Tender For Special Repair To Bldg No.T-09,At 226 Coy Asc Depot Area, Provn Of Toilet Facilitis, Provn Of 2 X Toilet Block Adjestant To Bldg No G-30 & G-40 At Cod, For Staff At Aoc Officers Mess, Provn Of Rain Protection Shed And Misc Work House No.P-
Tender Value
42.52 Lakhs
Estimated cost
Bid Submission
06 Nov 2026
19 days left
EMD
85040
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No.T-09,At 226 Coy Asc Depot Area, Provn Of Toilet Facilitis, Provn Of 2 X Toilet Block Adjestant To Bldg No G-30 & G-40 At Cod, For Staff At Aoc Officers Mess, Provn Of Rain Protection Shed And Misc Work House No.P-42 At Kirby Place Under Ge (North) Delhi Cantt-10.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantaling corrugated, semi corrugated AC sheeting etc any gauge, thickness, or similar pattern roof covering including ridges all as specified and directed. |
| 2 | S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of sky blue/ sea green colour having tensile strength of 550 MPa as in roof covering, fixed with self tapping screws/ J hooks if required complete all as specified and directed. |
| 3 | S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. |
| 4 | Taking down wooden roof trusses, coupled rafters or trussed beams etc,(above 4 m & upto 8 mtrs),complete all as specified |
| 5 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe -290 (Gde E-165) complete all as specified. |
| 6 | M&L preparation new steel Surfaces of any des-cription, over 10cm in width or girth, not otherwise described two coat synthetic enamel paint over a coat of red oxide primer all as directed and specified. |
| 7 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as sepcified and directed |
| 8 | S & F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre /intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section of 0.55mm thickness having kurled web of 50mm and flange of 26mm each lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete size of grid 605 x 605mm all as specified and directed |
| 9 | S&F Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, overGI grame strips with 10 mm gap in between and reinforced with rabbit wire mesh fixed to GI frame made out of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having philips head with under head cutter at 200mm center to centre including finishing the joints of face with specially formullated jointing compound and 48 mm wide fibre tape to provide seamless finish of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete as per manufacturer instruction. |
| 10 | M&L for machine cut kota stone slab flooring 18-20 mm thick over 20mm thick cement screed bed using cement mortar (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including Pre- polishing complete all as specified. |
| 11 | M & L for machine cut kota stone slab flooring 18 to 20mm thick as in riser of step, dado and skirting over and including 10mm thick 1:4 CM backing coat on vertical surface of wall with rubbing and mirror polishing finished complete all as specified and as directed. |
| 12 | M & L 25mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded aggregate) for levelling course in floors complete all as specified and directed. |
| 13 | Demolition of brick work or stone builder masonry, built in cement or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete. |
| 14 | M & L Brickwork with subclass 'B' Brick straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 15 | Ditto- item No.6 but except brick complete. |
| 16 | M&L half brick wall with sub class B bricks, straight or curved on plan exc 6 m mean radium built in CM 1:4 all as specified and as directed. |
| 17 | Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water, at any description with necessary scaffolding. etc complete all as specified and as directed. |
| 18 | M&L 15mm thick ready mix plaster (Make Ultratech readiplast/ Birla Aerocon RMP/ ACC Suraksha RMP) on brick work on concrete surface of wall (external surfaces) finished even and smooth all as specified and directed,all as specified and directed. |
| 19 | M&L for preparation of new plastered surfaces of wall and applying two coat of cement based paint over a coat of cement primer. |
| 20 | M&L for complete removal of existing treatment of wall including cornices etc. by washing, rubbing down and stopping holes, and applying two coats of cement base paint of approved shade complete all as specified and directed. |
| 21 | M&L 15mm thick ready mix plaster (Make Ultratech readiplast/ Birla Aerocon RMP/ ACC Suraksha RMP) on brick work on concrete surface of wall (internal surfaces) finished even all as specified and directed by GE. |
| 22 | M&L for Preparing new plastered surfaces of wall and applying two coats of oil bound distemper white or tinted over and including a coat of 1mm thick wall care putty on plastered surfaces preparatory to distempering complete. |
| 23 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each and removing from site, complete all as specified and directed. |
| 24 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm eachand n exc 4 sqm and removing from site,complete all as specified and directed. |
| 25 | S&F Factory Made double rebated extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made |
| 26 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)complete all as specified and directed. |
| 27 | S& F Floor door stopper of aluminium alloy body and tongue ,anodised ,with hard drawn steel spring ,fixed in floor overall length of cover plate 140mm |
| 28 | S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified . |
| 29 | S&F 150mm long stainless steel handles, cast type complete all as specified and directed. |
| 30 | S&F 300mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed. |
| 31 | S&F factory made pressed steel windows of standard size and section with double shutter i.e. glazed & wire gaugeed shutter including all fittings like MS hold fast, box hinges, Handles , MS Tower Bolts ,Stoppers, hinges, MS stay with long screw, MS spring latch, MS Guard Bar/ grill etc complete with glazing bars including one shop coat of zinc chrome primer complete all as specified and as directed.Note:- (i) Rate quoted shall be deemed to be including of all fittings fixtures.(ii) Glass, wire mesh and painting only shall be measured and paid separately under relvent items of Sch.(iii) The Drawings referd above are available in the office of Engr-in-Charge and can be refreed in the office working hours if required. |
| 32 | Description all as per Item No. 21 above but with glazing bars complete all as Specified. |
| 33 | Description all as per Item No. 21 steel ventilator top hung shutter including hinges, steel peg stay, fixing lugs etc complete with or without glazing bars incl taking down of old steel ventilators of any size complete all as Specified. |
| 34 | M&L for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as Specified. |
| 35 | Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for complete all as specified and as directed. |
| 36 | M&L cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair without using extra cement incl making joints at every 2.5m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight including necessary form work and complete all as specified. |
| 37 | M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in subase of floor, complete all as specified and directed. |
| 38 | M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of with pigment M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer throughvibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all specified and directed by Engr In charge. |
| 39 | S&F for factory made kerb stone of M-25 grade precast cement concrete/stone laid in position to the required line, level and curvature, jointed with cement mortor 1:3 including making the joint with or without grooves including making drainage opening where ever required complete as per direction.Note (i) Length of finished kerb edging shall be measured for payment (ii) precast CC kerb shall be approved by the Engineer-in-Charge). |
| 40 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earthor broken rubble mixed with earth around, in layers notexceeding 25 cm, |
| 41 | M&L for PCC 1:3:6 ,type C-2 using 40mm graded crushed stone aggregate as in sub base and mass conc.complete all as specified and as directed. |
| 42 | Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil for roads to required slope gradient, camber etc complete all as directed. |
| 43 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out and getting out in soft/loose soil complete all as specified and directed. |
| 44 | Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil. |
| 45 | Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point. |
| 46 | M&L PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation complete all as specified & directed. |
| 47 | M&L for RCC M-25 (20mm graded aggregate) as in foundations footings, plinth beams etc all as specified & directed. |
| 48 | M&L for RCC M-25 (20mm graded aggregate) as in columns, pillars etc all as specified & directed. |
| 49 | M&L for RCC M-25 (20mm graded aggregate) as in beams, lintels etc all as specified & directed. |
| 50 | M&L for RCC M-25 (20mm graded aggregate) as in chajjas etc all as specified & directed. |
| 51 | M&L for RCC M-25 (20mm graded aggregate) as in slab type Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like |
| 52 | S&F TMT bars upto 10mm dia and over, cut to length, bent to shape required,including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. |
| 53 | S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia. |
| 54 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter |
| 55 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions |
| 56 | Form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (horizontal or sloping). |
| 57 | M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintes,cantilevers, shelves including supports, overhangs, etc also splays beteen floors and beams finished rough surfaces of concrete complete all as specified. |
| 58 | Formwork to chajjas, chullah hoods, similar items including edges all as specified. |
| 59 | M & L form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide. |
| 60 | M & L hardcore of broken stone or boulders of gauge exc.63mm but n exc 100mm, deposited,spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface. |
| 61 | M&L 75 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base |
| 62 | M&L Glazed ceramic tiles 300x450x7mm thick, in vertical surfaces such as skirting & dados set and jointed in neat cement slurry and pointed in coloured cement to match including backing coat of 10mm thick CM 1:4 on brick masonry/concrete surfaces finished even to receive tiles complete all as specified and as directed. |
| 63 | M&L Non skid ceramic tiles (400x400x7mm thick) in floors set and jointed in neat cement slurry and painted with colour cement to match including Screed bed (or) bedding layer of mortar 15mm thick for laying floor finishes CM (1:6) complete all as specified and as directed. |
| 64 | M & L 75mm th PCC 1:3:6 type C-2 as in sub base, Floors, Paving, plinth protection, finished even and fair without using extra cement complete all as specified. |
| 65 | Supply, laying and fixing of 20mm outer dia of CPVC pipe SDR 11 and plain CPVC SDR 11 fittings on wall/ceiling or laying in floors complete including brass CPVC fittings (i.e elbow, Tee, MTA/MBTA,FTA/FBTA, Tank adaptor, Union, etc suitable for 15mm bore bath fittings). (Note- length of pipe with fittings to be measured for payment, no extra payment should be made for fittings). |
| 66 | Supply and laying of 25mm outer dia of CPVC pipe SDR 11 and plain CPVC SDR 11 fittings on wall/ceiling or laying in floors complete including brass CPVC fittings (i.e elbow, Tee, MTA/MBTA,FTA/FBTA, Tank adaptor, Union, etc). (Note- length of pipe with fittings to be measured for payment, no extra payment should be made for fittings). |
| 67 | S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes all as specified and directed. |
| 68 | S & F 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete. |
| 69 | S & F ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic wall, screwed for iron pipe and fixed for 25 mm bore size (Minimum weight 210gms), complete. |
| 70 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete. |
| 71 | S&F 150x100 mm Salt glazed stoneware gully traps, square or rounded mouthed type 'P' , with CI grating including jointing with solvent cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in bed all as specified and as directed. |
| 72 | Cutting into existing manholes for connecting 150mm dia of pipe to new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required. |
| 73 | S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, 75 mm bore PVC/CI drain/Rain water pipe complete.. |
| 74 | S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, 110 mm bore PVC/CI drain/Rain water pipe complete. |
| 75 | S&F PVC (SWR) bends any radius, 75 mm bore, complete. |
| 76 | S&F PVC (SWR) bends any radius, 110 mm bore, complete. |
| 77 | S&F PVC (SWR) vent cowl, 75 mm bore complete. |
| 78 | S&F looking mirror of size 600mmx450mm with 5 mm thick mirror of selected quality glass, mounted on plastic frame and fixed complete. |
| 79 | S & F Soap dish disc (oval) type, stainless steel chromium plated of approximate size 100 x 50 x 10 mm, complete. |
| 80 | S & F sheet Glass shelf assembly consisting of 5.5 mm thick sheet glass self 12 cm wide with chromium plated bracket guard and railing 60 cm long. |
| 81 | S&F in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate mix with WPC complete all as specified and as directed. |
| 82 | S & F Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete. |
| 83 | S & F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15 mm bore complete. |
| 84 | S & F Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15 mm bore complete. |
| 85 | S&F 10 litre capacity PVC low level flushing cistern with dual flush type‘ white’ with inlet, float valve including bracket with 32mm dia PVC waste/flush bend pipe appx 600 mm long complete. |
| 86 | S & F PVC connection 450mm long and15 mm dia with brass fly nut at both ends complete. |
| 87 | S&F vitreous chaina squatting pan Orissa pattern size 580x440 white with integral foot rests, trap etc (Excluding flushing cistern and flush pipe) complete all as specified and directed. |
| 88 | Supply and fix vitreous China wash hand basin (pedestal type) white of size 550X400mm excluding taps, waste chain and plug and porcelain stopper and waste pipe & waste coupling including all necessary fitting and fixtures complete all as specified |
| 89 | S&F vitreous china urinals half stall bowl, flat back large of size 420x395x635 mm white with grating and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement complete all as specified. |
| 90 | S&F in repair vitreous china urinal partition white of size 310 x 770mm complete all as specified and directed. |
| 91 | S & F in repair Brass chromium plated shower rose 12.5 mm size with swivel joints, wall flange complete. |
| 92 | Construction of Soakage wells of size 1.80 Mtr dia x3.00m depth excavation in any types of soil, foundation in PCC 1:3:6 walls of honeycomb masonry with brick work all as shown in drng No. CEDZ- 1124(R) sheet No. 1/1 dated 12.02.2003, top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slabs in M-25/SFRC covers, interconnecting pipes of RCC/DWC complete filled with brick bats including demolition of existing old soakage well of any size and refill the same up to the existing ground level complete all as as specified and directed complete all as directed. |
| 93 | Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysNov 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender