Tender For Special Repair Of Bldg No. 15 (Or Bathroom / Toilet) Of Hq Ddgsi (Nz) Under Age B/R-I And Replacement Of Colour Coated Galvanised Sheet Roof At Bldg No. Np-01 (Security Jco Room) At Depot Area At Ncvd Under Age B/R-Ii Under Ge (North) Udh
Tender Value
18.66 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
10 days left
EMD
37320
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udhampur → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair Of Bldg No. 15 (Or Bathroom / Toilet) Of Hq Ddgsi (Nz) Under Age B/R-I And Replacement Of Colour Coated Galvanised Sheet Roof At Bldg No. Np-01 (Security Jco Room) At Depot Area At Ncvd Under Age B/R-Ii Under Ge (North) Udh Ur.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un-reinforced) as in ground floor and paving area of any type and any thickness, complete all as specified and directed. |
| 2 | Taking down cement or cement lime plaster on brick or stone walls etc. of any description including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 3 | Dismantling of wall and ceiling board (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets of any thickness including cover fillets, complete all as specified and directed. |
| 4 | Taking down chowkats or frames (without taking off shutters from frame), area not exc 1.50 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed. |
| 5 | Taking down chowkats or frames (without taking off shutters from frame), area exc 1.50 Sqm but not exc 4.00 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed. |
| 6 | Dismantling of plain or corrugated roof sheeting of any type and any thickness including roof covering, ridges etc, complete all as specified and directed. |
| 7 | Dismantling of structural steel work of any description and in any position, complete all as specified and directed. |
| 8 | Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, aches, pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles, complete all as specified and directed. |
| 9 | Dismantling of floors, hearth and wall tiling of any description or thickness as in floor, dados, apron etc, laid, bedded and pointed in any mortar, complete all as specified and directed. |
| 10 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads, complete all as specified and directed. |
| 11 | Taking up or down steel tubing and connection including cleaning for re-fixing or removal to store of dia of pipe 15mm, laid on floor or walls, complete all as specified and directed. |
| 12 | Taking up or down steel tubing and connection including cleaning for re-fixing or removal to store of dia of pipe 20mm, laid on floor or walls, complete all as specified and directed. |
| 13 | Dismantling of water tank of capacity 1000 ltrs and removing to store, complete all as specified and directed. |
| 14 | M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6 mtr mean radius, built in CM 1:4, complete all as specified and directed. |
| 15 | M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6 mtr mean radius, built in CM 1:6, complete all as specified and directed. |
| 16 | M&L for half brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6 mtr mean radius, built in cement mortar 1:4, complete all as specified and directed. |
| 17 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6, finished even and smooth w/o using extra cement, complete all as specified and directed. |
| 18 | M&L for rendering 15mm thick on any surfaces such as stone masonary, brick work or surface other than brick work/ stone in CM 1:4, finished even and smooth w/o using extra cement, complete all as specified and directed. |
| 19 | M&L for rolled mild steel work of angle, tee, flats and plates as in roof trusses, purlines, rails etc. and the like, fixed with angle cleats and connecting plates including welding, confirming toFe-410-W (Gde-E- 250) quality-A, complete all as specified and directed. |
| 20 | S&F 0.50mm thick prepainted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering, cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 21 | S&F 0.50mm thick prepainted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering, cladding to wall, ridges etc, fixed with self tapping screws, complete all as specified and directed. |
| 22 | S&F 0.80mm thick plain galvanised mild steel sheeting as in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, complete all as specified and directed. |
| 23 | M&L for hardcore of broken stone or boulders of gauge not exc 63mm, deposited, spread and leveled in layers not exc 15cm thick including watering and ramming to a true surface, complete all as specified and directed. |
| 24 | M&L for 25mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in flooring, sub base and finished the surface even and smooth with using extra cement, complete all as specified and directed. |
| 25 | M&L for non skid ceramic coloured tiles of 7 to 8mm thick (square / rectangular), area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floor, skirtings etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/ fixed over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 26 | M&L for glazed ceramic coloured tiles as on vertical surfaces, size of each tile 350mm x 250mm x 7mm or 450mm x 350mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick rendering in CM 1:4, complete all as specified and directed. |
| 27 | M&L for 10mm thick coloured vitrified light shade ceramic tiles (square / rectangular), polished, area of each tiles not exceeding 0.36 Sqm as in floors, skirtings etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/ fixed over and including 15mm thick screed bed/ plaster in CM 1:4, complete all as specified and directed. |
| 28 | M&L for 18-20mm thick machine cut kota stone slab flooring as in floors, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid/ fixed over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 29 | M&L for 18-20mm thick machine cut kota stone slab as in riser of steps, skirting, dados and pillar, set, jointed and pigment to match the shade of the slab including rubbing and polishing, fixed over and including 10mm thick rendering 1:4, complete all as specified and directed. |
| 30 | M&L for 50mm thick PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in plinth protection, finished even and smooth without using extra cement including making joints 10mm wide and 30mm deep at spacing not more than 2.5 mtr and at corners at mandatory and filled with sealing compound Grade A, complete all as specified and directed. |
| 31 | S&F false ceiling with fibre cement designer tile ivory painted (high pressure steam cured) of 4mm thickness (as per IS:14862) of size 595mm x 595mm and any one of the design (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main 'T' runner with suitably spaced joints to get required length and 15x32mm made of 0.30mm sheet, and cross 'T' at 600mm c/c to form a grid including required cutting/ making, opening for services like diffusers, grills, light fittings, fixures, smoke detectors etc. Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin etc. with gavanised butterfly level clips, spaced at 1200mm c/c along main T, bottom exposed width of 15mm of all 'T' sections shall be centra black pre-painted with polyester paint and having a load bearing capacity of 12 Kg/sqm and refixed all exesting electric wiring and fixture all complete at any heights as per direction of Engineer-in-Charge. |
| 32 | M&L for mild steel framed work such as grills, guard bars, railing, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work, conforming to Fe-290 Gde-E-165, complete all as specified and directed. |
| 33 | S&F sheet glass 4mm thick ordinary quality and glazing with beading / oil putty in square not exc 0.50 Sqm each pane, complete all as specified and directed. |
| 34 | S&F steel ventilators, fixed type with glazing bars, complete all as specified and directed by Engr-in-Charge. |
| 35 | S&F looking mirror of 5.5mm thick, bevelled edge of selected quality glass with aluminium frame, made of channel section alround, mounted on 6mm thick commercial ply or AC building board, fitted to wooden plug with CP screws, complete all as specified and directed. |
| 36 | M&L for preparation of new plastered surfaces by using necessary compound of Altek/ Birla white putty 1.0 to 1.2mm thick to obtain smooth/ even finish using sand paper and applying two coats of distemper oil emulsion over a coat of alkali resistant cement based priming paint, complete all as specified and directed. |
| 37 | M&L for preparation of old plastered or un-plastered surface by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorence salts and trading oil and greasy spots and filling nails marks with compound of wall putty and sand papering and applying one coat of distemper oil emulsion, white or tinted, complete all as specified and directed. |
| 38 | M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of alkali resistant cement base primer, complete all as specified and directed. |
| 39 | M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint, white or tinted, over a coat of chalk whitening primer and including over 1-2mm thick wall cair putty, complete all as specified and directed. |
| 40 | M&L for complete removal of old surface of walls and smoothening the surface and applying two coats of distemper oil emulsion over a coat of primer and including applying 1-2mm thick wall cair putty, complete all as specified and directed. |
| 41 | M&L for preparation of new or previously untreated steel and iron surface of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed. |
| 42 | S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed with SS screws, complete all as specified and directed. |
| 43 | S&F 300mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed. |
| 44 | S&F 150mm size mild aluminium handles, cast type anodised, complete all as specified and directed. |
| 45 | S&F 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed. |
| 46 | S&F vitreous china squatting pan, orissa pattern of size 580mm x 440mm white with integral foot rests and fixed with cement concrete bedding, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 47 | S&F vitreous china squatting pan, orissa pattern of size 580mm x 440mm white with integral foot rests and fixed with cement concrete bedding, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender