Tender For Provn Of Entrance Arch For Barrier Gate At K Tee Contonment.
Tender Value
4.16 Lakhs
Estimated cost
Bid Submission
04 Nov 2026
20 days left
EMD
8320
Bank guarantee accepted
Document Fee
300
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nagpur → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Entrance Arch For Barrier Gate At K Tee Contonment.
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches not exceeding 1.5m in depth and 1.5m in width and getting out in hard/dense soil complete all as specified and as directed. |
| 2 | M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundation, mass concrete and fillings complete all as specified and as directed. |
| 3 | M&L for Formwork to side of concrete in foundations, footing base, base of columns, side and soffits of plinth beam and similar work complete all as specified and as directed. |
| 4 | M&L for providing RCC Nominal Mix of cement concrete Type B0 1:2:4 using 12.5 mm aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. |
| 5 | M&L for Formwork to side of columns and similar work complete all as specified and as directed. |
| 6 | M&L for providing RCC Nominal Mix of cement concrete Type B0 1:2:4 using 12.5 mm aggregate in Columns, pillars, piers, posts, and struts complete all as specified and as directed. |
| 7 | M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:4 mixed with WPC finished even and smooth without using extra cement complete all as specified and as directed.(Note: WPC will be measured & paid separately). |
| 8 | Supply only Liquid water proofing compound of approved quality complete all as specified and as directed. |
| 9 | S&F mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including crancing bending and binding with mild steel(annealed) wire not less than 0.90mm dia complete all as specified and as directed. |
| 10 | S&F mild steel TMT bars 8 to 10mm dia as in stirrups, spacers and binders complete all as specified and as directed. |
| 11 | S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and as directed. |
| 12 | S&F for 16 to 20 mm Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 5cm but n exc 10cm long complete all as specified and as directed. |
| 13 | M&L Mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W Gde E-250 quality B complete all as specified and as directed. |
| 14 | S&F of Mild steel, plain, black sheet of 2 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed |
| 15 | Preparation of newly steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 16 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and as directed. |
| 17 | Removing excavated material(soil) n exc 50m and deposited where directed at a level n exc. 1.5m above the strating point complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysNov 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender