Tender For Construction Work Of Gate At 30.00 M Chaundi Road Of Residential Township Of Greater Bareilly Housing Scheme.
Tender Value
1.56 Crore
Estimated cost
Bid Submission
13 Nov 2026
25 days left
EMD
3.12 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bareilly → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Work Of Gate At 30.00 M Chaundi Road Of Residential Township Of Greater Bareilly Housing Scheme.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.D.S.R. Item No. 2.8.1 |
| 2 | Providing & laying cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)D.S.R. Item No. 4.1.8 |
| 3 | C.C. 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)D.S.R. Item No. 4.1.3 |
| 4 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) D.S.R. ITEM NO. 5.1.2 |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum (level 1 to lvl-5) D.S.R. Item No. 5.33.2.1 |
| 6 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, plascing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. D.S.R. Item No. 5.22.6 |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for footings/PB, rough finished surface of conc. D.S.R. Item No. 5.9.1 |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for columns, pillers, piesr, abutment , post and strutsD.S.R. Item No. 5.9.6 |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantileversD.S.R. Item No. 5.9.5 |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roof , landings, balconies, acessess platformD.S.R. Item No. 5.9.3 |
| 11 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) D.S.R. Item No. 4.10 |
| 12 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.D.S.R. Item No. 22.5 |
| 13 | Brick work with common burnt clay modular bricks of class designation 15 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)D.S.R. 2023 Item No. 6.2.1 |
| 14 | Brick work in SUPER STRUCTURE in 23 cm thk wall with 1:4 cement and coarse sand incl. all materials labour annd t&p etc. for proper completion of work.D.S.R. Item No. 6.4.1 |
| 15 | 12 mm thk plaster (1:4) with cement & Coarse Sand (Fair Face)D.S.R. Item No. 13.4.1 |
| 16 | Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. D.S.R. Item No. 13.80 |
| 17 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm(make:Asian/Berger/Dulux)D.S.R. Item No. 13.48.1 |
| 18 | Finishing walls with Acrylic Smooth exterior paint of required shade :-New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10sqm.).D.S.R. Item No. 13.46.1 |
| 19 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksD.S.R. Item No. 10.25.2 |
| 20 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new workD.S.R. 13.61.1 |
| 21 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:D.S.R. Item No. 10.2 |
| 22 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing balcony railing & staircase railing including applying a priming coat of approved steel primer.M.S. tube.D.S.R. Item No. 10.26.1 |
| 23 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self drilling tapping screws for joining the members shall have a Type II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT.The rate includes the concept design, detaileddesign, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above. 1.00 mm thick with zinc coating not lessthan 275 gm/m²D.S.R. Item No. 12.1.1 |
| 24 | Providing and fixing 3 mm thick Exterior Grade High Pressure Laminate (HPL) (Mikasa FX make) Cladding on external wall surfaces, fixed over aluminium supporting framework made out of aluminium sections of size 50 × 25 × 2 mm or approved equivalent, consisting of vertical and horizontal members, rigidly fixed to RCC / brick masonry with dash fasteners / chemical anchors of suitable size at required spacing.The HPL (Mikasa FX make) sheets shall be fixed with SS 304 grade screws / rivets, including drilling holes, cutting, groove making, edge finishing, providing EPDM rubber gasket / spacer tape, weather grade sealant in joints, including all necessary accessories, scaffolding, labour, tools & tackles etc., complete as per manufacturer’s specification and direction of Engineer-in-Charge.The HPL sheet shall be:Exterior grade compact laminateThickness : 6 mmDensity : ≥ 1350 kg/m³UV resistant decorative finishFire retardant gradeThe work shall include all materials, labour, fixing accessories, framework, fasteners, sealant and complete installation.Market Rate |
| 25 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. Thetiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed vitrified floor tiles polished finish of size 600x1200mmD.S.R. Item No. 11.41A.2.2(Make : Simpolo/RAK) |
| 26 | Antiskid tilesProviding and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08 and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size600 x 600 mm (Make : Simpolo/RAK)DSR 11.41A.3.1 |
| 27 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Make : Simpolo/RAK)DSR 8.31 |
| 28 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. Granite stone slab of colour black, Cherry/Ruby red D.S.R. Item No. 8.2.2.2 |
| 29 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. D.S.R. Item No . 8.5 |
| 30 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.DSR 9.76 |
| 31 | Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.DSR 9.77 |
| 32 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarsesand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase D.S.R 2021No 12.21.1 |
| 33 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. D.S.R. No.12.22.1 |
| 34 | Construction of granular sub base (G.S.B.) by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, compete at per clause 401. Note : Contractor will make arrangement before doing the work job mix formula will be prepaired and aproved by Govt./Semi Govt./ Instituition by ISO certified repoted lab. Job mix will be aproved by compitent authority of RDA. It will be applicable in R.C.C. work M20/M25 and GSB/WMM/DBM/BC. Bitumens and cement and other material will be used as per job mix, for this no extra pay will be done.(Analysis Rate) |
| 35 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. Note : Contractor will make arrangement before doing the work job mix formula will be prepaired and aproved by Govt./Semi Govt./ Instituition by ISO certified repoted lab. Job mix will be aproved by compitent authority of RDA. It will be applicable in R.C.C. work M20/M25 and GSB/WMM/DBM/BC. Bitumens and cement and other material will be used as per job mix, for this no extra pay will be done.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.D.S.R. 2023 Item No. 16.91.2 |
| 36 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).Note : Contractor will make arrangement before doing the work job mix formula will be prepaired and aproved by Govt./Semi Govt./ Instituition by ISO certified repoted lab. Job mix will be aproved by compitent authority of RDA. It will be applicable in R.C.C. work M20/M25 and GSB/WMM/DBM/BC. Bitumens and cement and other material will be used as per job mix, for this no extra pay will be done.D.S.R. Item No. 16.69 |
| 37 | Providing and laying in position specified grade of cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)D.S.R. Item No. 5.1.3 |
| 38 | Providing and fixing laser cut Acrylic Backlit letters (Acrylic Font) With LED backlit illumination made from approved quality cast acrylic sheet of required thickness (minimum 3–5 mm or as specified) for signage/branding work, including cutting as per approved design, polishing of edges, drilling holes, and fixing on wall surface with SS studs, spacer, adhesive or suitable fixing arrangement, complete in all respects including alignment, finishing, and cleaning as directed by Engineer-in-Charge.The rate shall include all materials, labour, tools, scaffolding, transportation, wastage, and installation complete as per approved drawing and site requirements.Market Rate |
| 39 | Providing and fixing Bareilly Development Authority Logo with LED backlit illumination made of approved material including fabrication, LED modules, driver, wiring and fixing complete as per approved design and direction of Engineer-in-Charge.Size: 1000x1000mmMarket Rate |
| 40 | Providing and fixing factory made uPVC white colour sliding glazed door/window comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainlesssteel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. (Make : Fenesta)Two track four panels sliding door made of (big series) frame67 x 50 mm & sash 46 x 82 mm both having wall thicknessof 2.3 ± 0.2 mm and single glazing bead / double glazingbead of appropriate dimension. (Area of door above 8.00sqm upto 10.00 sqm). sqm D.S.R. Item No. 9.147.A2.2 |
| 41 | Float glass panes of nominal thickness 6 mm (weight not less than 20.00 kg/sqm)(Make : as provided by Fenesta)DSR 2618 |
| 42 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: DSR 22.7.1(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofingcompound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofingcompound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 andapproved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm.D.S.R. 22.7.1 |
| 43 | Providing and laying Vitrified tiles (Heavy Duty) in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, Parking laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). on external area(Make : Simpolo/RAK)Size of Tile 500x500 mm D.S.R. Item No.11.47.1 |
| 44 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white plastic seat and lidMake: JaquarD.S.R. Item No. 17.2.1 |
| 45 | Providing & fixing chrome plated brass battery based infrared sensoroperated pillar cock, having foam flow technology.15 mm nominal boreD.S.R. Item No. 18.84.1 |
| 46 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Semi rigid pipe : 32mm diaMake : Finolex/AstralD.S.R. Item No. 17.28.1 |
| 47 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. D.S.R. Item No. 17.31.1 |
| 48 | Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge.15mm nominal boreMake : JaquarD.S.R. Item No. 17.16A |
| 49 | Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms.Make: JaquarD.S.R. Item No. 17.71 |
| 50 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes.110mm diameterMake : Finolex/AstralD.S.R. Item No. 12.41.2 |
| 51 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110mm Make : Finolex/AstralD.S.R. Item No. 12.43.2 |
| 52 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.Make : Finolex/AstralD.S.R. Item No. 12.44 |
| 53 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20mm dia nominal outer dia pipesMake : Finolex/AstralD.S.R. Item No. 18.7.2 |
| 54 | 25mm dia nominal outer dia pipesD.S.R. Item No. 18.7.3 |
| 55 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.15mm dia nominal outer dia pipesMake : Finolex/AstralD.S.R. Item No. 18.8.1 |
| 56 | 20mm dia nominal outer dia pipesD.S.R. Item No. 18.8.2 |
| 57 | 25mm dia nominal outer dia pipesD.S.R. Item No. 18.8.3 |
| 58 | Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions15mm nominal bore.D.S.R. Item No.18.21.2.1 |
| 59 | Providing & fixing CP brass bib cock of approved quality conforming to IS 893115mm nominal boreMake : JaquarD.S.R. Item No. 18.49.1 |
| 60 | Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal boreMake : JaquarD.S.R. Item No. 18.53.1 |
| 61 | Providing and fixing gun metal gate valve with wheel of approved quality.25mm dia nominal boreMake : JaquarD.S.R. Item No. 18.17.1 |
| 62 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25 mm nominal bore Make : Jaquar D.S.R. Item No. 18.18.3 |
| 63 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank. IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Make : Finolex/AstralD.S.R. Item No. 18.48 |
| 64 | ELECTRICAL WORKSWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. Make:Schneider/RR Kabel/Northwest DSR ELECTRICAL 2025 ITEM NO. 1.8.1 (Group A) |
| 65 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2X 1.5sq. mm + 1 X 1.5 sq. mm earth wireMake: Polycab/RR Kable/HavellsDSR 2025 (E/M) Item No. 1.14.1 |
| 66 | 2X4 sq. mm + 1 X 4 sq. mm earth wire Make: Polycab/RR Kable/HavellsDSR 2025 (E/M) Item No. 1.14.3 |
| 67 | 2X 6 sq. mm + 1 X 6 sq. mm earth wireMake: Polycab/RR Kable/HavellsDSR 2025 (E/M) Item No. 1.14.4 |
| 68 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.Make: Polycab/RR Kable/HavellsDSR 2025 (E/M) Item No. 1.21.1 20 mm |
| 69 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.Make: Polycab/RR Kable/HavellsDSR 2025 (E/M) Item No. 1.21.2 25 mm |
| 70 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.make: Polycab/RR Kable/HavellsDSR 2025 (E/M) Item No. 1.21.3 32 mm |
| 71 | SUBHEAD III-DISTRIBUTION BOARDSupplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator) Make:Schneider/RR Kabel/Northwest 8 way , Double doorDSR 2025 (E/M) 2.3.2 |
| 72 | 12 Way Double doorDSR 2025 (E/M) 2.3.3 |
| 73 | Supply and fixing of 6Amp to 32 Amp (10 KA)SP MCB in existing MCB, DB complete with connections as required. (CAT: A) make:Schneider/RR Kabel/Northwest DSR 2025 2.10.1 |
| 74 | Supplying and fixing following rating, four pole, 415 V, isolator in theexisting MCB DB complete with connections, testing andcommissioning etc. as required.63 Amp.DSR 2025 (E/M) 2.13.2 |
| 75 | 40 Amp.DSR 2025 (E/M) 2.13.1 |
| 76 | Supplying and fixing single pole blanking plate in the existing MCBDB complete etc. as required. make:Schneider/RR Kabel/Northwest DSR 2025 (E/M) 2.11 |
| 77 | SUBHEAD IV-EARTHING Earthing with copper earth plate 600 mm X 600 mm X 3 mm thickincluding accessories, and providing masonry enclosure with coverplate having locking arrangement and watering pipe of 2.7 metrelong etc. with charcoal coke and salt as required.DSR 2025 (E/M) 5.6 |
| 78 | Supplying and Laying of 25 mm X 3 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mmDSR 2025 (E/M) 5.9 |
| 79 | Providing and laying earth connection from earth electrode with 6SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrodeincluding connection with G.I. thimble excavation and re-filling asrequired.DSR 2025 (E/M) 5.12 |
| 80 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Disect Current(BLDC) motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value(CM/M/W) minimum 6, Air delivery minimum 210 Cum/Min, 350 RPM(tolerance as per IS: 374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise= 75 degree C(max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.make: Bajaj/Havells/CromptonDSR 2025 9.1.3 |
| 81 | Supply & fixing of 7/9 W LED BULB complete in all respect. Make: Bajaj/Jaquar/Go Green |
| 82 | Supply and fixing of LED Tube Light with batten suitable for up to 1X20 watt LED tube light complete including tube etc. on surface complete in all respect.Make: Bajaj/Jaquar/Go Green |
| 83 | Supply of AC 230/250 Volts, 50 Hz 55w 1400 rpm exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required.-Make: Bajaj/Jaquar/Go Green300mm sweep. |
| 84 | Providing & fixing Wall Bracket Light 3 WattMake: Bajaj/Jaquar/Go GreenMake Bajaj |
| 85 | Providing & Fixing Wall Façade Light 3 WattMake: Bajaj/Jaquar/Go GreenMake Bajaj |
| 86 | SITC Of Round flood light, 24W, 1780 lumens pm 10 5 2, 30 deg beam (plus/minus 10)% 3000K ±150K Supply of exterior-rated architectural floor/wall/Pole mounted, IP66, round flood light complete with antiglare snoot. The power consumption should be not more than 24 watts, minimum system lumen delivered shall be 1780 lumens (plus/minus 10)% 30 deg beam angle (plus/minus 10)% CCT-3000K ±150K LED from Bajaj/Go Green/Jaquar. The housing material should be die-cast aluminum with Electrostatically applied polyester powder coating. The luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses and a clear tempered glass cover. Bracket shall have a locking mechanism to fix and secure the required tilting angle, plus/minus 90 deg It should have CRI>80, and SDCM≤4. The driver should be integrated AC with PF > 0.1 & and THD-20%, Leader cables, jumper cables, and IP68 connectors are included, minimum IK06. The operating temperature should be of - 40 deg * C to 50 deg * C range and the storage temperature shall be - 40 deg * C to 70 deg * C the weight of luminaire shall be min 1.8kg. The lifetime of the luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test Photometric data shall be passed on test results from an independent testing lab. All mounting accessories shall be stainless steel (Minimum-316) for all lighting fixtures. All hardwired connections to LED fixture shall be reverse-polarity protected and shall provide high-voltage protection in the event that connections are reversed or shorted during installation. The luminaire should be BIS-certified The luminaire manufacturer shall provide optical performance, polar diagram and photometric data in various formats including IES files in accordance with IES 79-08. This includes all the required hardware for the successful operation of the luminaire. All the technical parameters of the luminaire need approval from the lighting consultant. Including casing made of SS with five year O&M Complete in all Respect.Make : Bajaj/Go Green/ Jaquar as approved by Engineer in Charge.P.S. |
| 87 | SITC of 1000mm long RGBW (W=4000°K) LED Rigid Linear Uplighter with System wattage of maximum 15-watt, min lumen output of 700lm, 20x30 degree beam angle, complete with integrated power supply, suitable IP66connectors, luminaire controls via DMX512 with Auto addressing for easy configuration. The connectivity should be of a daisy chain topology, allowing easy installation to form long run lengths. The same shall include Installation clamps, 5core/cat-6 or suitable control cables UV and weatherproof, other required accessories & hardware. The luminaire shall be extruded Aluminium with Electrostatically applied polyester powder coating, silicon gasket and clear tempered glass, minimum dimension of 1000X25X35mm with bracketand minimum weight of 0.85kg. The Luminaire shall have tilting adjustability +15° to-90°. The LED luminaire shall have SDCM<4 for white, the life of Luminaire shall be 50000hrs L70B50 at 35deg C. The luminaire should be IP66 & IK-06. The operating temperature of Luminaire shall be -40°C to 50°C and storage shall be -40°C to 70°C. The product shall comply to and shall have test repots for IEC 60598-2-5:2015, IEC 60598-1:2014 + A1, IEC TR 62778:2014 (for LED chips), EN IEC 55015:2019+A11, EN 61547:2009, EN 61000-3-2:2019, EN 61000-3-3:2013, IS 10322 (Part 5/Sec5):2013, LM80. Manufacturere ealf declaration shall he unloaded along with the technical hid. Including casing made of SS with five year O&M Complete in all Respect.Make : Bajaj/Go Green/ Jaquar as approved by Engineer in Charge.P.S. |
| 88 | SITC of surface mounted, exterior-rated LED linearstrip light with 55W/5m 400 Im/m luminaire with all the necessary accesories as below that is designed for grazing architectural lighting applications waterproof and anti- dust LED strips. It shall be sealed with Glue-injected with polyurethane (PU). SDCM<5 and RGB. Robust Design & IP68 rating for outdoor use. Luminaire has input voltage 24VDC, Operating temperature -40°C to 50°C, IP68 & IK06 protection, Lumen maintenance of 30,000 hrs @ L50 at 35°C. Standards: EN60598, EN62471, EN62493+IEC62778, CE-EMC. Including casing made of SS with five year O&M Complete in all Respect.Make : Bajaj/Go Green/ Jaquar as approved by Engineer in Charge.P.S. |
| 89 | Supply, Installation and testing of electrical pannel having 63 Amp MССВ 2P with 5 outgoing of 16 amp MCB. Pannel with timmer & surge proctation device Including casing made of SS with five year O&M Complete in all Respect.Make : Schneider Electric, ABB, Legrand, as approved by Engineer in Charge.P.S. |
| 90 | Supply, Installation and testing of 3 Phase Servo Stablizer with minimum capicity of 30KVA, Oil cooled with 180-260 VAC Including casing made of SS with five year O&M Complete in all Respect. Make : Schneider Electric, ABB, Legrand,as approved by Engineer in Charge.P.S. |
| 91 | Supply and laying of 2.5 Sq mm 3 core PVC insulated unarmoured multistrand copper cable as per site requirement. Including casing made of SS with five year O&M Complete in all Respect.Make: Polycab/Finolex/RR Kabel as approved by Engineer in Charge.P.S. |
| 92 | Supply and laying of 6 Sq mm 5 core PVC insulated unarmoured copper cable as per site requirement Including casing made of SS with five year O&M Complete in all Respect.Make: Polycab/Finolex/RR Kabel as approved by Engineer in Charge.P.S. |
| 93 | Supply and laying of Armoured CAT 6 cable as per site requirement. Including casing made of SS with five year O&M Complete in all Respect.Make: Polycab/Finolex/RR Kabel as approved by Engineer in Charge.P.S. |
| 94 | Supply and Laying of PVC/HDPE pipe 32 MM as per site requirementP.S. |
| 95 | Supply and burgn 600x 600mm x 3mm copper plate vertically for earthing with its top at least 3 metres below ground level complete gat Rmm da G.1 pipe and funnel for watering and two earthing lead oftwo no. 8 SWG copper wire in 15mm dia G1 pipe up to switch rd (from appron to switch board the cost of G.1. pipe and copper wire will be extra) 30cm squareCT. trame with hinged coxer masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround ete.complete in all respect. (Pw Schedule 2018 item no 705) Including casing made ofSS with five year O&M Complete in all RespectP.S. |
| 96 | Supply and fixing IP 67 boxes with all accessories as per site requirementP.S. |
| 97 | Supply & plantation of Trees upto 8ft to 10ft height well settled, all indigenous varieties (local) as per listed below, location and quantities shall be as per drawingMangifera Indica (Mango), Bacopa Monnieri (Brahmi), Terminalia Tomentosa (Asna), Azadirachta Indica (Neem) & Bambusa Bambos (Baans), Terminalia Arjuna (Arjun), Tectoria Grandis (Sagaun), Shorea Robusta (Saal), Stereospermum Tetragonum (Padal), Anogeissus Latifolia (Bakli), Madhuca Longifolia (Mahua) & Diospyros Malabarica (Gaub), Saraca asoca (ashok), Ficus religiosa (peepal), Ficus benghalensis (bargad), Aegle marmelos (bel) & Phyllanthus emblica (aonla), Pterocarpus Santalinus (rakta chandan), Butea monosperma (dhaak), Artocarpus altilis (kathal) & Santalum album (chandan), Saraca Asoka (Sita Ashok), True Cinnamon (Nag Kesar), Mangolia Champaca (Champa) & Mimusops Elengi (Maulsari), Saussurea Ggossypiphora (Mratyusanjeevani), Azadirachta Indiac (Neem) & Adiantum Venustum (Hansraj) |
| 98 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).2.1 (dsr hort. 2025) |
| 99 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).2.2 (dsr hort. 2025) |
| 100 | Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% forpayment).2.3 (dsr hort. 2025) |
| 101 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) :2.4.1 (dsr hort. 2025) Screened through sieve of I.S. designation 20 mm |
| 102 | Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area. (two application) i/c cost of chemical) and as per direction of officer-in-charge.and as per directionof officer-in-charge.2.56 (dsr hort. 2025) |
| 103 | Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.2.33 (dsr hort. 2025) |
| 104 | Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) 2.13 (dsr hort. 2025) |
| 105 | Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment).2.25 (dsr hort. 2025) |
| 106 | Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. 4.88 (dsr hort. 2025) |
| 107 | Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge. 4.91 (dsr hort. 2025) |
| 108 | Providing and Displaying Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge. 5.13 (dsr hort. 2025) |
| 109 | Providing and Displaying Cyprus golden well shaped developed with good colored foliage fresh & healthy 60 to 75 cm ht in 30 cm Earthen Pot as per direction of the officer-in-charge. 5.17 (dsr hort. 2025) |
| 110 | Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm Cement Pot as per direction of the officer-in-charge. 5.28 (dsr hort. 2025) |
| 111 | Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 6.1 (dsr hort. 2025) |
| 112 | Providing and stacking of Asparagus marrie, well developed 15 to 20 leaves, full of branches and foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 6.3 (dsr hort. 2025) |
| 113 | Providing and stacking of Cuphea chinensis of ht. 20-30 cm full of branches and healthy foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 6.10 (dsr hort. 2025) |
| 114 | Providing and stacking of Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.6.14 (dsr hort. 2025) |
| 115 | Providing and stacking of Ophiopogon jaburan (variegated) ,full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge. 6.21 (dsr hort. 2025) |
| 116 | Providing and stacking of Alstonia scholaris of height 150-165 cm. in bagof size 25 cm as per direction of the officer-in-charge. 7.4 (dsr hort. 2025) |
| 117 | Providing and stacking of Butea frondosa (Flame of Forest) of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.7.13 (dsr hort. 2025) |
| 118 | Providing and stacking of Cassia siamea of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. 7.17 (dsr hort. 2025) |
| 119 | Providing and stacking of Bauhinia tomentosa (yellow) of height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge. 8.2 (dsr hort. 2025) |
| 120 | Providing and stacking of Calliandra hybrida of height 105-120 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.8.7 (dsr hort. 2025) |
| 121 | Providing and stacking of Cassia laevigata of height 45-60 cm. in earthenpots of size 20 cm as per direction of the officer-in-charge. 8.11 (dsr hort. 2025) |
| 122 | Providing and stacking of Chandni dwarf of height 15-20 cm., well branched in earthen pots of size 20 cm as per direction of the officer-in-charge. 8.14 (dsr hort. 2025) |
| 123 | Providing and stacking of Nyctanthes arbor-tristis (Hasingar) of ht. 90-105 cm in Earthen pots of size 20 cm as per direction of the officer-in-charge. 8.54 (dsr hort. 2025) |
| 124 | Providing and stacking of Allamanda violacea of height 30 cm to 45 cm. in poly bag of size 20 cm as per direction of the officer-in-charge. 9.2 (dsr hort. 2025) |
| 125 | Providing and stacking of Clerodendrum thomsoniae of height 30 cm.to 45 cm in 20 cm size of poly bag & as per direction of the officer-in-charge.9.6 (dsr hort. 2025) |
| 126 | Providing and stacking of Vernonia elaegnifolia (curtain creeper) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. 9.14 (dsr hort. 2025) |
| 127 | Providing and Stacking of Aprajita Blue well developed in poly bag of size 20 cm as per direction of the officer-in-charge.11.17 (dsr hort. 2025) |
| 128 | Providing and Stacking of Aprajita White well developed in poly bag of size 20 cm as per direction of the officer-in-charge.11.18 (dsr hort. 2025) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 25 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 28 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender