Tender For Renovation Of Type Ii Quarter (No 1 & 2) By Providing Tubular Trusses, Galvalume Sheets Roofing, Mdf Ceiling ,Construction Of Septic Tank, Water Supply & Painting Etc. At P.R. Bari Under S.P South, Belonia.
Tender Value
8.72 Lakhs
Estimated cost
Bid Submission
05 Nov 2026
17 days left
EMD
17441
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Type Ii Quarter (No 1 & 2) By Providing Tubular Trusses, Galvalume Sheets Roofing, Mdf Ceiling ,Construction Of Septic Tank, Water Supply & Painting Etc. At P.R. Bari Under S.P South, Belonia.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling GS sheet roofing including ridges, hips,valleys, gutters wind ties etc. including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50 m etc.complete as per direction of the Engineer- in-charge. |
| 2 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 3 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge. |
| 4 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :a) Of area 3 sqm and below. |
| 5 | Demolishing brick work including stacking of serviceable materials and disposal of unserviceable materials with all lifts and upto a lead of 50m etc. complete as per direction of the Engineer- in-charge:-In cement mortar. |
| 6 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. a) Hot finished welded type tubes. |
| 7 | Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:- (1) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 8 | First class brick work in foundation and plinth including cost of all materials as required complete:- (1) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 9 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-(1) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 10 | Providing and fixing white vitreous china water closet squatting pan (Indian type). I) Orissa pattern W.C. pan of size 580x440 mm |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All work upto plinth level: a) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 12 | b) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) |
| 13 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (All kinds of soil ) |
| 14 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 15 | Centering shuttering including strutting, propping etc. and removal of form work for: a) Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank |
| 16 | Reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding all complete above plinth level.i)Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 17 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies,shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases upto floor five levelexcluding the cost of centring, shuttering, finishing and reinforcement.i)1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick |
| 18 | Constructing soak pit 1.20 x 1.20 x 1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 19 | 12 mm cement plaster of mix (1) In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 20 | 12 mm cement plaster of mix in/c neat cement punnig a) In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 21 | Providing and fixing factory made UPVC door frame made of UPVC extruded, section having an overall dimension, as below (tolerance +/- 1mm) with wall thickness 2.0mm+/- 02mm. corners of the door frame to be jointed with galvanized brackets and stainless screws, joint mitred and plastic wilded. The hinge side vertical of the frames reinforced by galvanized MS tube of size 19 × 19 mm and 1 mm +/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-Charge. a) Extruded section Profile size 48x40 mm. |
| 22 | Providing and fixing to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised /plastic brackets of size 75×220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanised MS tube of size 20×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \\"H\\" Section, a UPVC hollow section of size 100×24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galvanised MS \\"U\\" cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontaly 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter). |
| 23 | Providing wood work in frames of doors, windows,clerestory windows and other frames, wrought framed and fixed in position :i) Local Teak Wood |
| 24 | Providing and fixing 25 mm thick shutters for cup board etc. : i) Panelled or panelled & glazed shutters : a) Local teak wood including ISI marked anodised aluminium butt hinges with necessary screws. |
| 25 | Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position : a)Local Teak Wood. |
| 26 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : a)Local Teak Wood . i) 50×12 mm |
| 27 | Providing and fitting ,fixing Medium Density Fiber hard board sheet ceiling with wooden beading ,nails etc. complete as per direction of Engineer –in-Charge.(wooden beading will be paid separately) a) 6 mm thick sheet. |
| 28 | Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-incharge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and as per direction of Engineer-in-charge. a) 0.50mm thickness |
| 29 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side etc. complete as per direction of Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm: a) 0.50mm thickness |
| 30 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 -2017 of proved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. i) Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles. a) 300 mm x 300 mm in all shades and designs |
| 31 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge. i) 450 mm X 300 mm in all shades and design |
| 32 | Providing and fixing unplasticised Polyvinyl Chloride (UPVC) pipes including all UPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per the direction of Engineer-in-Charge. (a) Internal & outer work. Exposed on wall. 25 mm dia |
| 33 | b)20 mm nominal outer dia .Pipes. |
| 34 | b) 40 mm nominal outer dia .Pipes. |
| 35 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 a)15 mm nominal bore |
| 36 | Providing and fixing PTMT stop cock of approved quality and colour. i) 15 mm nominal bore, 86mm long, weighing not less than 88 grams. |
| 37 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : i) 25 mm nominal bore |
| 38 | ii) 40 mm nominal bore |
| 39 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal xpansion: (1) Single socketed pipe - 110 mm OD |
| 40 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water ,soil, wast,& vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: (i) Bend 87.5degree a)110 mm |
| 41 | (ii)Single equal tee with door a) 110 x 110 x110mm |
| 42 | (ii)Coupler 110mm |
| 43 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :i) White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps. |
| 44 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. a ) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190 gms. |
| 45 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 46 | Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised -PVC rain water pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc. complete as per direction of Engineer-in-charge. i) 110mm |
| 47 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: A) Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture . |
| 48 | Painting with synthetic enamel paint ( one or more coats ) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge. |
| 49 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture on old work ( one or more coats ) including preparation of surface as required complete as per direction of the Engineer in charge. |
| 50 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : A) New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 51 | Distempering with 1st quality washable acrylic distemper of approved brand and manufacture and of required shade on old work ( one or more coats ), to give an even shade as required complete as per direction of the Engineer in harge. |
| 52 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : a) New work ( two or more coats) over and including water thinnable priming coat with cement primer. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysNov 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender