Tender For Repairing And Renovation Of The Residential Quarters Of Sub-Divisional Judicial Magistrate And Civil Judge (Jr. Div.).
Tender Value
47.56 Lakhs
Estimated cost
Bid Submission
30 Oct 2026
3 days left
EMD
95136
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhalai → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairing And Renovation Of The Residential Quarters Of Sub-Divisional Judicial Magistrate And Civil Judge (Jr. Div.).
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.-All kinds of soil |
| 2 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering --All work upto plinth level: 1:3:6 (1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) |
| 4 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 5 | 80 mm thick factory made c.c. Interlocking paver block of M-35 gradeProviding and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness and size / shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer-In-Charge.a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 6 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of pproved steel primer and two coats of pproved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete as per direction of Engineer-in-charge. G.S.Sheeta) 65 mm |
| 7 | Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. |
| 8 | Providing and laying grading of roof for water proofing treatment complete as required for water proofing treatment complete as required as per direction of the Engineer-in-charge : i) Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 9 | 12 mm cement plaster of mixi) Cement mortar 1:4 (1 cement : 4 fine sand) |
| 10 | 15 mm cement plaster of mixi) Cement mortar 1:4 (1 cement : 4 fine sand) |
| 11 | Dismantling GS sheet roofing including ridges, hips, valleys, gutters wind ties etc. including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50 m etc.complete as per direction of the Engineer- in-charge. |
| 12 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for replastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-Charge. |
| 13 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work (two or more coats) over and including water thinnable priming coat with cement primer. |
| 14 | Finishing walls with water proofing cement paint of required shade of approved brand and manufacture [Payment shall be made after ubmission of Test Certificate issued by the Manufacturer] :New work (two or more coats applied @ 3.84 kg/10 sqm) |
| 15 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (payment shall be made after submission of Test Certificate issued by the Manufacturer):i) Two or more coats on new work |
| 16 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 17 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622-2017, of approved make, in all colour and shade, laid over 230 mm thick cement mortar 1:4(1 cement: 4 fine sand), joiniting with gray cement slurry @ 3.3 kg/sqm in/c grouting the joints with white cement and matching pigments etc all complete as per direction of the Engineer-in-Charge.Glazed vitrified tiles-Full Body(Glossy/Mat Finish/Anti-Skid)Size of Tile 600 mm x 600 mm |
| 18 | Providing and fixing 1st quality ceramic glazed wall tiles (minimum 200 x 300) conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 19 | Providing wood work in frames of doors, windows,clerestory windows and other frames, wrought framed and fixed in position :a) sal wood |
| 20 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters.a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 21 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 22 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :a) 300 x 16 mm |
| 23 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete:a) 250 x 10 mm. |
| 24 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: |
| 25 | Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles for aluminium door with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. |
| 26 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws. |
| 27 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 28 | Providing structural steel work riveted, bolted or welded in built up section, trusses and framed work, in/c cutting , hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 29 | First class brick work in foundation and plinth including cost of all materials as required complete:-a) In Cement mortar 1:4 (1 cement : 4 fine sand) |
| 30 | Providing and fixing water closet squatting pan (Indiantype W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required:White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 31 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid |
| 32 | Providing and Fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :a) Range of three urinal basins with10 litre white P.V.C. automatic flushing cistern. |
| 33 | Providing and Fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. Automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required :a) Single squatting plate with 5 litre P.V.C. automatic flushing cistern. |
| 34 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings:a) Flat back wash basin of size 630x450 mm. |
| 35 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.a) Semi rigid pipei) 32 mm dia |
| 36 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.b) Flexible pipei) 32 mm dia |
| 37 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 38 | Providing and fixing 600x120x5 mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 39 | Providing and fixing heel rest sanitary bend100 mm diaSand cast iron S&S as per IS - 1729 |
| 40 | Providing and fixing double equal junction of required degree with access door,insertion rubber washer 3 mm thick, bolts and nuts complete:a) 100x100x100x100 mmi) Sand cast iron S&S as per IS - 1729 |
| 41 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.a) 100x100x100 mmi) Sand cast iron S&S as per IS - 1729 |
| 42 | Providing and fixing single equal plain junction of required degreea) 100x100x100 mmi) Sand cast iron S&S as per IS - 1729 |
| 43 | Providing and fixing sand cast iron S&S offsets as per IS: 1729a) 152 mm offsetsi) With 100 mm dia. Pipe |
| 44 | Providing and fixing terminal guard:a) 100 mmi) Sand cast iron S&S as per IS - 1729 |
| 45 | Providing and fixing collar:a) 100 mmi) Sand cast iron S&S as per IS - 1729 |
| 46 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter:a) 100 mm |
| 47 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors:a) 100 mm |
| 48 | Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size ) including necessary plaster and pointing in cement mortar 1:4 (1cement: 4 coarse sand):a) 100 mm dia |
| 49 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms |
| 50 | Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms |
| 51 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ ppropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. luminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :- b) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings herever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- i) Anodised luminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 52 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- a) With float glass panes of 4.0 mm thickness (weight not less than 10.0 kg / sqm) |
| 53 | Filling the gap in between aluminium frame and adjacent RCC/brick work by providing weather silicon sealant over backer rod of approved quality etc. complete as per architectural drawing and direction of the Engineer-in charge:- (i) Upto 5 mm depth and 5 mm width. |
| 54 | Providing and fixing stainless steel (SS 304 grade) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in- charge:-a) 255 x 19 mm. |
| 55 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-a) Anodised aluminium of grade AC 15. |
| 56 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement.- All work upto plinth level: i) 1:1½:3 (1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 57 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.a) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 58 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply ncluding all PP - R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc.i) PN- 16 Pipe, 16 mm OD[SDR 7.4] |
| 59 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply ncluding all PP - R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc.ii) PN- 16 Pipe, 20 mm OD[SDR 7.4] |
| 60 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply ncluding all PP - R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc.iii) PN- 16 Pipe, 25 mm OD[SDR 7.4] |
| 61 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP - R plain & brass threaded polypropylene random fittings including trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External workPN-16 Pipe, 32 mm OD (SDR-7.4) |
| 62 | Providing and fixing brass bib cock of approved quality:a) 15 mm dia nominal bore |
| 63 | Providing and fixing brass stop cock of approved quality:a) 15 mm dia nominal bore |
| 64 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):i) 25 mm nominal bore |
| 65 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):ii) 32 mm dia nominal bore |
| 66 | Providing and fixing gun metal non-return valve of approved quality (screwed end):32 mm dia nominal borei) Vertical Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysOct 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender