Tender For Rep And Maintenance Of E/M Installation And Connected Items At installation Shivaji Lonavla (8505/E8)
Tender Value
19 Lakhs
Estimated cost
Bid Submission
09 Nov 2026
24 days left
EMD
38000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Rep And Maintenance Of E/M Installation And Connected Items At installation Shivaji Lonavla (8505/E8)
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of concrete in ground floors (un re-inforced) and paving n.exc. 15 cm thickness (below or above ground level) and removal of demolished materials out of MD land complete all as specified and directed. |
| 2 | M&L for 30mm sand cushioning under interlocking in floors including watering and consolidation. |
| 3 | M&L for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60 mm thickness, M-35 with grey cement and no pigment grade all as specified and directed. |
| 4 | M & L for cement concrete type D-2 1:4:8 (40mm graded aggregate) 75mm tk as in subbase. |
| 5 | M&L for glossy finished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 20mm screed bed in CM (1:6) complete all as specified and directed. |
| 6 | M&L cement filleting in CM 1:4, sectional area n.exc 25 sq cm in repair complete all as specifed and directed |
| 7 | Demolition of brick work or stone boulder masonry,built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, and precast concrete articles complete all as specifed and directed. . |
| 8 | M&L Pre-cast AAC blocks masonry GR-1 of size 600x200x100mm and setting in CM 1:6,complete complete all as specified and directed |
| 9 | M&L Providing, cement concrete of 1:2:4 B1 (20mm graded aggregate) as in copings, post, etc complete all as specifed and directed. |
| 10 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 11 | M/L for rendering 15 mm thick in CM 1:6 on brick work or concrete surfaces to be finished even and smooth (without using extra lime or cement) complete all as specifed and directed |
| 12 | M & L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces to be finished even and smooth (without using extra lime or cement) complete all as specifed and directed |
| 13 | supply only water proofing compound |
| 14 | M&L for pripration of old/New existing treatment of walls, chajjah by brooming down with steel wire brush, scraping down smoke shoot, molds, moss and efflorescent salts and trading oil and greasy spots and rubbing down, Washing with water by jet spray and allow to dry 4-6 Hrs and applying two coats of excel anti peel at an interval of 4-6 Hrs over a coat of exterior primer/Excel alkali primer over a coat of Nero wash/fungicidal wall wash solution (allow to dry overnight) complete all as per manufacturer instructions and as directed by EIC. |
| 15 | Dismantling of fencing wire mesh ,any type complete all as specified and as directed. |
| 16 | Dismantling posts or struts (wood ,steel or RCC ) any section ,including taking out embaded portion concrete ,brick work ,masonary,etc and making good disturbedground complete all as specified. |
| 17 | Taking down chowkat or frame with shutter (without taking off shutter from the frames) not exceeding 1.5 Sqm each complete as specified and directed. |
| 18 | Dismantling structural steel work including doors, gates but excluding framed truss etc. |
| 19 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing including 100 mm long 8 Nos Hold fast/ Screws. |
| 20 | Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 21 | S&F in 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed. |
| 22 | S/F 150mm length Aluminium handles, cast type, anodised. |
| 23 | S&F 200mm length Aluminium anodised, barrel tower bolts of extruded section and fixed. |
| 24 | S&F mild steel section and embedding in concrete, posts or struts in fencing/compound wall, Doors or gate etc. including cutting tops to shape as directed drilling holes notching for wire etc. flat iron fillets (for securing wire mesh) including all necessary drilling, bolting etc and similar work conforming to Fe-410-0). complete all as specified and directed. |
| 25 | M&L for preparation of new surfaces of steel, of any description, not otherwise described, over 10 cm in width or girth and applying two coats of epoxy paint over a coat of anti corrosive epoxy primer complete all as specified and directed. |
| 26 | Supply only chain link fencing & line wire, MS galvanised of any size and type complete all as specified and as directed. |
| 27 | Fixing for chain link fencing including line wires, any mesh, size, rails, straining bolts, etc. including provision of binding wire. (Chain link fencing and line wire shall be paid at supplied only rate) complete all as specifed and directed. |
| 28 | Repairs to Steel rolling shutters, any type n. exc 10 Sqm as specified including repair replacement of top cover, anchoring rod, greasing, hasp and staple and making operational by manual including hasp and staple and applying two coat of synthetic enamal paint; erected in position as indicated, complete |
| 29 | S&F in repairs 1 mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete; push pull or manual type complete all as specified and as directed. |
| 30 | S&F for Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed. |
| 31 | S&F for Ball bearing for rolling shutters complete all as specified and as directed. |
| 32 | Cleaning of bushes in side the structure by manually and getting out all bushes and grasses from site complete all as specified and as directed. |
| 33 | Supply & spreading for Hardcore of broken stone or boulders of gauge n exc. 40 mm, deposited, levelled in layers n exc. 15cm thick over watered and rammed to a true surface complete all as specified and as directed. |
| 34 | Taking down steel/aluminium windows/ventilator complete with frames and shutters (without taking off the shutters) of any size complete all as specified and as directed. |
| 35 | M&L for powder coated aluminium three track and three shutter (of equal width) sliding type window without sash bars including necessary jointing clips, rubber packing, neoprene rubber gasket, aluminium snap beading, screws, aluminium fittings, handles, locking arrangement (star lock), bearings two No's for each shutter with 4.00mm thick sheet glass for glazing shutters & stainless steel wire cloth of 0.36mm nominal dia of wire & average width of aperture 1.40mm for wire gauge shutters including following powder coated sections as given in 'JINDAL' catalogue complete all as specified and as directed :- (i) Frame (Bottom)-20620. (ii) Frame (Top & Side)-20621. (iii) Shutter vertical (Handle lock)-20846. (iv) Shutter vertical (Int lock)-20845. (v) Shutter (Top)-20844. (vi) Shutter (Bottom)-20847. Note :- (i) The window opening shall be provided with three shutters of equal width. (ii) Two shutters shall be glazed shutters & one shutter shall be with stainless steel wire cloth all as specified hereinbefore. (iii) Sealing the gap of frame with Jamb and Cill (alround) using silicon gel at the rate of 0.05 lit/m for both faces of window. |
| 36 | Dismantling floor, hearth or wall tiling including cement mortar bedding removing serviceable tiles and rubbish off the premises etcand removal of rubbish/ demolished materials out of MD land complete all as specified and directed. |
| 37 | S&F Non Skid (coloured) ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specifed and as directed. |
| 38 | S&F glazed ceramic (coloured) tiles (450mmx 350mmx7 mm) in vertical surfaces such as skirting dados and risers of steps etc set and jointed in neat cement slurry and pointed in white or coloured cement. Including cutting the tiles to the required size wherever required including motering the corners etc over & including 10 mm thick backing coat of cement plaster in CM (1:4) complete all as specified and directed. |
| 39 | Taking up or down steel tubing and connections, 20 mm bore including cleaning for re-fixing complete all as specified and as directed. |
| 40 | Supplying and laying of CPVC pipes SDR 11 20mm & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 41 | M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing, etc., and making good, cutting exc 10 cm but not exc 20 cm girt complete all as specified and as directed. |
| 42 | S&F in repairs vitreous china water closet 'Orissa' pattern of size 580mm X 440mm, white with integral foot rest and 'P' trap(excluding flushing cistern), but including PVC flush pipe and provision of lime concrete bedding complete all as specified and as directed. |
| 43 | S&F in repairs Low level flushing cistern 10 ltr capacity, PVC incl waste pipe, down take pipe, pair of CI brackets and all accessories complete all as specified and as directed. |
| 44 | S&F in repairs vitreous china wash basin, white, flat back, size 580mm X 450mm including CI brackets, 32mm dia brass chromium plated waste fittings with long screwed shanks and fly nuts flanged end bedded in red lead cement and other end fixed with & including cutting for & pinning in end of brackets and 15mm bore long body pillar tap, cast copper alloy fancy type chromium plated, screwed down high pressure complete all as specified and as directed. |
| 45 | S&F in repairs Bib taps long body, fancy type, chromium plated with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed 15 mm bore complete all as specified and as directed. |
| 46 | S&F in repairs Angle cock, cast copper alloy, fancy type chromium plated, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 47 | S&F in repair PVC connections, 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed. |
| 48 | Dismantling of Galvalume/Asbestos sheet roofing any gauge and any thickness including ridge, valley gutter etc. |
| 49 | S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any design/colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws at any height all as specified and as directed. |
| 50 | S&F Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, eyes board etc. fixed with self tapping screws as specified. |
| 51 | S&F 12 mm thick toughned glass shutter of any size (Plain or frosted) fixed with all necessary patch fitting at all corner, with top and bottom pivot, locking arrangement and ball catcher including embosing/ itching of any figure or logo all as directed by Engr-In-Charge. |
| 52 | Supply and fixing in repairs Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frames of doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directionsof Engineer-in-Charge. |
| 53 | M&L for Preparation of old plastered surfaces of walls,Pillars, cornices etc by brooming down with steel wire brush, scraping down smoke shoot, moulds, moss and efflorescent salts and trading oil and greasy spots and Washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of oil bound distemper on the walls, pillars, cornices including touchup putty filling as required incl putting aside the furniture and covering with polythine till the painting work etc. complete all as specified and as directed. |
| 54 | M&L for Preparation of old plastered surfaces of walls,Pillars, cornices etc by brooming down with steel wire brush, scraping down smoke shoot, moulds, moss and efflorescent salts and trading oil and greasy spots and Washing, rubbing down and stopping of distempered and painted surfaces and applying two coat of oil bound distemper on the walls, pillars, cornices including touchup putty filling as required incl putting aside the furniture and covering with polythine till the painting work etc. complete all as specified and as directed. |
| 55 | M&L for complete removal of existing treatment of wall and applying two coat of oil bound distemper, over a coat of primer, over two coat of wall care putty, complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 16, 2026
11:30 IST
Tender Published
Tender notice published.
TodayNov 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 24 daysNov 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender