Tender For special Repair Of Bldg No D/1/395, D/1/402, D/1/403 And D/1/394 At Northern Pocket Of Pms Under Ge Panagarh
Tender Value
42.23 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
5 days left
EMD
84500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Bldg No D/1/395, D/1/402, D/1/403 And D/1/394 At Northern Pocket Of Pms Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground (level) and lowering if necessary, removal of the rubbish off the premises complete all as specified and directed. |
| 2 | M & L for 75 mm thick Cement concrete type D2, 1:4:8 (using 40mm graded aggregate) as in sub base, sub floors etc complete all as specified and as directed. |
| 3 | M & L for Cement concrete 75 mm thick type B- 1, 1:2:4 (20 mm graded aggregate) laid on concrete floors and pavings; laid over cement concrete subfloors etc. and finished to an even and rough surface with nominal reinforcement, complete all as specified and as directed by Engg-in-charge. (Note: Reinforcement will be measured and paid separately) |
| 4 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, flat or curved incl ridges hips valleys as in roof coverings complete all as specified and directed. |
| 5 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed |
| 6 | S&F wind ties for roof including securing bolts, flat iron fillets(for securing weather boarding with screw bolts and nuts) includingall necessary drilling or riveting etc and similar work fonforming to Fe 410-O or Fe-310-O including painted with one soap coat of zinc cromate primer paint (including prepration of surfaces at contractor's workshop before fabrication) |
| 7 | Dismantling wall and ceiling board of any descrition complete all as specified and directed. |
| 8 | S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified. |
| 9 | S & F Anodised powder coated aluminium snap grid frame work for false ceiling (size of grid 605x605 mm ) all as specified. |
| 10 | S & F Non asbestos fibre cement designer building boards 6 mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws in ceiling complete all as specified. |
| 11 | Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc all as specified. |
| 12 | M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 13 | Supply only liquid Water proofing compound complete all as specified and directed. |
| 14 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfacescomplete all as specified and directed. |
| 15 | M&L for rendering 15 mm thick in CM 1:6 on other fair faces of brick work surfaces finished fair and even complete all as specified and directed. |
| 16 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified and directed. |
| 17 | Dismantling wrought iron or mild steel work of any description not otherwise provided, for rusted members of steel trusses/ purlins, complete all as specified and directed. |
| 18 | S & F mild steel as Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. all as specified and as directed. |
| 19 | M&L for complete removal of existing treatment of old steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide zinc chrome primer including necessary preparation of surfaces complete all as specified and directed. |
| 20 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 21 | S&F in repairs sheet glass 4 mm thick ordinary quality and glazing with rubber gasket and pin in square n.exc 0.50 sqm in each pan complete all as specified and directed. |
| 22 | S&F in repairs sheet glass 4 mm thick ordinary quality and glazing with rubber gasket and pin in square exc 0.50 sqm in each pan complete as directed. |
| 23 | S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned stacks or galvanised wire staples, complete all as specified and as directed. |
| 24 | Demolition of brick work built in CM including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removal of the rubbish off the premises all as specified and directed. |
| 25 | M&L brick work with fly ash old sized bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 all as specified as directed. |
| 26 | M&L for brick work with flyash bricks straight or corve on plan to any radius as in half bricks thick walls, built in cement mortar (1:4) complete all as specified and directed. |
| 27 | M&L for cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) in surface channels and drains for benching complete all as specified and directed. |
| 28 | M&L for forming fair finish drain channel upto 30 cm inner grith in cement concrete using extra cement complete all as specified and directed. |
| 29 | M & L for Mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 30 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 31 | M & L for light shade vitrified ceramic tiles 10mm thick (square /rectangular ) polished , area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed flush in white or colour cement with pigment over and including 15mm thick cement mortar 1:6 screed bed complete all as specified. |
| 32 | M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including C:M (1:3) back coat of mortar 10 mm thick for laying skirting/dado's wall tiles complete all as speciified and directed. |
| 33 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed. |
| 34 | M&L Machine cut kota stone slab flooring 20-25mm thick over 20mm cement screed base of CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 35 | M&L Machine Cut marble slab (Udaipur Green) 18-20mm thick table rubbed and polished as in window cill. kitchen slab etc. over and including Screed Bed or Bedding Layer 20mm thick in Cement Mortar (1:6),including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and as directed by Engr-in-Charge. |
| 36 | Taking down chowkats or frames with shutter w/o taking off shutter from the frame n exc 1.5 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed by Engr-in-charge. |
| 37 | Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 Sqm & n. exe 4 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge. |
| 38 | S&F Factory made single extruded WPC ( Wood polymer composite) solid door/window and others frames/chowkhat of size 45 x 75 mm double shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS Screws having minimum frame density of 750kg/cum and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engg-in-charge. |
| 39 | S&F Factory made single extruded WPC ( Wood polymer composite) solid Plain flush door shutter of 30 mm size comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives having minimum density of 650kg/cum and with property of being termite/borerproof,water/moisture proof and fire retardent and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws complete as per direction of Engg-in-charge. |
| 40 | S&F factory made single extruded WPC ( Wood polymer composite) 30 mm thick glazed and skeleton panelled door shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade ), calcium carbonate and natural fibres and non toxic additives having minimum density of 650kg/cum and with property of being termite/borerproof,water/moisture proof and fire retardent and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws complete as per direction of Engg-in-charge. |
| 41 | S & F Floor door stopper 150 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 42 | S & F 300 mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy and fixed complete all as specified and directed. |
| 43 | S&F, door closer aluminium (extruded section) body, hydraullically regulated, designation No.2, universal type, suitable for door shutters and weight between 36 to 60 kg and fixed complete all as specified and as directed. |
| 44 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including Aluminium snap beading for glazing/ paneling, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 45 | S & F powder coated Anodised aluminium window shutters, sliding type without sash bars, (minimum thickness of powder coating 50 micron) for three track shutters of windows & ventilators aluminium sections weighing 0.55 kg/m including necessary joining cleats , Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, anodised aluminium fittings suitaible etc all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 46 | M&L for framed work such as grills etc with endsof bars shouldered nd or riveed or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed. |
| 47 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified |
| 48 | S & F 100 mm size butt hinges extruded aluminium alloy with galavanised mild steel hing pin anodised and fixed type C-21 complete all as specified and directed. |
| 49 | S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed. |
| 50 | S&F aluminium handles, cast type, anodised 150mm long complete all as specified and directed. |
| 51 | S & F in repair MS PVC coated drepery rods of 25 mm dia as in curtain rods complete all as specified and as directed. |
| 52 | S & F in repair MS PVC sheeted/powder coated bracket size 150 mm made to shape suitable for holding curtain/drapery rod of 25 mm dia fixed with PVC rawl plugs and MS steel screws for single/double rods complete all as specified and as directed. |
| 53 | M & L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed. |
| 54 | M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M- 35 Grade with grey cement and pigments complete all as specified and directed. |
| 55 | S&F in repairs PVC (SWR) pipes of 75 mm bore diameter single socketed, in any length with rubber ring joints, laid in trenches or in floors. |
| 56 | Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified. Please Enable Macros to View BoQ information |
| 57 | Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender