Tender For Supply And Installation Of One 16-Meter High-Mast Light Near The Water Tank In Gram Sandhawali, One 12.5-Meter Cm High-Mast Light Near Shiv Mandir Junior High School In Ram Makhiyali, And High-Mast Lighting Near The Upper Primary School In Gram
Tender Value
13.28 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
9 days left
EMD
28000
Bank guarantee accepted
Document Fee
2360
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Muzaffarnagar → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Supply And Installation Of One 16-Meter High-Mast Light Near The Water Tank In Gram Sandhawali, One 12.5-Meter Cm High-Mast Light Near Shiv Mandir Junior High School In Ram Makhiyali, And High-Mast Lighting Near The Upper Primary School In Gram Sandhawali, Muzaffarnagar City.
BOQ
| Sl. No. | Item Description |
| 1 | xzke la/kkoyh esa mPp izkFkfed fo|ky; ds ikl 01 ux] 12-5 eh0 lseh gkbZekLV ykbZV dk dk;ZA |
| 2 | Supply & fixing of 12.50 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 310 mm base plate 25 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site requirement along with foundation bolts nuts, washers, anchor plates etc complete in all respect as per direction of E/I. etc (S.I No. 651/2018) |
| 3 | Supply and laying of aluminium insulated armoured served sheathed cables 1100 Volts conductor PVC grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size. The armouring of the cable shall be properly connected with the earth conductor by clamps etc complete in all respect as per direction of E/I etc (S.I No 501 (H)/2018 10 sq. Mm 4 core) |
| 4 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 Watt. Confirming to IP 66 protection complete in all respect as per direction of E/I etc. (Which are registered and approved at least by PWD) (S.I No 1454/2018 CAT-AAA) |
| 5 | Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of two no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all each respect. S.I No- 703/2018 |
| 6 | Supply and fixing of 63 Amp. 415 V metal clad TPN HRC type switch fuse unit complete with HRC fuse on angle iron bracket complete in all respect. (S.I. No 327/2018 Elec) |
| 7 | Supply and fixing of single unit LED aviation Obstruction light complete with transformer and LED spiral etc complete in all respect. (S.I No-409/2018) |
| 8 | Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. Complete in all respect as per direction of the Engineer-in-Charge (S.I No. 504 C/2018) |
| 9 | S/L of following size DWC HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excuding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm &ID-51 mm nominal) DSR S.N14.16.1/2022 |
| 10 | xzke&la/kkoyh esa ikuh dh Vadh ds ikl 01 ux] 16 eh0 gkbZekLV ykbZV dk dk;ZA |
| 11 | Supply & fixing of 16 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 360 mm base plate 32 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site requirement along with foundation bolts nuts, washers, anchor plates etc complete in all respect as per direction of E/I. etc (S.I No. 652/2018) |
| 12 | Supply and laying of aluminium insulated armoured served sheathed cables 1100 Volts conductor PVC grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size. The armouring of the cable shall be properly connected with the earth conductor by clamps etc complete in all respect as per direction of E/I etc (S.I No 501 (H)/2018 10 sq. Mm 4 core) |
| 13 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 Watt. Confirming to IP 66 protection complete in all respect as per direction of E/I etc. (Which are registered and approved at least by PWD) (S.I No 1454/2018 CAT-AAA) |
| 14 | Supply and fixing of Safe Earthing Electrode T-39 (Hot-Dip Galvanized), Length 2000mm, outer pipe 76mm inner Dia 38mm termina Dia 12 mm,outer GI pipe of 16 SWG and inner GI pipe of 12 SWG with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25 X 3 GI. Strip will be extra)Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. S.I no 725(D)/2018 |
| 15 | Supply and fixing capacity of automatic street light cubicle controal panel painted woth anticorrosive alkali ad acid proof paint consistiing of time swithc TSO 100 series with contactors, HRC fuses, isolating switch metering insrument & instrument box with CTs etc. in case of TPN, complete in all respect. 40A TPN(S.I No 807(c)(ii)2018 ) |
| 16 | Supply and fixing of single unit LED aviation Obstruction light complete with transformer and LED spiral etc complete in all respect. (S.I No-409/2018) |
| 17 | Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. Complete in all respect as per direction of the Engineer-in-Charge (S.I No. 504 C/2018) |
| 18 | S/L of following size DWC HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excuding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm &ID-51 mm nominal) DSR S.N14.16.1/2022 |
| 19 | xzke&HkSalh ds eq[; pkSjkgs ij 01 ux]12-5 eh0 lseh gkbZekLV ykbZV dk dk;ZA |
| 20 | Supply & fixing of 12.50 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 310 mm base plate 25 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site requirement along with foundation bolts nuts, washers, anchor plates etc complete in all respect as per direction of E/I. etc (S.I No. 651/2018) |
| 21 | Supply and laying of aluminium insulated armoured served sheathed cables 1100 Volts conductor PVC grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size. The armouring of the cable shall be properly connected with the earth conductor by clamps etc complete in all respect as per direction of E/I etc (S.I No 501 (H)/2018 10 sq. Mm 4 core) |
| 22 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 Watt. Confirming to IP 66 protection complete in all respect as per direction of E/I etc. (Which are registered and approved at least by PWD) (S.I No 1454/2018 CAT-AAA) |
| 23 | Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of two no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all each respect. S.I No- 703/2018 |
| 24 | Supply and fixing of 63 Amp. 415 V metal clad TPN HRC type switch fuse unit complete with HRC fuse on angle iron bracket complete in all respect. (S.I. No 327/2018 Elec) |
| 25 | Supply and fixing of single unit LED aviation Obstruction light complete with transformer and LED spiral etc complete in all respect. (S.I No-409/2018) |
| 26 | Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. Complete in all respect as per direction of the Engineer-in-Charge (S.I No. 504 C/2018) |
| 27 | S/L of following size DWC HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excuding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm &ID-51 mm nominal) DSR S.N14.16.1/2022 |
| 28 | xzke&ef[k;kyh esa fLFkr f'ko eafnj] twfu;j gkbZ Ldwy ds ikl 01 ux]12-5 eh0 lseh gkbZekLV ykbZV dk dk;ZA |
| 29 | Supply & fixing of 12.50 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 310 mm base plate 25 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site requirement along with foundation bolts nuts, washers, anchor plates etc complete in all respect as per direction of E/I. etc (S.I No. 651/2018) |
| 30 | Supply and laying of aluminium insulated armoured served sheathed cables 1100 Volts conductor PVC grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size. The armouring of the cable shall be properly connected with the earth conductor by clamps etc complete in all respect as per direction of E/I etc (S.I No 501 (H)/2018 10 sq. Mm 4 core) |
| 31 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 Watt. Confirming to IP 66 protection complete in all respect as per direction of E/I etc. (Which are registered and approved at least by PWD) (S.I No 1454/2018 CAT-AAA) |
| 32 | Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of two no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all each respect. S.I No- 703/2018 |
| 33 | Supply and fixing of 63 Amp. 415 V metal clad TPN HRC type switch fuse unit complete with HRC fuse on angle iron bracket complete in all respect. (S.I. No 327/2018 Elec) |
| 34 | Supply and fixing of single unit LED aviation Obstruction light complete with transformer and LED spiral etc complete in all respect. (S.I No-409/2018) |
| 35 | Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. Complete in all respect as per direction of the Engineer-in-Charge (S.I No. 504 C/2018) |
| 36 | S/L of following size DWC HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excuding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm &ID-51 mm nominal) DSR S.N14.16.1/2022 |
| 37 | eqt¶Qjuxj 'kgj ds okMZ ua0 26 ?kkleaMh esa 04 ux] 150 okWV ¶yM ykbZV yxk;s tkus dk dk;ZA |
| 38 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 Watt. Confirming to IP 66 protection complete in all respect as per direction of E/I etc. (Which are registered and approved at least by PWD) (S.I No 1454/2018 CAT-AAA) |
| 39 | Supply and laying of aluminium insulated armoured served sheathed cables 1100 Volts conductor PVC grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size. The armouring of the cable shall be properly connected with the earth conductor by clamps etc complete in all respect as per direction of E/I etc (S.I No 501 (H)/2018 10 sq. Mm 4 core) |
| 40 | Supply and fixing of 63 Amp. 415 V metal clad TPN HRC type switch fuse unit complete with HRC fuse on angle iron bracket complete in all respect. (S.I. No 327/2018 Elec) |
| 41 | Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connection etc. Complete in all respect as per direction of the Engineer-in-Charge (S.I No. 504 C/2018) |
| 42 | LED Board (MDA) Acrylic sheet .(size-18 inch x 12 inch) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender