Tender For Providing Of Shed Near Bldg No. T-45 At Palchan Under Age (I) R&D Manali.
Tender Value
3.88 Lakhs
Estimated cost
Bid Submission
04 Nov 2026
8 days left
EMD
7760
Bank guarantee accepted
Document Fee
300
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kullu → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of Shed Near Bldg No. T-45 At Palchan Under Age (I) R&D Manali.
BOQ
| Sl. No. | Item Description |
| 1 | Excavating holes/Post Holes in ordinary rocks more than 0.10 cum & up to 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto1.5 m, complete all as specified and directed by engineer in charge. |
| 2 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains in ordinary rocks (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m, complete all as specified and directed by engineer in charge. |
| 3 | M&L for plain cement concrete 1:3:6 (1 Cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources), complete all as specified and directed by engineer in charge. |
| 4 | M&L for random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed by engineer in charge. |
| 5 | M&L for 15 mm cement plaster on the both side and top surface of brick/stone wall in mix : 1:4 (1 cement: 4 fine sand), complete all as specified and directed by engineer in charge. |
| 6 | M&L for brick work with common burnt clay FPS. (non-modular) bricks of class designation 7.5 in superstructure above plinth level uo to floor V level in all shapes and sizes in : cement mortar 1:6 (1 cement : 6 coarse sand) complete all as specified. |
| 7 | M&L for new plastered or unplastered surfaces finishing walls with Acrylic Smooth exterior paint of required shade two or more coat applied @ 1.67 ltr/10 sqm and incl necessary scaffolding, ladders, complete all as specified and directed by engineer in charge. |
| 8 | M&L for structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, complete all as specified and directed by engineer in charge. |
| 9 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required, complete all as specified and directed by engineer in charge. |
| 10 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm), complete all as specified and directed by engineer in charge. |
| 11 | M&L for Painting new steel surfaces applying with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade two or more coats on new work over an under coat of suitable shade with ordinary paint complete all as specified. |
| 12 | Providing and laying Polished Granite stone for Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc., complete all as specified and directed by engineer in charge. |
| 13 | M&L for PCC 1:4:8 in floor subbase (1 cement : 4 Coarse sand (Zone III) derived from natural source ; 8 graded stone aggregate 40mm nominal size derived from natural source), complete all as specified and directed by engineer in charge. |
| 14 | M&L for Kota stone slab flooring over 20 mm (average) to 25 mm thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand), complete all as specified and directed by engineer in charge. |
| 15 | M&L for Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing, complete all as specified and directed by engineer in charge. |
| 16 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron), complete all as specified and directed by engineer in charge. |
| 17 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not lessthan 10kg/sqm), complete all as specified and directed by engineer in charge. |
| 18 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed by engineer in charge. Note: Only weight of grill to be measured for payment. |
| 19 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer and Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), complete all as specified and directed by engineer in charge. |
| 20 | Providing and fixing ISI marked 30mm thick flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters incl ISI marked stainless steel butt hinges with necessary screws, complete all as specified and directed by engineer in charge. |
| 21 | Providing and fixing aluminium tower bolts, size 250x10 mm ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc., complete all as specified and directed by engineer in charge. |
| 22 | Providing and fixing aluminium sliding door bolts, size 300x16 mm ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc., complete all as specified and directed by engineer in charge. |
| 23 | Providing and fixing aluminium handles,size 125mm ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc., complete all as specified and directed by engineer in charge. |
| 24 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc., complete all as specified and directed by engineer in charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender