Tender For Provn Of Flooring, Door Windows (Aluminium And Upvc), False Ceiling In Main Office And special Repair Of Hardstanding Near Bldg No D/1/482 At Pms Under Ge Panagarh
Tender Value
49.97 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
16 days left
EMD
99950
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Flooring, Door Windows (Aluminium And Upvc), False Ceiling In Main Office And special Repair Of Hardstanding Near Bldg No D/1/482 At Pms Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of Stone slabs and tiles of any description or thickness in floors laid in dry and ponted etc. complete all as spd and directed. |
| 2 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for drain work and removal of rubbish off the site complete all as specified and directed. |
| 3 | M & L for excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and as directed. |
| 4 | Removing excavated soil to a distance not exc.50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and as directed. |
| 5 | S&F for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as spd and directed. |
| 6 | S&F for solid PVC Wall Lining consisting of 5mm thick single side prelam colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as spd and directed. |
| 7 | M&L for 25 mm thick PCC 1:2:4 type B-0 (Using 12.5mm graded crushed stone aggregate) as in floor, finished the surfaces fair & even to receive floor finishes, complete all as specified and directed. |
| 8 | M&L for Glazed ceramic designer coloured tiles 8 to 10 mm thick (Square/rectangular) area of each tile exceeding 0.38 sqm but not exceeding 1.00 sqm on wall etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM 1:3 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed. |
| 9 | M&L Virified Ceramic tiles light shade 7- 8 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 10 | M&L Virified Ceramic tiles drak shade 7- 8 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, on vertical surface such as skirtings etc. set and jointed in cement slurry over 10 mm thick rendering in CM 1:4 complete all as specified and directed.complete all as spd and as directed. |
| 11 | M&L for brick work with old size fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 all as specified as directed. |
| 12 | M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished fair and event (including as in patches also) complete all as specified and directed. |
| 13 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer over plastered surfaces of walls complete all as specified. |
| 14 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 15 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 16 | M&L for forming jambs in Cement mortar 1:4 to openings (to foregoing item) including cutting, toothing and properly bonding into old work. also facing, jointing and pointing to match existing work, complete all as specified and as directed by Engr-in-Charge. |
| 17 | M&L for framed work such as grills etc with ends of bars shouldered nd or riveed or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed. |
| 18 | S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty. |
| 19 | M&L for Green marble work 15 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following typesnt with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 15mm thick Screed bed or backing coat for laying floor finishes in CM 1:6 complete all as specified. |
| 20 | S&F for powder coated aluminium snap grid (Size-605mmx 605mm) frame work for false ceiling complete all as spd and directed. |
| 21 | S&F hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. complete all as spd and directed. |
| 22 | S&F for 4mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws as in ceiling complete all as spd and directed. |
| 23 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 24 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, locking arrangement ,C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 25 | M&L 4mm thick any colour ACP board (Aluminium composite panel), exterior grade, (approved colour) fixed with aluminium tapperd clip to aluminium frame work all as specified and as directed. |
| 26 | S&F for stainless steel entrance main glass door pipe pull handle (length 18\\", hole to hole size 14\\" ) with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, with suitable arrangement complete all as specified and directed |
| 27 | S&F for 4mm thick sheet glass, ordinary and glazing with aluminium beading in aluminium frame in square exc 0.5 sqm in each pane all as specified and as directed. |
| 28 | Rolling and consolidating formation surfaces in cutting with power roller exc 8 tonne and n.exc 12 tonne complete all as specified and as directed. |
| 29 | M&L for pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n. exc 10cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge. |
| 30 | M & L and compacting 150 mm thick (compacted thickness) granular sub base course (GSB) grading as per grade I as specified Table 400-1 of MoRTH specification for road and bridge work 2013 in two equal layer over compacted subgrade with natural sand crushed gravel, crushed stone, crushed slag or combination as per the grading required. The materials are mechanically mixed, spread and levelling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100 KN static weight for achieving required compaction density of atleast 98% of maximum dry density. Consolidating to required gradient and camber complete all as specified and directed with finished surface tolerances as per table 900-1 of MoRTH specification for road and bridge works 2013 complete all as specified and as directed by engineer in charge. |
| 31 | M&L for providing and laying factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves, including making drainage opening wherever required complete all as specified and as directed. |
| 32 | M & L for PCC type C2 1:3:6 using 40 mm graded aggregates as in foundations, fillings and mass concrete. |
| 33 | M & L for Sand filling under floors or in foundation including watering and consolidation. |
| 34 | M & L for Machine pressed precast concrete coloured interlocking paver block, pre-polished any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and pigments complete all as specified and as directed. |
| 35 | M & L for applying 02 coats of synthetic enamel paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces incl preparation of newly plastered surfaces of concrete. |
| 36 | M & L for PCC type D2 1:4:8 using 40 mm graded aggregates as in foundations ,fillings and mass concrete. |
| 37 | M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 38 | M&L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.as specified & directed by Engr-in-Charge |
| 39 | M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200m thick (Horizontal or sloping). |
| 40 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysNov 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender