Tender For Certain Joinery Repairs To Otm Accn In Aor Of Age B&R-Ii (South) Ambala Under Ge (South) Ambala Cantt.
Tender Value
30 Lakhs
Estimated cost
Bid Submission
07 Nov 2026
2 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ambala → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Certain Joinery Repairs To Otm Accn In Aor Of Age B&R-Ii (South) Ambala Under Ge (South) Ambala Cantt.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down wooden chowkats or frames with shutter (without taking off shutter from the frames), area not exceeding 1.5 Sqm each and removal from site including iron mongry hold fasts etc, complete all as specified and directed by Engineer-in-Charge. |
| 2 | Taking down wooden chowkats or frames with shutter (without taking off shutter from the frames), area exceeding 1.5 Sqm and not exceeding 4.00 Sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 3 | Taking down shutter of any descritption exc 1.00 sqm each but not exc 3.00 sqm each including removal from site, complete all as specified and directed by Engineer-in-Charge. |
| 4 | Supply and fixing of Steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc complete all as shown on drawing No. TD-219(c) sheet 1/3 to 3/3 and TD-220(c) sheet 1/3 to 3/3 as applicable complete inclusive of guared bars 8 to 10mm square bar including taking down old unserviceable windows Note: (i) For the purpose of measurement and payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery (iii) Glazing, wire mesh and painting grill shall be measured and paid for separately. |
| 5 | Supply and fixing Steel ventilators, fixing type, with glazing bars complete all as specified and directed by Engineer-in-Charge. |
| 6 | Supply and fixing (in repair) partly glazed aluminium alloy anodized (powder-coated) partition (Area of each panel not exceeding 1.5 Sqm each) with frame of size not less than 100 mm x 44.4 mm x 2 mm including packing with rubber gasket, standard aluminium beading around both sides including 6mm thick plain coloured bakelite sheet or acrylic boards, prelaminated both side with one side decorative choice lamination for fixing in bottom panel of aluminium partition as required complete all as specified and directed by Engineer-in-Charge. Notes :-1. Glass pane shall be measured and paid separately. |
| 7 | Supply and fixing (in repair) aluminium alloy anodized (powder-coated) door frame and partly glazed shutters with hollow aluminium anodized sections including 6mm thick plain coloured bakelite sheet or acrylic boards, prelaminated both side with one side decorative choice lamination for fixing in bottom panel as specified including aluminium alloy anodized snap type beads, dish type door handles, glazed clip, jointing cleats, rubber packing, gasket, dead lock 4 levers, 02 Nos aluminium alloy anodized tower bolts to each leaf etc. including fixing frame to wall/RCC members etc. with rawl plugs complete all as specified and directed. Sections of frame and door shall be as follows : -(a) Door Frame single groove 101.6 mm x 44.45 mm x 2.15mm thick (b) Shutter top 47.62 mm x 44.45 mm x1.95 mm thick. (c) Shutter bottom 114.30 mm x 44.45 mm x 2.1 5mm thick.(d) Shutter vertical 85 mm x 44.45 mm x 1.80 mm thick.(e) Shutter middle 83.5 mm x 44.45 mm x 2.40mm thick.(f) Gauging clip weighing not less than 0.097kg/metre.Notes :-1. Glass pane shall be measured and paid separately. |
| 8 | Supply and fixing (in repair) aluminium alloy anodized (powder-coated) window frame with double shutters open able type, with aluminium sections as specified for casement windows with double shutters including aluminium alloy anodized snap type beads, handles, stainless steel hooks and eyes, aluminium anodized barrel tower bolts, glazing clips, joint cleats, rubber packing, gaskets etc for series-B “ Jindal” section numbers for casement window.complete all as specified and directed comprising of followings :-(a)Frame of section 101.6mm x 44.45mm x 2.10 mm thick and section for shutter 47.62 mm x 44.45 mm x1.95 mm thick.(b) Mullion 53 mm x 52 mm x 2 mm thick not less than 1.065 kg/mertre.(c) Glazing clip weighing 0.259kg/mtr. (d) Window shall be provided with 02 Nos. of tower bolt for single leaf and 03 Nos. of tower bolts for double leaf. Tower bolts shall be aluminium alloy anodized weighing 0.302kg/mtr. Handles shall be aluminium anodized ‘D’ type handle of size 98 mm and thickness 2.37mm weighing 0.875kg/mtr and 01 no for each open able leaf. Notes :-1. Glass pane shall be measured and paid separately. |
| 9 | Supply and fixing in repair position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) three track window ( two shutters glazed and one shutters wire gauge) with frame, glazed with 5.5 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below,including the cost of EPDM rubber /neoprene gasket required complete all as specified and directed by Engineer-in-Charge. (a) Frame (top and side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20831)(b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20832)(c) Top and side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20738)(d) Shutter Interlock Section shall be be of size 18.00 x 40.00 x 1.45 (Section No 20737)(e) Bottom Members of shutter Section shall be of size 18.00 x 40.00 x 1.55 (Section No 20736)Note:- Section No given above are of make Jindal, Contractor may use similar section of other make mentioned in relevent Appx |
| 10 | Supply and fixing in repair powder coated anodised aluminium grill made of mesh size 100x100mm of bar 8mm dia using U channel 25x12mm fixing to aluminium frame work complete all as specified and directed by Engineer-in-Charge. |
| 11 | Supply and fixing in repair of rubber Neoprene/ EPDM rubber gasket for aluminium door and windows complete all as specified and directed by Engineer-in-Charge. |
| 12 | Supply and fixing in repair of double action floor spring hydraucally regulated made of 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, govering pivot made of brass, other parts made of mild steel heavy duty, suitable for aluminium doors complete all as specified and directed by Engineer-in-Charge. |
| 13 | Supply and fixing of 5 mm thick tinted glass in square exc 0.5 sqm in each pane with heat reflecting properties , fixing to aluminium frame with glazing clips, etc.complete all as specified and directed by Engineer-in-Charge. . |
| 14 | Supply and fixing 3mm Sheet glass, ordinary quality, in squares not exc 0.5 sq. m each and glazing with beads fixing with metal panel pins complete all as specified and directed by Engineer-in-Charge. |
| 15 | Supply and fixing Pressed steel frames for doors of size 165mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, complete all as specified and directed by Engineer-in-Charge. |
| 16 | Supply and fixing Pressed steel frames for doors of size 105mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, complete all as specified and directed by Engineer-in-Charge. |
| 17 | Material and Labour IInd class hardwood factory made 30mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) supplt and fixing to choukats complete all as specified and directed by Engineer-in-Charge at site. |
| 18 | Supply and fixing for galvanized mild steel wire cloth with 0.63mm nominal dia of wire and average width of aperture 1.40mm fixing with finned tacks or galvanized wire staple complete all as specified and directed by Engineer-in-Charge. |
| 19 | Supply and fixing for 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed by Engineer-in-Charge. |
| 20 | Supply and fixing factory made 35mm thick 2nd class hardwood plain frame paneled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides. The size of rails stile as per IS:1003 (Part I) kiln seasoned and chemically treated, complete all as specified and directed by Engineer-in-Charge. Note : Manufacturers Test cert to be submitted before incorporattion. |
| 21 | Supply and fixing 250 mm aluminum anodised sliding door bolts, , with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and directed by Engineer-in-Charge. |
| 22 | Material and labour for preparing new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint(first quality) over a coat of primer complete all as specified and directed by Engineer-in-Charge. |
| 23 | Material and labour for painting surfaces of wood (new) of any description not otherwise described over 10cm width of girth by applying two coats, of synthetic enamel paint over a coat of pink primer including preparation complete all as specified and directed by Engineer-in-Charge. |
| 24 | Supply and fixing factory made PVC hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixing to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical number and minimum 02 Nos. for horizontal member), complete all as specified and directed by Engineer-in-Charge. |
| 25 | Supply and fixing Factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm plain colour PVC sheet on back face including fixing in frame at site with 03 Nos SS hinges, 02 Nos aluminium tower bolt 200 mm, 02 Nos aluminium handle 150 mm for each shutter all as per specification and drawing complete all as specified and directed by Engineer-in-Charge. |
| 26 | Material and Labour for PCC 1:2:4 type B-1, (using 20mm graded mechanically crushed stone aggregate) as in bed blocks for hold fasts, complete all as specified and directed by Engineer-in-Charge. |
| 27 | Supply and fixing of lead free PVC celuka ply 18mm thick (minimum density 600kg/Cum of single side rigid lamination of approved colour and other side plain white colour, fixing with stainless steel screws solvent cement /adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer 's specification incuding dismantling baording, any description fixing in any posiition with nails etc complete all as specified and directed by Engineer-in-Charge. |
| 28 | Supply and fixing of plain fillets second class hardwood .square,rectangular or triangular in section ,Exc 6 and n exc 13 sq cm clean sawn, secured with nails or brads, complete all as specified and directed by Engineer-in-Charge. |
| 29 | Supply and fixing plain fillets second class hardwood .square,rectangular or triangular in section n exc 3 sq cm bullnosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge. |
| 30 | Supply and fixing continuous (Piano) hinges mild steel, bright finish or electro galvanised, width of flap 30mm complete all as specified and directed by Engineer-in-Charge. |
| 31 | Supply and fixing 100mm long hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixing with screws complete all as specified and directed by Engineer-in-Charge. |
| 32 | Supply and fixing in repairs Aluminium alloy, anodised, sliding door bolt, 250mm long, with hasp, staple (bolt type) with clamps bolt not less than 16mm dia including fixing bolts and nuts etc complete all as specified and directed by Engineer in charge. |
| 33 | Supply and fixing 75mm Butt hinges, heavy weight, cold rolled mild steel, and fixing as in repairs, complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply and fixing 100mm Butt hinges, heavy weight, cold rolled mild steel, and fixing as in repairs, complete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply and fixing for Aluminium anodised, 200mm long barrel tower bolts of extruded section and fixing complete all as specified and directed by Engineer-in-Charge. |
| 36 | Supply and fixing as in repairs for aluminium anodised, 200mm long barrel tower bolts of extruded section and fixing complete all as specified and directed by Engineer-in-Charge. |
| 37 | Supply and fixing 150mm long extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply and fixing 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified and directed by Engineer-in-Charge. |
| 39 | Supply and fixing any Continuous (piano) hinge, mild steel, bright finish (width of flap 40mm when open), complete all as specified and directed by Engineer-in-Charge. |
| 40 | Supply and fixing in repair 125mm Double action spring hinges, mild steel with steel wire spring, stove enamelled, black, complete all as specified and directed by Engineer-in-Charge. |
| 41 | Supply and fixing Mild Steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge. |
| 42 | Supply and fixing in repairs 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete if fixing to steel/ concrete chowkats with flat iron 40x3 mm size 75 cm long with necessary bolts, etc. complete all as specified and directed by Engineer in charge |
| 43 | Supply and fixing in repair 150mm size extruded aluminium alloy handles, fabricated type, anodised in repairs, complete all as specified and directed by Engineer-in-Charge. |
| 44 | Supply and fixing in repair of aluminium pre coated of choice colour designed type 25 mm tubular rod in curtain rod, 1.6mm fancy type including PVC golden colour brakets, latto and wall to wall socket etc.complete all as specified and directed by Engineer-in-Charge. |
| 45 | Supply and fixing in repairs 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixing in floor complete all as specified and directed by Engineer-in-Charge. |
| 46 | Supply and fixing in repair Door closer of body cast iron hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixing complete all as specified and directed by Engineer-in-Charge. |
| 47 | Supply and fixing as in repairs Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixing with tinned tacks, or galvanised wire staples, complete all as specified and directed by Engineer-in-Charge. |
| 48 | Repair related to welding repair works such as repair to grills, guard bars, steel windows and steel door etc., by deploying Welder and helper for welding of not exc 6mm thick and not exc 2.5cm in lenth complete all as specified and directed by Engineer-in-Charge. |
| 49 | Repair related to welding repair works such as repair to grills, guard bars, steel windows and steel door etc., by deploying Welder and helper for welding of exc 6mm and not exc 9 mm thick and exc2.5cm and not exc 5.0cm in lenth complete all as specified and directed by Engineer-in-Charge. |
| 50 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixing with beads, complete all as specified and directed by Engineer-in-Charge. |
| 51 | Hacking out old broken glass from metal frame including punching or drilling out old glazing pins/spring clips, complete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply and fixing in repair Sheet glass, 3mm ordinary quality and glazing with oil putty in square not exc 0.5 sq. m in each pane, complete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply and fixing in repair Sheet glass, 3mm ordinary quality and glazing with oil putty in square not exc 0.5 sq. m in each pane and sheet glass is ground or obscured or frosted, on one side, complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply and fixing in repair Sheet glass, 3mm ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane, complete all as specified and directed by Engineer-in-Charge. |
| 55 | Resecuring chowkhat or frame without taking down Chowkhats or frames not exc. 1.5 sq. m each, complete all as specified and directed by Engineer-in-Charge. |
| 56 | Resecuring without taking down Chowkhats or frames exc. 1.5 sq. m and n exc 4.0 sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 57 | Resecuring or easing and adjusting shutters of description wooden/steel n exc 1.00 sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 58 | Resecuring or easing and adjusting shutters of description wooden/steel exc 1.00 sqm n exc 2.0 sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 59 | Supply and fixing in repairs for stainless steel plate rack standard size 900mmx600mm x 200mm complete and fixing with rawl plug and steel screws of wt not less than 5 kg each, complete all as specified and directed by Engineer-in-Charge. |
| 60 | Supply and fixing of 5 mm thick plain colour PVC sheet hollow interlocking wall panelling of width 250 mm for wall panelling inclusive of fixing on wall with screws and solvent alongwith PVC 'U' and 'L' beading at corner and end portion where ever required of matching colour including taking down of existing wall lining, board or insulation board/panelling including cover fillets of any type and thick complete all as specified and directed by Engineer-in-Charge. NOTE : - Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fans etc after carrying out necessary relevant work and making good to match with existing surface effected for this area etc complete all as specified and directed by Engineer-in-Charge. |
| 61 | Supply and fixing of 5 mm thick plain colour PVC sheet, solid PVC wall paneling/ lining PVC sheet inclusive of solvent cement and fixing at site with and including 5 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing on wall to make PVC frame as per specification and directed including taking down of existing wall lining, board or insulation board including cover fillets of any type and thick complete all as specified and directed by Engineer-in-Charge. NOTE : - Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fans etc after carrying out necessary relevant work and making good to match with existing surface effected for this area etc complete all as specified and directed. |
| 62 | Supply and fixing of semi perforated false ceiling 12 mm thick with micro tegular edged at all height with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and pattern having moisutre content less than 2%, humidity resistance of 99%, NRC 0.60 to 0.85 as per IS 8225-1987, non combustible as per BS 475 (Part-4) 1970 and light code description unit code No 429 Sub Head 26. New Technologies and materials reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metal T -grid of hot dipped galvanised iron section of 0.33 mm thick ( galvanised @ 120 gms/ sqm including both sides) comprising of main T- runners of size 15x 32mm of length 3000mm, cross T of size 15 x32 mm of length 1200mm and secondary intermediate cross T of size 15 x 32 mm of length 600 mm to from grid module of size 600 x 600 mm, suspended form ceiliing using galvanised mild steel items (Galvanised @ 80 gm/sqm) i.e. 50 mm long, 8mm outer diameter M-6 dash fastners, suspended with GI wire of any dia and L shape level adjuster of size 85 x 25 x 2mm. galvanised iron perimeter wall angle of size 24 x 24 x 0.4 mm of length 3000 mm to be fixing on perimeter wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall SS screws. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge including dismantling existing false ceiling textile coverings including frames (if any) and cover fillets complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply and fixing of false ceiling at all heights of perforated with fleece 595 mm x 595 mm x 0.5 mm TEGULAR EDGE TILES in global white powder quoted with 60-70 micron front coating and including regular 24 mm wide T-section flange colour white having rotary stitching on the main runner with web height 26 mm, exposed grid system including frame work comprises of main runner spaced at 1200 mm max (centre to centre), hangers (GI wire of any dia) to be fixing by hiliti consisting of HLS sleeve anchor fastencer of thread size 6.5 mm x 25/5 with soffit cleat made of galvinised steel of size 27 mm x 37mm x 25mm x 1.6mm and level clip in dimensions of 85mmx30mm 0.8mm at 600x1200 intervals. The last hanger at the end of each main runner shoud not be greater than 450 mm from the adjacent wall. Flush fitting 1200 mm long cross tees (with double stiching) to be interlocked between main runner at 600 mm shall be 'T'shape section with single rotary stitching made of GS sheet and of size 15 mmx32mm and 3000mm long, crosssed runner shall be 'T' shaped with double rotary stiching made of GS sheet and size 15 mmx 32mm x 1200 mm long and perimeter wall angle shall be made from GS sheet and of size 19mm x 19mm and 3000mm long, colour white, centre to form 600 mm x 600 mm modules, cut cross tees longer than 600 mm to be supported independently, 600mm x 600mm modules to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be wall angles of size 3000x22x22mm, secured to walls at 450mm max (centre to centre), complete including taking down existing ceiling boards (fibre, pulp, insulation etc) or insulation boards/slab etc ant thickness including cover fillets of any description complete all as specified and directed by Engineer-in-Charge. |
| 64 | Supply and fixing of PVC false ceiling consisting of 600 mm x 600 mm, 5mm (+ 0.25) thick plain embossed PVC sheet of density 600 Kg/Cum manufactured by an ISO-9001-2015 certified company, used as panel insert in a frame work made using anodised aluminium T-section of sizes 1\\" x 1\\" (25 mm x 25 mm, 1 mm thick) in square pattern of grid sizes of 2' x 2' (600 mm x 600 mm). The aluminium framework is supported from the ceiling with the help of 'J' hook and G.I. wire of required sizes to maintain proper level etc. The aluminium frame work is supported on the side wall with the use of aliminium L- Section of size 1\\"X1\\" (25mmX25mm, 1mm thick) Angles etc. complete as per direction of Engineer - In- Charge, Manufacturer's specification and drawing including taking down existing ceiling boards (fibre, pulp, insulation etc) or insulation boards/slab etc ant thickness including cover fillets of any description complete all as specified and directed by Engineer-in-Charge. NOTE : - Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fans etc and making good to match with existing surface effected for this area etc complete all as specified and directed. |
| 65 | Resecurig /adjusting existing false ceiling grid any type and making reqd tightening to remove sag portion/depression in false ceiling grid including replacement of missing sections/suspenders tec complete all as specified and directed by Engineer-in-Charge. |
| 66 | Supply and fixing pegs set of 6 Nos, power coated GI fixing with cadmium plated screws as as in repairs, complete all as specified and directed by Engineer-in-Charge. |
| 67 | Supply and fixing in repair of 1.25mm thick steel rolling shutters, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type including taking down old rolling shutter complete all as specified and directed by Engineer-in-Charge. |
| 68 | NOTE:- Amount of credit of Rs. 1,28,977.50 for retrieved materials is mentioned in Schedule of Credit Page No 19.00 & 20.00 of tender documents in pdf form which will be deducted offline while acceptance of tender. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysNov 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender