Tender For Provn Of Toilet Facilities For Staff And Visitors Of Camero Urc At Subroto Park, Provision Of Split Acs (Qty-09) For L-2 Switch Room With Associated Works At Afcao At Camero Complex, Provision Of Corridor Gallery From Entrance Gate To Buil
Tender Value
46.75 Lakhs
Estimated cost
Bid Submission
02 Nov 2026
15 days left
EMD
93500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Toilet Facilities For Staff And Visitors Of Camero Urc At Subroto Park, Provision Of Split Acs (Qty-09) For L-2 Switch Room With Associated Works At Afcao At Camero Complex, Provision Of Corridor Gallery From Entrance Gate To Building No P-83 (B) At Camero Complex And Provn Of Aluminium Partition & Door At Afro Office Room No 301 And 105 At Camero Complex
BOQ
| Sl. No. | Item Description |
| 1 | Surface dressing n exc 15 cm deep in soft/loose soil complete all as specified and directed. |
| 2 | Excavation in trenches n.exceeding 1.50m wide and n.exc 1.50m depth for foundation etc or for shafts, walls, cess-pits, manholes, pier holes etc n.exc. 10 sqm on plan and n.exc. 1.5m in depth, getting out in Hard/Dence soil complete all as specified and directed. |
| 3 | M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering as required complete all as specified and directed. |
| 4 | M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and/rammed to a true surface all complete as directed. |
| 5 | M & L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed. |
| 6 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 7 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 8 | M & L Reinforced cement concrete Design mix (M-25) as in Foundations, including rafts, footings, and mass concrete and the like complete all as specified and directed. |
| 9 | M & L Reinforced cement concrete Design mix (M-25) as in roof beam, plinth beam and lintel beams complete all as specified and directed. |
| 10 | M & L reinforced cement concrete Design mix (M-25) as in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 11 | M & L Reinforced cement concrete Design mix (M-25) as in Slabs supported on walls, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 12 | M & L Reinforced cement concrete Design mix (M-25) as in chajjas complete all as specified and directed. |
| 13 | M & L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, footing, roof beam, plinth beam, slab,chajjas and similar work hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 14 | Ditto all as per item no 12 but 5 mm dia and over up to and incl 8mm dia as in stirrups |
| 15 | M& L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and directed. |
| 16 | M& L for Formwork to sides of columns, pillars, posts, struts and stanchions etc complete all as specified and directed. |
| 17 | M& L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 18 | M& L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 19 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. |
| 20 | M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 M mean radius built in CM 1:6 complete all as specified and directed. |
| 21 | M&L Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 22 | Material & labour for 15 mm thick rendering in CM 1:4 on brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 23 | Material & labour for 5 mm thick rendering in CM 1:3 on brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 24 | M&L for preparation on new or previously untreated wall and applying Two or more coats of 100% Premium acrylic emulsion paint having and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) over and including priming coat exterior primer applied @ 0.90 litre/ 10 sqm new surfaces up to four stories bldgs complete all as specified and directed by Engineer-in-Charge. |
| 25 | M&L for preparation of new plastered surfaces of walls and applying three coats of white wash on ceiling surface complete all as specified and directed. |
| 26 | S&F aluminium frame powder coated any colour (minimum thickness of powder coating 50 micron) for doors, windows, partician, ventilators with one or more rebates including joining cleat for fixing etc.complete all as specified. |
| 27 | S&F aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) incl powder coating of any colour (Thickness or powder coating not less than 50 micron).complete all as specified. |
| 28 | M&L for figured glasspine head type 3.0 mm thick ordinary quality and glazing with oil putty, in squares n. exc 0.5 Sq.M in each pan complete all as specified and directed. |
| 29 | S&F 10mm plain toughned glass for urinal pot partition with complete fittings of SS nut bolts and clamps all as specified and as per manufacturer's instructions. |
| 30 | M&L for Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screed in CM(1:6) complete all as specified and as directed. |
| 31 | M&L for glazed ceramic coloured tiles 450mm x 300 mm size 6 to 7mm thick in dados or skirting over & including rendering 10mm thick in CM (1:4), jointed in neat grey cement slurry and pointed in white or colour cement to match the tiles as directed and specified. |
| 32 | S&F Vitreous China wash basin white ovel shape counter top of size 430x345mm including PVC waste pipe of 32mm dia of suitable length, 32mm dia brass waste fitting and all fitting complete all as specified and as directed . |
| 33 | S&F in repair vitreous china squatting pan “orrisa” pattern of size 580mmx440mm “white” with integral foot rest (excluding flushing cistern and flush pipe) incl provision of cement concrete bedding, ‘P’ trap 100mm dia connection to trap , anti-syphonage complete all as specified and directed. |
| 34 | S&F in repair for vitreous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, excluding fixing bolts, flushing cistern and flush pipe) complete all as specified. |
| 35 | S&F in repairs10 ltr capacity PVC flushing cistern coloured with accessories Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete and specified and directed. |
| 36 | S & F 32 mm bore low density polythene pipe (LDPE) of pressure rating 6 kgf / Sqcm for WHB and sink complete all as specified and directed. |
| 37 | S & F in repairs for 125mm dia Steelness steel grating doom with waste hole for waste pipe ( minimum weight 40 gram) complete all as specified and directed. |
| 38 | S & F Bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified and directed. |
| 39 | S&F of fancy type chromium plated two way bib cock of 15mm bore ,screwed for iron pipe or brass ferrule etc complete all as specified and as directed. |
| 40 | S&F 15 mm table top basin faucet tap chromium plated screwed down high pressure, fancy type with handle complete all as specified and directed. |
| 41 | S & F stop/angle cock cast copper alloy high pressure, angle valve type, chromium plated suitable for 15mm bore steel pipe complete all as specified and directed. |
| 42 | S&F of health faucet with S.S. flexible pipe of 1.00 to 1.50 metre length including holder complete all as specified and as directed. |
| 43 | S & F PVC connections of 450mm long of suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed. |
| 44 | S & F 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed. |
| 45 | S & F 20mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed. |
| 46 | S&F 15mm bore Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 47 | S & F rotational moulded polythylene 1000 Ltr capacity water storage tank (double layer)(cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 20mm bore complete all as specified and directed. |
| 48 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm vide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 49 | S & F CP Toilet paper holder, complete all as specified and directed. |
| 50 | S & F corner shelf of 300 mm size with ABS brackets complete all as directed and specified. |
| 51 | M&L 5mm thick frame less mirror with chromium plated brass clam screws and cup washers or fixing arrangement to wall complete all as specified and directed. |
| 52 | S&F liquid soap dispenser with s/s metallic bottle complete, all as specified and directed. |
| 53 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). → Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 54 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face ) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved designpasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. |
| 55 | S & F stainless steel butt hinges 100 mm long complete all as specified and directed. |
| 56 | S&F 150 mm long stainless steel tower bolts of extruded section complete all as specified and directed. |
| 57 | S&F 150 mm size stainless stee handle complete all as specified and directed. |
| 58 | S&F for 250mm long stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete and specified and as directed. |
| 59 | M&L for 10 mm thick cement mortar 1:4 on fair faces of brick or concrete surfaces with and including integrlal water proofing compound as per manufacturers instructions complete all as directed and specified. |
| 60 | M&L for preparation of plastered/concrete surfaces of roof and applying the under mentioned course of roof treatement complete all as specified and directed by Engineer-in-Charge.:-(a) Surface shall be throughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface.(b) Laying of 3mm thick prefabricated APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 170 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc. Note:- This treatement shall be done by the approved authorized applicators and guarantee of treatement shall be minimum 10 years complete all as specified and directed by Engr In Charge. |
| 61 | M&L for applying two coats of bitumen based aluminium painting @ 0.15 Kg / sqm each coat on water proofing treatment with preparation of surface complete all as specified and directed. |
| 62 | S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed laid in trenched or floors complete all as specified and directed. |
| 63 | S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints fixed laid in trenched or floors complete all as specified and directed. |
| 64 | S&F PVC (SWR) bends any radius 110mm dia complete all as specified and directed. |
| 65 | S&F PVC (SWR) bends any radius 75mm dia complete all as specified and directed. |
| 66 | S&F PVC junction single (single T) 110mm dia equal or unequal with access door complete all as specified and directed. |
| 67 | S&F PVC junction single (single T) 75mm dia equal or unequal with access door complete all as specified and directed. |
| 68 | S&F 100mm stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 69 | S&F 75mm stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof v |
| 70 | M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement complete all as specified and directed. |
| 71 | M&L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement complete all as specified and directed. |
| 72 | S&F 150 mm bore (inner dia) double wall corrugated HDPE pipes (SN8) in any length including all fittings and jointing with elastomeric rubber rings and couplers / other jointing materials as per manufacturers instructins, laid over and including 150 mm thick sand coushning in trenches or in floors all as specified and directed. |
| 73 | S&F 200 mm bore (inner dia) double wall corrugated HDPE pipes (SN8) in any length including all fittings and jointing with elastomeric rubber rings and couplers / other jointing materials as per manufacturers instructins, laid over and including 150 mm thick sand coushning in trenches or in floors all as specified and directed. |
| 74 | M & L for concrete bed PCC 1:4:8 Type D2 (Using 40mm graded stone aggregate) to drain pipes 150 mm dia including packing under and haunching against the sides of pipes after they are laid and tested all as specified and as directed. |
| 75 | M & L for concrete bed PCC 1:4:8 Type D2 (Using 40mm graded stone aggregate) to drain pipes 200 mm dia including packing under and haunching against the sides of pipes after they are laid and tested all as specified and as directed. |
| 76 | M & L for Precast cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, bed plates, pintle blocks, anchorage blocks, cover slabs (for manholes and drains etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 including necessary form work , complete all as specified and directed. |
| 77 | M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in coping to drainage complete all as specified and directed. |
| 78 | S & F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders;Chajj, framed balusters; walk ways; railings; cooler stand,stair, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 79 | S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as specification complete all as specified and directed. |
| 80 | S & F steel work in tubular trusses , including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161 1979 grade St-240 complete all as specified and directed. |
| 81 | M&L Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide/ zinc chromate complete all as specified and directed. |
| 82 | M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20mm graded stone aggregate) as in plinth protection Finishing surfaces of concrete topping even and fair (without using extra cement) including making joint at every 3 mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed. |
| 83 | M & L Granite (of any type) 18-20mm work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm screed bed in CM 1:6 all spd and directed . |
| 84 | Rounding to edges of stone slabs such as granite and kota stone ,one edge such as steps cooking platform and other similar situations complete all as specified and as directed. |
| 85 | Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in hard/dence soil complete all as specified and directed. |
| 86 | M&L for Chequered cement concrete tiles (rubber moulded with gloshy finishing) with grey cemet and pigments 30cm x30cm x 25 mm thick, set, jointed and pointed in neat cement slurry in floors with 15mm thick bedding layer of cement sand mortar (1:6). complete all as specified and directed. |
| 87 | Dismantling of precast concrete paver block and removing of debries out side of defence land complete all as specified and directed. complete all as speciified. |
| 88 | M& L for 80 mm thick, M-35 grade machine pressed precast interlocking concrete coloured (Red/yellow) paver block in any shape and size with grey cement and pigment as approved confirming to IS 15658-2006 complete all as specified and as directed. |
| 89 | M&L for Sand filling under floors in foundation including watering and consolidation complete all as specified and directed. |
| 90 | S & F aluminium extruded section door closer hydraulically operated designation No-03, universal type, suitable for door shutters of 851 to 1000mm width and of weight of 61 to 80 Kg complete all as specified and directed. |
| 91 | S&F 12mm thick particle board prelaminated on both sides as in panel of door shutters partition wall, work stations including beading etc.omplete all as specified and directed. |
| 92 | Supply and fix sheet glass 5.5 mm thick of selected quality (tinted glass/plane) exc. 0.5 sqm each fixed to aluminium frame work with necessary rubber beading complete all as specified and directed. |
| 93 | Supply and fix sheet glass 5.5 mm thick of selected quality (tinted glass/plane) n. exc. 0.5 sqm each fixed to aluminium frame work with necessary rubber beading complete all as specified and directed. |
| 94 | S&F for powder coated aluminium sliding doors shutters,( thickness of powder coating not less than 50 micron) alumonium section weighing 0.55 kg/m incl necessary joining cleats, glazing clips, glass,partical board, roller, rubber neoprene packing , handels 2 Nos in each door , anodised aluminium snap beading screws etc. complete all aspecified and directed. |
| 95 | S&F for powder coated aluminium doors shutters,( thickness of powder coating not less than 50 micron) alumonium section weighing 0.55 kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing , handels 2 Nos in each door , hinges, anodised aluminium snap beading screws etc. complete all aspecified and directed. |
| 96 | S&F brass body mortice lock vertical type size 100mm 4 lever, including escutcheon plate and two No keys fixed complete all as specified and directed. |
| 97 | S&F in aluminium deco grills confirming to DG-104 grade all as specified and directed. |
| 98 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and as directed. |
| 99 | Taking down cement or cement lime plaster any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 100 | M&L rendering 10mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement complete all as specified. |
| 101 | M&L for preparation of new plastered surfaces of walls, and applying two coats of distemper oil emulsion over a coat of primer on walls up to four storey height building complete and specified and as directed. |
| 102 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.complete all as specified and directed. |
| 103 | M&L Vitrified Ceramic tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) omplete all as specified and directed. |
| 104 | M &L for PVC profile for wall panelling colour / shade as approved size 250mm wide, 08 mm over all thick with 1 mm wall thickness fixed with screw to mild steel square ( size 20mmx 20mmx 1mm thick) tubler frame work including one coat of red oxide primer, fixed to walls complete all as specified and directed. |
| 105 | Material and labour for false ceilings using GI sanp grid system with rool-formed out of hot drip galvanised steel capings (Powder coated) main runner 38mmx24mm, cross Tee 29mmx24mm and wall angle 24x24mm members suspended with 4mm dia GI wire, carry maximum load up to 8.10 Kg/Sqm with 4mm thick designer ceilimg board, prepainted cement fibre board size 595mmx595mmx4mm thick any texture (Lake, Hill, ocean cascade or Electra ) suspended from from RCC roof/ structural members of soofits angle cleat cut out etc to ther equired line and shape as per manufactureres recommndations at any height complete all as specified and as directed. |
| 106 | S&F factory made 18mm (+0.7mm) thick celuka PVC ply of density 600kg/cbm manufactured by an ISO-900-2008 certified company.One side prelam and other side plain 18mm thick Celuka PVC ply for kitchen cabinet shutter and also manufactures test report and test certificate is mandatory with each and every supply of the material complete as specified and directed. |
| 107 | S&F in repair factory made 18mm(+0.7mm) thik celuka PVC Ply of density 600kg/cbm manufactured by an ISO-900-2008 certified company.Plain 18mm thick Celuka PVC Ply for Shelf/Partitions/Drawer/Back side and also manufacturer's test report and test certificate is mandatory with each and every supply of the materail complete all as specified and directed. |
| 108 | S&F 38mm size Stainless Steel Piano hinges complete all as specified and as directed. |
| 109 | S&F 100 mm size Stainless Steel handle complete all as specified and as directed. |
| 110 | M &L for 50 mm magnetic catches and fixed complete all as specified and directed. |
| 111 | Excavating in post holes ( or similar holes) in hard and dense soil each n exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubbel mixed with earth around, in layer not exceeding 25 cm soft/disgrated complete all as specified and directed. |
| 112 | M&L for cement concrete type C2 1:3:6 (40mm graded stone aggregate) for fixing of post holes complete all as specified and directed. |
| 113 | S&F roof trusses (framed), trussed, purlins,crane gantries, rails and fastnings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specifeid and directed. |
| 114 | MS plates/flats angle etc as in cleat gusset plate incl drilling welding etc complete all as specified and directed. |
| 115 | S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an color having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete al as specified and directed. Please Enable Macros to View BoQ information |
| 116 | S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an color having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete al as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender