Tender For Short Term Maintenance Work From Km 598.00 To Km 634.00 Of Nh-31 (New Nh-17) Under Nh Division-Ix In The District Of Jalpaiguri, West Bengal During The Year 2026-27.
Tender Value
5.74 Crore
Estimated cost
Bid Submission
17 Nov 2026
30 days left
EMD
11.48 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalpaiguri → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Short Term Maintenance Work From Km 598.00 To Km 634.00 Of Nh-31 (New Nh-17) Under Nh Division-Ix In The District Of Jalpaiguri, West Bengal During The Year 2026-27.
BOQ
| Sl. No. | Item Description |
| 1 | Road Maintenance (Bill No.01) |
| 2 | Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area. (Reference to MoRT&H's specification clause 201) |
| 3 | Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 (Reference to MoRT&H's specification clause 305).With River Bed Material |
| 4 | Filling Pot-holes and Patch Repairs with open-Graded Premix surfacing , 20mm.Removal of all failed material,in the pavement courses and if necessary below the pavement,until the root causes of the failure is removed, the trimming of completed excavation to provide firm vertical faces; specified for the pavement layer; application of tack coat conforming to cl. 503 of MORT&H's specification, on to the sides and base of excavation prior to placing hot bituminous material as per clause 510 and the compaction,trimming and finishing of the surfaces of all patches to form a smooth continuous surface, level with the surrounding road as per the requirement of clause 3004.2 of MORT&H's specification . |
| 5 | Providing and applying tack coat with Cationic Bitumen Emulsion (RS1) complying with IS:8887 using Emulsion pressure distributor on prepared bituminous/granular surface cleaned with mechnical broom and high pressure air jet at the rate of 0.20-0.30 kg/sqm .(Reference to MORT & H's Specification clause 503). |
| 6 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511) iv) Case- IV: Type B Providing and laying of premix sand seal coat with bitumen emulsion of suitable approved grade. |
| 7 | Fog Seal : This work shall conform to the requirements of cl. 513 of these specifications and shall consist of an application of Emulsified bitumen, without any aggregate cover for sealing fine hair-cracks or for rejuvenating oxidised bituminous surfaces. Areas having cracks with less than 3mm width shall be considered for this treatment, unless otherwise instructed by the Engieer-in-Charge (Reference to MORT&H's specification 3004.3.2). |
| 8 | Road Property Maintenance (Bill No. 2) |
| 9 | Providing and fixing Retro Reflectorised cautionary mandatory and informatory sign as per IRC 67 made of intensity grade sheeting vide clause 101.3 fixed over aluminium sheet 1.5 mm thick supported on mild steel angle Iron post 75 mmx75mm x 6 mm finally fixed to the ground by means of properly designed foundation with M15 grade concrete 45 cmx45 cmmx60 cm , 60 cm below the ground level as per approved drawing (Reference to MORT&H's specification 801). |
| 10 | Providing and erecting direction and place identification retro reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing (Reference to MORT&H's specification 801). |
| 11 | Supplying & fixing of Raised Pavement Markers/Road Studs/Cats Eye made of polycarbonate moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face which shall support a load of 3635 kg tested in accordance to ASTM D 4280 Type H and compling to Specifications of Category A of MoR&TH Circular No. RW/NH/33023/10-97 - DO III Dt. 11.06.1997 & MoRT&H's specification for Road &Bridge Works (Fifth Rev.). Marker height shall not be less than 10 mm and shall not exceed 20 mm, width shall not exceed 130mm and with minimum reflective area of 13 sqcm on each side and slope to the base shall be 35 ± 5 degree. Fixing will be without nails but by using epoxy resin based adhesive as per manufacturer's recommendation including site clearence etc and complete as directed by the Engineer in Charge.The contractor will have to provide a test certificate from a reputable national/international laboratory comforming the above specifications. |
| 12 | Supplying & fixing of Hazard Markers of size : 30cm X 90 cm as per IRC :79-1981 (The above is inclusive of vertical post) |
| 13 | Supplying and installation of delineators(road way indicators,hazared markers, object markers),80 -100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80 X100mm rectangular or 75 mm dia circular recflectorrised pannel at the top buried or pressed into the ground and conformining to IRC 79 and the drawing ( referance to MORT&H's specification 806) |
| 14 | Road marking with hot applied thermoplastic compound with reflectory glass beads on bituminous surface providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gm per squre metre area thickness of 2.5 mm in exclusive of surface applied glass beads as per IRC:35.The finished surface to be levelled uniform and free from streaks and holes.(Reference to MORT&H's specification 803). |
| 15 | Painting Two Coats on New Concrete Surfaces: Painting two coats, after filling the surface & applying a sealing primer, with synthetic enamel paint in all shades on new plastered concrete surfaces as per MORT7H's specification 803.6.2.(Reference to MORT&H's specification 803). |
| 16 | Construction of Reinforced Cement Concrete Railing of M-30 Grade in -situ with 20 mm nominal size aggregate,true to line and grade, tolerence of vertical RCC post not to exceed 1 in 500, centre to centre to space between vertical post for expansion, complete as per approved drawings and Technical Specifications (Reference to MORT&H's specifications 2703, 1500, 1600 and 1700). |
| 17 | Pevment Repairs (Bill No. 3) |
| 18 | Providing and applying tack coat with Cationic Bitumen Emulsion (RS1) complying with IS:8887 using Emulsion pressure distributor on prepared bituminous/granular surface cleaned with mechnical broom and high pressure air jet at the rate of 0.20-0.30 kg/sqm .(Reference to MORT & H's Specification clause 503). |
| 19 | Filling Pot Holes with Bituminous Macadam using Mobile Hot Mix plant (6-10 TPH) with approved crushed aggregates of specified grading premixed with bituminous binder @3.4% by wt. of the total mix, transported to site and laid in the pot hole prepared before hand by cutting the edges to get a firm vertical face and by removing all the failed and loose materials including dust and applying tack coat evenly on the sides and on the surface as per specification, rolling the filled depression with 8-10 tonne smooth wheeled roller to achieve the desired compaction, including the cost and carriage of stone aggregates and bitumen, hire charges of machinery and equipment, cost of fuel and lubricants and wages of all operational staff, quality control except the cost of tack coat complete as per direction of Engineer-in-charge. Payment to be made on the basis of the loose net volume of the stone aggregates used in the work |
| 20 | Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using. Type A and B seal coats (Reference to MORT&H's specification clause 511) iv) Case- IV: Type B Providing and laying of premix sand seal coat with bitumen emulsion of suitable approved grade. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 30 daysNov 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 38 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender