Tender For maintenance Of Residential Buildings At Ambassa Pwd Quarter Complex/ Sh:-Mtc. Of Pwd Staff Quarters No. T-Ii- 31, T-I-06 & 07, At Ambassa Under Ambassa Division, Pwd (R&B)..
Tender Value
13.71 Lakhs
Estimated cost
Bid Submission
02 Nov 2026
6 days left
EMD
27430
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhalai → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for maintenance Of Residential Buildings At Ambassa Pwd Quarter Complex/ Sh:-Mtc. Of Pwd Staff Quarters No. T-Ii- 31, T-I-06 & 07, At Ambassa Under Ambassa Division, Pwd (R&B)..
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto1.5m, disposed earth to be levelled and neatly dressed.-All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.-All kinds of soil |
| 3 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering --All work upto plinth level:4.1.5:- 1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) |
| 5 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-5.3.2:- 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 6 | Centering shuttering including struttings, propping etc. and removal of form work for: 5.8.4.2:- Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 7 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.5.20.4:- Thermo-Mechanically Treated bars of grade Fe 500D or more |
| 8 | First class brick work in foundation and plinth including cost of all materials as required complete:- 6.1.3:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 9 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-6.3.3:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 10 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-6.12.3:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 11 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :8.1.3:- Local Teak Wood |
| 12 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters.8.19.1:- 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 13 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 gradded stone aggreegate 20 mm nominal size) |
| 14 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.8.99.1:-Single rubber stopper |
| 15 | Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality) |
| 16 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :8.94.1:-300x16 mm |
| 17 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :8.95.1:-300x10 mm |
| 18 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :8.98.1:-125 mm |
| 19 | Providing and fixing to existing door frames.8.115.1 :- 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised /plastic brackets of size 75×220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanised MS tube of size 20×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \\"H\\" Section, a UPVC hollow section of size 100×24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galvanised MS \\"U\\" cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontaly 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter). |
| 20 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19×19mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall usuing MS screws of 65/100 mm size complete as per manufacturers' specification and direction of Engineer-In-Charge |
| 21 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622- 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in charge in skirting, risers of steps and dados, laid over 12mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge. 10.40.1:- 450 mm X 300 mm in all shades and design. |
| 22 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.10.41.1:- Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles10.41.1.1:- 300 mm x 300 mm in all shades and designs |
| 23 | Providing and fixing Precast chequered cement concrete tiles18mm thick, laid in footpath & courtyard, on 20 mmthickbedof cementmortar1:4(1cement :4fine sand) jointed with neat cement slurry including rubbing and cleaning etc. all complete as per direction of Engineer-in-charge. 10.54.1:- In dark shade using ordinary cement |
| 24 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592TypeA including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge :11.55.2 :-Single socketed pipe - 110 mm OD |
| 25 | Providing and fixing on wall face unplasticised-PVC moulded fittings/ accessories for unplasticisedRigid PVCrainwaterpipesconformingto IS : 13592Type-A including jointing withseal ring conforming to IS : 5382 leaving10mmgap for thermal expansionetc. complete as per direction of Engineer-in-charge : |
| 26 | 11.56.1:- Coupler11.56.1.2 :-110 mm |
| 27 | 11.56.3 :-Single equal tee without door11.56.3.2 :-110x110x110mm |
| 28 | 11.56.4 :-Single equal tee with door11.56.4.2: 110x110x110mm |
| 29 | 11.56.5 :-Bend 87.5°11.56.5.2:- 110mm |
| 30 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete as per direction of Engineer-in-charge..11.57.2:- 110mm |
| 31 | 12 mm cement plaster of mix12.1.2:- Cement mortar 1:4 (1 cement : 4 fine sand) |
| 32 | 15 mm cement plaster on the rough side of single or half brick wall of mix:12.2.2:- Cement mortar 1:4 (1 cement : 4 fine sand) |
| 33 | 6 mm cement plaster of mix :12.9.1:- Cement mortar 1:3 (1 cement : 3 fine sand) |
| 34 | Neat cement punning. |
| 35 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of TestCertificate issued by the Manufacturer] :12.35.1:- New work ( two or more coats) over and including waterthinnable priming coat with cement primer. |
| 36 | Finishing walls with premium acrylic smooth exterior paint with Silicon additives of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by theManufacturer] :12.42.1:- New work ( two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 37 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides withrequired EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :- |
| 38 | 16.1.1:- For fixed portion of approved quality:-16.1.1.1:- Anodised aluminium (anodised transparent or dyed torequired shade according to IS: 1868, Minimum anodiccoating of grade AC 15). |
| 39 | 16.1.2:- For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately ):-16.1.2.1:- Anodised aluminium (anodised transparent or dyed torequired shade according to IS: 1868, Minimum anodiccoating of grade AC 15). |
| 40 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :-16.3.1:- With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 41 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-16.12.1:- Anodised aluminium of grade AC 15 ). |
| 42 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with :17.14.1:- Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 43 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :18.2.1:- W.C. pan with ISI marked white solid plastic seat and lid |
| 44 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the wallswherever require :18.7.1:- White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 45 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 46 | 18.23 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizesrespectively. |
| 47 | Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. |
| 48 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.18.28.1:- Semi rigid pipe18.28.1.1:- 32 mm dia |
| 49 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 50 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 51 | Providing and fixing toilet paper holder :18.34.1:- C.P. brass |
| 52 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms. |
| 53 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.18.73.2:- 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 54 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:18.83.1:- Single socketed pipe - 110 mm OD |
| 55 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conformingto IS : 5382 leaving 10 mm gap for thermal expansion: |
| 56 | 18.84.1 Coupler18.84.1.2:- 110 mm |
| 57 | 18.84.3 Single equal tee without door18.84.3.2 110x110x110mm |
| 58 | 18.84.4 Single equal tee with door18.84.4.2 110x110x110mm |
| 59 | 18.84.5 Bend 87.5°18.84.5.2 110mm |
| 60 | 18.84.7 Double equal junction of required degree without door18.84.7.2 110x110x110mm |
| 61 | 18.84.8 Double equal junction of required degree with door18.84.8.2 110x110x110mm |
| 62 | 18.84.13 Terminal Guard18.84.13.2 110mm |
| 63 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water, soil, waste & vent pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete.18.85.2 110mm |
| 64 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc. |
| 65 | 19.8.1:- 15 mm nominal outer dia .Pipes. |
| 66 | 19.8.2:- 20 mm nominal outer dia .Pipes. |
| 67 | 19.8.3:-25 mm nominal outer dia .Pipes. |
| 68 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:893119.49.1:-15 mm nominal bore |
| 69 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.19.52.1:- 15mm nominal bore. |
| 70 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931.19.53.1:- 15 mm nominal bore. |
| 71 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 72 | Providing and fixing unplastisised P.V.C. Connection pipe with PTMT Nuts of approved quality and colour.19.74.2:- 15 mm nominal bore with 45 cm length. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender