Tender For Comprehensive Repair/Maint Of Temp & Permanent Bldgs, Repair To Drains, Plain Cement Concrete Path, Hard Standing, Fencing, Security Walls, Parapet Wall & Allied Works At Awantipur And Balapur Under Ge 861 Ews
Tender Value
16.55 Lakhs
Estimated cost
Bid Submission
09 Nov 2026
20 days left
EMD
33500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Anantnag → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Repair/Maint Of Temp & Permanent Bldgs, Repair To Drains, Plain Cement Concrete Path, Hard Standing, Fencing, Security Walls, Parapet Wall & Allied Works At Awantipur And Balapur Under Ge 861 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Demolition cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level with and including removing rubbish material from building and thrown in low lying empty area complete all as specified and as directed by Engineer-in-charge. |
| 2 | Material & Labour for PCC 1:4:8 , Type D2 , using 40mm graded stone aggregates as in foundations, filling and mass concrete complete all as specified and as directed by Engineer-in-Charge. |
| 3 | Material & Labour for Brickwork with sub class ‘B’ burnt clay old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 with and including demolition of brick work , built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and as directed by Engineer-in-Charge. |
| 4 | Material & Labour for Walling of random rubble stone , uncoursed , well bonded,bedded and solidly hearted built in cement mortar 1:4 with and including demolition of brick work / stone masonry, built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and directed by Engineer-in-Charge. |
| 5 | Material and labour for raised pointing in CM (1:4) to square rubble,coursed and uncoursed rubble masonry completre all as specified and directed by Engineer-in-Charge. |
| 6 | Material and labour for Plain cement concrete (1:2:4) type B-I, using 20 mm graded stone aggregates as in bands, bedding, benching of manholes, coping, roof kerbs or mud stops, rounded or chamfered on edges etc including necessary form work complete all as specified and as directed by Engineer-in-charge. |
| 7 | Material and labour for Extra over Granite or Trap stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling stone, uncoursed or brought upto courses with hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 40mm complete all as specified and as directed by Engineer-in-Charge. |
| 8 | Material and labour for Plain cement concrete (1:3:6) type C-2, using 40 mm graded stone aggregates as in drain, surface channel complete all as specified and as directed by Engineer-in-charge. |
| 9 | Material and labour for Rendering 15mm thick in Cement Mortar 1:4 , on fair faces of brick work or concrete surfaces of walls , finish even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 10 | Material and Labour for Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc. complete all as specified and as directed by Engineer-in- charge. Note:- Inner girth shall only be measured for payment. Nothing extra shall be paid on this account. |
| 11 | Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge. |
| 12 | Material & Labour for 100 mm thick PCC 1:4:8 ,Type-D2 ,using 40mm graded stone aggregates as in sub base of flooring complete all as specified and directed by Engineer-in-Charge. |
| 13 | Material & Labour for glossy finished coloured chequred cement concrete tiles of area each tiles not exc 0.18 sqm with grey cement and pigment laid over and including 20mm thick cemnt screed bed in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor complete all as specified and directed by Engineer-in-Charge. |
| 14 | Material & Labour for Machine Pressed Precast Interlocking paver block with grey cement and no pigment, factory made, any shape and size, conforming to IS 15658-2006 of 80 mm thickness, made out of M-40 grade concrete laid over sand cushioining complete all as specified and as directed by Engineer-in-charge. Note:Sand cushioning shall be measured and paid seperately under approriate item of Schedule'A' BoQ. |
| 15 | Material & Labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Material and labour for 75 mm thick PCC (1:3:6) Type C-2 using 40mm graded stone aggregate as in flooring, hard standing, plinth protection / path etc. finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge |
| 17 | Dismantling timber scantlings 40 sq. cm in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in any position complete all as specified and directed by Engineer-in-Charge. |
| 18 | Supply & Fixing Mild steel work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) Fe 410 -W (Gde- E- 250) quality-A includingdistance pieces, cleats etc. complete all as speicied and as directed by Engineer in charge. |
| 19 | Material & Labour in replacement Pre-painted galvalume aluminium zink coating GI based corrugated steel sheet 0 50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ Clading to wall, fixed with self tapping screws, complete all as specified and directed by Engineer-in-Charge. |
| 20 | Material & Labour in replacement Pre-painted galvalume aluminium zink coating GI based Plain steel sheet .50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/Clading to wall, Ridge and eaves board, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge. |
| 21 | Material & Labour for 25 mm thick PCC 1:2:4 Type B-0 (using 12.5 mm graded stone aggregate) as in sub base of floor complete all as specified and directed by Engineer-in-Charge. |
| 22 | Material & Labour for Non skid ceramic coloured joint free tiles , thickness 7mm to 8mm thick (square/ rectangular), colour as approved by Engineer-in-charge area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 15mm thick screed bed in cement mortar 1:4 with and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) with and including removing rubbish material from building and thrown in low lying empty area complete all as specified and as directed by Engineer-in-charge. |
| 23 | Material & Labour for Glazed Coloured Ceramic tiles , size 350mm x 250mm / 450mm x 350mm x 7mm to 8mm thick, colour as approved by Engineer-in-charge as in vertical surfaces set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 10mm thick rendering in cement mortar 1:4 with and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) with and including removing rubbish material from building and thrown in low lying empty area complete all as specified and as directed by Engineer-in-charge. |
| 24 | Material & Labour for Virified Ceramic tiles dark shade 10mm thick (square/rectangular) polished, (shade as approved by Engineer-in-charge ) , area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured/ shade cement to match the colour / shade of tiles , laid over with and including 15mm thick screed bed in cement mortar 1:4 with and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) with and including removing rubbish material from building and thrown in low lying empty area complete all as specified and as directed by Engineer-in-charge. |
| 25 | Material & Labour 2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm splayed chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge. |
| 26 | Material & Labour 2nd class hard wood plain fillets square/rectangular or triangular in section , clean sawn, bull nosed , splayed, chamfered or rounded on one edge or face secured with nails or brads of sectional area exceeding 06 Sqcm but not exceeding 13 Sqcm splayed chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge. |
| 27 | Material and Labour in replacement 4mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face fixed in ceiling flat and fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge. |
| 28 | Material and Labour in replacement 4mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face fixed in wall and fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge. |
| 29 | Material and labour for Rendering 10mm thick in Cement Mortar 1:6 , on fair faces of brick work or concrete surfaces of walls , finish even & smooth without using extra cement incl Taking down cement or cement lime plaster from brick wall or concrete surfaces etc including racking out joints, hacking for key & scrubbing down with water etc including removing rubbish material from site and thrown in low lying empty area (as per direcction of AGE/JE) complete all as specified and as directed by Engineer-in-charge. |
| 30 | Material and labour for Rendering 15mm thick in Cement Mortar 1:4 , on fair faces of brick work or concrete surfaces of walls , finish even & smooth without using extra cement incl Taking down cement or cement lime plaster from brick wall or concrete surfaces etc including racking out joints, hacking for key & scrubbing down with water etc including removing rubbish material from site and thrown in low lying empty area (as per direcction of AGE/JE) complete all as specified and as directed by Engineer-in-charge. |
| 31 | Material and labour for preparation of new plastered surface of walls with and including applying two coats of Oil Emulsion Distemper over with and including one coat of alkali resistant primer over with and including 3.00mm thick wall care putty (as approved by Engineer-in-charge for smooth & even surface) complete all as specified and directed by Engineer-in-Charge. |
| 32 | Material and labour for preparation of new surface of walls, with and including applying two coats of cement base paint ,over with and including one coat of alkali resistant priming paint complete all as specified and directed by Engineer-in-Charge. |
| 33 | Material & Labour for preparation of old decorative surface of wall, (with using by brooming down or steel wire burshing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots ) with and including applying two coats of cement based paint over one coat of alkali resistent primer complete all as secified and as directed by Enigneer-in-Charge. |
| 34 | S&F in replacement vitreous china wash basin, white, flat back, size 630mm x 450 mm excluding taps, waste , chain and plug and proccelain stopper but including brackets complete all as specified and directed by Engineer-In-Charge. |
| 35 | Supply and Fixing in replacement Vitreous china wash hand basin, Vitreous china white, flat back, size of 550mm x 400 mm with Mild steel brackets, with and including cutting for and pinning in ends of brackets or erecting stand, with and including waste fittings of brasschromium plated ,with and including 32mm dia PVC waste pipe of required length complete all as specified and directed. as directed by Engineer-in-Charge. |
| 36 | Supply & Fixing in replacement water closet vitreous china squatting pan, Orissa pattern size 630mm x 450mm white with integral foot rests with and including provision of lime concrete bedding with and including 110mm bore PVC (SWR)'P' Trap and connection to drain and to flushing pipe anti symphonage pipe complete all as specified and directed by Engineer-in-Charge. |
| 37 | Supply & Fixing in replacement water closet vitreous china squatting pan, Orissa pattern size 580mm x 440mm white with integral foot rests with and including provision of lime concrete bedding with and including 110mm bore PVC (SWR)'P' Trap and connection to drain and to flushing pipe anti symphonage pipe complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply and Fixing in replacement PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle , with and including brackets, with and including 32 mm dia flush pipe of polyethylene of low or high density of PVC complete all as specified and as directed by Engineer-in- charge. |
| 39 | Supply and fixing in replacement 15 mm bore brass Chromium Plated mixer (ISI marked) for mixing hot and cold water , screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer-in-Charge. |
| 40 | Supply and Fixing in replacement 15mm bore Pillar tap fancy type Chromium Plated , (ISI marked) cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. |
| 41 | Supply & Fixing in replacement 15mm bore PVC connection with PTMT nuts of 450mm long complete all as specified and directed by Engineer-in-Charge. |
| 42 | Supply and fixing in replacement 15mm bore bib tap cast copper alloy, chromium plated, fancy type (ISI marked) with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge. |
| 43 | Supply and fixing in replacement 20 bmm bore bib tap cast copper alloy, fancy type (ISI marked) with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge. |
| 44 | Supply and fixing in replacement 32mm dia waste coupling of PTMT (half or full threaded), (minimum weight 32mm-45 gms / 40mm-60 gms) complete all as specified and directed by Engineer-in-Charge. |
| 45 | Supply and fixing in replacement 15 mm bore stop valve , Chromium Plated, cast copper alloy (ISI marked) screwed down , high pressure with crutch or butterfly handle fancy type complete all as specified and directed by Engineer-in-Charge. |
| 46 | Supply and fixing in replacement 600mm x 450mm size bevelled edge mirror selected quality 5mm thick glass mounted on 6mm thick commercial ply and fixed to wooden plugs with chromium plated brass screws and cup washers, including aluminium frame / beading alround made of aluminium channel, complete all as specified and directed by Engineer-in-Charge. |
| 47 | Supply & Fixing 15mm bore GI tubing medium grade with all new fittings to walls and ceilings or laid in floors with and including taking up or down steel tubing 15mm bore and connection complete all as specified and directed by Engineer-in-Charge.Note: if Excavation required , Excavation and earth work shall be measured and paid seperately under appropriate items of schedule 'A' BoQ. |
| 48 | Supply & Fixing 20mm bore GI tubing medium grade with all new fittings to walls and ceilings or laid in floors with and including Taking up or down steel tubing 15mm bore and connection complete all as specified and directed by Engineer-in-Charge.Note: if Excavation required , Excavation and earth work shall be measured and paid seperately under appropriate items of schedule 'A' BoQ. |
| 49 | Supply and Fixing in replacement vitreous china wash down water closet pan ( pedestal pattern ) white , with and including stainless steel Jet , with and including ‘P’ or ‘S’ trap , with and including seat cover complete all as specified and directed by Engineer-in-Charge. |
| 50 | Supply & fixing in replacement Rotational moulded polyethylene water storage tank white colour of capacity 1000 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position with and including Ball valve high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 20mm-210 gram) complete all as specified and as directed by Engineer-in-charge. Note: The rate of 20mm bore ball valves, high pressure of PTMT is included in this iterm and nothing shall be paid extra on this account. |
| 51 | Supply and Fixing in replacement Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by Engr-in-charge. |
| 52 | Supply & Fixing in replacement Brass Chromium Plated tubular towel rail, 20mm dia, D type, 60cm long between flanges and bracket complete all as specified and directed by Engineer-in-Charge. |
| 53 | Taking down carefully aluminum / copper point wiring on Teak Wood Batten / in conduit / with conduit / in casing and capping(light /Fan / socket or power) complete with and including taking down fittings such as switches, ceiling roses, pendants, Regulators, sockets, light fittings etc complete all as specified and directed by Engineer-in-Charge. Notes:(i) The weight of aluminium scrap, copper scrap and scrap iron for schedule of credit shall be ascertain by BOO as ordered by GE.The copy of BOO duly countersinged by GE shall be enclosed with final Bill.(ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface shall be measured and paid seperately. |
| 54 | Material and labour for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits),with 1.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked , with and including PVC casing and capping of medium grade of suitable size and run on wall / surface with all fittings (ISI Marked) with and including one single core 1.5 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) (as in green colour) as continues earth wire connected to earth dolly etc. controlled by one switch for one light point/ fan point /Bell point with and including suitable size of PVC Box directed by Engineer- in- Charge including cutting, chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge. Notes for serial item nos.54.00 to 57.00 : (i) switches one way 5 /6 Amp , Switch socket combination 2 in 1, 3 pin, 5 Amp & Switch socket combination 2 in 1, 3 pin, 15 Amp shall be measured and paid seperately under respective items of Schedule'A' BoQ.(ii) The rate of cutting chases (as required) and making good surfaces to match with adjoining surface is included in this item and nothing shall be paid extra on this account. |
| 55 | All as per srl item No. 54.00 here- in- before but for Switch socket combination 2 in 1, 3 pin, 5 Amp on independent board complete all as specified and directed by Engineer-in-Charge. |
| 56 | All as per srl item No. 54.00 here- in- before but forSwitch socket combination 2 in 1, 3 pin, 5 Amp on Same board complete all as specified and directed by Engineer-in-Charge. |
| 57 | All as per srl item No. 54.00 here-in-before but 4 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked with and including one single core 4 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) as continues earth wire connected to earth dolly etc for Switch socket combination 2 in 1, 3 pin, 15 Amp complete all as specified and directed by Engineer-in-Charge. |
| 58 | Supply and fixing ceiling rose surface bakelite 65mm x 50mm three terminals ISI Marked complete all as specified and directed by Engineer-in-Charge. |
| 59 | Supply and fixing Switch piano flush type 5 Amp single pole one way ISI marked complete all as specified and directed by Engineer-in-Charge. |
| 60 | Supply & Fixing Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal 240 volt (ISI Marked ) complete all as specified and directed by Engineer-in-Charge. |
| 61 | Supply & Fixing Switch socket combination 2 in 1, 3 pin, 15 Amp flush type universal 240 volt (ISI Marked )complete all as specified and directed by Engineer-in-Charge. |
| 62 | Supply and fixing Lamp holder (Angular/Straight )ISI marked , insulated body , with back plate for batten fittings complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply and fixing Plug top 3 pin 5/6 amps 230 volts, complete all as specified and directed. |
| 64 | Supply and fixing Plug top 3 pin 15/16 amps 230 volts, complete all as specified and directed. |
| 65 | Supply & fixing PVC Gang box surface type suitable for fixing of 5 pin 5 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge. Note: Switch 5 Amp single pole and Socket out let 5 Amp shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 66 | Supply & fixing PVC Gang box surface type suitable for fixing of 5 pin 15 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge. Note: Switch 15 Amp single pole and Socket out let 15 Amp shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 67 | Supply and fixing LED 9 watt pin type bulb complete all as specified and as directed by Engineer-in-Charge. Notes:(a) Contractor has to furnish a replacement warranty of 02 years for LED Bulb complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. |
| 68 | Supply and fixing in replacement Batten fitting 2 Feet Long , LED mirror light fiting 9/10 watt, 6000K, polycarbonate body and all other accessories fitting arrangements all other accessories fitting arrangements complete all as per manufacturer's instructions with and including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector complete all as specified and as directed by Engineer-in-Charge. Notes:(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 69 | Supply and fixing in replacement LED lights fitting 1 x 20W, 220V, AC decorative box type with driver, holder including LED tube light 20 watt complete all as per manufacturer's instruction with and including electric connection with using flexible copper wire twin core upto ceiling rose to light fitting complete all as specified and directed by Engineer-in-Charge. Notes:(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 70 | Supply & Fixing in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp complete all as per manufacturer's instructions suitable for roof ceiling with and including connecting up with driver from ceiling rose with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. Notes:-(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 71 | Supply & Fixing in replacement LED luminaire round/squre shape 15 watts 220 V AC surface/recessed type with hight efficiency PMMA diffuser soft glare free light complete with driver, holder & LED lamp suitable for foof ceiling/surface complete all as per manufacturer's instructions suitable for roof ceiling with and including connecting up with driver from ceiling rose with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. Notes:-(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 72 | Supply and fixing in replacement sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB SPN 4 way 230 V AC with 200 Amp rated copper bus bar, Double Door, dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items.(ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account. |
| 73 | Supply and fixing in replacement sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB SPN 8 way 230 V AC with 200 Amp rated copper bus bar, Double Door, dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items.(ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account. |
| 74 | Supply and fixing MCCB 63 Amp , AC 415 Volt, 4 Pole , rupturing capacity not less than 16 KA . complete all as specified and directed by Engineer-in-charge. |
| 75 | Supply and fixing MCB SP 6 to 32 Amps, 230 volts , AC supply , rupturing capacity not less than 10KA,' C' Curve ,ISI Marked, with and including necessary attachment , thimbles etc complete all as specified and directed by Engineer-in-charge. |
| 76 | Supply and fixing MCB SPN 32 Amp , rupturing capacity not less than 10 KA 'C' curve 230 V AC, 50 Hz ,ISI Marked, with and including necessary attachment , thimbles etc. complete all as specified and directed by Engineer-in-charge. |
| 77 | Supply and fixing MCB SPN 40 Amp , rupturing capacity not less than 10 KA 'C' curve 230 V AC, 50 Hz ,ISI Marked, with and including necessary attachment , thimbles etc. complete all as specified and directed by Engineer-in-charge. |
| 78 | Supplying and fixing MCB TPN 40Amps -100 Amps , 415 Volt AC, 'C' curve, ISI Marked, rupturing capacity not less than 10KA, with and including necessary attachment , thimbles etc complete all as specified and directed by Engineer-in-charge. |
| 79 | Material and Labour in replacemnt Sub main wiring with two single core of size 1.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked , with and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) , drawn in , with and including one single core of size 1.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked as in contineous earth conductor cable connected to earth dolly complete all as specified and as directed by Engineer-in- charge. (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge. Notes:-(a) Cost of PVC casing and capping medium grade of suitable size , fittings and earth wire included in sub main wiring. (b) Three single core 1.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked with and Cost of PVC casing and capping medium grade of suitable size and fittings shall be measured as one length. |
| 80 | Material and Labour in replacemnt Sub main wiring with two single core of size 2.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked , with and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) , drawn in , with and including one single core of size 2.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked as in contineous earth conductor cable connected to earth dolly complete all as specified and as directed by Engineer-in- charge. (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge. Notes:-(a) Cost of PVC casing and capping medium grade of suitable size , fittings and earth wire included in sub main wiring. (b) Three single core 2.5 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked with and Cost of PVC casing and capping medium grade of suitable size and fittings shall be measured as one length. |
| 81 | Material and Labour in replacemnt Sub main wiring with two single core of size 4.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked , with and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) , drawn in , with and including one single core of size 4.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked as in contineous earth conductor cable connected to earth dolly complete all as specified and as directed by Engineer-in- charge. (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge. Notes:-(a) Cost of PVC casing and capping medium grade of suitable size , fittings and earth wire included in sub main wiring. (b) Three single core 4.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked with and Cost of PVC casing and capping medium grade of suitable size and fittings shall be measured as one length. |
| 82 | Supply and Fixing in replacement service cable 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed of nominal cross sectional area 16 Sqmm x 2.00 core complete all as specified and as directed by Engineer-in-charge. |
| 83 | Taking down old unserviceable service cable/underground (UG) cable of any size, including removal of unserviceable bricks/PCC cable covers, with and including Supply and laying or fixing or laid in trenches/ ducts/ through pipes/ in floors / under roads/ hard standing /along poles and testing LT cable XLPE, PVC insulated screened, bedded, galvanised steel strip or wire armourd cable (heavy duty) 1100 volt grade with aluminium conductor having cross sectional area 16 Sqmm 4.00 core conforming to IS-7098 (Part-I -1988) complete all as specified and as directed by Engineer-in-Charge. Notes:(a) Earth work such as excavation, returning filling and removal shall be measured and paid for separately under relevant items of Schedule 'A' BoQ..(b) Where new/old cable is laid along the same alignment/location, earth work such as excavation, returning filling and removal shall be measured and paid only once. No duplicate measurement shall be admissible in this regard. |
| 84 | Supply & fix in replacement medium grade PVC casing and capping of size 20 mm dia, with and including all accessories complete as specified and as directed by Engineer-in-Charge. |
| 85 | Supply and Fixing in Replacement water heater (Geyser) Auto restrat and safety measures type electrical operated 230/240 Volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, plug top, etc. required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts,nuts including testing after installation complete all as specified & directed by Engr-in- Charge. |
| 86 | Supply & Fixing in Replacement Exhaust fan 300 mm sweep , made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and directed by Engineer-in-Charge. |
| 87 | Supply and fixing in replacement Wall fan 450mm high speed, 230 volts single phase with jerk free oscillation, smooth running, three blades, pull cords incduding fixing arrangement complete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply & Fixing in replacement LED Security street light fitting 35 Watt 230 V AC outdoor type, energy saving and environment friendly light fitting with electronic gear housed with high pressure die cast aluminum housing LED street light luminaires complete with IP66 protection including all accessories complete all as specified and directed by Engineer-in-Charge. Notes:-(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 89 | Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysNov 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender