Tender For Upgradation/ Improvement Of Medical Superintendent Office With Other Adjoining Offices Including Patient Area Under Ut Capex 2026-2027
Tender Value
1.02 Crore
Estimated cost
Bid Submission
11 Nov 2026
8 days left
EMD
2.05 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Upgradation/ Improvement Of Medical Superintendent Office With Other Adjoining Offices Including Patient Area Under Ut Capex 2026-2027
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles above 25 mm and upto 40 mm |
| 2 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : Of area of 3 sqm. and below |
| 3 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : Of area beyond 3 sqm |
| 4 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost ofmaking openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with:12.62.5 8 mm thick Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. |
| 5 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in- charge: 1:3:6 or richer mix (i/c equivalent design mix) |
| 6 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 7 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate. |
| 8 | Providing and laying Polished Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade includingrubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.11.68.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 9 | Providing and laying double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size of tile 600x600 mm |
| 10 | Providing and laying double charge Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete 600x600mm [kajaria,somnay,or equivalent] |
| 11 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)For fixed portion: Powder coated aluminum (minimum thickness of powder coated 50 microns) |
| 12 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)22.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns) |
| 13 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 14 | Providing & applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth. 1 mm thick |
| 15 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface |
| 16 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.13.90.2 Two coats |
| 17 | Providing and fixing of superior quality uPVC wall panels of approved make (Dumaplast/Alstone/Greenlam or Equivalent approved by Engineer-in-Charge), 8–10 mm thick, with tongue & groove interlocking, fixed on walls in line, level and plumb, including providing and fixing aluminium/GS framework (if required), stainless steel screws/clips/adhesive, all necessary trims such as corner profiles, edge beading, starter channels, joint covers, cutting for electrical fittings, finishing, scaffolding, carriage, labour and all incidentals complete as per directions of Engineer-in-Charge. Note. The sample of p.v.c panelling shall be approved from the competent authority. |
| 18 | Providing and fixing of Zebra blinds of approved colour madefrom 100% polyester yarn coated with fade resistant polymer toensure complete opaquely with zero light transmittance havingwidth of 280cm and weight of 148g/sqm +5% and fabric repeatsize having solid 13.5cm +5% and mesh 9cm+5% conforming torelevant IS parameters (Hunter Douglas / Johnson / Hillarys /Vista / marvel) including all fixtures and fittings complete in allrespect as per design and make approved by engineer in charge(Complete job). Note. The sample of Zebra Blinds shall be approved from the competent authority. |
| 19 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.9.21.1 With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws (35mm) |
| 20 | Providing and fixing C.P fittings 15mm nominal bore and fixtures (jaquar/cera or equivalent): Short nose bib cock |
| 21 | Providing and fixing C.P fittings 15mm nominal bore and fixtures (jaquar/cera or equivalent): Long nose bib cock |
| 22 | Providing and fixing C.P fittings 15mm nominal bore and fixtures (jaquar/cera or equivalent): Angle valve |
| 23 | Supplying/Providing/Fixing of health faucet ALD of superior quality including cost of material, labour carriage etc complete.(JET) |
| 24 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 25 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:18.2.1 W.C. pan with ISI marked white solid plastic seat and lid. |
| 26 | Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg |
| 27 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge |
| 28 | Providing and fixing 600x450 mm beveled edge mirror of superior glass(of approved quality) complete with 6 mm thick hard board ground fixedto wooden cleats with C.P. brass screws and washers complete. |
| 29 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the wallswherever required :18.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. |
| 30 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete , Semi rigid pipe 32 mm |
| 31 | Providing and fixing 100 mm sand cast iron grating for gully trap. |
| 32 | Providing and fixing toilet paper holder C.P. brass |
| 33 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 34 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc. |
| 35 | 15 mm dia. nominal bore |
| 36 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) |
| 37 | 19.36.1 15 mm nominal bore |
| 38 | 19.36.2 20 mm nominal bore |
| 39 | 19.36.3 25 mm nominal bore |
| 40 | Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make,weighing not less than 1.970 kg |
| 41 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore |
| 42 | Supplying/Providing/fixing of PVC bend 100mm dia of superior quality including cost of material, labour etc complete. |
| 43 | Providing and fixing un plasticized P.V.C. connection pipe with PTMTnuts, collars and bush of approved quality and colour19.65.2 15 mm nominal bore with 45 cm length. |
| 44 | Cutting holes up to 30x30 cm in walls including making good the same:19.67.1 With common burnt clay (non modular) bricks |
| 45 | Supplying/Providing/Fixing of P.V.C Pipe of superior quality including cost material,labour etc complete. |
| 46 | 75mm diameter |
| 47 | 100mm 6Kg pressure |
| 48 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm)of approved make and quality as per direction of Engineer-incharge |
| 49 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour:Waste coupling 31mm of 79 mm length and 62 mm breadth weighing not less than 45gms. |
| 50 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040mm bowl depth 225mm |
| 51 | Providing and fixing modular wooden wardrobe of approved design and size, made from 19 mm BWP/BWR waterproof plywood conforming to IS standards for sides, top, bottom, shelves, shutters and partitions, with 6 mm BWP plywood back panel, finished externally and internally with 1.0 mm decorative laminate (mica) of approved shade and make, including matching edge banding/PVC lipping, SS/aluminium handles, soft-close hinges, telescopic channels where required, hanging rod where required, locking arrangement, all necessary screws, adhesives, hardware, cutting, fitting, polishing of exposed edges, making necessary openings, complete as per approved drawing and direction of Engineer-in-Charge. The rate shall include all materials, labour, transportation, wastage, T&P, taxes, loading/unloading and all incidental charges. Measurement shall be in sft of front elevation of wardrobe complete. |
| 52 | Providing and fixing toughen glass of thickness 10 mm including cost of fitting, labour etc. complete job as approved by Engineer Incharge |
| 53 | Providing and fixing toughen glass of thickness 8 mm including cost of fitting, labour etc. complete job as approved by Engineer Incharge |
| 54 | Providing and fixing 19mm thick ply with fevicol and nails complete job as approved by Engineer Incharge |
| 55 | Providing and fixing 12mm thick ply with fevicol and nails complete job as approved by Engineer Incharge |
| 56 | Providing and fixing 6mm thick ply with fevicol and nails complete job as per the direction of Engineer Incharge |
| 57 | Providing and fixing superior quality of 1mm thick mica including grooving and fevicol nails complete job as per the direction of Engineer Incharge |
| 58 | providing and laying cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 59 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer- in-charge. (Cost of aluminum snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm) |
| 60 | Filling the gap in between aluminum frame and adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5mm widt |
| 61 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.9.102.1 125 mm |
| 62 | Providing and fixing aluminum casement stays, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 63 | Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Single rubber stopper |
| 64 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :300x10 mm |
| 65 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :300x16 mm |
| 66 | providing and fixing fly proof wire mesh complete job |
| 67 | providing and fixing antiskid floor tile 600x600mm with 20mm thick color and make as per the direction of Engineer Incharge |
| 68 | providing and fixing digital wall tile 600x300mm including 12mm plaster and grouting the joints with white cement and matching pigment color and make as per the direction of Engineer Incharge |
| 69 | Providing and fixing ACP sheet color and make as per the direction of Engineer Incharge |
| 70 | Disposal of mulba including loading and unloading. Complete job |
| 71 | Labour engaged for dismentling and shifting of mulba and shifting of construction material from outer area to working site |
| 72 | Engage semiskilled labour( plumber carpenter sweeper electrician aluminium fitter etc ) |
| 73 | Engage Welder with hire charges of welding set |
| 74 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia.0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class deodar wood(30mm) |
| 75 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Second class deodar wood Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender