Tender For Comprehensive Repair And Certain Misc B/R Work In Otm Accn In Zone A Area Under Age B/R-I Under Ge Central) Khadki.
Tender Value
40 Lakhs
Estimated cost
Bid Submission
06 Nov 2026
9 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Repair And Certain Misc B/R Work In Otm Accn In Zone A Area Under Age B/R-I Under Ge Central) Khadki.
BOQ
| Sl. No. | Item Description |
| 1 | NOTE FOR ALL PAINITNG ITEMS :-The following precautionary measures shall be ensured by the contractor during execution of work :- (i) Contractor shall deposit entire quantity of materials (proprietory materials) in sealed containers required for painting works covered under subject contract in the custody of Engineer-In-Charge/ Office in charge of unit.(ii) The materials as required shall be issued to contractor by JE/ Engineer-In-Charge on daily basis and the empty containers/ bags shall be deposited in the store of Engineer -In-Charge by the contractor, for verification as per standard consumption/ coverage prescribed by the manufacturers.(iii) Before applying cement base paint/weather proof acrylic emulsion paint contractor shall use the wire brush for the removal of loose paint, dust, algae, moss and filling of crack using crack sealent and cleaning of surface by spray jet. (iv) Application of cement base paint strictly done by spray/mechanical spray machine only, otherwise 30% cost shall be reecovered from the respective item.(v) After completion of painting work contractor shall remove and clean all the droplets/stain of paint left on the floor, glasses and joinery. |
| 2 | NOTE FOR PLUMBING AND SANITARY ITEMS:-(i) Contractor shall deposit entire quantity of plumbing and sanitary wares materials required / covered under subject contract in the custody of Engineer-In-Charge/ Office in charge of unit. (ii) The materials as required shall be issued to contractor by JE/ Engineer-In-Charge on daily basis.(iii) make specified in BOQ will supersede to all. |
| 3 | Taking down chowkhat or frame n. exc 1.5 Sqm each but with shutter (without taking off shutter from the frame) complete all as specified and as directed. |
| 4 | Taking down chowkhat or frame exc. 1.5 Sqm but n. exc 4 Sqm each but with shutter (without taking off shutter from the frame) complete all as specified and as directed. |
| 5 | Taking down shutter of any description exceeding 1 Sqm but n. exc 2 Sqm each complete all as specified and as directed. |
| 6 | Taking down shutter of any description but exceeding 2 Sqm each complete all as specified and as directed. |
| 7 | Supply and fix 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc complete all as specified and as directed. |
| 8 | Cutting holes in stone / brick walls built in cement mortar for inserting hold fasts measured from face of jambs into wall exc. one brick but n. exc.two bricks &making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specifed and as directed. |
| 9 | Supply and fix mild steel flat iron as in hold fasts fitted to chowkats with nails & welded to angle iron frames complete all as specifed and as directed. |
| 10 | Supply and fix for 35mm thick 2nd class hard wood factory maid plain, framed paneled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm venered partical board with commercial veneering on both side faces. The size of rail and stile as per ISI 1003 (Part-I), kiln seasoned and chemically pressure treated (factory made shutter) complete all as specified and as directed. |
| 11 | Supply and fix for 30mm thick flush shutter, solid core construction, with block board core plywood face panels, commercial type on both sides, chemically treated against termite infestation, complete all as specified and as directed. |
| 12 | Supply and fix for 35mm thick IInd class HW glazed and skelton shutter, wire mesh, open rebated and prepared to receive glass, gauze, etc. (without sach bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge, etc size of shutters including wire mesh as specified in SSR-I, complete all as specified and as directed. |
| 13 | Supply and fix factory made Solid PVC Door Frame of size 50mm x 47mm single revated made out of extruded 5mm plain colour PVC sheet reinforced with M.S. Square tube etc complete all as specified and as directed. |
| 14 | Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame etc complete all as specified and as directed. |
| 15 | Supply and fix, Powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. |
| 16 | Powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws including locking arragement etc. complete all as specified |
| 17 | Supply and fix 4.00 mm thick plain sheet glass, selected quality, in square nexc 0.5 Sqm each pane complete all as specified and as directed. |
| 18 | Supply and fix 4.00 mm thick frosted sheet glass, selected quality, in square nexc 0.5 Sqm each pane complete all as specified and as directed. |
| 19 | Supply and fix Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 20 | Supply and fixing powder coated aluminium door made out of hollow extruded aluminium section as mentioned below. Each door having 02 Nos disc or D type handels, 02 Nos aluminium tower bolts 200 mm size one aluminium sliding door bolt or 250mm size, one brass mortice lock of six levers with key in duplicate regulated by double action hydrolic floor door spring (Make Sandhu/TITZ) shutter to be partly glazed with 5 mm thick tinted glass and partly paneled with 12 mm thick pre laminated particle board fixed with glazing clips, rubber beading/gasket anodized aluminium beading screws complete. Chowkhat Frame : 100.00x44.50x1.20 mm Shutter verticle/stile: 49.90x44.50x1.20 mm Shutter middle rail : 49.90x44.50x1.20 mm Shutter top and bottom rail : 89.50x44.50x1.20 mm MAKE :-(i) Anodized aluminium section : Jindal/Hindalco, Indalco (ii) Particle board : Novapan, Duratuff (iii) Glass : Saint, Gobain, Modi Guard, TATA |
| 21 | Supply and fix powder coated aluminuiim partitions wall including anchorage rod, aluminium cleats, drilling, punching, plastering, and making good to the existing surfaces and comprising of following specification as directed :- (a) aluminium section of size 63.50x38.00x1.20 mm thick (b) 5 mm thick tinted glass with aluminium galzing clips and rubber beads, area not exceedings 1.5 sqm (c) 12 mm thick both side prelaminated particle baord fixed with aluminium clips and rubber beads incl takind down complete all as specified and directed |
| 22 | Supply and fix aluminium louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc incl taking down complete all as specified and directed. |
| 23 | Supply and fix butt hinges, 100mm long, extruded aluminium alloy with galvanised mild steel hinge pin, complete all as specified and as directed. |
| 24 | Supply and fix extruded brass handles, fabricated type polished 150mm long fixing with screws etc complete all as specified and as directed. |
| 25 | Supply and fix Aluminium anodised , barrel tower bolt 200mm long, powder coated of extruded section and fixed complete all as specified and as directed. |
| 26 | Supply and fix Aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy 12mm dia, complete all as specified and as directed. |
| 27 | Supply and fix in repair Aluminium (Die cast) door closure hydrauically regulated, designation, No-2, universal type suitable for door shutter of 701 to 850mm in width and of weight between 36 to 60Kg and fixed, complete all as specified and as directed. |
| 28 | Supply and fix in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed. |
| 29 | Supply and fix for in repair mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. |
| 30 | Material and labour for repairing any type of aluminium/wooden door shutter and refixing in the same opening after resecuring its frame work by means of tightning with new screws of by aluminium angle, cleat and other connected work complete all as specified and as directed. |
| 31 | Supply and fix in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specifed and as directed. |
| 32 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and as directed. |
| 33 | Supply and fix, plain sheet glass 4mm thick, ordinary quality, not exc 0.50 Sqm in each pane fixed to aluminium door/window and steel window/frame with oil putty and securing pins, spring clips etc complete all as specified and as directed. |
| 34 | Taking down mild steel rolling shutters/collapsible steel gate of any size and description, complete all as specified and as directed. |
| 35 | Supply and fix 1.25mm laths thick steel rolling shutters without ball bearing as specified of push pull or manual type as specifed, including top cover, anchoring rod, hasp & staple and one coat of primer and two coat of synthetic enamel paint; erected in position as indicated complete all as specified and as directed. |
| 36 | Supply and fix 1.25mm laths thick steel rolling shutters without ball bearing or gear operated type with bevel gear box and crank handle as specified, including top cover, anchoring rod, hasp & staple and one coat of primer and two coat of synthetic enamel paint; erected in position as complete all as specified and as directed. |
| 37 | Supply and fix collapsible steel gate, top hung, consisting of channel picket, pivoted flat bars, top and bottom runners, brass handle etc, as specified;erected in position and securing runners with holdfast and bracket and one coat of primer and two coat of synthetic enamle paint, complete all as specified and as directed. |
| 38 | Overhauling, servicing and realignment of rolling shutters of area not exc 12 Sqm including replacement of defective bearing and grinding of wheels for smooth movement of shutter, replacement of clamps, bolt, gear box with crank handle etc including cleaning, oiling and greasing of movable parts and welding work all as specified and as directed. NOTE :- (i) Necessary arrangement of crane/moving ladder shall be made by the contractor without any extra cost |
| 39 | Overhauling, servicing and realignment of rolling shutters of area exc 12 Sqm including replacement of defective bearing and grinding of wheels for smooth movement of shutter, replacement of clamps, bolt, gear box with crank handle etc including cleaning, oiling and greasing of movable parts and welding work all as specified and as directed. NOTE :- (i) Necessary arrangement of crane/moving ladder shall be made by the contractor without any extra cost |
| 40 | Material and labour for preparation of new or previously untreated wooden surface of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and a directed. |
| 41 | Material and labour for preparation of new or previously untreated steel surface of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 42 | Dismantling ceiling boards (fibre, pulp, insulation, PVC panelling etc) or insulation boards /slabs/blankets any thickness, including cover fillets complete all as specified and as directed. |
| 43 | Supply and fix Solid PVC wall Lining consisting of 5mm thick wood grain printed /other printed sheet PVC sheet used instead PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed. |
| 44 | Supply and fix 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed. |
| 45 | Taking down steel / iron gates area not exc 10 Sqm each including hold fasts and re-fixing the gates in the same opening including shifting and fixing of existing holdfast in plain cement concrete (1:2:4), type B-1 after raising the gate level including greasing, painting and other necessary minor repairs complete all as specified and as directed. |
| 46 | Supply and fix E-board 'Everest' make 600x600x4mm thick white prelaminated sett embosed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction complete all as directed. |
| 47 | Supply and fix in repair pleated pleased blinds made of polyester fabric with alumnium coating at its back. Pleates of one inch with segments at the interval of not exceeding 100mm top and bottom channels made of aluminium in matching colours. Cord lock and pulleys made of brass, design and type as approved by GE complete all as specified and as directed. |
| 48 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 49 | Material and labour for framed work as in doors or gates of angle or other section (i.e flat/tubular) with gusset plates, rails, braces of Fe-410-W (Gde-E-250) quality-B, etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges/holdfast or steel hanging door fittings in plain cement concrete (1:2:4), type B-1 (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed. |
| 50 | Supply and fix for 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc as per required at site complete all as specified and as directed. |
| 51 | Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles and removing the debris outside the defence land complete all as specified and as directed. |
| 52 | Material and labour Brick work with fly ash old size bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 in any position, complete all as specified and as directed. |
| 53 | Rendering 15mm thick on brick /concrete or dubbed surface in CM 1:4 with water profing compound finishing even & smooth without using extra cement and similar like etc complete all as specified and as directed. NOTE :- Water proofing compound shall be measured & paid separetely |
| 54 | Rendering 15mm thick on brick /concrete or dubbed surface in CM 1:6 with water profing compound finishing even & smooth without using extra cement and similar like etc complete all as specified and as directed. NOTE :- Water proofing compound shall be measured & paid separetely |
| 55 | Rendering 15mm thick on brick /concrete or dubbed surface in CM 1:4 with water profing compound finishing even & smooth without using extra cement and similar like at any height including necessary scaffolding , ladder & formwork including taking down cement plaster, raking out joints, hacking for key & scrubbing down with water and removing the debris outside defence land complete all as specified and as directed. NOTE :- Water proofing compound shall be measured & paid separetely |
| 56 | Material and labour for 15mm thick Rendering on brick /concrete or dubbed surface in CM 1:6 with water profing compound finishing even & smooth without using extra cement and similar like at any height including necessary scaffolding , ladder & formwork including taking down cement plaster, raking out joints, hacking for key & scrubbing down with water and removing the debris outside defence land complete all as specified and as directed. NOTE :- Water proofing compound shall be measured & paid separetely |
| 57 | Supply only Liquid water proofing compound complete etc all as specified and as directed. |
| 58 | Material and labour for preparing new plastered surface of walls and applying two coat of cement base paint over a coat chalk whitening at any height including necessary scaffolding ladder etc complete all as specified and as directed. |
| 59 | Material and labour for preparing new plastered surface of walls and applying two coat of oil bond distemper of alkali resistant primer at any height including necessary scaffolding ladder etc complete all as specified and as directed. |
| 60 | Material and labour for Rendering 10mm thick on concrete surfaces in cement mortar 1:3 finishing even and smooth without using extra cement to RCC ceiling, chhajjas, roof projection, facia,fins,parapet etc. and similar likes upto height 10 mtr including necessary scaffolding, ladder, formwork and including taking down cement/lime plaster of any description including raking out joints hacking for key scrubbing down with water etc and removing the debris outside the defence land complete all as specified and as directed. |
| 61 | Material and labour for preparation of new plastered surfaces of ceiling, chhajjas, roof projection, facia, fins, parapet etc and applying three coats of white wash complete all as specified and as directed. |
| 62 | Material and labour for one coat of synthetic enamal paint of approverd tint over wooden surfaces including preparation of old surfaces over 10 cm width or girth complete all as specified and as directed. |
| 63 | Material and labour for preparation of old plastered or unplastered surfaces of walls and applying one coat of oil bound emulsion distemper of approved tint complete all as specified and as directed. |
| 64 | Material and labour for one coat of synthetic enamal paint of approverd tint on steel surfaces including prepration of old surfaces of any description, over 10cm in width or girth complete all as specified and as directed. |
| 65 | Material and labour for glazed vitrified tiles double charge 7 to 8 mm thick (square/rectangular) polished area of each tile 600mm x 600mm/1200 mm x 600mm over and including 15mm thick screed bed or bedding layer in CM 1:6 for laying floor/wall finishes, set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling and removing the debris outside the defence land complete all as specified and as directed. |
| 66 | Description all as per Ser item No 65 above but in skirting and dado laid over and incl 10mm thick rendering in CM 1:4 and pointing including dismantiling and removing the debris outside the defence land complete all as specified and as directed. |
| 67 | Material and labour for Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm over & including 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes, set and jointed in neat cement slurry and poited in white or coloured cement to match including dismantling and removing the debris outside the defence land complete all as specified and as directed. |
| 68 | Description all as per Ser item No 67 above but in skirting and dado laid over and incl 10mm thick rendering in CM 1:4 and pointing including dismantiling and removing the debris outside the defence land complete all as specified and as directed. |
| 69 | Material and labour for glazed coloured ceramic tiles External/Internal in vertical surface 300mmx600mmx7mm thick over & including 10mm thick rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling and removing the debris outside the defence land complete all as specified and as directed. |
| 70 | Material and labour for machine cut kota stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to mirror finish laid over 20mm thick Screed bed or beddidng layer in CM 1:6 for laying floor finishes including dismantling and removing the debris outside the defence land complete all as specified and as directed. |
| 71 | Material and labour for machine cut kota stone slab in riser of steps, skirting, dado 20-25mm thick over & including 10mm thick rendering in CM 1:4 laid & jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to mirror finish including dismantling and removing the debris outside the defence land complete all as specified and as directed. |
| 72 | Material and labour for cement concrete 25mm thick type B-0, 1:2:4 (12.5mm graded aggregate) as in flooring complete all as specified and as directed. |
| 73 | Material and labour for Granite slab 20mm thick work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, vertical surface of wall also and like in 12mm thick screed bed or bedding layer cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling and removing the debris outside the defence land complete all as specified and as directed. |
| 74 | Supply and fix 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to wall and ceiling or laid in floors including necessary cutting chasing into wall/concelled including taking down old steel tubing etc complete all as specified and as directed. |
| 75 | Supply and fix 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to wall and ceiling or laid in floors including necessary cutting chasing into wall/concelled including taking down old steel tubing etc complete all as specified and as directed. |
| 76 | Supplying and laying 16mm bore of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all required fittings complete all as specified incl cutting chases for concealed water tubing and making good, cutting not exc 10 cm girth on brick masonary surfaces |
| 77 | Supply and fix PVC (SWR) floor trap/Nahani trap, plain with grating including jointing with solvent cement 75 mm dia out let including taking down of old trap & making good the disturbed surface with PCC 1:2:4 or CM (1:3) and SS Grating of any type complete all as specified and as directed. |
| 78 | Supply and fix in repairs for 75mm bore PVC (SWR) pipe single socket in any length with rubber ring joints, laid in trenches, wall, floors or laid in sunken floor etc complete all as specified and as directed. |
| 79 | Supply and fix for 75mm bore PVC bends, branch piece or similar fitting are reqd to make the system functional complete all as specified and as direced. |
| 80 | Supply and fix for PVC floor trap 75mm complete all as specified and as directed. |
| 81 | Supply and fix in repair for 110mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors or fixed on wall etc complete all as specified and as directed. |
| 82 | Supply and fix in repair for 110mm bore PVC (SWR) bends, branch piece or similar fitting are required to make the system functional complete all as specified and as directed. |
| 83 | Supply and fix for 110mm bore PVC (SWR) junction single, (Single T), equal or unequal fitting as reqd to make the system functional complete all as specified and as directed. |
| 84 | Material and labour for disconnecting of existing PVC tank of capacity Exc 250 Ltr & n. exc 500 Ltrs for cleaning including setting aside temporarily and refixing later in same position for water supply to enable water proofing treatement of roof slab beneath the tank in following laid down process all as specifed and directed. (a) Dewatering & removing all settled slit,scale & dust from inside from tanks using coconut brush manually and applying bleaching powder and allowed to rest 1 hour. (b) Cleaning & rinsing the tank using fresh water to wash out complete and allowed to dry for 30 mins. (c) Writing letters of 7 cm height using synthetic enamel paint (white colour) to mention date of cleaning incl rubbing out old letters written over the tank. (d) Re-fixing the tank with fitting as required in same position or raised/lower height after cleaning of water (as may necessary) complete all as specified and as directed. |
| 85 | Material and labour for disconnecting of existing PVC tank of capacity Exc 500 Ltr & n. exc 1000 Ltrs for cleaning including setting aside temporarily and refixing later in same position for water supply to enable water proofing treatement of roof slab beneath the tank in following laid down process all as specifed and directed. (a) Dewatering & removing all settled slit, scale & dust from inside from tanks using coconut brush manually and applying bleaching powder and allowed to rest 1 hour. (b) Cleaning & rinsing the tank using fresh water to wash out complete and allowed to dry for 30 mins. (c) Writing letters of 7 cm height using synthetic enamel paint (white colour) to mention date of cleaning incl rubbing out old letters written over the tank. (d) Re-fixing the tank with fitting as required in same position or raised/lower height after cleaning of water (as may necessary) all as specified and as directed. |
| 86 | Supply and fix in repair for vitreous china squatting pan, orissa pattern, size 580 x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including 'P' or 'S' trap & PVC flushing bend fixed complete all as specified and as directed. |
| 87 | Supply and fix in repairs for vitreous china wash down water closet pan, pedestal pattern, white, including PVC flush pipe fixed complete including connection to existing cistern including 'P' or 'S' trap all as specified and as directed. |
| 88 | Supply and fix in repairs for plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated hinging device any type (as per site requirement any type any size), ISI marked fixed complete all as specified and as directed. |
| 89 | Supply and fix in repairs for vitreous china Urinal, half stall type white standard size (excluding flushing cistern flush pipe and waste pipe ) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing urinal spreader of PTMT any colour, grating and union for discharge pipe fixed complete all as specified and as directed. |
| 90 | Supply and fix in repairs for PVC valveness, symphonic action type, flushing cistern 10 liters capacity, low level, white with inlet ball valve, float and handle including brackets complete all as specified and as directed. |
| 91 | Supply and fix in repairs for PVC waste pipe 32mm dia, complete with 80cm long flexible for WHB/Urinals fixed complete all as specified and as directed. |
| 92 | Supply and fix in repairs for PVC connection 15mm dia and 45cm long with 2 Nos PTMT nuts, fixed complete all as specified and as directed. |
| 93 | Supply and fix in repair for 15mm bore stop valve, cast copper alloy, screwed down,, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and as directed. |
| 94 | Supply and fix in repairs for chromium plated brass single/twoway angle valve for 15mm bore pipe, fixed complete all as specified and as directed. |
| 95 | Supply and fix in repairs bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm bore complete all as specified and as directed. |
| 96 | Supply and fix in repair Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connection and fixed in position complete all as specified and as directed. |
| 97 | Supply and fix in repairs for fancy pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure , with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed for 15mm bore etc complete all as specified and as directed. |
| 98 | Supply and fix in repairs for vitreous china wash basin, white, flat back size 550x400 excluding taps, waste chain and plug and porecelain stopper but including bracket any size and waste coupling of PTMT, including cutting for and pinning in ends of bracket or erecting stand execlusive of fixing of supply and waste pipe etc fixed complete all as specified and as directed. |
| 99 | Supply and fix in repairs for vitreous China table top/Under counter wash basin, white or ivory colour flat back or ovel type, any size excluding taps, waste chain and plug and porcelain stopper but including brackets any size, including cutting for and pinning in ends of brackets or erecting stand stand but exclusive of fixing of suppy and waste pipe etc fixed complete all as specified and directed. |
| 100 | Supply and fix in repair rotational moulded polythylene water storage tanks 1000 liters capacity (three layered), ISI marked cylindrical vertical with closed top including 3 Nos GI check nuts and tank nipple of 20mm bore for inlet and outlet, 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specifed in SSR Part I complete all as specified and as directed. |
| 101 | Supply and fix in repair rotational moulded polythylene water storage tanks 500 liters capacity (three layered), ISI marked cylindrical vertical with closed top including 3 Nos GI check nuts and tank nipple of 20mm bore for inlet and outlet, 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specifed in SSR Part I complete all as specified and as directed. |
| 102 | Supply and fix in repair stainless steel curtain rod with fixing Stainless steel brackets, stops, rollers etc complete all as specified and as directed. |
| 103 | Supply and fix in repairs wall mixer telephonic type chromium plated with CP wall flange complete all as specified and as directed. |
| 104 | Supply and fix in repair for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed. |
| 105 | Supply and fix in repair toilet paper holder of fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed . |
| 106 | Supply and fix in repair stainless steel Soap dish, any type and size, fixed to plugs with chromium plated brass screws complete all as specified and as directed. |
| 107 | Supply and fix in repairs brass chromium plated shower rose 150mm size with swivel joint including fixing to steel pipe 15mm dia fixed in repairs complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender