Tender For special Repair Of Govt Md Accn To Incl Roof Treatment, Floor Tiling, Rewiring, Joinery And Sanitary Fitting And Replacement Of Wall Security Lights At Bldg No P-28 (1 To 8) At Zone-8 Under Age B/R-I & Age E/M Under Ge Babina
Tender Value
49 Lakhs
Estimated cost
Bid Submission
05 Nov 2026
17 days left
EMD
98000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jhansi → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Govt Md Accn To Incl Roof Treatment, Floor Tiling, Rewiring, Joinery And Sanitary Fitting And Replacement Of Wall Security Lights At Bldg No P-28 (1 To 8) At Zone-8 Under Age B/R-I & Age E/M Under Ge Babina
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of PCC/lime concrete (Other than Ground flooors) terracing including felt in any description and in any position over roof etc complete all as specified and as directed by the Engineer-in-Charge. |
| 2 | M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed. |
| 3 | M&L cutting out cracks to 'V' Section in existing roof or terracing, cleaning out, wetting and filling solidly a hot mixture of bitumen and dry sand in proportion of 1:1 by weight complete all as specified and as directed. |
| 4 | Cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed. |
| 5 | M&L, roughening surfaces of old concrete roof by picking ,sweeping clean and washing down with water to remove dust etc and applying a coat of cement slurry @ 3 Kg per Sqm complete all as specified and directed. |
| 6 | M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in coping or roof kerbs on roof chamfered on edge including troweling slightly complete all as specified and as directed. |
| 7 | M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is stil green finished even and fair including mixing of water proofing compound as per manufacturer instruction etc complete all as specified and as directed.Note:- Water proofing compound shall be measured separately as supply only under respective item. |
| 8 | Supply only Liquid water proofing compound complete all as specified and as directed of as per manufacturer instruction. |
| 9 | M&L applying water proofing treatment with the following :-(a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated.(b) After the application of approved bituminous primer the water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyesterd non woven fabric (weight not less then 160gms/sqm) shall be laid on the primed surface by torch application method as per manufactured instruction.(c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membrane.( d ) M&L for preparation of newly surface of APP membrane and applying two coat of bituminous aluminium paint @200 gm /sqm etc complete all as specified and as directed. |
| 10 | Taking up or down existing 15 mm dia bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed |
| 11 | Taking up or down existing 20 mm dia bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed |
| 12 | Supplying and laying of 15 mm dia bore CPVC pipes pittings in trenches/wall complete all as specified. with all fitting SDR-II d ,plain cpvc SDR -II such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed |
| 13 | Supplying and laying of 20 mm dia bore CPVC pipes pittings in trenches/wall complete all as specified. with all fitting SDR-II d ,plain cpvc SDR -II such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed |
| 14 | Fixing only old 15mm dia bore steel tubing and connections obtained from taking down against item No 10 herein before in new or old position fixed to wall, ceiling or laid in floor with new fittings complete all as specified and as directed |
| 15 | Fixing only old 20 mm dia bore steel tubing and connections obtained from taking down against item No 11 herein before in new or old position fixed to wall, ceiling or laid in floor with new fittings complete all as specified and as directed |
| 16 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cuttingexceeding 10 cm but not exceeding 20 cm girth in brick walls complete all as specified and as directed |
| 17 | Dismantling water tanks and removing to store of steel/PVC of capacity exceeding 500 ltr but not exceeding 1000 Ltr complete all as specified |
| 18 | S&F 1000 ltr capacity or rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) ISI marked or make specified, two layered construction hoisted and fixed in position including S&F 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia gi pipe medium grade overflow pipe 600mm long with fitting complete all as specified in SSR Part -I complete all as specified and as directed |
| 19 | S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 210 gms ), complete all as specified and directed |
| 20 | S & F in repair 20mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. |
| 21 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and complete all as specified and as directed. |
| 22 | M&L for screed bed or bedding layer in CM 1:6, 15mm thick complete all as specified and directed. |
| 23 | M & L rendering 10mm thick in cement mortar (1:3) on fair faces of brick work or concrete surfaces as in vertical surfaces for receiving tiles as directed. |
| 24 | M&L for light / (PVGT) ceramic Tiles 7-10 mm thick (square/ rectangular), area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,polished, in floors/Wall etc.jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 25 | M&L for light / (PVGT) ceramic Tiles 7-10 mm thick (square/ rectangular), area of each tile exceeding 0.42 sqm but not exc 1.00 sqm, in dado/Skirting of room & varanada etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed Engr-in-Charge. |
| 26 | M&L for non skid dark shade coloured mate finished ceramic tiles 7 to 8 mm thick (square / rectengular) , in floors of kitchen & bathroom etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed by the Engr-in-Charge. |
| 27 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick in CM(1:6) etc complete all as specified and as directed by tge Engr-in-Charge. |
| 28 | Demolition of PCC in any description and in any position etc complete all as specified at site complete all as specified and as directed |
| 29 | M&L for 75mm thick cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in plinth protection finished even and smooth without using extra cement. The plinth protection grooves shall be made & glass patti should be shall be fix complete as per direction of Engr-in-Charge. |
| 30 | M&L for 40mm thick cement concrete type B2, 1:2:4 (12.5mm graded aggregate) as in floor/ hardstanding finished even and smooth without using extra cement complete all as specified and directed. |
| 31 | Demolition of brick work built in cement mortar complete all as specified and as directed. |
| 32 | M&L brick work with sub class 'B'brick straight or curved on plan exc 6m mean radius built cement mortar 1:4 complete all as specified and as directed |
| 33 | Taking down cement plaster on brick or stone wall including raking out joints, hocking for key scrubbing down with water etc complete all as specified and as directed. |
| 34 | M&L for rendering 10mm thick on fair faces of wall even and smooth finish without using extra cement on conc/brick surfaces in CM 1:6, complete all as specified and as directed |
| 35 | M&L renderig 5mm thick in cement mortar 1:3 on ceiling surface and finished even and smooth with out using extra cment complete all as specified and as directed. |
| 36 | M&L for rendering 15mm thick on fair faces of wall even and smooth finish without using extra cement on conc/brick surfaces in CM 1:4, complete all as specified and as directed |
| 37 | M & L for preparation of new plastered surface and applying three coat of white wash on ceiling complete all as specified and as directed. |
| 38 | M & L for Preparation of new plastered surfaceof wall and applying two coat of OBD paint over a coat of putty complet all as specified and as directed. |
| 39 | M & L for preparation of new plastered surface of wall and applying two coats of exterior wheather proof paint over one coat of putty on external wall surface over a coat of alkali resistant primer complete all as specified and as directed. |
| 40 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exe 1.5 Sqm but n exc 4 Sqm each etc complete all as specified and as directed |
| 41 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exe 1.5 Sqm each complete all as specified and as directed. |
| 42 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 43 | S&F factory madeFactory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 44 | S&F 30mm thick FACTORY MADE half glazed/ Skeleton WIRE MESH SOLID WPC both side Plain DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per S:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. S.S butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares should be fixed with 19*6mm size steel screws etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawings. complete all as specified and directed |
| 45 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.Note: (i) Stainless steel butt hinges 03 Nos with with 32mm long SS screws and Other hardwares should be fixed with 19*6mm size steel screws etc. Note: (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 46 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. Note: Each shutter shiould be fixed with stainless steel butt hinges 03 Nos with 32mm long SS screws and Other hardwares should be fixed with 19*6mm size steel screws etc. |
| 47 | S&F 35mm thick FACTORY MADE WIRE MESH SOLID WPC both side Plain DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per S:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. S.S butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings. complete all as specified and directed. |
| 48 | S&Fstainless steel barrel tower bolts of extruded section & fixed 200 mm long etc complete all as specified and as directed |
| 49 | S&F stainless steel 150 mm handle size etc complete all as specified and as directed |
| 50 | S&F 300 mm long stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or stainless steel complete all as specified and directed. |
| 51 | S&F 300mm, stainness steel ordinary rat tail rod pattern springs (Spring for door) including roller and roller plate complete all as specified and directed. |
| 52 | S&F 150mm, Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 53 | Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in CM 1:3 or cement conc 1:2:4 type B1 as required exc half brick but not exc full brick wall complete all as specified and as directed. |
| 54 | M&L PCC 1:3:6 type C-1 (using 20mm graded stone aggt) as in filling in holes of hold fasts and back filling of chowkats complete all as specified and directed. |
| 55 | M & L Secound class hardwood Plain, solid, straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, all as directed. |
| 56 | S&F in rep 18 mm thick Celuka ply / PVC of grade 1 quality of one side prelaminated and other side plain white or colour to make kitchen cabinet/ drawer shutters complete as per specifications and as directed by the engineer - in - charge.Make:-Rajshri or equivalent |
| 57 | S&F Hasp & staple safety type aluminium anodized with stainless steel hing pin incl bolt to hing plate and fixed with screws 100mm size etc complete. Please Enable Macros to View BoQ information |
| 58 | S&F Hasp & staple safety type aluminium anodized with stainless steel hing pin incl bolt to hing plate and fixed with screws 100mm size etc complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysNov 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender