Tender For Iet Lab Equipment
Tender Value
Ref. Documents
Estimated cost
Bid Submission
05 Nov 2026
17 days left
EMD
45000
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Indore → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Iet Lab Equipment
BOQ
| Sl. No. | Item Description |
| 1 | Item Name and Specification |
| 2 | Transmission Line Trainer kita) Coaxial cable: 100m (25m * 4)b) Impedance matching resistances: 0 - 100 Ohms. 2 Nos.c) Test Generators: 1. Sine Wave: 40 KHz - 400 KHz (Low Range) 2. Square Wave: 400 KHz - 4MHz (High Range)d) Interconnections: 4 mm Banana socketse) Test Points: 10 |
| 3 | Digital LCR Metera) Measurement Function Test Parameter: L-Q, C-D, R-Q, |Z|-Q Basicb) Accuracy: 0.2%c) Equivalents circuit: Series, paralleld) Range mode: Auto, Hold Trigger modee) Internal Measurement speed: Fast: 12, Med: 5.1, Slow: 2.5 (meas/sec)f) Correction Function: Open/Short multi frequency Zeroing Measurement |
| 4 | Digital Multimetera) 4000 Counts Large LCD Display with Auto/Manual Rangeb) No Power-OFF under natural operationc) Data Hold, Max. / Min. Value Holdd) Capacitance, Frequency / Duty Cycle, Temperature and transistor Test |
| 5 | Digital Storage Oscilloscope 50MHz, 2 Channela) Real-time sampling rate: 500MS/Sb) Oscilloscope Storage depth: 64kptsc) Waveform capture rate: 5,000wfms/sd) Auto measurement: 34 waveform typese) Peripheral Interface: Standard USB Host, USB Device, EXT Trig, Pass/Fail |
| 6 | Digital Communication Lab |
| 7 | Sampling and Reconstruction Modulea) Crystal Frequency: 8 MHzb) Sampling Frequency: 20, 50, 80, 100, 200 & 400 KHz (switch selectable)c) On-board Generator: Synchronized 1 KHz sine wave (5 V) ppd) Duty cycle: 0 - 90% in Decade steps (switch selectable)e) Low Pass Filters: 2 & 4 order Butterworthf) Filters Cut-off frequency: 3.4 KHz each |
| 8 | TDM Pulse Code Modulation Transmitter Modulea) Crystal Frequency: 16 MHzb) On Board Analog Signal: 2 KHz, 4 KHz (Sine wave synchronized c) to sampling pulse Adjustable amplitude and separate variable DC level)d) Input Channels: 2 nos.e) Multiplexing: Time Division Multiplexingf) Sync Signal: Pseudo Random Sync Code Generatorg) Error Check Code: Off - Odd - Even - Hamming |
| 9 | TDM Pulse Code Modulation Receiver Modulea) Input Channel: Time Division Multiplexed serialb) Input Demodulation: Pulse Code Demodulation Clockc) Regeneration: By Phase Locked loopd) Operating Speeds: Fast - 320 KHz/Channel, Slow 1.9 Hz/Channele) Error Detection (Single bit): Off-Odd-Even parity & Hamming codef) Error Correction: Hamming code |
| 10 | Differential Pulse Code Modulation (DPCM) Moduleg) Functions: Sine and Squareh) O/P frequency range: 300 Hz to 3.4 KHzi) Audio blocks: Audio I/P and O/P processing circuitsj) Control signals: R/W for ADC, reset, Latch enables, OEsk) Sampling frequency: 8 KHz; Bits per sample: 5 bits including sign bit |
| 11 | Linear Block Code Encoder Modulea) Word Length: 4 bitsb) Codeword Length: 7 bits codec) Data Format: NRZ (Not Return to Zero) |
| 12 | Linear Block Code Decoder Modulea) Word Length: 4 bitsb) Codeword Length: 7 bits codec) Data Format: NRZ (Not Return to Zero) |
| 13 | Digital Companding A-law & μ-lawa) Compression and Decompression Techniques: A-Law, ì-Lawb) Signal Generator: Direct Digital Synthesizer Generated Sine wavec) 14 Bit data input through Dip switch.d) SMD LED Indicators: 73nos, for Dip based input data Compressed outpute) Decompressed output Technique selectionf) Crystal Frequency: 8MHz |
| 14 | Microcontroller Lab |
| 15 | Atmega 32 Chip |
| 16 | USB ASP ISP AVR Programmer |
| 17 | Male To Male Jumper Wires 40 Pcs |
| 18 | Male To female Jumper Wires 40 Pcs |
| 19 | Female To female Jumper Wires 40 Pcs |
| 20 | Breadboards |
| 21 | 5mm Red, Yellow, Green LED (Pack of 10) |
| 22 | Rotary Potentiometer 1K Ohm |
| 23 | Resistance, Fixed Resistor, 5 each, 13 values (33ohm, 100 ohm, 220 ohm, 330 ohm, 1 kilo ohm, 2.2 kilo ohm, 3.3 kilo ohm, 4.7 kilo ohm, 10 kilo ohm) |
| 24 | Crystal Oscillator 8 MHz |
| 25 | Capacitor Ceramic (pack of 25) |
| 26 | Rotary Potentiometer 10K Ohm |
| 27 | MQ-02/05 |
| 28 | IR Sensor module |
| 29 | PIR Motion Detector HC SR501 |
| 30 | Heartbeat Sensor module |
| 31 | Ultrasonic Sensor module |
| 32 | Gyro Sensor |
| 33 | Color Sensor |
| 34 | pH Sensor |
| 35 | Soil Moisture Sensor |
| 36 | LM35 Temperature Sensor |
| 37 | DHT11 temperature and Humidity Sensor |
| 38 | LCD 16X2 |
| 39 | Motors (Servo, DC, Stepper) with driver IC |
| 40 | DC motor fan |
| 41 | IoT Lab Item |
| 42 | Raspberry Pi 3 B+ |
| 43 | Video Capture Card (For use in laptops) |
| 44 | HDMI Cable |
| 45 | Keyboard |
| 46 | Mouse |
| 47 | Esp32 |
| 48 | Micro USB Cable (for ESP 32) |
| 49 | MQ-02/05 |
| 50 | IR Sensor module |
| 51 | PIR Motion Detector HC SR501 |
| 52 | Heartbeat Sensor module |
| 53 | Ultrasonic Sensor module |
| 54 | Gyro Sensor |
| 55 | Color Sensor |
| 56 | pH Sensor |
| 57 | Soil Moisture Sensor |
| 58 | LM35 Temperature Sensor |
| 59 | DHT11 temperature and Humidity Sensor |
| 60 | LCD 16X2 |
| 61 | Motors (Servo, DC, Stepper) with driver IC |
| 62 | DC motor fan |
| 63 | Antenna Engineering Lab |
| 64 | Antenna Training Setup with Motorised rotating unitMotorised Antenna Unit Plotting Software with 22 Antennas. Micro-controller Based High Precision DC Stepper Motor. Automatic Zero Point setting.Built-in DC Power Supply Instant Plotting of radiation Pattern with Antenna & Radar Single UserWaveforms: SineRF Generator: 750 MHz approximately (output adjustable)Tone Generator: 1 KHz approximately (output adjustable)Directional Coupler: Forward & Reverse (selectable)Matching Stub: Slider typeAntenna Rotation: 0-360 deg. Resolution 1 deg.Receiving Antenna: Folded dipole with reflectorDetector Display: Level adjustable meterInterconnections: 2 mm Banana socketsProduct Tutorial Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysNov 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender