Tender For Repair To Compound Wall, Fencing And Main Entrance Gates At Site ‘A Of Naval Base Area Karwar.
Tender Value
49.90 Lakhs
Estimated cost
Bid Submission
04 Nov 2026
17 days left
EMD
99800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Uttara Kannada → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Compound Wall, Fencing And Main Entrance Gates At Site ‘A Of Naval Base Area Karwar.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of concrete block walling, brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed. |
| 2 | Dismantling of stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed. |
| 3 | M&L for providing precast cement concrete block masonry with solid blocks exceeding 10 cm width, type C-1 (1:3:6) using 20 mm graded aggregate and set in cement mortar (1:6), complete all as specified and directed. |
| 4 | M&L for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6, complete all as specified and directed. |
| 5 | M&L for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6, but except stones, complete all as specified and directed. |
| 6 | M&L for flush pointing to block in course or ashlar masonry or concrete block walling in CM 1:4 complete all as specified and directed. |
| 7 | M&L for rendering 15 mm thick in cement mortar (1:4) on fair faces of concrete surfaces, finished even and smooth without using extra cement, including necessary scaffolding and safety measures, complete all as specified and directed. |
| 8 | M&L for preparation of new plastered/decorated wall surfaces and applying two coats of acrylic emulsion exterior grade paint by using mechanical spray (maximum working pressure of 3300 PSI) over a coat of primer, including necessary scaffolding and safety measures, complete all as specified and as directed by the Engineer-in-Charge. |
| 9 | Demolition of cement concrete (unreinforced) in ground floors and paving's not exceeding 15 cm thickness, below or above ground level, complete all as specified and as directed. |
| 10 | M&L for plain cement concrete (1:4:8), type D-2, using 40 mm graded stone aggregate, as in foundations and mass concrete, complete all as specified and directed. |
| 11 | M&L for 75 mm thick PCC (1:3:6), type C-2, using 40 mm graded stone aggregate, as in hardstanding/plinth protection, finished even and smooth without using extra cement, complete all as specified and directed. |
| 12 | Dismantling of wrought iron or mild steel work of any description, not otherwise provided for, complete all as specified and as directed. |
| 13 | S&F framed work as in doors or gates of angle or other sections with gusset plates, rails, braces etc., complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including hooks and hinges or steel hanging door fittings (excluding steel sheeting or other covering, running rails and guides), including hanging, fastening and fixing, conforming to Fe-410-W (Grade E-250), complete all as specified and directed. |
| 14 | Taking down steel gates, each leaf area exceeding 1.5 sqm but not exceeding 4 sqm, with bed blocks, pintle hinges and holdfasts; rectifying defects such as straightening, welding etc., and refixing in position with provision of bed blocks, new/old pintle hinges and holdfasts as required, complete all as specified and directed. Note: Welding, bed blocks, pintle hinges and holdfasts will be measured and paid for separately under respective items. |
| 15 | M&L for PCC 1:2:4 type B1, using 20 mm graded stone aggregate, as in bed blocks, including necessary formwork for embedding holdfasts, complete all as specified and directed. |
| 16 | S&F mild steel 0.63 mm thick plain black sheet in steel gates, cut to size, punched, including round-headed screws, clout nails or rivets, and fixed to steel frame with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc., complete in repairs all as specified and directed. |
| 17 | M&L for spot welding exceeding 2.5 cm but not exceeding 5 cm in length, thickness of metal to be welded exceeding 6 mm but not exceeding 9 mm, complete in repairs all as specified and directed by the Engineer-in-Charge. |
| 18 | M&L for stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required), and fitting the same with necessary stainless steel nuts and bolts, complete, including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete in repair all as specified and directed. |
| 19 | M&L for preparing new steel surfaces of any description exceeding 10 cm in width or girth, and applying two coats of synthetic enamel paint by using mechanical spray (maximum working pressure of 3300 PSI) over one coat of red oxide zinc chromate primer, complete all as specified and directed. |
| 20 | M&L for preparing old steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint by using mechanical spray (maximum working pressure of 3300 PSI) over one coat of Red oxide, zinc chrome primer complete all as specified and directed. |
| 21 | Dismantling post or struts including GI barbed wire ( wood, steel or RCC) from natural ground any section including taking out embedded portion and making good disturbed ground complete all as specified. |
| 22 | Dismantling fencing wire mesh any type complete all as specified and as directed. |
| 23 | Excavating in post holes (or similar holes) each n exc. 0.4 cum. in hard / dense soil and getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm etc complete all as specified and directed. |
| 24 | M&L for PCC (1:3:6), type C2 using 40mm graded stone aggregate as in foundation filling and mass concrete all as specified and directed. |
| 25 | M&L for hand rails half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for balusters, running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc; wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting, etc; MS flats fixed to posts/vertical members including securing bolts for chain link fencing etc, and similar work conforming to Fe-290 Grade E-165 complete all as specified and directed by Engineer-in-Charge. |
| 26 | Supply only Chain link MS galvanized fencing, any size or type |
| 27 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards , rails, straining bolts, etc., including provision of binding wire all as specified and directed. |
| 28 | S&F mild steel round bars 10mm dia and over for securing chain Ink fencing cut to length bent to shape required including bolting etc complete confirming to FE 290 Gde E-165 all as specified and directed |
| 29 | S&F mild steel bolts of dia n exc 12mm purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30 cm long etc complete all as specified and directed. |
| 30 | Dismantling of mild steel Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings, including removing of rusted unserviceable wire from work site and keep serviceable wire for reused in safe custody complete all as specified and directed by Engr-in-charge. |
| 31 | S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins etc, all as specified and as directed. |
| 32 | S&F concertina coil fencing with punched tape barbed Razor concertina coil 600mm dia 10 metre operable length (total 90m) having 50 Nos rounds per 6 metre length, with existing angle iron 'Y' shaped placed 2.4m or 3.0m apart and with 9 horizontal R.B.T reinforced barbed wire, stud tied with GI stapels and GI clips to retain horizontal including necessary bolts or GI barbed wire tied to angle iron all complete in repair, as per direction of Engr-in-Charge with reinforced barbed tape (R.B.T)/ spring core (2.5mm thick) wire of high tensile strength of 165 kg/sq mm with tape (0.52mm thick ) and weight 43.478 gm/metre (cost of MS angle CC blocks shall be paid separately.) |
| 33 | Taking down rolling shutters of area not exceeding 8 Sqm each, replacing worn out/unserviceable parts with new ones, overhauling, applying grease, refixing in position and making them functional complete all as specified and directed. |
| 34 | Taking down rolling shutters of area exceeding 8 Sqm but not exceeding 12 Sqm each, replacing worn out/unserviceable parts with new ones, overhauling, applying grease, refixing in position and making them functional complete all as specified and directed. |
| 35 | M&L for overhauling of rolling shutters of area not exceeding 8 Sqm each (without taking down from position but by opening the hood cover), applying grease for trouble-free operation, refixing the hood cover in position and making them functional complete all as specified and directed. Note : Replacement of parts will be measured and paid for separately in respective items. |
| 36 | M&L for overhauling of rolling shutters of area exceeding 8 Sqm but not exceeding 12 Sqm each (without taking down from position but by opening the hood cover), applying grease for trouble-free operation, refixing the hood cover in position and making them functional complete all as specified and directed. Note for Item No.34.00 to 37.00 : Replacement of parts will be measured and paid for separately in respective items. |
| 37 | S&F mild steel worn wheels and gear wheels, fitted to suspension shaft of the rolling shutter and connecting rod respectively, complete in repairs all as specified and directed.Note: Suspension shaft and connecting rod will be measured and paid for separately. |
| 38 | S&F bevel gear box with crank handle, fitted to connecting rod, complete in repairs all as specified and directed.Note: Connecting rod will be measured and paid for separately. |
| 39 | S&F 25 mm dia mild steel connecting rod, fitted to gear wheel and bevel gear, complete in repairs all as specified and directed. |
| 40 | S&F fabricated lock plate of riveted construction, made of mild steel sheet 3.15 mm thick and 100 mm wide, reinforced with mild steel angle of size 40 mm × 40 mm × 6 mm at top and bottom, interlocked with the bottom-most lath section of curtain, complete in repairs all as specified and directed. |
| 41 | S&F lath section, made from cold-rolled steel strips 1.25 mm thick, with interlocking curls at both edges and a deep corrugation at the centre with a bridge depth not less than 12 mm and each lath section shall be a continuous single piece without any welding joint, complete in repairs all as specified and directed. |
| 42 | S&F lath section, made from cold-rolled steel strips 1.00 mm thick, with interlocking curls at both edges and a deep corrugation at the centre with a bridge depth not less than 12 mm and each lath section shall be a continuous single piece without any welding joint, complete in repairs all as specified and directed. |
| 43 | S&F mild steel clips, riveted at either ends and fitted on ends of lath section, complete in repairs all as specified and directed. |
| 44 | S&F mild steel flat iron 40 mm × 6 mm, as stiffeners in hood cover and stopper to arrest lock plate, including necessary welding etc., complete in repairs all as specified and directed. |
| 45 | S&F mild steel guide channel, of size 65 mm depth, 25 mm width and 3.15 mm thick, including fixing of cleats or supports (not exceeding 750 mm c/c) for attachment to wall or column by means of bolts or screws, complete in repairs all as specified and directed. |
| 46 | S&F mild steel guide channel, of size 75 mm depth, 25 mm width and 3.15 mm thick, including fixing of cleats or supports (not exceeding 750 mm c/c) for attachment to wall or column by means of bolts or screws, complete in repairs all as specified and directed. |
| 47 | S&F mild steel bracket plate, 3.15 mm thick and area not exceeding 0.15 sqm in any shape, fixed to wall with holdfast of mild steel angle 40 mm × 40 mm × 6 mm of length minimum 200 mm from edge of bracket plate, embedded in PCC 1:2:4 type B1 bed block of size 250 mm × 200 mm × 200 mm, and fitted with guide channel by means of 20 mm square bar of suitable length, complete in repairs all as specified and directed. |
| 48 | S&F mild steel bracket plate, 6 mm thick and area exceeding 0.15 sqm but not exceeding 0.25 sqm in any shape, fixed to wall with holdfast of mild steel angle 40 mm × 40 mm × 6 mm, minimum 200 mm from edge of bracket plate, embedded in PCC 1:2:4 type B1 bed block of size 250 mm × 200 mm × 200 mm, and fitted with guide channel by means of 20 mm square bar of suitable length, complete in repairs all as specified and directed. |
| 49 | S&F suspension shaft, made out of mild steel pipe conforming to IS 1161:1968, medium class, 40 mm dia, complete in repairs all as specified and directed. |
| 50 | S&F suspension shaft, made out of mild steel pipe conforming to IS 1161:1968, medium class, 50 mm dia, complete in repairs all as specified and directed. |
| 51 | S&F mild steel cranked handle, suitable for gear-operated type rolling shutter, complete in repairs all as specified and directed. |
| 52 | S&F '00' gauge helical wire or flat spiral spring, fixed to suspension shaft, complete in repairs all as specified and directed. |
| 53 | S&F '0' gauge helical wire or flat spiral spring, fixed to suspension shaft, complete in repairs all as specified and directed. |
| 54 | S&F '2' gauge helical wire or flat spiral spring, fixed to suspension shaft, complete in repairs all as specified and directed. |
| 55 | S&F '3' gauge helical wire or flat spiral spring, fixed to suspension shaft, complete in repairs all as specified and directed. |
| 56 | S&F suspension shaft cage, formed out of 35 mm × 6 mm flat iron, complete in repairs all as specified and directed. |
| 57 | S&F cast iron ball bearing for rolling shutter, complete in repairs all as specified and directed. |
| 58 | S&F mild steel sheet 1.00 mm thick, as in hood cover of any shape, with flat iron stiffeners at both edges and fixed to bracket plate, complete in repairs all as specified and directed. |
| 59 | S&F mild steel safety lever locks with 4 levers, for rolling shutters, complete in repairs all as specified and directed. |
| 60 | S&F collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete in repair all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysNov 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender