Tender For Special Repair To Bldg No T-24 In ‘E Zone, Special Repairs/Replacement In Bldg No T-112 Of Hq 3 Corps And Provn Of Temp Toilet Block Near Bldg No T-03 Of 3 Corps Omc At Rms
Tender Value
46 Lakhs
Estimated cost
Bid Submission
07 Nov 2026
20 days left
EMD
92000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Wokha → Nagaland
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No T-24 In ‘E Zone, Special Repairs/Replacement In Bldg No T-112 Of Hq 3 Corps And Provn Of Temp Toilet Block Near Bldg No T-03 Of 3 Corps Omc At Rms
BOQ
| Sl. No. | Item Description |
| 1 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm each, in floors laid over and including 15mm thick screed bed for laying floor finishes in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including dismantling of old floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and as directed. |
| 2 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm each, on vertical surfaces such as skirting, dado risers to steps over and including backing coat of 10 mm thick in cement mortar (1:4) , set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 3 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm each, in floors laid over and including 15mm thick screed bed for laying floor finishes in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including dismantling of old floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and as directed. |
| 4 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm each, in floors laid over and including 15mm thick screed bed for laying floor finishes in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed. |
| 5 | M&L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile laid over and including backing coat of 10 mm thick in cement mortar (1:4) including dismantling of old tiles including cement mortar bedding of any description and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 6 | M&L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile laid over and including backing coat of 10 mm thick in cement mortar (1:4) complete all as specified and as directed. |
| 7 | M&L for light shade/coloured Vitrified Ceramic tiles , (8-9) mm thick (square/ rectangular) polished,area of each tiles exc 0.36sqm but not exceeding 0.42 sqm each, laid in floors over and including 15mm thick screed bed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles including dismantling of old floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and as directed. |
| 8 | M&L for Granite (of any type) tiles 18-20mm thick as in platform machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with nosing laid over and including 10 mm thick screed bed in cement mortar (1:4) including dismantling of old tile from its positions and removing rubbish off the premises complete all as specified and as directed. |
| 9 | M&L for chequered cement concrete tiles of size not less than 300x300x25mm thick laid over and including 15mm thick screed bed for laying floor finishes in cement mortar (1:4) etc, set, jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and directed. |
| 10 | M&L for chequered cement concrete tiles of size not less than 300x300x25mm thick laid over and including 15mm thick screed bed for laying floor finishes in cement mortar (1:6) etc, set, jointed and pointed in neat cement slurry with grey cement and pigments including dismantling of old tiles including cement mortar bedding and removing rubbish off the premises complete all as specified and as directed. |
| 11 | S&F in repairs 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-painted self embossed, textured designer board E-Board Classic to be fixed GI grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mm duly suspended with 6 mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size and finally applying two coats of oil bound distemper complete all as specified and as directed. |
| 12 | S&F in repairs Pre-painted galvalume aluminum zinc coating GI based corrugated trapezoidal steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed. |
| 13 | S&F in repairs Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed. |
| 14 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated trapezoidal steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed. |
| 15 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed. |
| 16 | M&L for second class hardwood as in scantlings clean sawn timber fixed as in unframed work including dismantling of old one from its position complete all as specified and as directed. |
| 17 | Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters (without taking off shutter from the frame) from the frames complete all as specified and as directed. |
| 18 | Taking down chowkhat or frames exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and as directed. |
| 19 | Material & labour 2nd class hardwood plain, solid straight chowkhats and frames, wrought, framed rebated on the solid,rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. |
| 20 | S&F factory made 35 mm thick flush shutter, solid core construction, with particle board core and plywood face panels, commercial type on both side, fixed to chowkats complete all as specified and directed. |
| 21 | M&L for factory made 30mm thick 2nd class hard wood Glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) complete all as specified and directed. |
| 22 | S&F in repair mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 18mm, fixed with tinned tacks or galvanized wire staples complete all as specified and directed. Please Enable Macros to View BoQ information |
| 23 | S&F in repair mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 18mm, fixed with tinned tacks or galvanized wire staples complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysNov 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender