Tender For Repair & Replacement To Galvalume Roof Sheets In Lieu Of Asbestos Sheet To Certain Buildings In Aor Of Ge (West) Agra
Tender Value
77.67 Lakhs
Estimated cost
Bid Submission
11 Nov 2026
16 days left
EMD
1.41 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Agra → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair & Replacement To Galvalume Roof Sheets In Lieu Of Asbestos Sheet To Certain Buildings In Aor Of Ge (West) Agra
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of asbestos cement (corrugated, semi corrugated etc) sheets in roof covering including ridges etc complete all as specified and as directed |
| 2 | Dismantling timber scantlings, fillets, rails, posts, rafters, purlins, etc., under 40 sq cm in section, in any position, complete all as specified and directed. |
| 3 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets any thickness, including cover fillets complete all as specified and as directed |
| 4 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of approved colour having tensile strength of 550 Mpa as in roof covering or cladding to wall, fixed with self tapping screws, complete as specified and as directed.Note :- (i) Colour of sheet shall be as approved by Engineer-in-Charge(ii)The sheet shall be provided with a protective guard film of minimum 25 microns thickness to prevent scratches during transportation and shall be supplied in a single length of up to 12 m, or as directed by the Engineer-in-Charge. (iii) The sheet shall be fixed using self-drilling/self-tapping screws of size 5.5 × 55 mm with EPDM seals complete at the required pitch and spacing, in horizontal, vertical or curved surfaces, as applicable, complete all as specified and directed. |
| 5 | S & F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of approved colour having tensile strength of 550 Mpa as in roof covering or cladding to wall, ridges, etc, fixed with self tapping screws, complete as specified and as directed.Note :- (i) Colour of sheet shall be as approved by Engineer-in-Charge(ii)The sheet shall be provided with a protective guard film of minimum 25 microns thickness to prevent scratches during transportation and shall be supplied in a single length of up to 12 m, or as directed by the Engineer-in-Charge. (iii) The sheet shall be fixed using self-drilling/self-tapping screws of size 5.5 × 55 mm with EPDM seals complete at the required pitch and spacing, in horizontal, vertical or curved surfaces, as applicable, complete all as specified and directed. |
| 6 | Demolition of brick work or stone /boulder masonary built in cement mortar or cement lime mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and directed. |
| 7 | M&L for brick work with old size sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 8 | All as per item No. 7 above, but except bricks, including cleaning of old size bricks and removing mortar therefrom complete all as specified and directed.Note :- Serviceable bricks retrieved from item No. 6 shall be reused. |
| 9 | M&L for cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in copings, kneelers, apex stones, bed plate and similar works including necessary form work (straight or curved) complete all as specified and directed |
| 10 | Taking down cement or cement lime plaster on brick or stone walls or concrete surfaces etc (any thickness) including raking out joints, hacking for key, scrubbing down with water etc, including removal of rubbish off the premises, complete all as specified and as directed |
| 11 | M&L for 10 to 12 mm thick SmartCare ready-mix repair plaster containing high-quality polymer additives, well-graded sand and fillers, suitable for plastering of interior wall surfaces, applied in accordance with the manufacturer’s instructions, including surface preparation, mixing, application and finishing complete all as specified and as directed |
| 12 | M&L for 15 mm thick SmartCare ready-mix repair plaster, specially formulated as a ready-to-use cement-based plaster with high-quality polymer additives, well-graded sand and fillers, suitable for plastering of exterior wall surfaces, applied in accordance with the manufacturer’s instructions, including surface preparation, mixing, application and finishing, complete all as specified and as directed |
| 13 | M&L for preparation of newly plastered wall surfaces, and applying three coats of white wash, complete all as specified and directed |
| 14 | M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over and including a coat of alkali resistant primer complete all as specified and directed |
| 15 | M&L for steel work in tubular trusses, including special shaped washers etc and all necessary accessories, complete using ERW or induction butt welded steel tubes conforming to IS 1161:1979, Grade St-240, complete all as specified and directed. |
| 16 | S&F powder coated aluminium alloy interlocking snap grid 600mm x 600mm consists of Min Tee runners of size 38mm x 25mm x 1.5mm and cross Tee of size 25mm x 25mm x 1.5mm, spaced between the main Tee at 600mm center to center to form a grid of 600mm x 600mm and wall angle 25mm x 25mm x 2mm fixed to wall perimeters at 450mm centres and shall confirm to IS 733, IS 1285 with and including hangers of 6mm dia, GI (upto 1200mm length and 1200mm centres) adjusting level fixed to roof steel members by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long etc complete all as specified and directed. |
| 17 | M&L for 4 mm thick non-asbestos fibre cement building boards, fixed or laid/inserted to timber/GI/aluminium framework with suitable screws, for ceilings, whether flat or sloping, including cutting, fitting and fixing to the required size and shape, complete all as specified and directed. |
| 18 | M&L for rolled mild steel sections for roof trusses (framed), trussed purlins, crane gantries, rails and fastenings, and heavy bracket framing, comprising beam, tee, angle, channel or flat sections, including distance pieces, cleats and other necessary accessories, conforming to Fe 410-W (Grade E-250), Quality A, complete all as specified and directed. |
| 19 | M&L for rolled mild steel plates, plain or chequered, including channels, square-cut or notched, with ordinary or countersunk holes, without any attachments, conforming to Fe 410-W (Grade E-250), Quality A, complete all as specified and directed. |
| 20 | M&L for preparation of new or previously untreated steel or iron surfaces of any description over 10 cm width or girth and applying two coats of first quality synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed. |
| 21 | M&L for preparation of old painted steel or iron surfaces of any description over 10 cm width or girth and applying one coat of first quality synthetic enamel paint, complete all as specified and directed. |
| 22 | M&L for preparation of old painted wood and wood based surfaces of any description over 10 cm width or girth and applying one coat of first quality synthetic enamel paint, complete all as specified and directed. |
| 23 | Taking down copper/aluminium point wiring of any description and any position (light, fan, socket or power point) complete, including fixture and fittings such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified. Please Enable Macros to View BoQ information |
| 24 | Taking down copper/aluminium point wiring of any description and any position (light, fan, socket or power point) complete, including fixture and fittings such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender