Tender For Construction Work For Extension Of Control Room Building, Equipment Foundations And Other Ancillary Works For Capacity Augmentation At Gourhati 33/11 Kv Sub-Station Under Arambagh Division, Wbsedcl In The District Of Hooghly
Tender Value
11.58 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
20 days left
EMD
23166
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hooghly → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Work For Extension Of Control Room Building, Equipment Foundations And Other Ancillary Works For Capacity Augmentation At Gourhati 33/11 Kv Sub-Station Under Arambagh Division, Wbsedcl In The District Of Hooghly
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm. |
| 2 | (b) Depth of excavation exceeding 1,500 mm and up to 3000mm but not requiring shoring. |
| 3 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)(a) With earth obtained from excavation of foundation. |
| 4 | Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 5 | Hire and labour charges for shoring work (including necessary close plank walling, framing, Eucalyptus/Jhou bulla piling, strutting etc) complete as per direction of the Engineer-in-charge for foundation excavation (vertical surface are in contact with supported earth is to be measured.) (This item should be executed on specific direction of the Enginner in charge). |
| 6 | (a) Depth upto 1.5 m. |
| 7 | (b) For additional depth beyond 1.5 m. and upto 3.00 m |
| 8 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 9 | Cement concrete with graded stone ballast (40 mm size excluding shuttering). In ground floor and foundation.(A) Pakur Variety. (a) 6:3:1 proportion |
| 10 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips(20 mm.nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes.a) Pakur Variety i) In ground floor and foundation. |
| 11 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm.nominalsize) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes.a) Pakur Variety.i) In ground floor and foundation. |
| 12 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes.Pakur variety |
| 13 | Artificial stone in floor, dado, staircase etc. with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted) with ordinary cement.Using grey cement.(i) 35 mm. thick (In ground floor only) |
| 14 | Anti termite treatment to the top surface of the consolidated earth within plinth walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. of the surface before sand bed or sub-grade is laid. Holes upto 50 mm. to 75 mm. deep at 150 mm. centre to centre both ways shall be made with 12 mm, diameter mild steel rod on the surface to facilitate saturation of the soil with the chemical emulsion. The work shall be carried out as per specification described in para 6.4 of code IS6313 (part -II) 1981. ( Mode of measurment will be per Sq.m of plan area of plinth treated.) |
| 15 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups,binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bennding to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.Mild steel/ Tor steelJSW/JSPL/SHYAM/SRMB/BMASL/ELECTROSTEEL/SSLi)Ground floor |
| 16 | Brick work with 1st class bricks in cement mortar (1:6)(a) In foundation and plinth |
| 17 | (b) In superstructure, ground floor |
| 18 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 19 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface.](A) With 1:6 cement mortar(i) In ground floor (15 mm thick plaster) |
| 20 | (ii) In ground floor (20 mm. thick plaster) |
| 21 | (B) With 1:4 cement mortar(i) In ground floor (10 mm. thick plaster) |
| 22 | Neat cement punning about 1.5 mm. thick in wall, dado, window, sills, floor, drain etc.Note: Cement 0.152 cu.m. per sq.m. |
| 23 | Hire and labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works .(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.i)Ground floor |
| 24 | (b) 25 mm to 30 mm shuttering without staging in foundation etc. |
| 25 | Hire and Labour Charges for shuttering with hard wood for precast R.C. Slab curved, or stright and striking out the same including fitting, fixing the precast slab in position with necessary carriage and haulage, hosting etc, complete in all respect.(only the area in contact with concrete to be measured) |
| 26 | Labour for Chipping of concrete surface before taking up Plastering work. |
| 27 | Supplying and laying Polythene sheet (150gm /sq.m.) over damp proof course or bellow flooring or roof terracing or in foundation or foundation trenches. |
| 28 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor:(a) One Coat |
| 29 | Protective and decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required.The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.Premium 100% Acrylic Emulsion (Two Coat). |
| 30 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or concrete surface old or new surface to receive distemper / acrylic emulsion paint including scrapping and preparing the surface thoroughly, complete as per manufacturer's specification and as per direction of E.I.C One coat. i) Water based interior grade Acrylic Primer |
| 31 | Applying Acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermidiate course including putty (two coats). Standard Quality. |
| 32 | Rendering the surface of walls and ceiling with white cement basedwall putty of approved make and brand(1.5mm thick) |
| 33 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 34 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 35 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary. |
| 36 | (a) On steel or other metal surface :With super gloss (hi-gloss) - Two coats (with any shade except white) |
| 37 | (b) On timber or plastered surface :With super gloss (hi-gloss) -Two coats (with any shade except white) |
| 38 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.a) In Ground floor including roof |
| 39 | Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.In Ground floor including roof.(a) upto 150 mm. thick |
| 40 | Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars. In ground floor including roof. |
| 41 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal /Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge |
| 42 | Clearing compound premises from shurbs, plants, jungles, etc. by cutting and removing as directed. |
| 43 | Cutting holes and subsequent mending good damages.(a) Diameter upto 150 mm.(i) In brick work |
| 44 | Cutting chase up to 125 x 150 mm and subsequent mending of damages. In brick wall [Cement-3.6Kg/ Mtr] |
| 45 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 46 | Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific directionof the Engineer-in-charge) |
| 47 | Removing loose scales, blisters etc. from old painted surface and thoroughly smoothening the surface to make the same suitable for receiving fresh coat of paint. |
| 48 | Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge. |
| 49 | MS work in cable trench, cover slab, chaquered plate, clamp, cleats, brackets, etc. made from flat angle channel, tees, chequered plates 6mm thick, etc including necessary cuting to size fabricating, drilling of holes, forgeing, welding, revating, tightening with bolts and nuts with necessary washers including errection, fitting and fixing in position with all labour and materials, complete as per drawing and direction. |
| 50 | M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessaryscrews and lugs in ground floor(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.In Ground Floor. |
| 51 | Supplying fting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing.(A) In Ground floorFlash butt welded windows and ventilators(no shop priming will be allowed to facilitate inspection of workmanship)Without integrated grills. |
| 52 | (a) Fixed type steel windowes as per IS sizes with horrizontal glazing bars. |
| 53 | (b) Openable steel windows as per IS sizes with side hung shutters and horizontal glazing bars, with or outhout fixed type ventilators |
| 54 | c) Two point nose steel handle including fitting and fixing. |
| 55 | d) Aluminium peg stay 300 mm long including fitting and fixing. |
| 56 | (e) M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continuously welded with M.S. flats and bars. Mode of measurement. (The weight of grill will be determined (theoritically) from section of the grills actually used excluding the rolled steel section of the window / vent. The weight of the grill should be calculated at 7.85 gm./ cu.cm.) |
| 57 | 18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0 kg/Sq.m] |
| 58 | Extra cost of labour for prefinished and premoulded Nosingto treads of steps, railing, window sill etc. of Kota Stone. |
| 59 | Extra cost of labour for grinding Kota Stone Floor in treadsand riser of Steps |
| 60 | Supplying, fitting and fixing 18 mm. to 22 mm. thick kota stone slab in wall, dado in 15 mm thick [avg] cement mortar (1:3) including making suitable arrangement to hold the stone properly by brass / copper hooks including pointing in cement mortar (1:2) (1 cement : 2 marble dust) with admixture of pigments matching the stone shade, including grinding and polishing all complete as per direction of Engineer-in-charge including cost of materials, labour, scaffolding, staging,curing complete.[Using cement slurry for bedding @4.4 kg/Sq.m and forjointing @1.8 kg/Sq.m] |
| 61 | Supplying fitting & fixing 1st quality Ceramic Tiles in walls & floors to match with the existing works and four no of key stones (10mm) fixed with araldite at the back of each tiles and finishing the joints with white cements mixed with colouring oxide if required, to match the colour of tiles including roughening of concrete surface , if necessary, or by synthetic adhesive and grout materials etc. WallWith sand cement mortar (1:3) 15 mm thick and 2mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/sqm and joint filling using white cement slurry @ 0.20 Kg/sqm.Area of each tile upto 0.09 Sq.mOther than Coloured Decorative including white. |
| 62 | Supplying and laying chequered tiles of any shade & of approved quality with (1:1½:3) cement concrete laid in panels or patterns as directed in pavement,footpath etc. including necessary under lay 25 mm thick [avg.] cement mortar (1:3) complete in all respect with all labour and materials.[Using cement slurry @ 4.4 kg/Sq.m at back side and @ 2.4 kg/Sq.m for joint filling.](i) 25 mm. thick (red variety) |
| 63 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).i) Sal : Local |
| 64 | Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and otherfittings in ground floor(a) 35 mm thick shutters (single leaf) |
| 65 | Taking out door and window shutters and rehanging the same with old fittings. (old iron screws) |
| 66 | Wall panelling / partition with Melamine faced 3 layered flat pressed wood particle board of approved make and brand as per direction of Engineer in charge of requisite grade bonded with phenol formaldehyde synthetic rest conforming to I.S 848-1974 [ Excluding the cost of supporting frame work and teak wood battens / Lipping ] in Ground Floor.(A) Plain: Conforming to I.S:3087-1985 ) Plain: Exterior grade)(a) 9 mm. thick |
| 67 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(a) 40mm X 6mm, 125mm Length |
| 68 | Supplying fitting and fixing in position approved P.V.C. door frame(matt finish) made of extruded P.V.C. multichamber hollow section having dimensions 60mm x 50mm x2 mm. (+ - 0.2 mm), horizontal section will be joined with vertical section by galvanised steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges, one steel tube 40mm x 20mm will be inserted on one full vertical side of the frame (hinge side) as reinforcement, the frame will then be fixed in the opening with the help of P.V.C. expandable fastner wooden gutties and galvanised steel screws including cost of all materials and labour, hire charges of tools and appliances, carriage of all materials taxes and all other incidental charges complete. |
| 69 | PVC Door Shutter - 30 mm thick. Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm.x 30 mm. section with 2.0 mm.(+ - 0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each othe by self tapping screws and one solid polymeric/M.S. galvanised tubular L-shaped bracket 10 mm.X 200 mm. in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm. X 30 mm. with2.0 mm.(+ -0.2 mm.) wall thickness will be placed in the middle, reinforced by solid polymer bar of 200 mm. long at both ends and screws ftrom both sides as lock rail.the section frame will then be fitted in by PVC panels of size 100 mm.X 25 mm. with wall thickness 1.2 mm.(+ -0.2 mm.) and 2 nos. of 6 mm.bright rod will be inserted horizontally with both side check and nut system and streches where fixing of hinges /hasp bolt/tower bolt/door ring are required to be strong enough to with stand wear and tear.The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliances.Carriage of all materials taxes and all other incidental charges complete.The rate is exclusive of cost of hinges, hasp bolt, tower bolt, door ring etc. |
| 70 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (Oxidised)i) 100 mm x 50 mm x 1.25 mm |
| 71 | Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - InCharge. (Payment will be made on finished length of the work).In 10-12 Micron thickness Annodizing film.(Natural White) |
| 72 | (A) Movable door shutter |
| 73 | (a) Door frame ( top and sides ) |
| 74 | (b) Shutter: |
| 75 | Top rail- |
| 76 | Bottom rail- |
| 77 | Lock rail- |
| 78 | Door vertical- |
| 79 | Labour charges for fabrication and installation of composite door, window, partitions made from anodized extruded alloy Sections for following units:Partly glazed partly panelled or fully glazed single leaf alunminiumswing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. |
| 80 | Supplying heavy duty hydraulic double action floor spring along with top pin/set of pivots conforming to IS: 6315 or any approved make as per direction of Engineer in charge |
| 81 | Supplying concealed type heavy duty PVC headed aluminium tower bolt for double leaf doors as per approved make and brand as per direction of Engineer-in-Charge(a) 250 mm long |
| 82 | Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.i) weather gasket / wool pile for door vertical. |
| 83 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete |
| 84 | A) UPVC Pipes :110 mm. Dia. |
| 85 | B) Plain Tee : 110 mm. Dia. |
| 86 | C) Plain Y : 110 mm. Dia. |
| 87 | D) Shoe : 110 mm. Dia. |
| 88 | Supplying approved quality best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. 3mm thick (weighing 7.4 Kg/ sqm). |
| 89 | Extra for fixing glass panes in steel window. |
| 90 | Renewing worn out putty of glass panesPanes not exceeding 0.2 Sq.m |
| 91 | Supplying 4 lever mortice lock or any approved make and brand as per direction of the Engineer- in -Charge.i) 150 mm. |
| 92 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:a) 150 mm. grip x 10 mm dia rod.(With continuous plate base) |
| 93 | Iron socket bolt of approved quality fitted and fixed complete. i) 225mm long x 10mm dia bolt.(Oxydised) |
| 94 | Iron hasp bolt of approved quality fitted and fixed complete ( oxidized) with 16 mm dia rod with center bolt and round fitting.A) 300 mm long |
| 95 | Supplying best Indian sheet glass viz. hammered, fluted, ribber, pinhead etc. type including cutting to required size, setting on putty bases and fitted & fixed with nails and putty complete, ( in all floors for internal wall & upto 6m height for external wall )a) 3 mm. thick ( white ) |
| 96 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. |
| 97 | (a) 15mm dia medium quality |
| 98 | (b) 20mm dia medium quality |
| 99 | (c) 25mm dia medium quality |
| 100 | (d) 32mm dia medium quality |
| 101 | Supplying, fitting and fixing bib cock or stop cock.(i) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand). |
| 102 | (ii) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 103 | Supplying, fitting and fixing pillar cock of approved make.a) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model -Tropical / Sumthing Special of ESSCO or similar brand). |
| 104 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm. x 75 mm. X 75 mm. wooden blocks complete.470 mm X 280 mm X 340 mm |
| 105 | Supplying, fitting and fixing Half round channel with or without outlet as required set in cement conc. (6:3:1) with Jhama chips complete. ( Payment of concrete will be paid seperately ) 600 mm. x 100 mm.(a) Salt glazed stone ware |
| 106 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. (E.W.C)(a) Plastic ( hollow type ) black |
| 107 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing).a) 530mm. X 410mm. |
| 108 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.a) With P trap |
| 109 | Supplying , fitting & fixing 10 liter PVC low down cistern conforming to I.S specification with PVC fittings complete CI brackets including two coats of painting to bracket etc. |
| 110 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. 750 mm long |
| 111 | Supplying, fitting and fixing urinal flush pipe fittings of approved brand.a) C.P. urinal flush pipe fittings range of one. |
| 112 | Supplying, fitting and fixing white vitreous china best quality approved make Wash basin with C.I. brackets on 75mm X 75mm X 75mm. Wooden blocks, C.P. waste fittings of 32 mm dia, one approved quality brass C.P. pillar cock of 15mm dia, C.P. chain with rubber plug of 30 mm dia, approved quality P.V.C waste pipe with C.P. nut 32mm dia, 900 mm long approved quality P.V.C connection with heavey brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint..A) 550 mm. x 400 mm. size |
| 113 | Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets.(a) Sink only(i) 530 mm X 430 mm x 180 mm |
| 114 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm. thick with silvering as per I.S.I specifications supported on fiber glass frame of any colour, frame size 550mm x 400mm.A) size 550mm x 400mm. |
| 115 | Supplying, fitting and fixing towel rail with two brackets.(a) C.P. over brass(i) 25 mm dia. and 450 mm long |
| 116 | Renewing,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.750 mm long |
| 117 | Supplying bubble free float glass of approved make and brand conforming to I.S. 2835-1987 |
| 118 | (a) 4 mm thick plain glass |
| 119 | (b) 5mm thick thick plain glass |
| 120 | Sealing new expansion joint with Elastomeric Polysulphide Sealant of gap size 50mm X 25mm Including cleaning of the expansion joint thoroughly, mending of edges & surface, placing 50mm dia Backer rod as back up material with the cost of materials, labours, & all other incidental charges as per manufacturer's specification & direction of Engineer-incharge. |
| 121 | Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification. |
| 122 | Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than 150mm apart complete in all respect as per design including cost ofall labour and materials Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysNov 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender