Tender For Provn Of Hard Standing Of Kerb Side Area For Bio Medical Waste Handling At Comd Hosp (Wc) Chandimandir
Tender Value
43.40 Lakhs
Estimated cost
Bid Submission
07 Nov 2026
10 days left
EMD
86800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Panchkula → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Hard Standing Of Kerb Side Area For Bio Medical Waste Handling At Comd Hosp (Wc) Chandimandir
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil etc complete all as specified and as directed by Engineer-in-charge . |
| 2 | M & L for 150 mm thick cement concrete type D-2 (1:4:8) using 40mm graded crushed stone aggregate as in sub floors, sub bases etc all as specified and directed by Engineer - in - Charge. |
| 3 | M & L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.all as specified and directed by Engineer - in - Charge. |
| 4 | M & L for factory made chequered cement concrete designer prepolished glossy finished tiles 20cm x 20cm x 25mm thick with grey cement and pigments, heavy duty, set jointed and pointed in neat cement slurry and pigments as in floors over and including 15mm thick screed bed of cement mortar 1:6 complete all as specified and directed by Engineer - in - Charge. |
| 5 | M & L 75 mm thick cement concrete 1:2:4 type B–1 using 20 mm graded crushed stone aggregates as in flooring finished even and smooth without using extra cement all as specified and directed by Engineer - in - Charge . |
| 6 | M & L cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in kerbs or mud stops, rounded or chamfered on edges and similar work etc. all as specified and directed by Engineer - in - Charge . |
| 7 | Supplying and laying factory precast concrete saucer drain of length 300mm, width 450 mm and thickness 100mm (outer) & 75mm (centre) of M-25 grade in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without groove (Thickness of joints except at sharp curve shall not be more than 5mm) complete all as specified and directed by Engineer-in-charge. |
| 8 | M&L Brick work with sub class 'B' old size burnt bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:4 all as specified and directed by Engineer - in - Charge . |
| 9 | M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & fair without using extra cement all as specified and directed by Engineer - in - Charge . |
| 10 | M & L for two coats of synthetic enamel paint over a coat of primer over level plastered surfaces on kerb stone , wall including preparation of surfaces not exc 10 cm width or girth all as specified and directed by Engineer - in - Charge . |
| 11 | Factory made SFRC Pre-cast RCC manholes covers EHD-35 of size 900mm X 450mm X 100 mm thick, conforming to IS-12592 duly fixed on manhole /gully trap opening complete all as specified. |
| 12 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender