Tender For special Repairs To Bldg No P-280 Or Line In Zone ‘J At Mil Stn Agartala.
Tender Value
81.67 Lakhs
Estimated cost
Bid Submission
12 Nov 2026
10 days left
EMD
1.47 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
agartala → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repairs To Bldg No P-280 Or Line In Zone ‘J At Mil Stn Agartala.
BOQ
| Sl. No. | Item Description |
| 1 | Taking out complete existing roof treatment from roof surfaces and roughening of surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and removing rubbish at distance not exceeding 50m as per direction of Engineer-in-Charge complete all as specified and as directed t site. |
| 2 | Material and labour for 15 mm thick screed bed or bedding layer in CM 1:4 in order to maintain proper slope over existing roof surface for applying single component acrylic polymer modified, finished even and fair without using extra cement complete all as specified and as directed t site.(Note: Polymeric membrane shall be measured and paid seprately under relevent item of this Schedule 'A') |
| 3 | Material and labour for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in roof kerb, slightly rounded or chamfered on edges, mixed with water proofing compound in top layer as per manufacturer instruction finished even and smooth on exposed concrete surface without using extra cement all complete all as specified and as directed at site.(Note: Liquid WPC shall be measured and paid separately) |
| 4 | M & L for cleaning plastered surfaces to receive the water proofing membrane, applying one coat of hot paving bitumen of penetration value 85/25 conforming to IS 73 @ 1.20 kg/sqm over a coat of bitumenous primer @ 0.30 ltrs per sqm and applying a layers of APP based polymeric membrane, 3mm thick (minimum) weight 3.00 Kg/sqm reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) shall be applied over Bitumenious primer (Application of polymeric memberane shall be by torch sealed application, over laps shall be minimum 100mm on the transverse direction & 75 mm on the longtudinal direction) polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by membrane flashing, coved fillet in PCC (1:2:4) type B-0 of radius 75 mm shall be provided at the junction of roof & other vertical surfaces & surfaces shall be painted with applying one coat of aluminium paint over the APP modified membrane @ 0.11 kg/sqm complete all as specified and as directed at site. |
| 5 | Dismantling of AC sheet corrugated / CGI corrugated sheets in roofing any gauge and any thickness including ridge, valley/gutter etc. complete all as specified and directed at site. |
| 6 | Supply and fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and as directed at site |
| 7 | Supply and fixing pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and as directed at site. |
| 8 | Material and labour for preparation of old steel surfaces over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed at site. |
| 9 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed at site. |
| 10 | S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes cinfirming to IS 1161-1979 grade St -240 with necessary welding and reveting complete all as specified and directed at site. |
| 11 | S&F of FE 290 Gde E-165 for Roof trusses(framed), trussed, purlins, crane gantries, rails and fastening and havy bracket framing (Beam,Tee,angle, channel or flate section) including distance pieces, cleats etc with necessary welding and reveting complete all as specified and directed at site. |
| 12 | Dismantling floor, hearth or wall tiling including cement mortar bedding and removing tiles to store and rubbish off the premises complete all as specified and as directed at site. |
| 13 | Material and labour ceramic coloured tiles 7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.18 Sqm but not exc 0.38 Sqm in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed at site. Note: The colour / shade / design of tiles shall be as approved by AGE(I). |
| 14 | Material and labour ceramic coloured tiles 7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.18 sqm but not exc 0.38 sqm on skiriting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over and including screed bed of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed t site. Note: The colour / shade / design of tiles shall be as approved by AGE(I). |
| 15 | Material and labour for non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match the shade of tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed at site.Note: The colour / shade / design of tiles shall be as approved by AGE(I). |
| 16 | Material & Labour glazed ceramic coloured tiles 450X 300X 7mm thick of premium quality on skiriting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over backing coat of 10mm thick in Cement Mortar 1:3complete all as specified and as directed at site.Note: The colour / shade / design of tiles shall be as approved by AGE(I). |
| 17 | M & L for machine cut Kota stone slab flooring using 20 to 25mm thick slabs, laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:3 complete all as specified and as directed at site. |
| 18 | Material & Labour machine cut kota stone slab as in riser of steps, skirting, dado etc. using 22 to 25mm thick slabs laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish with bee vax polishing all to required sizes, the size and design / pattern of slabs shall be as directed, including borders, margins in two or more shades of slabs over backing coat of 15mm thick in cement mortar 1:6c omplete all as specified and as directed at site. |
| 19 | Material and labour for precast cement concrete chequered tiles of size 300 x 300 x25 mm thick as in floor, set and jointed and pointed with neat cement slurry laid over and including 15 mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed at site. |
| 20 | Material and labour in repair for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:4) complete all as specified and as directed at site. |
| 21 | Taking down cement plaster on brick, concrete surfaces including racking out joints hacking for key, scrubbing down with, water etc complete all as specified and as directed at site. |
| 22 | Material and labour for 15mm thick rendering in CM (1:4) on concrete surfaces mixed with liquid water proofing compound @ 200ml per bag of cement/ as per manufacturer's instructions and finish the surface even and fair complete all as specified and as directed at site.(Note:Water proofing compound shall be measured & paid separately) |
| 23 | Materials and labour for 10 mm thick rendering on other than fair faces of brick work or concrete surface in cement mortar (1:6) and finish the surface even and smooth without using extra cement complete all as specified and as directed at site. |
| 24 | Material and labour for 5 mm thick rendering in CM (1:3) on fair face of concrete surfaces as in ceiling etc finished the surface even and smooth without using extra cement complete all as specified and as directed t site. |
| 25 | Material and labour for preparing newly plastered surface of ceiling, chajjas surfaces and applying three coats of white washing complete all as specified and as directed at site. |
| 26 | Material and labour for preparation of old plastered or unplastered surfaces including brooming down or with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots and applying two coats of white wash on ceilings/chajja complete all as specified and as directed t site. |
| 27 | Material and labour for preparation of newly plastered surface of wall and applying Acrylic Smooth exterior paint (APEX) of required shade ,two coats applied @ 1.67 ltr/10 Sqm over and including priming coat of white cement exterior primer applied @ 2.20 kg/10 sqm on wall surfaces complete all as specified and as directed at site. |
| 28 | M & L for Complete removal of existing treatment of any description on wall surfaces and applying Acrylic Smooth exterior paint (APEX) of required shade in two coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm on wall surfaces complete all as specified and as directed at site. |
| 29 | Material and labour for preparing newly plastered Wall surfaces and applying two coats of Oil Bound Distemper over a coat of white cement primer over a coat of 1 mm thick Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the Wall surfaces complete all as specified and as directed at site. |
| 30 | Material and labour for Complete removal of existing treatment of any description on wall surfaces and applying 1mm thick Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Oil Bound Distemper over one of white cement primer on wall surfaces complete all as specified and as directed at site. |
| 31 | Material and labour for Writing letters or figures [Block, Roman, Italic or Indian] not exceeding 30 cm high with thick paint to stand out boldly and solidly without showing signs of brush marks complete all as specified and as directed at site. |
| 32 | Supply only liquid water proofing compound ISI Marked complete all as specified and as directed at site. |
| 33 | Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover filletscomplete all as specified and as directed at site. |
| 34 | S & F False Ceiling Frame Work using Anodised Aluminium snap grid frame work of 600 X 600 mm panel size for false ceiling with Aluminium \\"T\\" section of size 38 X 25 X 1.50 mm thick for Main Runners, 25 X 25 X 1.5 mm thick for Cross Runners and Angle of size 25 X 25 X 1.50 mm thick along the Walls suspended with and including 6 mm dia, Galvanized mild steel wire (pu to 1200mm length) as in suspenders of ceiling members fixed in proper position with cealing cleats complete all as specified and as directed at site. |
| 35 | Material and labour for 6mm thick prepainted Non asbestos fibre cement building boards (E-board), fixed on aluminium framework with screws complete all as specified and as directed at site. |
| 36 | Material and labour for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed at site.. |
| 37 | Taking down Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each and removing to store complete all as specified and as directed at site. |
| 38 | Supply and fixing 125x60mm size pressed steel, frames 1.6 mm wall thick for door with one or more rebates including necessary fixing lugs, hinges,lock strike plate, etc, complete all as specified and as directed at site. |
| 39 | Material and labour Plain cement concrete in bed block and filling of door frame type B-0 1:2:4 (12.5 mm graded stone aggregate) complete all as specified . |
| 40 | Supply and fixing for 35mm thick factory made flush door shutters solid core construction with block board core and ply wood face panels commercial type on both faces complete all as specified and as directed at site. |
| 41 | Supply & Fixing factory made, 35mm thick, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [a] and fitted to Chowkats complete all as specified and as directed at site. |
| 42 | Cutting holes into brick wall for inserting hold fast & making good dismantled portion in cm (1:3) or PCC (1:2:4) type B1, depth of cutting exe half brick but not exe one brick complete all as specified and as directed at site.Note: Cutting of holes will be carried out by using mechanical means like Groove cutter/ wall chaser. |
| 43 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed at site. |
| 44 | Material & Labour for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth without using extra cement and providing necessary joints 10mm wide to the full depth of PCC at every 3 meters and every change of directions and the joints duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade any penetration and 3 parts of sand [all by weight] complete all as specified and as directed at site. |
| 45 | Taking down chowkat with shutter without taking off shutter from the frame n.exc 1.50 Sqm each complete all as specified and as directed at site. |
| 46 | Supply and fixing factory made Solid PVC door frame of size 50mmX47mm made out of 5mm woodgrain printed PVC sheet reinforced with MS square tube in opening complete all as specified and as directed at site. |
| 47 | Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with Particle Board Core, 28 to 30mm thick [Stiles], with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm plain colour PVC sheet on back face, termite proof, water proof and fire resistant, supplying & fixing in frame at site as per specification & drawing shown on Serial Page No. 181 of MES Schedule Part - II complete all as specified and as directed at site. |
| 48 | Supply and fixing Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised of 100mm size, type B-21 complete all as specified and as directed at site. |
| 49 | Supply and fixing 150mm size extruded aluminium alloy handles, fabricated type anodizedcomplete all as specified and as directed at site. |
| 50 | Supply and fixing 125mm size extruded aluminium anodized alloy handles, fabricated type complete all as specified and as directed at site. |
| 51 | Supply and fixing 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed at site. |
| 52 | Supply and fixing 200mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed at site. |
| 53 | Supply and fixing 100mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed at site. |
| 54 | Supply and fixing Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed at site. |
| 55 | Supply and fixing Butt hinges, mild steel of 100mm size, type B-21 complete all as specified and as directed at site. |
| 56 | Supply and fixing in repairs 25 mm dia Harrison Rails [Curtain Rails], stainless steel, chromium plated with and including fixing of brackets, stops, rollers etc ccomplete all as specified and as directed at site. |
| 57 | S & F in repair Aluminium Powder Coated Three Track (2 glazed & one gauze shutter) Sliding Window Frame (aluminium sections weighing not less than 1.67kg/m for frame) and Shutters (aluminium sections weighing not less than 0.55kg/m for shutter) including necessary Joining Cleats, Glazing Clips, Neoprene Rubber Packing, Powder Coated Aluminium Snap Beading, Screws, Powder Coated Aluminium Fittings such as Locking Arrangement [4 Nos], including glazing with 5.5 mm thick Tinted Glass and aluminium Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium beading and making good the surface complete all as specified and as directed at site.Note: (a)The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I.[b] Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as locks, 5.5mm thick tinted glass and wire cloth etc. |
| 58 | Supply and fixing in repair Powder coated aluminium louvered ventilators of size 600X600mm with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 5.5mm thick frosted tinted glass fixed in panels with suitable locking arrangements and making good the surface complete all as specified and as directed at site.Note: (a)The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I.[b] Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as locks, 5.5mm thick tinted glass etc. |
| 59 | Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.00mm and fixed with stainless steel wire staples complete all as specified and as directed at site. |
| 60 | Material and labour for preparation of steel surface n.exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed at site. |
| 61 | Demolition of Unreinforced Cement Concrete/ Lime concrete of sunken floor (ground or 1st) and removing rubbish to a distance exceeding 150M but not exceeding 250 M complete all as specified and as directed at site. |
| 62 | Material and labour for mass concrete using PCC 1:5:10 type E2, using 40 mm graded stone aggregate as in sunken floor complete all as specified and as directed at site. |
| 63 | Material and labour for 20 mm thick cement plaster in CM 1:4 mixed with Water proofing Compound @ 200ml per bag of cement/ as per manufacturer's instructions on sunken portion to maintain the slop forword spocet pipe with acrylic based polymer modified cementitious composite compound as approved by GE/AGE(I) and applying cement slurry two layers i.e. 1st layer @ 0.488Kg/ Sqm mixed with composite compound @ 0.253 Kg/Sqm & 2nd layer @ 0.242Kg/ Sqm mixed with composite compound @ 0.126 Kg/Sqm and applying 200 micron Polythene Film with adhesivecomplete all as specified and as directed at site.Note: Minimum 4 hours gap for air curing will be maintained between 1st layer and 2nd layer. |
| 64 | Supply and fixing in repairs Vitreous China squatting pan of ‘Orissa pattern’, size 580 mm x 440mm (white) with ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern complete including provision of PCC bedding and connection to trap, flushing pipe, antisyphonage pipe, etc. including making good the disturbed floor complete all as specified and as directed at site. |
| 65 | Supply and fixing in repairs 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed at site. |
| 66 | Supply and fixing in repairs vitreous china WHB of size 450x300mm including waste fittings, brass, chromium plated with long screwed shanks and flynuts, flange end bedded in red lead cement and other end fixed etc complete all as specified and as directed at site. |
| 67 | Supply and fixing in repair low density polythene (LDPE) pipes of pressure rating 6 Kg/Sq cm bore of tube 32 mm for waste pipe of WHB or sinks etc complete all as specified and as directed at site. |
| 68 | Supply and fix in repair PVC connection 15mm size with PTMT nuts of length 600mm ccomplete all as specified and as directed at site. |
| 69 | Supply and fixing in repairs looking mirror of size 600mm x 450mm x 5mm thick bevelled edge of selected quality glass, decorative type mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers with glass self assembly consisting of 5.5 mm thick sheet glass self 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed at site. |
| 70 | Supply and fixing in repairs 15mm bore angular stop valve fancy type,chromium plated , screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed at site. |
| 71 | Supply and fixing in repairs Brass Chromium Plated Tubular Towel Rail, 20mm dia, D Type, 600 mm long between flanges complete all as specified and as directed at site. |
| 72 | Supply and fixing in repairs Soap dish, vitreous China white of approximate size 160 x 160 x 90 mmcomplete all as specified and as directed at site. |
| 73 | Supply and fixing in repairs 50mm bore high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or innfloors etccomplete all as specified and as directed at site. |
| 74 | S & F in repair UPVC Pipe of 20 mm bore, of pressure rating 10 KGf / Sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed at site. |
| 75 | S & F in repair UPVC Pipe of 15 mm bore, of pressure rating 10 KGf / Sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed at site. |
| 76 | Cutting chases, pinning in, making good to facings where required and pointing in CM(1:3) to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick wall ccomplete all as specified and as directed at site. Note: Cutting of walls will be carried out by using mechanical means like Groove cutter/ wall chaser. |
| 77 | Supply and fixing 20 mm bore Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe [Minimum Weight 20mm - 210 Grams] etc. complete all as specified and as directed at site. |
| 78 | Supply & fixing in repairs gun metal globe or gate valve 20mm dia with iron wheel head screwed both ends for iron pipecomplete all as specified and as directed at site. |
| 79 | Supply and fixing in repair 75 mm bore dia PVC (SWR) pipes single socketed, in any length with rubber ring loints, fixed to walls only integral water proofing compoundcomplete all as specified and as directed at site. |
| 80 | Supply and fixing in repair 110 mm bore dia PVC (SWR) pipes single socketed, in any length with rubber ring loints, fixed to walls only integral water proofing compound complete all as specified and as directed at site. |
| 81 | Supply and fixing 110 mm bore PVC (SWR) bends in any types complete all as specified and as directed at site. |
| 82 | Supply and fixing 75 mm bore PVC (SWR) bends in any types with acess doorcomplete all as specified and as directed at site. |
| 83 | Supply and fixing 110 mm bore PVC (SWR) bends in any types with acess doorcomplete all as specified and as directed at site. |
| 84 | Material and labour for preparation of new wooden surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed at site. |
| 85 | Supply and fixing in repair 500 ltrs capacity rotational moulded polythene three layer water storage tanks (Cylindrical vertical with closed top) hoisted & fixed in position complete all as specified and as directed at site. |
| 86 | Supply and fixing in repair 110 mm bore PVC [SWR] Branch Piece, single [Single \\"Y\\"/T] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed at site. |
| 87 | Supply and fixing in repair 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed at site. |
| 88 | Taking down carefully existing copper/Aluminum point wiring (light,socket or power) complete including fittings such as switches, ceiling roses, pendents, sockets, boxes, light fitting etc and removing from site and making good disturbed surfaces of walls, floors etccomplete all as specified and as directed at site. |
| 89 | Material and labour for point wiring , (concealed type) with PVC insulated 1100 volts grade FRLS unsheathed single core multi-stranded copper conducter 1.5 Sqmm (nominal area) for phase, netural and 1.5 sqmm pvc insulated unsheathed multi-stranded copper conducter cable for earth continuty conducter drawn through and including PVC conduit (medium grade) of asquate size with fitting and accessories as required at site including suitable size of GI boxes of thickness not less than 0.8 mmthick and earth continuty conductor shall be connected to common earth and earth dolly for one light/fan point controlled by one way switch complete all as specified and directed at site.NOTE:- (i) Cost of cutting of wall, if any for housing of GI box,ceiling rose,etc and also making god the distrubed surfaces are deemed to be included in unit rate.(ii) CCost of GI box of suitable size shall be deemed to be included in the qouted rate. |
| 90 | All as per item No 95 above but for 3/5 pin, 6 Amp Socket outlet on the same board complete all as specified and as directed at site. |
| 91 | All as per item No 95 above but for 3/5 pin,6 Amp switch Socket outlet on independent board complete all as specified and as directed at site. |
| 92 | Material and labour forpower point wiring , (concealed type) with PVC insulated 1100 volts grade FRLS unsheathed single core multi-stranded copper conducter 2.5 Sqmm (nominal area) for phase, netural and 2.5 sqmm pvc insulated unsheathed multi-stranded copper conducter cable for earth continuty conducter drawn through and including PVC conduit (medium grade) of asquate size with fitting and accessories as required at site including suitable size of GI boxes of thickness not less than 0.8 mmthick and earth continuty conductor shall be connected to common earth and earth dolly for one light/fan point controlled by one way switch complete all as specified and directed at site.NOTE:- (i) Cost of cutting of wall, if any for housing of GI box,ceiling rose,etc and also making god the distrubed surfaces are deemed to be included in unit rate.(ii) CCost of GI box of suitable size shall be deemed to be included in the qouted rate. |
| 93 | Supply & Fixing switch socket combination 2 in 1, 5 pin,5 and 15 Amp flush type complete all as specified and as directed at site. |
| 94 | Supply & fixing switch piano flush type (ISI marked), single pole, one way 5/6 Amp, 240 Volts complete all as specified and as directed at site. |
| 95 | Supply & fixing Switch socket combination 5 pin, 6 Amp flush type universal complete all as specified and as directed at site. |
| 96 | Supply and fixing socket out let, 5 Pin, 6 Amps flush type complete all as specified and as directed at site. |
| 97 | Supply and fixing ir ceiling rose, PVC/polycarbonate, isolated body surface bakelite, 65mm x 50mm, ISI marked three terminals complete all as specified and as directed at site. |
| 98 | Supply and fixing stepped rotary type electronic fan regulator, AC240 voltcomplete all as specified and as directed at site. |
| 99 | Supply and fixing in repair as in MCB DB SPN 12 ways double door, 230 Volts, sheet stell with bus bar, neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall including taking down old unserviceable DB alongwith MCBs complete all as specified and as directed at site. |
| 100 | Supply and fixing in repair MCB 6 - 32 Amps, SP, 240 Volt \\"B\\" series, breaking capacity 10 KA all incomming/ outgoing connection with proper size of lugs complete all as specified and as directed at site. |
| 101 | Supply and fixing in repair MCB 6 - 32 Amps, SP, 240 Volt \\"C\\" series, breaking capacity 10 KA all incomming/ outgoing connection with proper size of lugs complete all as specified and as directed at site. |
| 102 | Supply and fixing in repairs LED street light fitting 35 Watt 230 V AC with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver, including GI Bracket made out of 32 mm bore GI Tube, Medium Grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed at site. Note: Light fitting shall be of PF>0.95 |
| 103 | Materials and labour in repair for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion including taking down old unserviciable earthing setcomplete all as specified and as directed at site.Notes:-(i) Main earthing strip from earth plate electrode to rest point upto length of 7.5 meters length shall deemed to be included in the unit rate quoted against this item. (ii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department. |
| 104 | Material & Labour in repair for sub main wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 4.0 sqmm (Nominal area) drawn through in and including PVC Casing/ Caping with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 4.0 sqmm as earth lead and connected to earth dolly and including taking down old unserviceable sub main wiring of any description, making good to disturbed surfacescomplete all as specified and as directed at site.Note : (i) 3 Runs of 4.0 Sqmm cable and one run of PVC Casing/ Caping shall be measured as one unit length |
| 105 | S&F in repair LED light fitting 1x20W, 220V, AC decorative box type with driver ,holder including LED tube light connecting up with three core flexible ciopper conductor cable of suitable size from ceiling rose complete all as specified and directed at site. |
| 106 | S&F inrepair LED light fitting, 1x10/12w bulk head luminaries, with LED lamp, etc. complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size, including taking down the old unserviceable fitting complete all as specified and directed at site. |
| 107 | S&F in repair for sheet metal encloser single pole and neutral with two pin and earth plug complete with one single pole MCB 20 Amps 240 volt complete all as specified and directed at site. |
| 108 | Taking down ceiling fan carefully of any size from its original position, kept in safe custody and refixing the fan in same position or at new place including cleaning and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm after repair work completed complete all as specified and as directed at site. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender