Tender For Renovation Of The Office Room Of Chief Engineer, Pwd (Water Resource), Kunjaban, Agartala, Including Replacement Of Existing Doors With New Doors, Tiles Work, Installation Of Walling, False Ceiling, Renovation Of Toilet Block, Repairing Of
Tender Value
9.68 Lakhs
Estimated cost
Bid Submission
30 Oct 2026
13 days left
EMD
19368
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of The Office Room Of Chief Engineer, Pwd (Water Resource), Kunjaban, Agartala, Including Replacement Of Existing Doors With New Doors, Tiles Work, Installation Of Walling, False Ceiling, Renovation Of Toilet Block, Repairing Of Plumbing System And Other Allied Works, During The Year 2026-27. Dniet No: 44/Ee/Wrd-Ii /2026-27
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling doors,windowsandclerestorywindows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sqm and below: |
| 2 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :Local Teak Wood |
| 3 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 4 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 5 | Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc. Completei) 300×16 mm |
| 6 | Providing and fixing ISI marked oxidised M.S. Tower bolt black finish, (Barrel type) with necessary screws etc. complete :250x10 mm |
| 7 | Providing and fixing factory made UPVC door frame made of UPVC extruded, section having an overall dimension, as below (tolerance +/- 1mm) with wall thickness 2.0mm+/- 02mm. corners of the door frame to be jointed with galvanized brackets and stainless screws, joint mitred and plastic wilded. The hinge side vertical of the frames reinforced by galvanized MS tube of size 19 × 19 mm and 1 mm +/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-Charge.Extruded section Profile size 48x40 mm. |
| 8 | Providing and fixing to existing door frames.30mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a UPVC profile section of size 30mm x 60mm and wall thickness 2mm ± 0.2mm with inbuilt decorative moulding edging on one side. The styles and rails with plastic brackets of size 75×220 mm mitred and welded at the corners. The styles of the shutter reinforced by inserting galvanised MS tube of size 25×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \\"H\\" Section, a UPVC profile section of size 30×100 mm and 2 mm ± 0.2 mm wall thickness welded to the shutter style with a UPVC profile section single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness with 20 mm panel beading of suitable size/Glass (4 mm thick plain glass)/ louver section, louver frame of suitable size, complete as per manufacturer's specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter). |
| 9 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.Double charged Stainfree vitrified tiles (Glossy)Size of tile 600 mm x 600 mm |
| 10 | Providing and fixing 1st class quality ceramic glazed walltiles conforming to IS : 15622- 2017 (thickness to bespecified by the manufacturer) of approved make in allcolours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12mm thick bed of cement mortar 1 : 3 (1 cement : 3 finesand) jointed with ordinary cement slurry includingpointing with white cement mixed with pigment ofmatching shade etc. all complete as per direction of theEngineer in-charge600 mm X 300 mm in all shades and design |
| 11 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles 300 mm x 300 mm in all shades and designs |
| 12 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board. |
| 13 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 14 | 12 mm cement plaster of mixCement mortar 1:4 (1 cement : 4 fine sand) |
| 15 | 15 mm cement plaster on the rough side of single or half brick wall of mix:Cement mortar 1:4 (1 cement : 4 fine sand) |
| 16 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 17 | Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour [Payment shall be made after submission of Test Certificate issued by the Manufacturer].Two coats |
| 18 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge.(Glazing and paneling and dash fasteners to be paid for separately) :-(A) For fixed portion of approved quality:-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 19 | (B) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and makingprovision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 20 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :-With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 21 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on walli) 15 mm nominal outer dia .Pipes. |
| 22 | ii) 20 mm nominal outer dia .Pipes. |
| 23 | iii) 25 mm nominal outer dia .Pipes. |
| 24 | iv) 40 mm nominal outer dia .Pipes. |
| 25 | Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately) |
| 26 | Providing & fixing false ceiling with SPUF142-D-01 (different design 10 mm thick 150 mm width & necessary length) of approved colour concealed type carrier T section (DWUF:405:40*63.5mm) & L section (DWUF:405:40*48) with necessary screw, holdfast PVC beading & MS black pipe structure 48 mm dia at 1200 mm centre to centre in/c cutting holes & making good the walls complete as per direction of the Eng-In-Charge. |
| 27 | Half brick masonry with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 28 | Distempering with 1st quality acrylic distemper, havingVOC (Volatile Organic Compound ) content less than 50grams/ litre, of approved brand and manufacture,including applying additional coats wherever required, toachieve even shade and colour. [Payment shall be madeafter submission of Test Certificate issued by theManufacturer]Two Coats |
| 29 | Providing & fixing GODREJ SILVER STEEL hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete as selected & approved as per direction of the Eng-In-Charge. |
| 30 | Providing and fixing superior quality Soap dish holder of approved design and colour. (Jaquar make-code-AKP-35731P). |
| 31 | Providing and fixing superior quality towel rail complete with brackets fixed to wooden cleats with C.P. Brass screws with all fittings complete as per direction of the Engineer-in-charge. Towel rail 600 mm long (Jaquar make-code-AKP-35711PS). |
| 32 | Providing and fixing superior quality liquid soap dispenser with glass bottle of approved brand and colour with necessary fittings fixing arrangement complete as per direction of the Engineer-in-charge. (Jaquar make-code-ACN-1135N). |
| 33 | Providing and fixing superior quality toilet roll holder of approved brand and colour with necessary fittings fixing arrangement complete as per direction of the Engineer-in-charge. (Jaquar make-code-ACN-1135N). |
| 34 | Providing and fixing superior quality corner glass shelf with brackets of approved brand and colour with necessary fittings fixing arrangement complete as per direction of the Engineer-in-charge. (Jaquar make-code-ACN-1173). |
| 35 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:893115 mm nominal bore |
| 36 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 37 | Providing fitting and fixing shelf Rack with Greenply 19 mm thick solid boil board, 1 mm thick laminated decorative sheet fixed with marine board, favicol, muskin tap etc. Complete as per direction of the Engineer-in-charge. |
| 38 | Providing and fixing white vitreous china pedestaltype water closet (European type W.C. pan) with seatand lid, 10 litre low level white P.V.C. flushingcistern with manually controlled device (handle lever),conforming to IS : 7231, with all fittings and fixturescomplete including cutting and making good the wallsand floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 39 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the wallswherever require :White Vitreous China Wash basin size 550x400 mm with apair of 15 mm C.P. brass pillar taps. |
| 40 | Providing and fixing magnetic catcher in cupboard / ward robe shutters including fixing with necessary screws etc. (Best make of approved quality) Triple strip vertical type. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender