Tender For Construction Of Shree Shyama Prasad Mukherjee Convention Centre, Dausa
Tender Value
5.82 Crore
Estimated cost
Bid Submission
12 Nov 2026
2 days left
EMD
11.65 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dausa → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Shree Shyama Prasad Mukherjee Convention Centre, Dausa
BOQ
| Sl. No. | Item Description |
| 1 | Supply, Installation, Testing & Commissioning of a high-performance 15\\" installation loudspeaker, having a frequency response of 55 Hz–20 kHz (–3 dB) / 40 Hz–20 kHz (–10 dB). The loudspeaker shall deliver 600 W AES (2400 W peak) power handling with a maximum output of 128 dB continuous and 134 dB peak SPL. Coverage pattern shall be 90° (H) × 50° (V) or better, with a rotatable horn for flexible installation. The system shall support passive (1.2 kHz crossover) or bi-amp operation with 8 Ω nominal impedance. The LF section shall consist of a 15\\" driver with 550 W AES / 2200 W peak rating, 3\\" copper voice coil, ferrite magnet, optimized airflow, and an aluminum demodulation ring for reduced distortion. The HF section shall include a 1.4\\" exit compression driver rated at 50 W AES / 200 W peak with a 2.5\\" ferrite voice coil, mounted on a Contour waveguide to ensure uniform coverage. The cabinet shall be equipped with dual SpeakOn input/thru connectors for easy system integration. Approved Make: British Acoustics / Meyer Sound / Martin Audio / d&b audiotechnik. |
| 2 | Supply, installation, testing & commissioning of Loudspeaker mounting arrangement for Main FOH Speaker provides secure installation with adjustable brackets, supporting both horizontal and vertical setups for optimal sound coverage. Approved Make :- Netmas |
| 3 | Supply, installation, testing, and commissioning of a twin 18\\" passive subwoofer system with 32 Hz–190 Hz (–3 dB) / 37 Hz–200 kHz (–10 dB) frequency response. The system delivers 2400 W AES (9600 W peak) with 136 dB continuous / 142 dB peak SPL, omni-directional coverage, cardioid presets, 4 Ω nominal impedance, and active 80–120 Hz crossover. LF section: two 18\\" long-excursion drivers connected in parallel, 4\\" copper voice coil, ferrite magnet, 3-layer resistance coating, optimized airflow for minimal power compression, and aluminum demodulation ring. Features dual SpeakOn input/thru connectors. Approved Make: British acoustics/ Meyer sound/Martin audio/d&b audiotechnik. |
| 4 | Supply, installation, testing, and commissioning of 2 × 6\\" high-performance Front Fill speakers with 90 Hz–16 kHz (–3 dB) / 77 Hz–16 kHz (–10 dB) frequency response. The system delivers 300 W AES (1200 W peak), 120° horizontal × 60° vertical dispersion, 8 Ω nominal impedance, 2.1 kHz passive crossover (or bi-amplified), and dual SpeakOn input/thru connectors. LF section: two 6\\" drivers in parallel, 150 W AES (600 W peak) each, 1.3\\" copper voice coil, ferrite magnet, 3-layer resistance coating, optimized airflow, and aluminum demodulation ring. HF section: 0.75\\" exit compression driver with 1\\" ferrite voice coil and contour waveguide for consistent coverage. Approved Make: British acoustics/ Meyer sound/Martin audio/d&b audiotechnik. |
| 5 | Supply, installation, testing & commissioning of Loudspeaker mounting arrangement for Front fill Speaker provides secure installation with adjustable brackets, supporting both horizontal and vertical setups for optimal sound coverage. Approved Make :- Netmas |
| 6 | Supply, installation, testing, and commissioning of an 8\\" performance installation speaker with 72 Hz–20 kHz (–3 dB) / 60 Hz–20 kHz (–10 dB) frequency response. The system delivers 250 W AES (1000 W peak) with 120 dB continuous / 126 dB peak SPL, 90° horizontal × 50° vertical dispersion, user-rotatable horns, 1.8 kHz crossover or bi-amped operation, and 8 Ω nominal impedance. LF section: 8\\" driver, 220 W AES (880 W peak), 1.3\\" copper voice coil, ferrite magnet, enhanced airflow, and aluminum demodulation ring. HF section: 0.75\\" exit compression driver, 30 W AES (120 W peak), 1\\" ferrite voice coil, with contour waveguide for consistent coverage. Features dual SpeakOn input/thru connectors. Approved Make: British acoustics/ Meyer sound/Martin audio/d&b audiotechnik. |
| 7 | Supply, installation, testing & commissioning of Loudspeaker mounting arrangement for Side fill Speaker provides secure installation with adjustable brackets, supporting both horizontal and vertical setups for optimal sound coverage. Approved Make :- Netmas |
| 8 | Supply, installation, testing, and commissioning of a 12\\" powered 2-way portable speaker with a frequency response of 64 Hz–20 kHz (–3 dB) and 49 Hz–20 kHz (–10 dB). The system delivers 500 W AES (2000 W peak) LF and 50 W AES (200 W peak) HF with 122 dB continuous / 128 dB peak SPL, 90° horizontal × 50° vertical dispersion, and 1.8 kHz active crossover. The LF section includes a 12\\" driver with 2.5\\" copper voice coil and ferrite magnet; the HF section uses a 1.4\\" exit compression driver. The amplifier is a 1700 W two-channel Class-H with M1 power factor crossover, 24-bit DSP, 3-stage system protection, onboard 2-channel mixer with Bluetooth, TRS/XLR inputs and outputs, and a 16 A PowerCon input.Required 2 × 6/16 power points to be provided by the electrical contractor on the client’s side.Approved Make: British acoustics/ Meyer sound/Martin audio/d&b audiotechnik. |
| 9 | Supply, installation, testing, and commissioning of 2×1500 W Class H amplifier. Each amplifier has 2 output channels delivering 900 W per channel at 8 Ω, 1500 W at 4 Ω, 1800 W at 2.7 Ω and 2 Ω, with bridged outputs of 2700 W at 8 Ω and 3600 W at 4 Ω. The units feature 2 analogue inputs, 2 link outputs, and 2 power outputs. Connections are provided via XLR for signal input and link output, and Speak-On plus binding post connectors for channel outputs, ensuring reliable, high-power audio performance. Approved Make: British acoustics/ Meyer sound/Martin audio/d&b audiotechnik. |
| 10 | Supply, installation, testing, and commissioning of 2×2600 W Class H amplifier. Each unit provides 2 output channels rated at 1500 W per channel at 8 Ω, 2600 W at 4 Ω, 2800 W at 2.7 Ω, and 3000 W at 2 Ω, with bridged output capacity of 4500 W at 8 Ω and 6000 W at 4 Ω. The amplifier features 2 analogue inputs, 2 link outputs, and 2 power outputs. Connections are made via XLR connectors for signal input and link output, and Speak-On plus binding post connectors for channel outputs, delivering high-efficiency, professional-grade amplification. Approved Make: British acoustics/ Meyer sound/Martin audio/d&b audiotechnik. |
| 11 | Supply, installation, testing, and commissioning of 2×750 W Class H amplifiers. Each amplifier has 2 output channels delivering 450 W per channel at 8 Ω, 750 W at 4 Ω, 1000 W at 2.7 Ω, 1200 W at 2 Ω, with bridged outputs of 1400 W at 8 Ω and 1800 W at 4 Ω.The amplifiers feature 2 analogue inputs, 2 link outputs, and 2 power outputs. Connections include XLR for signal input and link output, plus Speak-On and binding post connectors for channel outputs, ensuring reliable high-power performance. Approved Make: British acoustics/Martin audio/d&b audiotechnik. |
| 12 | Supply, Installation, Testing & Commissioning of 4-IN 8-OUT Loudspeaker Processor, Matrix & Controller with 4 analogue inputs, 8 analogue outputs, and 96 kHz DSP on all channels. Audio performance: impedance >10 kΩ, CMRR >60 dB, min. load 600 Ω, frequency response 10 Hz–40 kHz, dynamic range >116 dB, THD <0.004%. Crossovers: Linkwitz-Riley, Bessel, Butterworth (12/24/36/48 dB/oct). EQ: 6 filters per input/output (parametric, low/high-shelf, all-pass), plus 2 dynamic EQ filters per input with adjustable threshold, ratio, attack/release. Dynamics include visual compressor, automatic gate compensation, and output limiters. Control & monitoring via 4 input/8 output meters, LED display, DSP control panel. Connectors: 4 XLR inputs, 8 XLR outputs, RS-485 (ETH/Euroblock), USB Type-B. Power: 85–230 VAC, 50/60 Hz; nominal consumption 1 A @ 240 V, 2 A @ 120 V. Approved Make: British acoustics/ Meyer sound/Martin/d&b audiotechnik. |
| 13 | Supply, Installation, Testing & Commissioning of 20-Channel Analogue Mixing Desk with Dual FX featuring 16 mic/line XLR inputs, 2 stereo line TRS inputs, USB audio playback/recording, and wireless media input. Outputs include stereo L/R, 4 group, 3 aux, and phones output. The desk has an 8-bus mixer: stereo L/R, 4 groups, and 3 auxes. Input strips provide dedicated metering, +48V phantom power, 20 dB pad, 3-band EQ, aux/FX sends, L/R panning, peak/solo PFL, and group selection. FX & features include Class-A PSL preamps, Oliver FX engine with preset library, individual return channels for FX1 & FX2, iPhone/Android/PC/Mac sound card compatibility, and 7-band stereo graphic EQ. THD+N: 0.03% (mic input to L/R at 30 dB gain), 0.015% (mic input to L/R at 0 dB gain), 0.04% (line input to L/R at 30 dB gain); input CMRR >60 dB.Approved Make: British acoustics/ Digico/ Wave / Yamaha / Midas /allen-heath. |
| 14 | Supply, Installation, Testing & Commissioning of an 18\\" Gooseneck Microphone with Base below specifications:-Type: Electret Condenser, Polar Pattern: Supercardioid, Freq. Response: 20-17 kHz, Max SPL: 140 dB, Working Volatge: 48V DC Phantom Power. Approved Makes: Clearone /OSL/Shure / Sennheiser. |
| 15 | Supply, Installation, Testing & Commissioning of Wireless Handheld Microphone Transmitter with Receiver: The wireless handheld microphone shall feature a display on the transmitter, be of dynamic type, and have an RF power output of 30 mW. The microphone shall use a cardioid polar pattern, provide a frequency response of 55 Hz to 20 kHz, and include a mute button on the transmitter. It shall operate on rechargeable batteries with 8 hours of operation, offer a wireless range of 100 meters, and use PLL synthesized circuits for frequency stability.Approved Makes: Clearone/OSL/Shure / Sennheiser. |
| 16 | Supply, Installation, Testing & Commissioning of Wireless Lapel and Headworn Transmitter: The wireless lapel and headworn microphone shall have an RF power output of 30 mW, frequency response of 20 Hz to 20 kHz, and include volume and mute controls on the transmitter. It shall operate on rechargeable batteries with 8 hours of operation, provide a wireless range of 100 meters, and use PLL synthesized circuits for stable frequency transmission.Approved Makes: Clearone/OSL/Shure / Sennheiser. |
| 17 | Supply, Installation, Testing & Commissioning of Vocal Wired Microphone: The vocal wired microphone shall be of dynamic type with a cardioid polar pattern, frequency response of 8 Hz to 18 kHz, and maximum SPL of 150 dB. It shall feature an all-metal housing, mute switch, foam protector to reduce wind and pop noise, and include an anti-glide microphone holder.Approved Makes: Clearone /OSL/Shure / Sennheiser. |
| 18 | Supply, Installation, Testing & Commissioning of Instrument Condenser Microphone: The instrument condenser microphone shall be of hybrid condenser type with a cardioid polar pattern, frequency response of 80 Hz to 18 kHz, and maximum SPL of 129 dB. It shall feature an all-metal housing and a mute switch.Approved Makes: Clearone /OSL/Shure / Sennheiser. |
| 19 | Supply, Installation, Testing & Commissioning of Light weight tripod alluminium Microphone stand with Long Arm, boom type & black anodized finish. Approved Makes: - My stand/ Amp Luxe /Netmas. |
| 20 | Supply, Installation, Testing & Commissioning of Light weight tripod alluminium Microphone stand with Short Arm, boom type & black anodized finish. Approved Makes: - My stand/ Amp Luxe /Netmas. |
| 21 | Supply, Installation, Testing and Commissioning of Customized Floor Box with 4x Mic In, 1x Speaker Out. Approved Makes: - My stand/ Amp Luxe /Netmas. |
| 22 | Supply, Installation, Testing and Commissioning of Customized Floor Box with 2x Mic In, Approved Makes: - My stand/ Amp Luxe /Netmas. |
| 23 | Supply, Installation, Testing and commissioning of a Digital Podium. The podium is to include essential features such as a 21” Finger-touch Monitor with Motorised Angle Adjustment, RFID Locks for security, a Controller facilitating Projector On/Off and Motorised Screen Up/Down operations, and a Switcher enabling seamless transitions between PC, Laptop, and Visualizer inputs for screen output. Additionally, the podium should incorporate a USB Port for Pen Drive connectivity, a Power Plug for Laptop compatibility, and an Audio system comprising 1 x Gooseneck Microphone. The tender also encompasses the provision of complete accessories necessary for installation and operation.Approved Make:- AmpLuxe/Netmas/AHA. |
| 24 | Supply, Installation, Testing & Commissioning of Mini PC with Intel Core i7 processor, minimum 16GB RAM, 512GB SSD, dual display support, Gigabit Ethernet, Wi-Fi, Bluetooth, Windows 11 Professional, complete with accessories.Approved Make :- Dell/HP/ Lenovo. |
| 25 | Supply, Installation, Testing & Commissioning of Wallplate Transmitter over Cat 6( HDBaseT) upto 70 meter with Inputs 1 HDMI, 1 USB-C & 1 Cat6 (HDBaseT) Output, 2K and 4K support, HDCP 1.4 & 2.3 both Compliant, Up to 60W USB–C charging on USB-C input, PoE acceptor, stereo audio output, 1 RS-232 for device control & 1 RS232 for serial link extension over HDBaseT output, Safety Regularity Compliance : CE, RoHs and WEEE, ISO 9001, ISO 14001, ISO 27001:2013 etc complete as required.Approved Make:- RGB Spectrum/Kramer/ Lightware. |
| 26 | Supply, Installation, Testing & Commissioning of HDMI Receiver over Cat 6 ( HDBaseT) up to 70m with Input 1 Cat6 (HDBaseT), 1 HDMI Output, 1080p, 2K and 4K@60 4:4:4, HDCP 2.2 Compliant, with IR and RS-232, Compliance : CE, etc complete as required. Approved Make:- RGB Spectrum/Kramer/ Lightware. |
| 27 | Supply, Installation, Testing and Commissioning of Speaker Cable – 2.5 Sqmm (80/0.20mm) x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath.Approved Make:- Draka/Belden/Netmas. |
| 28 | Supply, Installation, Testing and Commissioning of 18 AWG microphone cable (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC.Approved Make:- Draka/Belden/Netmas. |
| 29 | Supply, Installation, Testing and Commissioning of 8 Pair Snake Microphone Cable. Approved Make:- Draka/Belden/Netmas. |
| 30 | Supply, Installation, Testing and Commissioning of 1.8 Metres 4K HDMI patch cord in existing conduit. Approved Make:- RGB Spectrum/ Kramer/ Lightware. |
| 31 | Supply, Installation, Testing and Commissioning of HDBaseT certified 23 AWG shielded CAT6A Cable, Low smoke & Halogen Free, Delay Skew: <45ns, Propagation Velocity (NVP): 76%, Operation Temperature: –20˚C to +60˚CCOMPLIANCE - Electrical: EIA/TIA 568A, ISO/IEC 11801, Fire Performance: IEC 60332 1, Smoke Density: IEC 61034, Halogen Free: IEC 60754, RoHS: 2011/65/EU, Reaction to Fire Classification: Dca–s2,d1,a1 (optional: B2ca–s1,d1,a1),etc in existing conduit. Approved Make:- Extron/ Kramer/ Lightware |
| 32 | Supply and Laying of Crimp–style shielded RJ45 connector designed to fit larger 23AWG cables, overall insulation diameter of 1.40mm to 1.50mm, etc. Approved Make:- Extron/ Kramer/ Lightware. |
| 33 | Supply, Installation, Testing and Commissioning of for Auditorium, bulk connectors such as XLR (Male & female), RJ-45, Speakon, Phono, Stereo Jack, velcro tape, cable ties etc as per site requirement.Approved Make:- Neutrik / Amphenol / Netmas. |
| 34 | Supply, Installation,Testing & Commissioning of 27U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required.Approved Make: Valrack/Chief/Middle Atlantica/Netmas. |
| 35 | Part-A Civil Work |
| 36 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared |
| 37 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 38 | Earth filling with available surplus soil excavated from foundations and taken only from outside of building plinth in layers not exceeding 20cm in depth, consolidating each deposited layer including ramming and watering and consolidation with lead up to 50 mand lift upto 1.5 m. |
| 39 | Diluting and injection Chloropyrifos Emulsifiable concentrate 20%with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which approach is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion). |
| 40 | Supplying Chlorpyriphos/ Lindane emulsifiable concentrate of 20% in sealed containers including delivery as specified. |
| 41 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 42 | Random rubble stone masonry work in cement mortar with mechanical mixer in foundation (at any level) complete as per drawing and technical specification and as per clause 1000 and 1400 of MoRT&H specification including all scaffolding material, labour, machinery but excluding pointing and plastering. In cement mortar 1:4 (1 cement : 4 coarse sand) |
| 43 | Random rubble dry stone Kharanja (soling) under floor. |
| 44 | Supplying and Filling in plinth with river sand under floors including watering ramming consolidating and dressing complete including cost of sand |
| 45 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 46 | Centring and shuttering with plywood or steel sheet upto two stories ( each story of height upto 3.5 metre from floor level) including strutting, proppinFoundations, footings, bases of columns, etc. for mass concrete.g etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete. |
| 47 | Centring and shuttering with plywood or steel sheet upto two stories ( each story of height upto 3.5 metre from floor level) including strutting, proppinFoundations, footings, bases of columns, etc. for mass concrete.g etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 48 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786). Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 49 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix |
| 50 | Add extra for providing richer mixes respectively at all floor levels. Providing M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix. |
| 51 | Fine grinded Gangsaw cut 30-35 mm thick stone flooring over 20 mm (average) thick base of cement mortar 1:4 (1 cement :4 coarse sand) jointed grey cement slurry mixed with pigment to match the shade of stone complete as per design drawing and instruction of EI. |
| 52 | Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar |
| 53 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for , Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. |
| 54 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for , columns, pillars piers abutments posts and struts. |
| 55 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786). Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 56 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.M20 grade Nominal Mix / Design Mix |
| 57 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Arches, arch ribs, domes, vaults, shells, folded plate, chimneys, shafts , roofs having slope more than 15º ,vertical and horizontal fins individually or forming box louvers, facias and eaves boards M20 grade Nominal Mix / Design Mix |
| 58 | Add extra for providing richer mixes respectively at all floor levels. Providing M-25 grade concrete by using min 410 kg of cement per cum instead of M-20 grade design mix. |
| 59 | Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 insuperstructure above plinth level upto floor V level in. Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 60 | Half Brick work with mechanised autoclaved flyash lime bricksconforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 61 | P & F 1st quality Heavy Duty Vitrified glazed MAT tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete. size 600 mm X 1200mm |
| 62 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Jhunjhunu / Jalore (Red / Chocolate Colour)Above 3601 Cm2 Slabs |
| 63 | Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite/Kota Stone Work Full Edge moulding |
| 64 | HALF Edge moulding |
| 65 | Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete |
| 66 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 67 | Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. |
| 68 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 69 | Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. |
| 70 | Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 71 | Door & Windows openable |
| 72 | Extra for shutters of sliding aluminium windows |
| 73 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. |
| 74 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Prelaminated particle board with decorative lamination on both sides. |
| 75 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) For fixed portion |
| 76 | With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) For fixed portion |
| 77 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge With stainless steel cover plate |
| 78 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 79 | Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 80 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formaldehyde resin in glue both sides including approved ISI marked Stainless Steel butt hinges fittings with necessary screws complete as per annexure 'A' : 35 mm thick . Decorative teak veneer One side |
| 81 | Providing and fixing fully panelled/partly panelled/ double leaf shutter frame for doors as per approved design and drawings with approved ordinary C.P./ oxidised steel fittings as per Annexure - 'A' and width of styles & top rails of 100mm and lock rails width of 150mm and bottom rails of 200mm width including teak wood beading of size 19mm x 12mm on both faces complete : 35 mm thick, Ivory coast wood grade I |
| 82 | Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails complete as per approved by engineer in charge. 0.8mm thick mica |
| 83 | Extra for providing other type of fittings as mention in annexure A ( as approved by EI) : Brass fittings (Ivory coast wood grade I AREA) |
| 84 | Extra for providing other type of fittings as mention in annexure A ( as approved by EI) : Stainless steel fittings |
| 85 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured) |
| 86 | Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) : Rectangular or square. |
| 87 | Extra for cutting rebate in flush door shutters for making double leaf shutter(Total area of the shutter to be measured). |
| 88 | Providing and fixing bright finished 100mm mortice lock with 6 levers without pair of handles for aluminium door with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. |
| 89 | Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 90 | Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer pain |
| 91 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge. |
| 92 | Pr nd fixing to existing door frames. 30mm thick factory made solid both side Pre laminated panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15x15mm top & bottom rails. M.S .frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC ‘C channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75 mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet shall be provided as gap insert for top rail & bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide PVC sheet bending on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacture’s specification & drawing.(For W.C.and bathroom door shutter). |
| 93 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. complete fine finish : Plaster on new surface on walls in cement sand mortar 1:4including racking of joints etc. complete fine finish :12mm thick.( Internal plastr) |
| 94 | Plaster on new surface on walls in cement sand mortar 1:6including racking of joint etc. complete fine finish :20mm thick (outer Plaster) |
| 95 | Making grooves as per design in plaster 10mm to 20mm wide. |
| 96 | Add or deduct for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 97 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 98 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: |
| 99 | Finishing walls with textured exterior paint of required shade as per approved colour complete as per manufacturers specifications including primer coat and protecting coat including scaffolding and safety provision New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm. Trowel Finish av. thickness 1500 to 2000 microns. |
| 100 | RollerFinish av. thickness 400 to 500 microns. (70% of external plaster) |
| 101 | Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade :Two or more coats on new work |
| 102 | Providing and fixing stainless steel railing made of Hollowtubes, channels, plates etc., including welding, grinding,buffing, polishing and making curvature (wherever required)and fitting the same with necessary stainless steel nuts andbolts complete, i/c fixing the railing with necessaryaccessories & stainless steel dash fasteners , stainless steelbolts etc., of required size, on the top of the floor or the side ofwaist slab with suitable arrangement as per approval ofEngineer-in-charge, (for payment purpose only weight ofstainless steel members shall be considered excluding fixingaccessories such as nuts, bolts, fasteners etc.). Grade 304 |
| 103 | Providing and fixing steel gate, grating , and grills made ofangles, tees, square bars, flats,or black pipe with holdfast andfittings complete as per design and drawing including cuttingwelding and fabrication with priming coat of red oxide |
| 104 | Providing and laying water proofing treatment in sunkenportion of WCs, bathroom etc., by applying cement slurrymixed with water proofing cement compound consisting ofapplying : (i) first layer of slurry of cement @ 0.488 kg/sqm mixed withwater proofing cement compound @0.253 kg//sqm .This layerwill be allowed to air cure for 4 hours. (ii) Second layer of slurry of cement @ 0.242 kg/sqm mixed withwater proofing cement compound @ 0.126 kg/sqm This layerwill be allowed to air cure for 4 hours followed by watercuring for 48 hours. The rates includes preparation of surfacetreatment & sealing of all joints ,corners, junction withpolymer mixed slurry. |
| 105 | Grading roof for water proofing treatment with water proffing compound, Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 106 | Neat cement punning |
| 107 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 108 | Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification . 50mm thick. |
| 109 | Rough Chisel dressed Sand stone 35 mm thick flooring of approved shade set over 20mm thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointing with cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects Red sand stone (Karauli stone) same as coping |
| 110 | Making khurras 450 x 450mm with average minimum thickness 50mm cement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and one coat of neat cement, rounding edges and making and finishing the out let complete. |
| 111 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) Ordinary cement without any pigment. |
| 112 | Steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete. |
| 113 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 0.80 mm thick with zinc coating not less than 275 gm/m2 |
| 114 | Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. 0.80mm thick with zinc coating not less than 275 |
| 115 | add amount for modular kitchen lump sump |
| 116 | ADD for ornamental work in masony, jali and painting etc. |
| 117 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 75mm thick with 20mm thick nominal size aggregate. |
| 118 | Supply & lying River-gravels of following sizes in recharge shaft, filter pit after screening & washing from kachha shift without deduction of voids. Size 9 to 12 mm |
| 119 | Supply & lying River-gravels of following sizes in recharge shaft, filter pit after screening & washing from kachha shift without deduction of voids. Size 3 to 5 mm |
| 120 | Supply & laying of clean, clear sharp river sand of size 1 to 2mm coarse, without deduction of voids. |
| 121 | Providing and fixing of Reinforced Ferro cement Drain cover designed for class \\"B\\" loading duly marked on cover with adequate steel reinforcement having thickness 50 mm to 75 mm anti- corrosive bitumen painted M.S. plate Rim and on M.S. lifting hooks admixture like plasticizer bond improving compound shrinkage resistance compound abrasion resistant complete as per approved design etc. for drain Opeining Size 1201 to 1500 mm Standard Drain Cover Size 1800mm x 600mm x 75mm |
| 122 | Supply of ERW M.S. black casing pipe ISI marked(IS:4270/1992) of grade Fe410 of following sizes at site of work. 200 mm Nominal bore of pipe |
| 123 | Construction of tu ball 100 mtr dub 200 mm dia |
| 124 | P & F Indian type white glazed vitreous china 1st qualityW.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 580x440mm. |
| 125 | P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or Strap including cutting and making good the wall and floor |
| 126 | P & F water closet Seat Covers with brass hingescomplete : Solid PVC (IS 2548 marked) grade-I White for EWC. |
| 127 | P & F Jet spray for water closet with C.P. Copper Tubeflange of approved make. |
| 128 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting andmaking good the walls and floors: Exposed on wa 15mm dia Nominal Bore ''B' Class |
| 129 | 25mm dia Nominal Bore ''B' Class |
| 130 | P & F G.I. Pipes (External Work) with G.I. fittings excludingunion (IS : 1239 Mark) including trenching & refilling earth etc. 15mm dia Nominal Bore ''B' Class |
| 131 | 25mm dia Nominal Bore ''B' Class |
| 132 | 32mm dia Nominal Bore ''B' Class |
| 133 | Supply & fixing G.I. Union ISI marked in G.I. pipe line asrequired complete in all respect of size : 15mm dia nominal bore |
| 134 | 25mm dia nominal bore |
| 135 | fittings ofapproved make as per direction of Engineer-in-charge Swan neck pillar cock 15 mm nominal size |
| 136 | Bib Cock with long thread 15 mm nominal size |
| 137 | Long body Bib Cock 15 mm nominal size |
| 138 | Concealed stop cock 15 mm nominal size |
| 139 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked) with 37 cmlong pipe nut |
| 140 | P & F Full-way Valve (IS:778 Mark) or wheel valve ofapproved make : Gun-metal 15mm nominal bore. |
| 141 | Gun-metal 25mm nominal bore. |
| 142 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & makinggood the wall : Size 550 mm x 400 mm dia for counter top |
| 143 | P & F 15 mm. Dia Connection Pipe of approved quality/make : PVC pipe with C.P. Brass nuts upto length,600mm |
| 144 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality/make 110 mm dia |
| 145 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approvedquality /make Nahni Trap with Jali 4” 100mm dia |
| 146 | Bend 87.5 Dg. 110mm dia |
| 147 | Single Tee 110mm dia |
| 148 | Coupler 110mm dia |
| 149 | Vent Cowel 100 mm |
| 150 | Pipe Clip 110mm dia |
| 151 | Construction of septic Tank in all types of soil with 40 Cm.thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-Size 400 x140x150 cm.Size 230 x110 x150 cm.(for 20 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 10mm ϕ @15 cm c/c bothways includingshuttering complete in all respect. |
| 152 | Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: Size 240 Cm. diaoutside & 240 Cm. depth. |
| 153 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size300 X 300 mm depth upto 0.5 M Cement cover withframe. |
| 154 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size450 x 450mm depth upto 0.5 M Cement cover with frame |
| 155 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal ofsurplus earth within 50 mtr. lead. Depth up to 0.5 M |
| 156 | Providing Laying & jointing glazed S.W. pipes grade `A` (IS;651 marked) of approved make with spun yarn & stiff mixture of cement mortar 1:1, excavation & refilling of earth in all types of soil upto 1.2m depth, S.W. fittings, includingtesting of joints etc, complete. 150 mm dia |
| 157 | Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) upto haunches of S.W. pipes including 150 mm thick bed concrete (Width W= Dia of pipe in Cm+ 30Cm.) concrete width to be reduced from width W at center of pipe to `0` at top of pipe. (Excluding cost of pipe)150mm dia S.W. pipe |
| 158 | P & F Flush Cock / Flush Valve (IS : 9758 Mark) forWC of approved quality make : CP Brass concealed 25mm nominal bore. |
| 159 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball (IS: 1703 mark) complete including cutting and making good thewall: PVC with PVC bend as per IS 7231 |
| 160 | P & F Soap Dish or Tray of approved quality/make C.P.brass heavy & superior quality |
| 161 | P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor : 1.0 mm thick stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make as per Engineer-in-charge with large waste coupling. Overall size22 x 18 x 7 inches, Bowl size 20x16x7 inches |
| 162 | P & F Towel Rail or Ring of approved quality/make: C.P.brass towel rail with brackets 600 x 20mm. |
| 163 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers.Size 600 x 450 mm x 4 mm thick |
| 164 | P & F Bath Shower of approved quality/make. C.P. brassof Heavy & superior quality 150mm. |
| 165 | Construction of Open Surface Drain with 112mm thick brick masonry in CM 1:4,110mm thick base concrete 1:5:10, 37mm thick M-15 grade C.C. flooring ,12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation & disposal of earth complete as perapproved design/drawing: 250mm drain,300mm Av. depth |
| 166 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible class 2 copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible class 2 copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988) accessories, Aluminum round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, makingconnections, testing etc. as required. Short point (up to 3 mtr.) |
| 167 | Medium point (up to 6 mtr.) |
| 168 | Long point (up to 10 mtr.) |
| 169 | Short point (up to 3 mtr.) |
| 170 | Medium point (up to 6 mtr.) |
| 171 | Long point (up to 10 mtr.) |
| 172 | Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible class 2 copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible class 2 copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 6 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, makingconnections, testing etc. as required. On board |
| 173 | Short point (up to 3 mtr.) |
| 174 | Medium point (up to 6 mtr.) |
| 175 | Long point (up to 10 mtr..) |
| 176 | S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including making jhiri in the wall,clamps at suitable spacing, covering conduit andmaking good the same as required. 20 mm |
| 177 | 25 mm |
| 178 | 32 mm |
| 179 | 40 mm |
| 180 | Supplying and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade. Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size,Ferrules,testing etc. as required. 1 x 1.5 sq.mm |
| 181 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 182 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 183 | 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. |
| 184 | 4 x 6.0 sq.mm |
| 185 | 4 x 10.0 sq.mm |
| 186 | 1 x 2.5 sq.mm |
| 187 | 1 x 4.0 sq.mm |
| 188 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanism , energy limiting of class 3 as per IEC, minimum phase termination capacity of 25 sq.mm., conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating, 10,000 upto 63 A, 5000 for 80 A & above rating includingmaking connections, testing etc. as required. Single pole MCB (With B / C curve tripping characteristics)6 A to 32 A rating |
| 189 | Double pole MCB (With B / C curve tripping characteristics)50/63 A rating |
| 190 | Triple pole MCB (With B / C curve tripping characteristics)50/63 A rating |
| 191 | Four pole MCB (With B / C curve tripping characteristics)50/63 A rating |
| 192 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door (Metal / Glazed / Acrylic) Distribution board with Metal end box made out from Galvanized steel / CRCA sheet, powder coated conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, complete with 100 amp. insulated copper bus bar/shorting link , brass neutral link with shrouds, brass earth link , door earthing arrangement, color coded interconnecting wire set of minimum 10.0 sqmm size and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including makingconnections, testing etc. as required. Metal door (single phase) IK-09 and IP-43 with Metal endbox12 Way |
| 193 | Metal door (Three phase) IK-09 and IP-43 with Metal endbox 6 Way (8 incomer + 18 Outgoing) |
| 194 | P&F metal clad / Polyamide industrial plug top & socket unit with pin and sleeve type contact on porcelain/ bakelite base in Recessed/surface mounting heavy duty Enclosure made out from Galvanized steel / CRCA sheet , powder coated conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. (without MCB) including making connections, testing etc.asrequired. 20 amp, (2P + E), 1 Module |
| 195 | Providing & Fixing of Recessed/surface mounting heavy duty Vertical TPN Distribution board with Metal end box with provision of incomer suitable for 3/4 pole MCCB and SP / TP MCB up to 63 Amps. as outgoing ,made out from Galvanized steel / CRCA sheet , powder coated conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. complete with insulated 125/160/200/250 Amp. copper bus bar, brass neutral bars with shrouds, brass earth bar , color coded interconnecting wire set of suitable rating and din bar, door earthing arrangement, masking sheet, making internal DB terminations with copper lugs, ferrules, detachable gland plate, including making connections,testing etc. as required. Double door IP-43 & IK-09 with Provision of IncomerMCCB 200/250 A Rating with metal End Box 6 Way |
| 196 | Supplying and fixing of power plug point with Modular accessories on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular16 amp. Switch (IS :3854) and 6/16 amp. socket outlet(IS:1293) making connection , testing , etc. as required. |
| 197 | (h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator only (CPRI type Test certificates for Temp. rise test, Short circuit test for 50 kA and IP test is to besubmitted) |
| 198 | Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of SMC / DMC type insulator, with short circuit withstand capacity of 31 MVA for 1 Sec. , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. Electrolytic grade Aluminium bus bar 6010 grade |
| 199 | Providing & Fixing of IS: 13875 & IEC :61326/IEC:62053-22 confirming LED Digital type (up to 500) V range Volt meter / Direct- Ammeter / CT opertated ammeter/ Frequency meter / KWH meter / Multi Function Meter / Power analyzer of class 1 accuracy of size 96mm x 96 mm including making connection by PVC insulated copper conductor with PVC sleeves / channel etc. as required. Three phase Ammeter with Inbuilt Selector Switch |
| 200 | Three phase Voltmeter with Inbuilt Selector Switch |
| 201 | Providing & Fixing of Current Transformer confirming IS 2705-I (1992) with secondary terminal and shorting Block , with all necessary support in existing panel including connection etc. as required Current transformer Ring Type Tape Wound/Resin Cast Wound Accuracy Cl, CT ratio and burden as specified. ISF<=5, Cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in existing panel including connectionetc. as required . Ring type tape wound CT C T Class 1, Ratio 200/5 to600/5, Burden 10 VA |
| 202 | Providing & Fixing of 110/220 V, unibody LED Indicating lamp IEC 60947 with integral circuit, IP 65 above panel & IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min.27 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV, Rated insulation resistance shall be 100M ohm at 500VDC including connection etc. as required. Red/yellow/Green colour |
| 203 | Providing & Fixing of self healing IP20 MPP type shunt capacitor (banks) conforming to IS:13340-41 / IEC :831-1&2 OR IEC : 60831-1& 2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( PSD ) and shall have dissipation factor less than 0.0025 at 50 Hz, Operating loss less than 0.30 Watt per KVAR. Min over current capacity 1.8 times rated current & peak inrush current min. 300 times of rated current, life expectancy greater than 100000hrs (temp class - 25 D) in 440 V including making connections, testing etc. as required. Heavy duty Three phase 440 V, 50 Hz cylindrical typecapacitor (Bank) |
| 204 | Providing & Fixing of microprocessor based 3 CT’s for all 3 phase sensing compensation power factor correction relay with Approx. Size 139 mm x 139 mm, Operating Voltage 415/440 V , IEC / EN 61000-6-(2&4) having 3 CT sensing, sensitivity up to 50 milli amp secondary current , self analyzing auto c/k setting according to targeted power factor setting, the relay shall have digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, High voltage, THD-I & THD-V insufficient compensation, communication interface with RS 485, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multi Built in MFM with PF Controller LCD Display, CT polarity auto correction % THD up to 30 harmonics level, step switching time 2 sec to 1800 sec. Lead & Lag parameters, metering facility and 3 no. Class- 0.5 Cast Resin CT for sensing the relay including making connection with 1.5 Sq.mm copper wire etc. as required.12 to 16 stage |
| 205 | Providing & Fixing of 440 Volt 3 pole capacitor (AC 6 B ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current as per IS/IEC 60947-4-1 : 2000, insulation voltage 1000V, impulse withstand voltage 8 KV,Din rail mounting type including making connections, testing etc. as required. suitable forfollowing capacity capacitor bank. up to 6 KVAR |
| 206 | 8.5 KVAR |
| 207 | 10 KVAR |
| 208 | 12.5 KVAR |
| 209 | SITC of 3 /4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings, conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation from 50 to 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 690V. provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle ( to be paid extra) , including making connections etc. as required. OEM shall have submit NABL / CPRI / ERDA/ Intertekaccrediated lab type test certificate. 4 pole MCCB With Thermal Magnetic release up to 100 Amp , 25 kA, adjustable O/L & Fixed S/C setting, |
| 210 | 125 Amp , 25 kA, adjustable O/L & Fixed S/C setting, |
| 211 | 160 Amp , 25 kA, adjustable O/L & Fixed S/C setting, |
| 212 | 200 Amp , 25 kA, adjustable O/L & Fixed S/C setting, |
| 213 | 250 Amp , 25 kA, adjustable O/L & adjustable S/C setting, |
| 214 | 400 Amp , 35 kA, adjustable O/L & adjustable S/C setting, |
| 215 | Providing & Laying XLPE insulated & P.V.C. sheathed Armoured Aluminium cable confirming to IS :7098 P - I of1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) includingtesting commissioning etc. as required of following size. 6.0 Sq. mm 4 core |
| 216 | 4 core |
| 217 | 3.5 core |
| 218 | 3.5 core |
| 219 | Supplying and making one end termination with Nickel plated heavy duty brass single compression gland (as per IS 12943-1990)) SIBG type consisting of Check Nut, Gland Body, Metal Washer(3 Nos.), Outer Seal Rubber Ring, Compression Nut, heavy duty aluminium lugs (as per IS 8309 -1993) duly crimped with crimping tool, PVC tape as per IS 8337-1976 of following size of PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100volt grade as required. 4 x 6.0 sq.mm |
| 220 | 4 x 10.0 sq.mm |
| 221 | 3.5 x 95.0 sq.mm |
| 222 | 3.5 x 400.0 sq.mm |
| 223 | P / L of Double wall corrugated HDPE pipe confirming to IS: 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of trench, CC Haunching, Back filling of Earth with compaction is to be Paid Extra). 110 mm |
| 224 | Plate Earthing as per IS:3043 with copper Earth plate of purity >95% of size 600mm x 600mm x 3.0mm by embodying 3 mtr. below the ground level with 20 mm dia.G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, Heavy duty weather proof poly-propylene earth inspection chamber as per requirement of IS/IEC 62305 and tested as per IEC 62561-5 with lockable Jam free lid suitable for safe working load 60 kN of round / square size 250 mm, and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less asrequired. |
| 225 | Supply & Laying following size earth strip in horizontal or vertical run in surface by means of Earth strip DMC Insulator including riveting/ soldering/ welding, Jointing shall be done by overlapping double the width of strip and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. asrequired. 20mm x 3mm copper strip |
| 226 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. 8 SWG tinnedcopper Wire |
| 227 | Providing & Fixing BLDC technology step regulator compatible ceiling fan, with aluminium body & aluminium blade, power factor not less then 0.9 , following service value (CMM/W) , with following air delivery , speed 350 RPM ( tolerance as per IS:374 2019 ) THD less then 10%, copper winding with class of Insulation 'F' complete with with secondary support safety cable ( steel rope), down rod up to 30 cm, cotter pin, shackle kit with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. 1400 mm sweep with Air delivery>/= 270 CMM and Service Value 7.70 |
| 228 | Providing & Fixing of modular type 100W Step Fan regulator duly ISI marked (IS 11037) with CM/L no. printed made out of unbreakable and fire retardant virgin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including making connections, testing etc as required. 5 step fan regulator 2Module |
| 229 | P & F 1.2 mm thick M.S. Recessed fan box and top lid screwed on Box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 150 mmlength extended on each side as required. |
| 230 | Providing & Fixing of 400 mm Sweep BLDC technology Oscillating type Wall mounting / Pedestal type fans with Three speed, ON and OFF position, Double Wall bearing with front and back 120 or more ribs guard; Three no. blades, noise level should be <= 75 dB, including fixing with anchor bolts, making connection testing etc. as required. ( With Remote ) Wall mounting type with Servicevalue 2.0 CMM /W, Min. Air Delivery 71 CMM |
| 231 | Providing & Fixing of of Double ball bearing, copper wounded capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core 1.5 Sq.mm copper conductor ,making connections, testing etc. as required. 300 mm sweepMinimum air delivery 1600 Cum / hour |
| 232 | SITC of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output only at CW (5700K to 6500K) , internal surge protection of 4.0 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K/6000°K/6500°K (As per ANSI Bin) as required.1170mm(+/-10%) LED batten with min. lumen output 2200 lm |
| 233 | SITC of IP-20 LED Recessed / Surface Mounted, Round / Square backlit & SMD Mid Power LED Downlight with power coated die-cast aluminum housing with UV Stabilized non yellowish Diffuser with BIS compliance 4.0 KV surge protected Isolated driver, with Short & Open circuit protection input 320VAC-48 hr protection, input 350VAC-2 hr protection), having efficiency > 85% . System Lumen efficacy of ≥ 110 lm / watt,at CW (5700K to 6500K), THD < 10 % , Pf.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K/ 5700°K/6000°K/6500°K (As per ANSI Bin) as required. Minimum lumen output 600 lm (lumen efficacy ≥ 100 lm /watt) |
| 234 | Minimum lumen output 1300 lm |
| 235 | Minimum lumen output 600 lm (lumen efficacy ≥ 100 lm /watt) |
| 236 | Minimum lumen output 1300 lm |
| 237 | Minimum lumen output 1950 lm |
| 238 | Providing & Fixing of IK08 IP-66 protected high power LED flood light system with single piece Pressure diecast aluminium housing, toughened glass with suitable lenses on LED / integrated lens diffuser to achieve various beam angles, of high power LED of 3 to 5 watt each . Integrated metal case potted driver as a unique BIS R number (as per IS 15885) having efficiency more than 85 % and in compliance to BIS certified and Trade mark certificate(Fitting & driver both have separate BIS R number). The System level Luminaire efficacy >=130 lm/ wt. LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC & Low Voltage cutoff @>=90V AC and Auto resetting Safety .Power Factor >0.95 , THD(I) <10% , LED driving output current <=750mA. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector , Surge Protection Min >=4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hours with 70% of Initial Lumens maintained, CRI>70 and CCT 5700K ±355K asrequired. High Power LED Flood Light Minimum lumen output 15600lm |
| 239 | Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing and secondary lens on each LED/ integrated lens diffuser without cover & should be High power LED of 3 to 5 watt each . The System efficacy >=135 lm/ wt and integrated metal case potted driver & has a unique BIS R number ( as per IS 15885) with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC & Low Voltage cutoff @>=90 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . LED driving output current <750mA. The luminaire shall be BIS certified (Fitting & driver both have separte BIS R number) and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phaseto phase protection of 440 V for 4 Hrs as required. LED Street Light fixture with Minimum lumen output 13500lm |
| 240 | Providing & Fixing of Street light bracket made out from following size of ' B ' class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with heavy duty pole clamp, Saddles suitable fastners etc. as required. 32 mmDia. |
| 241 | Providing & Fixing of IK08 IP65 / IP66 protected LED Up - Down Luminarie Wall / Surface mounting made of powder coated die cast alluminium housing with with UV stabalized PC diffuser. The System level Luminous efficacy ≥ 80 Lumen/W. COB LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained Light output in Cool white or Warm White Colour as per engineers choice. LED driving output current<750mA. as required. Minimum lumen output 800 lm Up-Down Luminary |
| 242 | Supply , Installation, Testing and Comissioning of IS:1475 marked self contained drinking water cooler with hermetically sealed compressor,non CFC refrigerent suitable for operation on 230V/1pH/50Hz AC supply,Full stainless steel (SS304)body (0.8 mm thick) and tank (0.5 mm thick) , stainless steel water tray,minimum two nos Brass Chrome plated faucets and suitable drainage system complete in all respect with required height MS fabricated and Painted Angle iron frame ( Cost of frame to be paid Extra )complete in all respect of the following capacity. cooling capacity 150 Ltr./Hr. and storagecapacity 150 Ltrs |
| 243 | ADD GST @ 18% on Electrical Works |
| 244 | Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down valve in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor). 3.0 TR(Cooling Capacity 11200 Watt) |
| 245 | Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down valve in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as ofOutdoor) 2.0 TR (Cooling capacity 7000 watt) |
| 246 | Supply, Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling & heating, having 100% hermetically sealed inverter type twin rotary/Scroll Compressor(s) with and minimum two compressors , above 14 HP modules, microprocessor based Controller, Side / top discharge type condensing unit(s), with R-410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The EER/COP (W/W) at 100% load with AHRI conditions shall not be less than 3.8 etc. complete as required. 6 HP to 8HP |
| 247 | Supply, installation, testing & commissioning of Group controller for monitoring the status and working condition of all indoor and outdoor units, The controller shall act as an advanced air conditioning management system to given complete control of VRV/VRF air conditioning equipment with Starting/stopping of air-conditioning as a zone or group of individual units. Temperature setting for each Indoor units of zone, Switching between temperature control modes, switching of the fan speed and direction of airflow, enabling/disabling of individual remote controller operation, Alarm code display in case of any problem. Itshall be able to control up to 64 number of Indoor units. |
| 248 | Supplying and installation of high-pressure grade required size OEM make copper connection Y or T Joints / refnet for liquid and suction line , complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning systemcomplete as required. |
| 249 | Supply, installation, testing and commissioning of interconnecting copper refrigerant piping of DHE Grade C12200- ASTM B68, B75, chemical composition of copper%- 99.0 Min and Phosphorus %- 0.015 to 0.040 . For Annealed copper tube :- Tensile strength = 210 Mpa wih elongation % = 40 Min . Ink Mark Brand Printing on Hard Tubes should be present. duly insulated with tubular elastomeric nitrile rubber FM/UL approved with high water vapor diffusion resistance and low thermal conductivity should be certified 'Class O' in Fire Propagation as per BS 476 Part 6 with 7 mil Glass Cloth and 3 coats of anti UV paint (on area which is exposed to weather) including chase cutting andfilling with mortar, Slotted channel supports mounted on 10 mm threaded rod at suitable spacing the exposed piping shall be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tapeof 3 mm thick complete as required of following sizes. 41.1 mm O.D., wall thinkness ≥ 1.4mm (insulation – 19 mmthick) |
| 250 | 38 mm O.D., wall thinkness ≥ 1.4mm (insulation – 19 mmthick) |
| 251 | 34.9 mm O.D., wall thinkness ≥ 1.4mm (insulation – 19 mmthick) |
| 252 | 28.6 mm O.D., wall thinkness ≥ 1.2mm (insulation – 19mm thick) |
| 253 | 25 mm O.D., wall thinkness ≥ 1.2mm (insulation – 19 mmthick) |
| 254 | 22.2 mm O.D., wall thinkness ≥ 1.0mm (insulation – 19 mmthick) |
| 255 | 19.1 mm O.D., wall thinkness ≥ 1.0mm (insulation – 13 mmthick) |
| 256 | 15.9 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mmthick) |
| 257 | 12.7 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mmthick) |
| 258 | Supplying and drawing flexible / stranded bare copper conductor, PVC / XLPE insulated, overall aluminium mylar tape shielded ATC drain wire and outer PVC sheathed industrial Instrumentation (shielded)cables voltage grade 300/500 V as per BS /EN 50288-7 in existing surface or recessed PVC/ MS conduit/casing capping / Cable tray / Open Duct making connections, testing etc. as required. OEM must ensure that the cable is tested for complaince, either through their in house laboratory accrediated by NABL or by any Govt. laboratory accrediated by NABL and the laboratory's scope of accrediation should cover the requirements and testing procedure as per IS:10810. UnArmoured 2 core x 1.5 Sq.mm |
| 259 | Providing & Fixing of IS : 4985 - 2000 Class -4 (10 Kgf / Sqcm) UPVC drain water piping with fittings (IS:7834 & 10Kgf/sqcm) like elbow, socket, Tee, solvent cement jointing, support with MS hanger on ceiling or recessed in wall with chasing & plastering with 6 mm thick closed cell elastomeric nitrile rubber insulation including leakage testing etc. as required of following Nominal sizes. 20mm |
| 260 | Making hole in stone masonary/ RCC wall/ RCC slab with core cutter for accomodating refrigerant pipe/ drain pipe/ MS pipe/ cables etc of following dia 100 mm dia perrunning inch length |
| 261 | Providing & Laying XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, sheath confirming to IS:5831 in existing RCC / Hume / Stoneware/ PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing commissioning etc. as required offollowing size. 1.5 Sq. mm 2 core |
| 262 | Supply, Fabricating & installing following sizes of Hot dipped Galvanized iron Ladder type cable tray ( Galvanized thickness not less then 50 microns) with rungs at span of 250mm including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling/wall withM.S. suspenders etc. as required.150mm x 50mm x 1.6mm |
| 263 | 300mm x 50mm x 1.6mm |
| 264 | 600mm x 50mm x 2.0mm |
| 265 | 450mm x 50mm x 2.0mm |
| 266 | Providing & Fixing of DLP PVC adaptable trunking system for cable management including finishing accessories like corners, tees, adjustable angles, junction etc. as required . The trunking system shall have adaptable system for modular type RJ 45 data socket/ wiring accessories/ power sockets and shall be covered with peal off plastic cover. OEM have to submit NABL accrediated /CPET lab test reports /EN 50085-2-1 complaince certificate. 100/105mmx 50mmq |
| 267 | (h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator only (CPRI type Test certificates for Temp. rise test, Short circuit test for 50 kA and IP test is to be submitted) |
| 268 | Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of SMC / DMC type insulator, with short circuit withstand capacity of 31 MVA for 1 Sec. , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. Electrolytic grade Aluminium busbar 6010 grade |
| 269 | 160 Amp , 25 kA, adjustable O/L & Fixed S/C setting, |
| 270 | 250 Amp , 25 kA, adjustable O/L & adjustable S/C setting, |
| 271 | 150.0 Sq. mm 3.5 core |
| 272 | 70.0 Sq. mm 3.5 core |
| 273 | Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamelpaint etc. as required complete in all respect. . |
| 274 | Plate Earthing as per IS:3043 with copper Earth plate of purity >95% of size 600mm x 600mm x 3.0mm by embodying 3 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, Heavy duty weather proof poly-propylene earth inspection chamber as per requirement of IS/IEC 62305 and tested as per IEC 62561-5 with lockable Jam free lid suitable for safe working load 60 kN of round / square size 250 mm, and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less asrequired. |
| 275 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. 8 SWG tinnedcopper Wire |
| 276 | ADD GST @ 18% on AIR CONDITIONING Works |
| 277 | 450 LPM with 35 mtr head |
| 278 | Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS 'C ' class (Heavy) pipes conforming to IS 3589 / 1239 part-I for hydrant and sprinkler applications including cutting, screwing, welding etc. & forged steel fittings like elbows, tees, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick walls and making good the same. complete with painting of one coat of Red Oxide and two or more coat of synthetic enamel paint of Signal red shade complete as required.(Pipe to be tested @ 10Kgf/Sqcm for 2 Hrs.) 80 mm dia |
| 279 | 100 mm dia |
| 280 | 150 mm dia |
| 281 | Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS 'C' class (Heavy) pipe conforming to IS 3589 / 1239 part-I for hydrant and sprinkler applications in Existing trench with cement concrete block as supports including cutting, welding etc & forged steel fittings like elbows, tees, tapers, reducer with cleaning,wrapping and coating of the pipe with 4 mm thick tar based polymaric corrosion protection tape including applying uniform coat of cold pipekot primer as per IS; 10221 for protection against corrosion complete in all respect. ( Pipe to be tested @ 10Kgf/Sqcm for 2 Hrs. & Excavation of Trench and refillingof trench to be paid extra). 100 mm dia |
| 282 | 150 mm dia |
| 283 | Supplying and fixing cylindrical air vessel of continuous welded construction fixed at riser top made of 250 mm dia, fabricated out of 8 mm thick MS sheet, 1200 mm in height with flanged connection, Provision for 25 mm dia drain valve,air release valve,safety valve pressure gauge as required accessories and painting with two coats of Red Oxide and two coat of post office red enamel paint including The tank installed on suitable vertical legs. The legs shall be provided with M.S. Angle of size 75 mm x 75 mm x 5 mm at the bottom. The legs shall be grouted in cement concrete foundation. as required. ( Air Release valve, Drain valve, PRV, Pressure Gauge shall be PaidExtra ). |
| 284 | Supplying and Fixing of PN 16 Flanged Y strainer fabricated out of cast iron body, SS 304 strainer with perforated screen with 3 mm. dia holes in existing MS / GI pipe complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets etc as required offollowing sizes. 150 mm dia |
| 285 | Supplying and Fixing of PN 16 Cast Iron Dual Plate Wafer Type Check Valve / Non return valve with SS / Bronze flap complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required offollowing sizes.80 mm dia |
| 286 | 100 mm dia |
| 287 | 150 mm dia |
| 288 | Supplying and Fixing of PN 16 Butterfly Valve (Wafer Type) with S.G Iron Disc and confirming to IS:13095 complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required offollowing sizes. 80 mm dia |
| 289 | 100 mm dia |
| 290 | 150 mm dia |
| 291 | Supplying and Fixing of PN 16 Brass/GM Ball valves with screwed end, SS Ball including teflon tape etc. as required. 25 mm dia. |
| 292 | Providing and Fixing of PN16 Resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.5 Kg/cm2 and test pressure 14 Kg/cm2 to provide relief from stresses at pipe including Matching Flange (Minimum 16 mm thick), nuts,bolts, washers, gaskets, etc as required of following Sizes. 100 mm Dia. x 150 mm OAL |
| 293 | 150 mm Dia. x 150 mm OAL |
| 294 | Providing & fixing Stainless Steel pressure gauge with dial of 150 mm dia size and range 0 to 20 kg/sq.cm with 3 / 8 \\" BSP bottom entry , Ball valve , SS Syphon tube all fittings etc, duly calibrated before installation in MKS and FPS units, Accuracy Level +/- 1% including Making Drilling inExisting MS Pipe Etc. as required. |
| 295 | Supplying and fixing of SS 304 Single / Double headed oblique pattern hydrant landing valve (internal/external) with 75 / 100 mm dia flanged inlet & 63 mm dia instantaneous type female outlet coupling with cast iron wheel complete with ABS cap and chain and all accessories as per IS:5290-93 (Type-A) in cluding matching flange (14 mm thick), nuts, bolts, washers,gaskets, etc as required.Single Headed with 75 mm Dia. Flanged Inlet |
| 296 | Supplying and fixing orifice plate made of 6 mm thick stainless steel with orifice of required size in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 kg/cm2 complete with rubber gasket, GI bolts, nuts, washers etc.as required. |
| 297 | Supplying and fixing of flexible hose made with 100% polyester, black EPDM internal rubber lining with External coat of synthetic elastomer (IS:636, type-A) 63 mm dia, 15 mtr. Long RRL hose pipe with instanteneous type 63 mm dia SS-304 male and female couplings (IS:903) duly bound and riveted to hose pipes with copper rivets and SSwire etc. as required. |
| 298 | Supplying & fixing SS-304 Short Branch Pipe conforming to IS: 903:93 fitted with 20mm (nominal internal diameter) bore nozzle, for projecting water in form of solid jet. The Branch pipe shall have 63mm Male Instantaneous Inlet, suitable for use with 63 mm size Fire fighting hoses. H.P.tested to 21 kgf/cm² for 2.5 minutes. |
| 299 | Supplying and fixing first -Aid Fire hose reel Drum wall mounted swinging type with MS construction powder painted in post office Red, conforming to IS 884-1985 with upto date amendments, complete with the following as required. (A) Rubber Hose (B)20 mm dia UL, FM Bronze/ SS nozzle with 5mm orifice (C)Drum and brackets for fixing the equipments on wall. (D) Connections from riser with 20/25 mm dia Brass/GM gate valves with screwed end and conforming to IS:778 Class-1 through Forged steelScrewed Union & M.S. pipe. Etc. as required. With 30 m x 20 mm High Pressure Braided Rubber Hose as per IS:5132 - 1969 and Bursting pressure min. 42Kg/sqcm |
| 300 | Supplying and fixing Inlet Breeching Connection of CI body with Gun Metal male instantaneous inlet couplings with Inbuilt NRV, Drainage Connection with 50 mm Brass gate valve complete with PVC blank cap and chain as required for 150mm dia Outlet with 1 no. Matching Flange (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc asrequired of following Ways. 2 Way |
| 301 | Supplying and fixing of 750 mm x 600 mm x 250 mm Outdoor application Fire Hose Cabinet made of 1.2 mm thick MS sheet duly powder coated in red color externally and white internally with 6 mm thick glazed doors with Expanded Metal 2 mm thick Jali including necessary locking arrangement suitable to accommodate 2 Nos 15 Mtr. Long RRL Hose and 1 No. branch pipe on Existing Wall / Angle Iron Frame as required. (Cost of MS structurefor mounting Frame is to be Paid Extra) |
| 302 | Supply & Fixing of Fire Man's Axe with carbon steel head & rubber moulde handle usable upto 20 KV and confirming toIS :926 with length approx 0.4 M & weight min. 1.0 Kg. |
| 303 | 2 - Loop Panel |
| 304 | SITC of EN 54 / VDS certified photoelectric Analog addressable Smoke detector with mounting base & LEDetc. as required. |
| 305 | SITC of EN 54 / VDS certified Addessable Manual Callpoint (MCP) with LED / FIRE Indication Etc. as required. |
| 306 | SITC of EN 54 / VDS certified Addressable sounder with strobe light, Loop powered from FACP with sound level 90dB and programmable from the panel etc. as required. |
| 307 | Supplying and drawing Fire Resistant flexible / stranded bare copper conductor, PVC / XLPE insulated, overall aluminium mylar tape shielded ATC drain wire and outer PVC sheathed industrial Instrumentation (shielded)cables voltage grade 300/500 V as per BS /EN 50288-7 in existing surface or recessed PVC/ MS conduit/casing capping / Cable tray / Open Duct making connections, testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for cables. 2 x 1.5Sq.mm Unarmoured With Outer Sheath in Red Color |
| 308 | Supply & Fixing of Water + AFFF 6% Mechanical Foam type Fire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 25 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab isto be submitted. Capacity - 9 Ltrs. |
| 309 | Supply & Fixing of CO2 type Fire Extinguisher conforming to IS:15683:2018, charged with CO2 gas (purity 99.7% conforming to IS 15222), Powder coated Internal & External Surface Manganese steel ISI marked as per IS 7285 cylinder body , Wheel type Forged brass release valve ISI Marked as per IS 3224 with Inbuilt safety release device ((Fusible plug and Rupture Disc Type), 1.0 Mtr. Metal wire braided hose having minimum bursting pressure of 140 Kgf/cm2, Horn with metallic thread connection, QR code for Product Traceability, including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted.Capacity 4.5 Kg. |
| 310 | Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type Fire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 28 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM /External NABL Accrediated Lab is to be submitted. 4 kg |
| 311 | Providing and fixing of Aluminium housing body self contained Rechargeable LED Emergency Light with required content and Size Approx. 300 mm x 180 mm, confirming to IS:9583 :1981with Ni-Mh / Ni - Cd Battery, 3 Hrs Back Up, Constant Current Charger, Input Voltage 230 V , 50 Hz including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc.complete in all respects required. Single sided signage |
| 312 | (h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator only (CPRI type Test certificates for Temp. rise test, Short circuit test for 50 kA and IP test is to besubmitted) |
| 313 | Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of SMC / DMC type insulator, with short circuit withstand capacity of 31 MVA for 1 Sec. , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. Electrolytic grade Aluminium busbar 6010 grade |
| 314 | Providing & Fixing of Current Transformer confirming IS 2705-I (1992) with secondary terminal and shorting Block , with all necessary support in existing panel including connection etc. as required Current transformer Ring Type Tape Wound/Resin Cast Wound Accuracy Cl, CT ratio and burden as specified. ISF<=5, Cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in existing panel including connection etc. as required . Ring type tape wound CT C T Class 1,Ratio up to 150/5, Burden 5 VA |
| 315 | Red/yellow/Green colour |
| 316 | Blue / white Colour |
| 317 | Providing & Fixing of AC operated heavy duty 230 /440 Volt power contactor confirming to IS/IEC 60947-4-1 : 2000 having provision of mechanical interlocking, auxilary contacts, Din rail mounting type including making connections, testing etc. as required. 4 pole Powercontactors with following AC 1 Rating 40 Amp |
| 318 | 4 pole MCCB With Thermal Magnetic release up to 100 Amp , 25 kA, adjustable O/L & Fixed S/C setting, |
| 319 | Providing & Laying XLPE insulated & P.V.C. sheathed Armoured Aluminium cable confirming to IS :7098 P - I of1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing commissioning etc. as required of following size.16.0 Sq. mm 4 core |
| 320 | Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamelpaint etc. as required complete in all respect. . |
| 321 | ADD GST @ 18% on FIRE FIGHTING Works |
| 322 | 200mm Dia |
| 323 | Development of tube well as per IS specification usingsuitable compressor to give sand free water for required yield of the gravel packed tube well. |
| 324 | 200 mm dia |
| 325 | S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 326 | SITC of Single Stage, water cooled, High Speed (2880 RPM), Horizontal, Centrifugal, Openwell Submersible pumps set pre filled with coolent water and fitted with mechanical seal. The motor body of single phase pump shall be of SS and rest of all shall be of cast iron. Shaft of three phase pump shall be of SS 410 grade. All casting parts should be cathod electro deposition (CED) coated. Motor winding shall be 100% copper wire material. Dynamically balanced rotating parts to ensure min. vibration etc. All labour for testing of submersible pumps set and supply of water to w ater mains, complete in all respect. 12.5 HP, 3-Ø, (19.5 -33) Mtr, (2150-1300) LPM |
| 327 | Add 18% GST |
| 328 | Providing & Laying XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing commissioning etc. as required of following size. 4.0 Sq.mm 3 core flat / Round |
| 329 | Providing & Laying XLPE insulated & P.V.C. sheathed Armoured Aluminium cable confirming to IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing commissioning etc. as required of following size16.0 Sq.mm, 4 core |
| 330 | Providing & lowering of G.I. Pipes, flange pipe includingrubber washer and nuts of 8 mm dia complete in all respectI.S.1239 Marked.50 mm dia |
| 331 | 80 mm dia |
| 332 | Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985. 200mm dia |
| 333 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal bore Horizontal 50mm dia |
| 334 | Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, Heavy duty weather proof poly-propylene earth inspection chamber as per requirement of IS/IEC 62305 and tested as per IEC 62561-5 with lockable Jam free lid suitable for safe working load 60 kN of round / square size 250 mm, and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required. |
| 335 | 200 mm Nominal bore of pipe |
| 336 | Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level. In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. Depth upto 3.0 m |
| 337 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Walls |
| 338 | Suplying and Fixing Ductile iron Man Hole Covers/storm water grating and gratingwith frame of various sizes weight and types and load bearing capacity as per EN -124 ,superior quality or equivalent, comlete as per Direction of Engineer In charge |
| 339 | Ladder ,pipe and other item etc. |
| 340 | Add for electric connections ls Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysNov 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender