and tackles, labour cost and taxes. |
| 21 | Providing and fixing false ceiling with 12 mm thick plain/ semi perforated or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to IS:3087, finished with a coat of aluminum primer on both sides & edges, including two coats of synthetic enamel paint of approved quality on exposed face, fixed to a grid made out of anodized aluminum (with 15 micron anodic coating) T- sections35 x15x1.5 mm size main runners, cross runners 23.5x19x1.5 mm fixed to main runners placed 600 mm centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia. M.S rod fixed to roof slab by means of ceiling cleats and dash fastener. The suspenders shall be placed 600 x 1200 mm centre to centre including fixing to the frame with C.P brass screws and applying a priming coat of primer and paint as per Direction of Engineer Incharge .Roof area = 200 m2 |
| 22 | Providing and fitting of following sanitary items in two nos bathrooms and make them fully functional: 02 nos. water closet / flushing toilet( 02 western) with all accessories, 01 no urinal pot with all accessories, 02 nos wash basin of size not less than 18” with all accessories and outlet pipe 03 nos looking mirrors of appropriate size, Towel rods 02 nos., 02 nos Soap holder, P/F of Bibcocks and all other accessories. Providing and laying of 150 mm PVC pipe of reputed make for sewage from bathroom to soakage pit and 75 mm PVC pipe for urinal and wash basin. Providing and laying of CPVC pipe of size 1”and1/2” inch for water supply system to all the bathrooms from source to the bathroom along with all allied fitting and accessories. Job also includes laying of CPVC supply line and PVC drain pipes from incubation room, inoculation room, media room and boiler room as per the site requirement. It also includes construction of main holes and soaking pit as per site requirement, cover at the top of the main/check hole, soaking pit, fitting of gas pipe along with connections with the bathroom to make bathroom fully functional with all other allied accessories. The job also includes P/F of 2000 Ltr P.V.C water tank with MS Pipe stand made out of pipe 60x40x4mm and height(not less than 15’) for providing sufficient head for discharge of water from tank to washrooms and along all allied accessories, fittings and connections, 0.5 hp mono block pump with required pipes, accessories for connections with the pvc tank and underground storage tank. The complete job including cost of material, labour, carriage, tools and tackles and taxes. |
| 23 | Supply, Installation, Testing and Commissioning of ABC type fire extinguisher of 6 kgs capacity with MS body, discharge hose, wall mounting bracket with fasteners and suitable signage. The complete job including cost of material, labour, tools and tackles and taxes. |
| 24 | Supply, Installation, testing, commissioning of Modular type Double Skin Clean Room Wall PCGI(Powder coated) puf panels 80 mm thick, made of 0.6 mm thick Galvanized Iron sheet as per IS 277 with 60–70-micron thick powder coating, in-filled with PUF. The density of it is 38-40 Kg. /m³; with all required accessories like C Type Floor Track, Top Channels, male female channel etc. to hide any MS structure and giving clean finish from inside, Internal/External flashing to be provided on. Prefabricated Sandwich PUF panels with Cam toggle type fasteners fitted and self-locking PVC gaskets fitted on all sides of wall including rivets, flashing, Silicones, Anchor fastener, self drilling screw and all other allied accessories required for the installation/erection of PUF panels. |
| 25 | Supply, Installation, testing, commissioning of Modular type Double Skin Clean Room Wall PCGI (Powder Coated) puf panels 60 mm thick, made of 0.6 mm thick Galvanized Iron sheet as per IS 277 with 60–70-micron thick powder coating, in-filled with PUF. The density of it is 38-40 Kg. /m³; with all required accessories like C Type Floor Track, Top Channels, male female channel etc. to hide any MS structure and giving clean finish from inside, Internal/External flashing to be provided on. Prefabricated Sandwich PUF panels with Cam toggle type fasteners fitted and self-locking PVC gaskets fitted on all sides of wall including rivets, flashing, Silicones, Anchor fastener, self drilling screw and all other allied accessories required for the installation/erection of PUF panels. |
| 26 | Supply, Installation, testing, commissioning of Modular type Double Skin Clean Room Wall PCGI puf panels 50 mm thick, made of 0.6 mm thick Galvanized Iron sheet as per IS 277 with 60–70-micron thick powder coating, infilled with PUF. The density of it is 38-40 Kg. /m³; with all required accessories like T grid, suspension rod, nut bolt etc. to hide any MS structure and giving clean finish from inside,. Internal/External flashing to be provided on. Prefabricated Sandwich PUF panels with Cam toggle type fasteners fitted and self-locking PVC gaskets fitted on all sides of wall including rivets, flashing, Silicones, Anchor fastener, self drilling screw and all other allied accessories required for the installation/erection of PUF panels. |
| 27 | Supply, Installation, testing and commissioning of Coving R-75 with 2D and 3D Corners as applicable as per the site requirements to hide any MS structure and giving clean finish from inside. The job includes allied accessories & equipment required for completion of work. The Complete job includes material cost, labour cost, freight charges, tools and tackles, hire charges of machinery and all kinds of taxes thereof. |
| 28 | Providing & fixing of GI return air riser inside of 60 or 80 mm thick wall panels as per the site requirement and design consideration. Return Air riser duct will extend 150 mm above ceiling with a flanged connection to main Duct. Riser will be provided with SS 304 1.2mm thick Perforated Grill. Solid Area should be fitted in wall panel area. |
| 29 | Providing and fixing of Return air risers S.S Grill of size 600 x 300 mm /450x300 mm with 10 micron Filter along with SS perforated screen and Volume Control Damper. The Complete job includes material cost, labour cost, freight charges, tools and tackles, hire charges of machinery and all kinds of taxes thereof. |
| 30 | Supply, Installation, testing, commissioning of Single Leaf clean room door/air lock 900 x 2100 mm, 30min. Fire Rating made up of 1.2 mm thick GI sheet, with PUF as infill material with Polyester Powder Coated finish with Hardware as mentioned below, with vision glass and accessories like SS ball bearing Hinges (101x75x3mm), SS One side D Handle another side Push Plate/ Back to back handle (19*300)mm, Dead lock Both Side Key operation, double Clear Glazed 6mm Glass 400 x 600 mm (Toughened Glass), Door Closer TS 71 STD ARM, Automatic Drop Seal, Door Seal Grooved Type, Door Stopper, SS304 Kick Plate One side (300 mm Height) 0.8 mm thk, Flush Bolt for Double Leaf Door, Panic bar 378, 1 point locking device with external trim. The Complete job includes material cost, labour cost, freight charges, tools and tackles, hire charges of machinery and all kinds of taxes thereof. |
| 31 | Providing and fixing of Aluminium Door of size 900 mm x 2100 mm gauge not more than 12 mm With tinted toughened glass and Partition board including glass, rubber beading, aluminum sheet panels for doors and other allied accessories such as toggles, handles, hinges etc. The color and final design is as approved by Engineer in charge. The Complete job includes material cost, labour cost, freight charges, tools and tackles, hire charges of machinery and all kinds of taxes thereof. |
| 32 | Providing and fitting of Double Glaze Vision panel with thickness not less than 26 mm Clear Toughened glass with 20mm black border with all accessories like double adhesive tape, silicon sealant and silica gel with GI powder coated inner channel (Max. Jamb 80mm) View Panel Size 900*1200mm. The Complete job includes material cost, labour cost, freight charges, tools and tackles, hire charges of machinery and all kinds of taxes thereof. |
| 33 | Providing and fitting of Full Height Aluminium clear toughened Glass Door of size (1809x3000) mm with all accessories including glass, rubber beading, aluminum sheet panels for doors and other allied accessories such as toggles, handles, hinges etc. The color and final design is as approved by Engineer in charge. The Complete job includes material cost, labour cost, freight charges, tools and tackles, hire charges of machinery and all kinds of taxes thereof. |
| 34 | Providing and fitting of SOS Emergency Door (900 × 2100 mm) – 42 mm thick shutter fabricated from 0.8 mm GI sheet with 80 × 55 mm frame made from 1.2 mm GI sheet, fitted with SS 304 (100 × 75 × 3 mm) hinges, double vision panel with 5 mm toughened glass, and heavy-duty panic bar, complete with red powder coated finish. The Complete job includes material cost, labour cost, freight charges, tools and tackles, hire charges of machinery and all kinds of taxes thereof. |
| 35 | Providing and laying of Seamless antistatic (EPOXY) floor – Laying 3mm (2+1) mm thick self-levelling epoxy floor. The existing floor should be properly cleaned up levelled and roughened to prepare the surface for application of epoxy primer, filling of small cracks and unevenness with epoxy repairing putty. Over a uniform cemented flooring 2 mm of hardener (screed compound) is applied after that 1 mm of semi liquid epoxy resin will be applied for smoothening. Epoxy used for this application will be self-levelling and clean room compatible, The floor level shall match with the surrounding area. The color and final design is as approved by Engineer in charge. The Complete job includes material cost, labour cost, freight charges, tools and tackles, hire charges of machinery and all kinds of taxes thereof. |
| 36 | Supply, Installation, testing and commissioning of Ceiling mounted CRCA powder coated terminal HEPA module with HEPA Filter housing, gaskets, 1.2 mm thick Stainless steel perforated sheet and volume control damper. The provision for DOP/ PAO testing port shall be provided. Efficiency: 99.95% down to 0.05 μ, All necessary fixtures to secure the modules in false ceiling shall be part of the scope. The job also includes Supply and installation of HEPA Filter of capacity down to 0.3 micron with 99.97% efficiency. The color and final design is as approved by Engineer in charge. The Complete job includes material cost, labour cost, freight charges, tools and tackles and all kinds of taxes thereof. Size: - 450 x 450 x 305 mm |
| 37 | Supply and installation of SS 304 perforated sheet with 70% perforation capsule cutting in heavy gauge. The Complete job includes material cost, labour cost, freight charges, tools and tackles and all kinds of taxes thereof. |
| 38 | Supply, Installation, testing and commissioning of Site fabricated GSS ducting with zinc coating of 120 GSM total on both sides as per IS 277 complete with MS supports as per site requirements, IS standards. The scope shall include turning vanes, bolts and nuts, gaskets, stiffeners, flanges/Transverse Duct connectors. All Ducting joints shall be sealed with Sealant including Fire Damper and Damper as applicable. Should be in 22-24 gauge respectively. The Complete job includes material cost, labour cost, freight charges, tools and tackles and all kinds of taxes thereof. |
| 39 | Supply, Installation, testing and commissioning of 9 mm thick Closed cell Cross linked Polyethylene Foam (XLPE) Insulation (outdoor purpose) pasted with suitable adhesive. The Complete job includes material cost, labour cost, freight charges, tools and tackles and all kinds of taxes thereof. |
| 40 | Supply, Installation, testing and commissioning of Floor Mounted factory fabricated Double skin Air Handling Unit (re-circulation Type) made out of 0.6mm thick pre- coated GI outer skin and not less than 0.6mm thick Plain GI inner skin with PUF insulated panel (not less than 40kg/m3) with Aluminium profile, comprising of blower section with backward curved fan with IE-2 Motor Vibration isolators, mixing chamber,10 Microns Pre filters (G4) 5 Micron Fine-Filters (F7),4/6 rows deep DX cooling copper coil with Aluminium fins Sandwich insulated Condensate drain pan shall be fabricated from minimum 18G stainless steel sheet (SS 304),AHU shall be mounted on anti- vibration arrangement and PCC foundation. Job includes Supply, Installation, testing and commissioning of Dust and vermin proof indoor type factory-built sheet steel enclosed modular construction floor/ wall mounted control panel for AHU Outdoor unit, suitable for operation on 415±10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with CRCA sheet steel of 2mm thick for framework and covers etc preferably CPRI certified manufacturer. The panel comprising of Incomer MCCB/MCB, Outgoing MCB,, manual operational facility, internal wiring, On Off Indication Lamp, Microprocessor based electrical panel as required. |
| 41 | Supply, Installation, testing and commissioning of top discharge Variable Refrigerant Flow Type Outdoor unit with energy efficient Compressor, Copper condenser with anti- corrosive coating, condenser fan with motor, Filter Dryer, Expansion valve, Y-joint etc complete job includes nitrogen testing and refrigerant gas charging. The system will be suitable for 415V+/- 10%, 3 Phase operation. Capacity: 8.5 TR |
| 42 | Supply & Layout of Copper refrigerant piping seamless tube of different diameters as per the design of OEM (IS: 10773 / ASTM B280 /B88) with proper insulation using 13 mm thick closed cell polyethylene insulation with Aluminium foil between condensing units and AHUs/FCU including cutting, brazing, support and fixture etc. Complete job includes material cost, labour cost, freight charges, tools and tackles and all kinds of taxes thereof. |
| 43 | Supply & Layout of PVC 40 mm pipeline for condensate drainage water piping from the AHU to the nearest drain point. Complete job includes support, fixtures, bends etc. |
| 44 | Design, Providing, installation, testing & commissioning of Floor mounted, outdoor, double door type main panel operating on 415V, 3 PH, 50 Hz for 02 nos. incoming one for main supply and other for emergency from DG Set with the help of change over switch supply system. It should be made out of dust and vermin proof fabricated out of 16 SWG CR sheet and with outdoor canopy suitable for outdoor installations. The panel should be sturdy enough for vibration free operation and should be equipped with suitable locking/ sealing arrangement. The structure should be provided suitable entry and exist holes for incoming and outgoing cables. The panel should be given two coats of antirust primer and two coats of enamel paint. The panels should be equipped with following items:- Incomer1. Incomer-1 : MCCB 200 Ampere 4 pole or of suitable rating which can cater complete load of all the machines/building load etc.2. Incomer 2: Changeover Switch 200 Ampere 4 pole front operated for Emergency line (i.e DG Set) or of suitable rating which can cater complete load of all the machines/building load etc.3. MCCB of suitable rating for servo stabilizer by pass.4. Aluminum 4 Pole Bus Bar – 02 set 5. Digital Voltmeter with Selector Switch 6. Digital Ammeter with Selector Switch & CT’s 7. Phase Indicator Set 8. Single phase, over voltage, under voltage, unbalanced, reversed phase relays.Outgoings1. Suitable number of outgoings as per the design of spawn lab equipments including AHU, Outdoor Unit, Autoclaves , Incubators, lightning load and other electrical equipments installed in Spawn lab. Note: Each Equipment installed shall have separate outgoing of suitable rating. The panel shall design shall be approved by Engineer-in-recharge at site before installation. Complete job is of turnkey basis and includes cost of material, labour charges freight charges and other tools and tackles required for the execution of the job. |
| 45 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc.with charcoal/ coke and salt as required. (MR) |
| 46 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring |
| 47 | Proving and laying of control cum communication wiring 2 core 1.5 sqmm shielded copper cable in PVC Conduit/raceway. |
| 48 | Proving and laying of PVC insulated and PVC sheathed/ XLPE power cable of following sizes with proper clamping and thimbling in PVC Conduit/raceway. 4 core x 95 sqmm Aluminum XLPE armoured cable |
| 49 | Proving and laying of PVC insulated and PVC sheathed/ XLPE power cable of following sizes with proper clamping and thimbling in PVC Conduit/raceway 4 core x 35 sqmm Copper XLPE armoured cable |
| 50 | Proving and laying of PVC insulated and PVC sheathed/ XLPE power cable of following sizes with proper clamping and thimbling in PVC Conduit/raceway 4 core x 25 sqmm Copper XLPE armoured cable. |
| 51 | Proving and laying of PVC insulated and PVC sheathed/ XLPE power cable of following sizes with proper clamping and thimbling in PVC Conduit/raceway 4 core x 16 sqmm copper XLPE armoured cable |
| 52 | Proving and laying of PVC insulated and PVC sheathed/ XLPE power cable of following sizes with proper clamping and thimbling in PVC Conduit/raceway 2 core x 6 sqmm copper XLPE armoured cable |
| 53 | Proving and laying of PVC insulated and PVC sheathed/ XLPE power cable of following sizes with proper clamping and thimbling in PVC Conduit/raceway 2 core x 4 sqmm copper XLPE armoured cable |
| 54 | Supply and laying of perforated hot dipped galvanized Iron cable tray of size 150mm x 50mm depth in convenient sections joint with connectors/ support etc along the wall/ceiling as required on site. |
| 55 | Supplying and fixing of Ceiling mounting flush type square LED (size600mm x 600mm panel) lighting fixture suitable for clean room operation. |
| 56 | Supplying and fixing of Stainless steel Dress cabinet with shoe rack, Dress Cabinet Size: 1200mm x 450mm x 900mm Shoe Cabinet: 900mm x 600mm x 300mm (with 6 shoe boxes compartments) |
| 57 | Laboratory Module750mm with C-Frame complete in all aspects :- Providing and Fixing Complete set C-Frame based Modular Under benches suspended storage Unit of Double door and single drawer with Cam lockSize should be width 750mm x depth 530mm x height 635mm. The whole unit must be fabricated in 0.9mm 120 GSM GPSP/GI sheet metal with adjustable shelf. The whole unit must pure epoxy powder coated with 70-800micron thickness. The must consist of SS/PP hinges, Drawer should be fitted with sliding channels and SS Door handles. 'C\\" Frames should have Depth- 700 x Width-30 mm and Height-780 (Sitting) & Height-890mm (Standing) Vertical Legs depending as per actual site requirements. Connecting Sets member arms should be made GPSP/GI 120GSM in 1.2mm thickness and 5mm end profile connection to C frames. Worktop should be Black Granite17(±1) mm thick with pre molded and polished edges. The overhang of granite should be 30mm–50mm. at front side of under storage cabinets, Neoprene Strip (25mm wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR- 998 glue, As required the cover Panel End side panel for main unit, 600mm Depth, 900mm Height. |
| 58 | Laboratory Leg-Space 750mm with Back Cover Panel as Required Complete Unit: Providing & Fixing with SITC of Leg- SpaceofLength-750 with Back Cover panels. The whole unit should be made from 0.9mm GPSP/GI sheet metal with pure epoxy powder coating 70-80 micron. Work top should be black Granite (Acid/Chemical Resistance)17 (±1) mm thick with high quality granite in jet black colour with pre moulded, pre polished edges. The overhang of granite should be 30 mm – 50mm. at front side of under storage cabinets, Neoprene Strip (25 mm wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR-998 glue. |
| 59 | Laboratory 750mm PP Sink Module with accessories complete: Providing and fixing of 750mm under bench suspended sink storage unit of width 700mm, Depth 530mm, height of unit should be 635mm with two shutters. The whole unit must be pure epoxy powder coated 70-80micron coated 0.9mm metal sheet GPSP, Cabinet shutter must be fitted with SS/PP hinges, SS Door handles of approved make. The Polypropylene Sinks (Drop-in) of overall size 500Length x 398Width x 235Depth (mm) or as per site black color classic timeless appearance in matt finish, non rusting and easy to maintain with bottle trap. Waste Coupling For PP/Ceramic. Anti-Siphon bottle trap, (Black color) Flexible connector to connect sink to the waste line. Brass epoxy coated water faucets for Sink unit shall have 3 way (2 straight+1 swan neck)turn type water faucets. It should be Ph and rust resistant and has detachable hose nozzles. Worktop should be black Granite (Acid/Chemical Resistance)17(±1)mm thick with high quality granite in jet black color with pre-molded, pre-polished edge. The over hang of granite should be 30mm–50mm. at front side of under storage cabinets, Neoprene Strip (25 mm wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR- 998 glue. Complete in all respect as directed and upto the entire satisfaction of Engineer in Charge. |
| 60 | Laboratory 600 mm PP Sink Module with accessories complete Providing and fixing of 600mm under bench suspended sink storage unit of width 600mm, Depth 530mm, height of unit should be 635 mm with two shutters. The whole unit must be pure epoxy powder coated 70-80micron coated 0.9mm metal sheet GPSP, Cabinet shutter must be fitted with SS/PP hinges, SS Door handles of approved make. The Polypropylene Sinks (Drop-in) of overall size 500Length x 398Width x 235Depth (mm) or as per site black color classic timeless appearance in matt finish, non rusting and easy to maintain with bottle trap. Waste Coupling For PP/Ceramic. Anti-Siphon bottle trap, (Black color) Flexible connector to connect sink to the waste line. Brass epoxy coated water faucets for Sink unit shall have 3 way (2 straight+1 swan neck)turn type water faucets. It should be Ph and rust resistant and has detachable hose nozzles. Worktop should be black Granite (Acid/Chemical Resistance)17(±1)mm thick with high quality granite in jet black color with pre-molded, pre-polished edge. The over hang of granite should be 30mm–50mm. at front side of under storage cabinets, Neoprene Strip (25 mm wide & 6 mm thick) backing material for granite should be NEOPRENE fixing with SR- 998 glue. Complete in all respect as directed and upto the entire satisfaction of Engineer in Charge. |
| 61 | Supply, Installation, Testing and Commissioning of BOD Incubator 400 ltr Size: 24\\" × 24\\" × 36\\"Capacity:400LitresShelves:3Nos.Construction: Mild Steel (MS) Powder Coated Exterior with SS Inner ChamberConstruction: MS • PID Digital Temperature Indicator Cum Controller • Insulation: PUFF Insulation • Dual Display Microprocessor • Air Circulation: Dual Fans • Display: Digital • Voltmeter: Digital • Mobility: Castor Wheels Technical Details• Designed for low temperature incubation and routine determination of Bio-Chemical Oxygen Demand (B.O.D.). • For work at lower temperatures, a cooling unit is provided at the lower portion of the working chamber. For work at higher temperatures, a heating arrangement has been provided in the inner chamber. • The temperature varies from 5°C to 60°C, adjustable at any desired point by a Dual Display Microprocessor PID Digital Temperature Indicator Cum Controller with an accuracy of ±0.5°C. • Air circulation fans are provided to keep the temperature uniform inside the chamber. • Inner chamber is made up of stainless steel sheet. • Supplied with three removable perforated shelves. • Exterior is made of thick mild steel, duly finished with powder coating. • Double wall door is provided with magnetic gasket and lock & key arrangement. |
| 62 | Supply, Installation, Testing and Commissioning of Autoclave (Vertical) Size: 22\\" × 30\\" (550 × 750 mm)Capacity: 180 LitresLoad: 6.0 kWConstruction• Inner Chamber: SS 304 • Outer Chamber: SS 304 • Lid: SS 304 (Heavy-duty machined plate) • Support Ring: SS 304 • Leg Stand: SS 304 • Sheet Thickness: Minimum 2 mm • Gasket: Jointless Silicone Rubber Operation• Semi-Automatic Standard Features• Radial locking lid with safety locking mechanism • Vacuum breaker • Water level indicator • Stainless steel perforated basket/carrier • Automatic low water cut-off system • Automatic pressure control switch • PID digital temperature controller with timer Technical Specifications• Inner & outer chamber and support ring are fully made of SS 304. • Heaters cover stand and carrier/bucket are made of SS. • Lid made of thick machined stainless-steel plate. • Radial locking lid ensures user safety and safe locking. • Lid is fitted with pressure gauge, spring loaded safety valve, double safety valve, manual exhaust valve, vacuum breaker as a safety device and water level indicator• Drain valve facilitates easy cleaning of the chamber. • Moulded joint less silicon rubber gasket. • All internal joints are argon arc welded, ground and polished to give crevice free internals. • Miniature circuit breaker for mains on/off plus safety of control panel. • Industrial grade energy efficient heaters reduce power bill drastically.• Operating Pressure from 15 psi to 22 psi.• Electrical Panel of suitable rating and capacity including other allied works. |
| 63 | Supply, Installation, Testing and Commissioning of Autoclave (Horizontal)Autoclave (Horizontal); 01 Nos Double Hinge Door Chamber Size 900 x 900 x 1800 mm Fully Automatic, Electric Load 72 kW Capacity 1458 Ltrs (Net Steel) Size: 36\\" × 36\\" × 72\\" (900 × 900 × 1800 mm)Capacity: 1500 LitresLoad: 54.0 kWConstruction: Fully Automatic Double Door, SS 304Construction• Inner Chamber: SS 316. • Outer Chamber: SS 304. • Door: SS 304. • Jacket, Ring & Boiler: SS 304. • Tubular Stand: Made of SS 304. • Radial Locking System & Arm: Made of SS. • Hinges: Made of SS 304. • Steam Pipeline: Made of SS 304. • Stand: Made of SS 304. • Chamber Thickness: 3 mm. • Jacket Thickness: 3 mm. • Lid Thickness: 12 mm. Operation & Control• PLC Control System (Fully Automatic). • Automatic sterilizing cycle with auto purging. • Water level indicator. • Vacuum breaker. • Automatic pressure cut-off switch. • Automatic low water cut-off switch. • Digital temperature indicator cum controller with timer. • Display: Jumbo LCD (20 × 4). • Control: ON/OFF / T.P. • Inputs: PT-100 sensor for boiler and chamber, pressure sensor for chamber. • Purging range: User settable. • Sterilization time: User settable. • Post sterilization drying time: User settable. • Inlet for HEPA filter. • Boiler control: User settable. • Inbuilt sterilization cycle process. Heating System• Mode of Heating: Electrically heated by flange type heaters. • Power Supply: 440 V, 3 Phase. • Heater Capacity: 18.0 kW. Pressure & Temperature• Working Pressure: Variable from 5 psi to 20 psi. • Recommended Sterilization Pressure: 15 psi to 17 psi. • Working Temperature: 121°C. • Hydro Test Pressure: 40 psi. Door• Double door fitted with radial shooting arm made of SS 304. Safety Features• Safety valve provided against excess pressure in jacket and steam generator. Chamber Condensate Line• Incorporated with Spirax steam traps and check valve for efficient condensate removal and optimum temperature achievement. Steam Generator (Boiler)• Attached underneath the jacket. • Fitted with immersion type industrial heating elements. • Water inlet and outlet valves. • Water level indicator. • Automatic pressure stat switches to control boiler pressure.Note: Job includes Electric panel of suitable capacity with necessary safety features including all other allied works. |
| 64 | Supply, Installation, Testing and Commissioning of Laminar Air Flow Size: (1200 × 600 × 600 mm)Standard Features• Construction: MS. • Body: Heavy-duty MS or corrosion-resistant SS304 body ensures long operational durability. • Air Velocity: 0.3 m/sec to 0.5 m/sec.• Airflow Direction: Horizontal (Back to Front). • Airflow Configuration: Available in both vertical airflow configurations for clean and uniform air delivery. • Pre-Filter: G4 washable filter for trapping larger particles and easy maintenance. • Main Filter: HEPA Filter with 99.99% efficiency at 0.3 μm.• Working Environment: Ensures clean, contamination-free working environment when paired with HEPA filtration. • Main Power Switch: ON/OFF switch for safe and convenient machine operation. • Work Light: ON/OFF switch for clear visibility during operation. • UV Light: UV disinfection with timer to prevent microbial growth. • LED Lighting: Energy-efficient LED light for bright and uniform illumination. • Blower Control: High static pressure, dynamic balanced centrifugal blower with maintenance free direct drive motor specifically designed to maintain constant laminar air flow across the HEPA filter. The Blower ensures low noise less than 65db, low vibration, energy efficient operation and reliable continuous performance. Independent ON/OFF switch for airflow regulation. • Controller: Microprocessor control for precise operation of airflow, lighting, and safety functions. • Display: Digital display for blower operation, continuously monitors filter pressure drop and alerts in case of filter blockage or failure. • Front Door: Manual sliding glass door (also available with motorized automatic remote-control door). |
| 65 | Supply, Installation, Testing and Commissioning of Temperature & Humidity MeterFeatures• Backlit dual display of humidity and temperature. • 99 record data storage capacity. • Ergonomic design with belt clip and protective holster. • Quick-response capacitance sensor with protective cover. • Compact and lightweight design (190 g / 6.7 oz). • Measures temperature, relative humidity, dew point, and wet bulb. • Min/Max/Avg data hold function. • Low battery indicator. Technical Specifications• Temperature Measuring Range: -20°C to 60°C (-4°F to 140°F). • Temperature Accuracy: o ±0.5°C (0°C to 45°C) o ±1.0°C (-20°C to 0°C and 45°C to 60°C) o ±1.0°F (32°F to 113°F) o ±2.0°F (-4°F to 32°F and 113°F to 140°F) • Temperature Resolution: 0.1°C / 0.1°F. • Temperature Update Rate: 500 ms. • Temperature Sensor: NTC. • Relative Humidity Measuring Range: 5% to 95% RH. • Relative Humidity Accuracy: o ±2.5% RH (10% to 90% RH @ 23°C) o ±5.0% RH (<10% RH and >90% RH @ 23°C) • Relative Humidity Resolution: 0.1% RH. • Humidity Response Time: 90% of full range in 60 seconds with 1 m/s air movement. • Humidity Sensor: Electronic capacitance polymer film sensor. • Data Storage Capacity: 99 readings. |
| 66 | Supply, Installation, Testing and commissioning of pH Meter 5 point calibrationFeatures• 7-inch coloured capacitive touch screen with high resolution (1024 × 600) and high sensitivity. • Built-in microprocessor with intelligent functions including automatic calibration, ATC, data storage, clock display, USB output, function settings, wireless printing, and self-diagnosis. • Auto recognition of 25 pH buffer solutions with Europe & USA, NIST, and China standards. • Supports 1, 2, and 3-point pH calibration. • Auto recognition of 8 conductivity standard solutions with Europe & USA and China standards. • Supports PC connectivity. • Optional wireless Bluetooth printing and real-time data transfer to mobile phone. • Smart electrode status display for accurate operation. • Stores up to 1000 sets of test data. • Data can be transferred to a USB memory stick and opened in Microsoft Excel.Technical SpecificationspH Measurement• Measuring Range: (-1.999 to 19.999) pH • Resolution: 0.1 / 0.01 / 0.001 pH • Accuracy: Electrode: ±0.002 pH; Meter: ±0.01 pH • Calibration: Automatic 1, 2, or 3-point calibration • Buffer Standards: Europe & USA, NIST, China • Input Current: ≤ 1 × 10⁻¹² A • Input Impedance: ≥ 3 × 10¹² Ω • Stability: ±0.002 pH / 3 h • Temperature Compensation: 0–100°C (Automatic/Manual) mV Measurement• Measuring Range: -1999.9 mV to +1999.9 mV • Resolution: 0.1 mV • Accuracy: ±0.03% FS Conductivity Measurement• Conductivity Range: o 0.00–20.00 μS/cm o 20.0–200.0 μS/cm o 200–2000 μS/cm o 2.00–20.00 mS/cm o 20.0–200.0 mS/cm o 200–2000 mS/cm (K = 10) • TDS Range: 0–100 g/L • Salinity Range: 0–100 ppt • Resistivity Range: 0–100 MΩ•cm • Resolution: 0.01 / 0.1 / 1 μS/cm; 0.01 / 0.1 / 1 mS/cm • Accuracy: Electrode: ±0.5% FS; Meter: ±0.8% FS • Temperature Compensation: 0–100°C (Automatic) • Electrode Constant: 0.1 / 0.5 / 1 / 5 / 10 / 50 / 100 cm⁻¹ • Reference Temperature: 18°C, 20°C, 25°C |
| 67 | Providing and fixing of Weighing Scale• Voltage: 220 Volts; Wattage: 5 Watts• Package Contents: Weighing scale with Stainless steel pan.• Material: Iron; Color: Off-white; Dimension (L x W x H): 28 cm x 24 cm x 12 cm.• Stainless steel Platform measures 7 inches x 9 inches for Hygienic weighing. Maximum Weighing capacity: 30 kg, Precision: 1 gram. • Rust Proof Powder Coated Heavy-duty Metal Body. • Directly Plug-in 220V Power adapter. |
| 68 | Providing and fixing of Steel Shopping TrolleysTechnical Specifications• Material: SS 304 stainless steel. • Capacity: 60 Litres. • Heavy-duty stainless steel basket with seamless welded construction. • Corrosion-resistant, hygienic, and easy-to-clean finish. • Ergonomic stainless steel push handle for comfortable operation. • Four heavy-duty swivel castor wheels for smooth movement. |
| 69 | Providing and fixing of Platform TrolleysMaterial: Grade 304 or 316 stainless steel for chemical resistance and hygiene compliance.Capacity: Standard models support 150 kg to 300 kg; heavy-duty units exceed 500 kg.Dimensions: Common platforms span 750×500 mm to 1200×900 mm, with an 850 mm handle height.Castors: Non-marking polyurethane or rubber wheels with dual foot-operated locking brakes. |
| 70 | Providing and fixing of Sieve with Wooden Frame of suitable size as per site requirement. |
| 71 | Providing and fixing of Iron Trolley with TyresStructure: Heavy-duty Mild Steel (IS 2062) frame, welded construction, load-bearing capacity as per requirement (e.g., 500kg).Finish: Anti-corrosive primer and industrial-grade enamel paint or powder coating.Wheel Specs: Cast iron core with heavy-duty rubber-bonded tread.Bearings: High-quality, maintenance-free double ball bearings.Maneuverability: Combination of fixed and 360-degree swivel castor wheels |
| 72 | Supply, Installation, Testing and commissioning of Vacuum Cleaner1600W• Vacuum cleaner with Wet & Dry dual cleaning operations• Capacity: 21 Litres• Powerful 1600W motor• Strong 21.5 kPa suction power• Equipped with blower function• 360 degree four Swivel Wheels for easily cleaning in any direction• Accessories: Main unit, hose pipe, telescopic metal tube, floor brush, crevice nozzle, multipurpose brush, absorbing brush• 5 Meters long power cord |
| 73 | Supply, Installation, Testing and commissioning of Rotary ShakersPlatform Capacity: 49 × 500 mL FlasksPlatform Size: 770 × 770 mmTechnical Specifications• Platform capacity: 49 × 500 mL flasks. • Platform size: 770 × 770 mm. • Speed range: 1 to 250 RPM. • Digital speed control with variable RPM adjustment. • Timer range: 1 minute to 999 hours or continuous operation. • Maximum power consumption: 150 W. • Suitable for continuous and long-duration shaking applications. • Smooth and uniform orbital motion for consistent mixing. • Stable operation with low vibration and noise. • Operates on 230 V AC, 50 Hz, single-phase power supply. |
| 74 | Supply, Installation, Testing and commissioning of Induction Heater• Heating Element: 1 No. • Heating Technology: Induction. • Power Source: Corded Electric. • Fuel Type: Electric. • Power Rating: 2000 Watts. • Operating Voltage: 220 V AC. • Burner Type: Induction. • Ignition System: Electronic. • Control Type: Touch Control. • Installation Type: Counter-Top. • Digital Display: Yes. • Automatic Shut-Off: Yes. |
| 75 | Supply, Installation, Testing and commissioning of Humidifier• POWERFUL ROOM HUMIDIFIER: Efficiently manage humidity in spaces up to 320 ft² (30 m²) with a 5L/1.32Gallon tank designed to last up to 12 hours. • ADVANCED ESSENTIAL OIL DIFFUSION: Soothe congestion, dry skin, and coughing with the powerful mist from our separate essential oil case design. • EASY REFILL AND CLEANING: Convenient top-fill design allows for effortless refills and cleaning. With a wide 5.8IN opening• ULTRA-QUIET OPERATION: Experience tranquility with noise levels as low as 28dB, quieter than a whisper. No annoying humming, whistling, or crackling noises just soothing mist for better sleep and focus. Whether working or sleeping, enjoy the peaceful, calming ambiance provided by this near-silent humidifier.• CUSTOMIZABLE MIST CONTROL: Achieve ideal humidity with the stepless control knob, offering quick adjustments from low to high. The 360° nozzle allows you to direct the mist precisely where needed. Plus, safety is ensured with an automatic shut-off function and shortage indicator, making it perfect for worry-free use in any home. |
| 76 | Providing and fixing of Petri-dishes• Material: Borosilicate Glass / Medical Grade Polystyrene (Disposable), as specified. • Size: 90 mm Diameter × 15 mm Height. • Sterile and ready to use (for disposable type). • Transparent construction for easy observation of microbial growth. • Flat and smooth surface for uniform media distribution. • Tight-fitting lid to minimize contamination and moisture loss. |
| 77 | Supply, Installation, Testing and commissioning of Measuring Cylinder 250 ml• Capacity: 250 mL. • Material: Borosilicate Glass (3.3) / Polypropylene (PP), as specified. • Graduations: Permanent, easy-to-read printed graduations. • Accuracy: Conforms to Class A / Class B (as applicable). • Spout: Moulded pouring spout for easy and spill-free transfer of liquids. • Base: Wide hexagonal base for enhanced stability. • Chemical Resistance: Resistant to most laboratory chemicals and reagents. • Heat Resistance: Suitable for laboratory use; autoclavable (PP type) and heat-resistant (borosilicate glass type). |
| 78 | Supply, Installation, Testing, and Commissioning of premium-grade, heavy-duty Stainless Steel 304 (SS 304) modular racks suitable for Installation inside ISO Class 5 / Class 100 Clean Room Spawn laboratory. Rack shall be of Dimensions of 3000mm in Height, 1500mm in Width, and 485mm in Depth configured with 4 to 5 fully adjustable independent shelf levels. The main structural framework must be fabricated using heavy-duty SS 304 square pipes with a 16-gauge/1.5mm wall thickness featuring with clean, laser-etched vertical numbering slots to allow seamless height adjustments at a 25mm to 50mm pitch. To prevent air stagnation and support vertical laminar airflow crucial for preventing culture contamination the 1500mm x 485mm shelves must be constructed from 18-gauge SS 304 sheets with clean-punched 8mm to 10mm diameter perforations, capable of safely supporting a Uniformly Distributed Load (UDL) of at least 150 kg per shelf. Complete Job includes all sorts of costs including labour, material, labour, transportation etc. |
| 79 | Providing and fitting of 06 nos. Stools, 06 nos. LPG Cylinder (Big), 02 nos. Gas Bhatti, 02 nos. Steel Tub, 150 nos. Plastic Crates, 01 no. Gas Burner and Miscellaneous Lab Tools (PPE, Alcohol, Beakers, Gloves, Masks, etc.) as per site requirement with allied accessories required for fitting/installation of above mentioned equipments. Complete job includes cost of material, labour, transport and other taxes. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayOct 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender