Tender For Repair To Misc B/R Works In Wsa-Iii And Armoury In Tech Area At Af Stn Ad Ur
Tender Value
48 Lakhs
Estimated cost
Bid Submission
07 Nov 2026
2 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalandhar → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Misc B/R Works In Wsa-Iii And Armoury In Tech Area At Af Stn Ad Ur
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 24-Oct-2026 | Revision in BOQ | BOQ | 07-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of Concrete in ground floors and paving n.exc 15 cm thickness (below or above ground level), cement concrete ( un reinforced), etc complete all as specified and directed. |
| 2 | Taking down cement plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 3 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished fair & even in CM (1:4) mixed without using extra cement or lime complete all as specified and directed.Note:- Rate quoted by contractor Shall be deemed to including necessary scaffolding etc. |
| 4 | M&L for rendering 15 mm thick on fair faces of brick wall or concrete surfaces finished fair & even in CM (1:6) complete all as specified and directed. |
| 5 | M&L for preparation of newly plastered surfaces of wall and applying two coats of OBD over a coat of putty filing including preparation of newly plastered surface of wall ,complete all as specified and directed. |
| 6 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each complete all as specified and directed. |
| 7 | Taking down, Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each but with shutters (without taking off shutters from the frame),etc complete all as specified and directed. |
| 8 | Taking down shutter of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each and removing from site complete all as specified and directed. |
| 9 | Demolition of brickwork built in cement mortar of any specification in any position complete all as specified and directed. |
| 10 | Dismantling of RCC post or struts of any section embedded in concrete or brick work,masonary etc., including taking out embedded portion and making good disturbed ground and its removal to store yard complete all as specified and as directed. |
| 11 | Dismantling barbed wire fencing, any type. Complete all as specified and as directed. |
| 12 | M&L for Restraining and re-securing existing barbed wire of any description including making good staples complete all as specified and as directed. |
| 13 | Dismantling fencing wire mesh, any type . Complete all as specified and as directed. |
| 14 | Fixing only mild steel galvanized wire chain link fencing mesh of any size to any type of standard rails, straining bolts, including provision of binding wire complete all as specified and directed. |
| 15 | Excavation in post holes (or similar holes) each n. exc 0.50 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not. exceeding 25 cm, watering and removing surplus soil to a distance not exc 5.0 m and making good surfaces complete all as specified and as directed |
| 16 | M&L for Mild steel work for posts and struts in fencing includings cutting tops to shaps as directed, drilling holes, notching for wire etc: flat iron fillets (For securing wire mesh etc) incl all necessary drilling bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 17 | M&L for PCC 1:3:6, type C-2, (using 40 mm graded crushed stone aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases complete all as specified and as directed. |
| 18 | M&L for PCC 1:3:6, type C-2, (using 40 mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and as directed. |
| 19 | M&L for PCC 1:3:6, type B-0, (using 12.5 mm graded crushed stone aggregate) as in coping in drains drains complete all as specified and as directed. |
| 20 | Supply only Chain Link MS galvanised fencing ( Dia of wire 4mm) having mesh size of 50x50mm centre to centre complete all as specified and as directed. |
| 21 | M&L for Mild steel screw bolts ( Machine made ) 5 to 10mm dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to fitted with washers and one hexagonal or square nuts exc 5cm but not exc 10cm long fixed complete all as specified and directed. |
| 22 | M&L for Galvanized, two strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossing with and provision of galvanized mild steel wire staples or steel pins etc as directed and specified (Each line to be measured separately). |
| 23 | Supply only Mild Steel Round bars 10 mm dia and over cut to length bent to shape required including cranking, bending, hooking for columns and binding with steel wire (annealed) not less than 0.9 mm dia or securing clips as in line wire for chain link fencing Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde - E-165)all as specified and directed. |
| 24 | M&L for Preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 25 | M&L for Preparation of new steel surfaces not exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 26 | Excavation in trenches n.exc 1.50 m wide and n.exc 1.50m deep in any type of soil complete all as specified and directed. |
| 27 | Returning , filling in including watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed. |
| 28 | Removal of surplus soil to a distance nexc 50 m and depositing where directed at a level nexc 1.5 m above starting point complete all as specified and directed. |
| 29 | M&L for 25 mm thick Sand filling under floors or in foundations including watering and consolidation, Compleate all as specified and directed. |
| 30 | M&L for Brickwork in cement mortor (1:6) with flyash bricks, straight or curved on plan exc 6 m mean radius built in etc complete all as specified and as directed. |
| 31 | M&L for RCC 1:2:4 type B-1 (Using 20 mm graded crushed stone aggregate) as in roof kerb or mud stop, rounded or chamfered edges etc. complete all as specified and as directed. |
| 32 | M&L for cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 33 | Dismantling floor hearth and wall tiling including cement mortar bedding but not backing removeing serviceable tiles to store and rubbish off the permises complete all as specified and directed. |
| 34 | M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick Screed bed or bedding layer of mortar for laying floor finishes in CM (1:6) complete all as specified and directed. |
| 35 | M&L for glazed ceramic, straight cut/joint free,6-7mm thick colored tiles, area of each tile exceeding 0.13 sqm but not exceeding 0.16 Sqm on vertical surfaces such as dado etc over & including 10mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry and pointed in grout of matching shade of tiles, complete all as specified and directed. |
| 36 | M&L for Vitrified coloured Ceramic tiles 9 to 10 mm thick light shade polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. over 15 mm thick screed cement mortar (1:3) and pointed. in white cement with pigment to match the colour of tiles complete all as specified and directed. |
| 37 | M&L for 75 mm thick plain cement concrete (1:4:8) type D-2, using 40 mm graded crushed stone aggregate as in sub base complete all as specified and as directed. |
| 38 | S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 39 | M&L for Machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size ISI mark of 60mm thickness of M-35 Grade complete all as specified and directed. |
| 40 | M&L for Machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size ISI mark of 80mm thickness of M-40 Grade complete all as specified and directed. |
| 41 | M&L for 75 mm thick plain cement concrete (1:2:4) type B-2, using 40mm graded stone aggregate as in sub base complete all as specified and directed. |
| 42 | M&L for 75 mm thick Plain Cement Concrete (1:3:6), type C-2 (using 40mm graded crushed stone aggregate), finished even and smooth as in plinth protrection complete all as specified and directed. |
| 43 | Dismantling of Plain or corrugated steel sheeting, any gauge, hickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 44 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/cladding to wall, fixed with self tapping screws etc.complete all as specified and as directed. |
| 45 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 46 | S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 47 | S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts.posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat ironfillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 48 | S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 49 | S&F Steel windows made of MS sheet 1.25 mm thick box type (primer coated) ERW hollow ‘P’ section of size 60 mm x 25 mm single rebate comprises of skeleton shutter ERW sec 50 x 20 mm & 1 mm thick & openable leaf consisting two Nos sash bars of ‘T’ section 20 x 3 mm complete welded to frame including cutting holes & making good dismantled portion in PCC 1:2: 4 type B1 four Nos for each window including following fitting welded to shutter ;- (a) Hold fast 150 mm long 12 mm x 3 mm made to shape -04 Nos(b) Handle of ‘Z’ section 20 x 25 mm , 100 mm long 01 Nos each leaf.(c) MS tower bolt 150 mm long 02 Nos each leaf.(d) ‘Z’ section 20 x 25 mm , 100 mm stopper-01 Nos each leaf.(e) Cleat 55 mm long of hollow square 15 x 20 x 63 mm welded to hinges-01 Nos per leaf.(f) MS box type hinges of size 75 x 12 mm -02 Nos per leaf.(g) Fabrication & fixing complete. |
| 50 | All as per item No. 49 here-in-before but without sash bars complete all as specified and directed. |
| 51 | S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each complete all as specified and directed. |
| 52 | S&F stainless steel wire cloth 0.63 mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staple complete all as specified and directed. |
| 53 | S&F Factory made PVC solid single door frame (chowkats) of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening all as specified in SSR part-II 2004 Section-8, clause 8B.3 to 8B.3.2 and shown on drawing in SSR complete all as specified and directed. |
| 54 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and a gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site all as specified in SSR complete all as specified and directed. |
| 55 | S & F for 2nd class HW rail and style, thickness of shutters, 30 mm, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, etc complete all as specified and directed. |
| 56 | M&L for preparation of old plastered surfaces of wall and applying one coats OBD including preparation of surface of wall ,complete all as specified and directed. |
| 57 | M&L for preparation of old plastered surfaces of ceiling and applying one coat of OBD including scapping old surface of wall ,complete all as specified and directed. |
| 58 | M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. |
| 59 | M&L for Preparation of old wooden surfaces over 10 cm width or girth and applying one coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. |
| 60 | Cutting opening through brick walls built in cement mortar for making door, window,and other openings complete all as specified and directed. |
| 61 | S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 62 | S&F in repair 300 mm long Stainless steel, sliding door bolt, plate type, with bright bolt not less than 12mm dia with and including bolts and nuts complete all as specified and directed. |
| 63 | S&F 200 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. |
| 64 | S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. |
| 65 | S&F in repair grating doom 100 mm dia with waste hole of stainless steel complete all as specified and directed. |
| 66 | S&F in repair grating doom 125 mm dia with waste hole of stainless steel complete all as specified and directed. |
| 67 | S&F in repair 75mm dia PVC (SWR) pipes single socketed, in any length with or without rubber ring joints, fixed to walls complete all as specified and directed. |
| 68 | S&F in repair for 110 mm dia PVC (SWR) pipes single socketed, in any length with or without rubber ring joints, fixed to walls, complete all as specified and directed.. |
| 69 | S&F in repair PVC (SWR) bends any radius, bore of pipe in 75 mm, complete all as specified and directed. |
| 70 | S&F in repair PVC (SWR) bends any radius, bore of pipe in 110 mm, complete all as specified and directed. |
| 71 | S&F in repair 75mm dia PVC floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed. |
| 72 | S&F in repair Vitreous China wash basin, white, flat back, size 540x400 mm aps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed. |
| 73 | S&F in repair 600 mmx600 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC buildg board or commercial plywood and fixed to wooden plugs with CP brass screws and cup washers complete all as specified and directed. |
| 74 | S&F in repair Vitreous China urinals, Half stall type white flush pipe, grating and Union for discharge pipe.and urinal spreader of PTMT any colour for fixing with 15mm dia pipe complete all as specified and directed. |
| 75 | S&F in repair Vitreous china wash down water closet pan,( pedestal pattern) including PVC sheet cover, jet and connection to drain or out going pipe and to flushing pipe anti-syphonage pipe etc complete all as specified and directed. |
| 76 | S&F in repair toilet paper holder with flat recessed type stainless steel complete all as specified and directed. |
| 77 | S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and guard rail complete all as specified and directed. |
| 78 | S&F in repair health faucet (ABS body) mild steel chromium plated suitable for 15 mmdia pipe with 1.25 metre long flexiable tube and ABS wall hook including making connection and fixed in position complete in all respect as specified and directed. |
| 79 | S&F in repair PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified and directed. |
| 80 | M&L for exterior acrylic emulsion on new wall surfaces in disruptive / camouflaging pattern of six / four shades comporising the following activities due to change of existing colour scheme/pattern complete all as specified and directed:- (i) Preparation of new wall surfaces for height not exceeding 12.00 Mtr.(ii) Applying two coats of water based exterior acrylic emulsion as in base coat.(iii) Applying two coats of exterior acrylic emulsion in disruptive / camouflaging pattern of six / four shades in Tattoos only. (Camouflage pattern shall be approved by Stn Auth). |
| 81 | M&L for exterior acrylic emulsion on old wall surfaces in disruptive / camouflaging pattern of six / four shades comporising the following activities due to change of existing colour scheme/pattern complete all as specified and directed:- (i) Preparation of old wall surfaces for height not exceeding 12.00 Mtr.(ii) Applying two coats of water based exterior acrylic emulsion as in base coat.(iii) Applying two coats of exterior acrylic emulsion in disruptive / camouflaging pattern of six / four shades in Tattoos only. (Camouflage pattern shall be approved by Stn Auth). |
| 82 | M&L for exterior acrylic emulsion on PQC surfaces in disruptive / camouflaging pattern of six / four shades comporising the following activities due to change of existing colour scheme/pattern complete all as specified and directed:- (i) Preparation of old PQC surfaces by mechanised sander having RPM of minimum 1200 having vaccum bag. (ii) Applying two coats of water based exterior acrylic emulsion as in base coat.(iii) Applying two coats of exterior acrylic emulsion in disruptive / camouflaging pattern of six / four shades in Tattoos only. (Camouflage pattern shall be approved by Stn Auth). |
| 83 | S&F in repair PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and directed. |
| 84 | S&F in repair for Bib tap of CP brass, 15mm bore, fency type screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 85 | S&F in repair for 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, but fancy type complete all as specified and directed. |
| 86 | S&F in repair for 15 mm bore Angle stop valve of high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and directed. |
| 87 | S&F in repair for 125 mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass complete all as specified and directed. |
| 88 | S&F 20 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. |
| 89 | S&F in repair for Towel rail, 20 mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs complete all as specified and directed. |
| 90 | Taking up or down existing steel water tubing, 15 mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed. |
| 91 | S&F for Galvanised iron steel water tubing, 15 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed. |
| 92 | Taking up or down existing steel water tubing, 20 mm bore alongwith connections fixed/laid in any situation,complete all as specified and directed. |
| 93 | S&F for Galvanised iron steel water tubing, 20 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed. |
| 94 | S&F ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 20 mm- 210 gms) complete all as specified & as directed. |
| 95 | S&F in repair 3 layered rotational moulded polyethylene water storage tanks, 1000 ltr Capacity (Cylindrical vertical with closed top), including taking down existing water tank & disconnecting old RCC tank, with 20 mm ball valve, epoxy coated aluminum rod, plastic ball etc, hoisted and fixed in position all as specified in SSR Part I complete all as specified & as directed.Make - Polycon/SINTEX/Sheetal or approved |
| 96 | Disconnecting existing 1000 ltr water storage tanks, setting aside for cleaning (cleaning and removing all scale and dirt etc., from tanks and from mouths of circulating pipes), etc. Hoisting if required reconnection and refixing in position complete all as specified and directed. |
| 97 | Disconnecting existing 500 ltr water storage tanks, setting aside for cleaning (cleaning and removing all scale and dirt etc., from tanks and from mouths of circulating pipes), etc. Hoisting if required reconnection and refixing in position complete all as specified and directed. |
| 98 | Rough excavation over existing filling material not exceeding 6.00 metre height from base and disposal of the same upto 50 metre lead at workable location, cleaning the excavated admixture with sieve(s) of size as directed to make the existing mixure free from all vegitation material like bushes, grass, plants and the like including metal pieces and pebbles etc. and transporting the same to originl locations for making embankments complete all as specified and directed.. NOTE: Contractor may use mechanical means (Hydraulic excavator) for this item with prior written approval of Engineer-in-Charge. |
| 99 | M&L for soft/loose soil forming embankments including raising (or lowering) earth.spreading in layer n exc 30cm thick, watering, ramming to obtain optimum moisture conditions to the specified percentage of standard of standard proctor density not less than 95% , and finishing to required sizes shape , etc n. exc 1.5m high from base/GL and incl rough exc over existing filling material not exc 7.5 mt ht including carrying out exacavated soil from out side defence land and filling in traverse, complete all as specified and directed. Note : Rates include cost of earth/soil to be brought from out side the defence land. |
| 100 | ditto- but hight exc 1.5 mtr to 3 mtr |
| 101 | ditto- but hight exc 3 mtr to 4.5mtr |
| 102 | ditto- but hight exc 4.5 mtr to 6 mtr |
| 103 | ditto- but hight exc 6 mtr to 7.5 mtr |
| 104 | S&F in repair MS sliding rollers 1 mtr wide having frame made out of MS angle iron 65mmx65mmx6mm, roller made out of GI pipe 60 mm dia heavy grade fixed to frame @ 100mm passing through both sides beraring and axle rod 16mm to 24mm passing through both sides bearing and fixed with frame for smooth sliding of loads including dismantling of old MS sliding roller complete all as specified and directed. |
| 105 | S&F concertina coil galvanised 60 cm dia (spacing of coil wire @ 20cm c/c) incl securing point in crossing and provn of galvanised mild steel wire staple or steel pin complete all as specified and directed. |
| 106 | Demolition of cement concrete in ground floors and pavings in any thickness (below or above ground level) and removing demolished material from site to a distance exceeding 1.50 km and not exc 5 km and depositing where directed by Engr -in-Charge. |
| 107 | M&L for 10 mm thick sand cushion with clean river sand duly clear of residual, organic and deleterious materials spread evenly to uniform thickness laid over DLC layer as specified and directed (No additionaI amount to be paid for overlap) |
| 108 | Supplying and laying 400 micron thick HOPE shee (Virgin Quality) water proof, wrinkle free without puncture having minimum weight 390 gm/Sqm ave tack coausand cushion as specified in the design with overlap between adjacent strips and a transverse joints as minimum 300mm complete all as specified and directed. |
| 109 | M&L for 250 mm thick cement concrete work in pavemenet /hard standing or flexural strength 40 kg/ per sqcm in field using 400 kg of cement per cum, spread and compacted by using neredle and screed vibrator and all as specified and incl necessary formwork rounding off edges finishing by brooming / belting cutting etc complete all as specified and directed. |
| 110 | Forming dummy/contraction joint with an initial saw cut of 3 mm soon after the concrete has set, upto a depth of 1 J3rd to 1 /41h the thickness of the slab widening the first saw cut to 6 mm and 24 mm deep by using diamond bit cutter of appropriate size straight and smooth edges Joint cleaned thoroughly with application of compressed air. Joint shall be made dry, vacuum cleaned and free of dirt, oil vegetation and other debris. Application of two coats of primer with thin brush by forward and backward movement at an interval of 30 minutes before placing the backup rod and pouring the sealant. Placing of closed cell, medium density, crossed linked polyethylene foam backup rod of 8 mm dia application of bond breaker tape on top of back up rod for complete width of the joint and filled with polyurethane based sealant complying with BS-5212 , BS 4254 and EN-141875-2003 with minimum movement accommodation factor (MAF) OF +/- 30% having minimum 10 year performance guarantee applying masked tape on the edges of joints and removing the masking tape after filling of sealant as per the method specified by the manufacturer complete as specified and directed. |
| 111 | M&L for exterior acrylic emulsion on PQC surfaces in disruptive / camouflaging pattern of six / four shades comporising the following activities due to change of existing colour scheme/pattern complete all as specified and directed by Engr-in-Charge:- (i) Preparation of New PQC surfaces by mechanised sander having RPM of minimum 1200 having vaccum bag.(ii) Applying two coats of water based exterior acrylic emulsion as in base coat.(iii) Applying two coats of exterior acrylic emulsion in disruptive / camouflaging pattern of six / four shades in Tattoos only. (Camouflage pattern shall be approved by Stn Auth). |
| 112 | Notes: Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 24, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Nov 07, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 2 daysNov 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender