Tender For Special Repair To Building No. P-07, Construction Of Wall Behind Balvatika Assembly Stage At Aps, Provn Of Seprate Chain Link Fence & Gate At Aps And 02 X Single Toilet For Garage At Patiala Under Ge (South) Patiala
Tender Value
Ref. Documents
Estimated cost
Bid Submission
03 Nov 2026
18 days left
EMD
92100
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Patiala → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Building No. P-07, Construction Of Wall Behind Balvatika Assembly Stage At Aps, Provn Of Seprate Chain Link Fence & Gate At Aps And 02 X Single Toilet For Garage At Patiala Under Ge (South) Patiala
BOQ
| Sl. No. | Item Description |
| 1 | 'Notes: (i) Please refer Schedule 'A' Notes of tender documents. |
| 2 | Dismantling of brick tiles or terracing tiles single layers on roofs complete all as specified and directed. |
| 3 | Demolition of mud phuska on roof any thickness complete all as specified and directed. |
| 4 | M&L for roughening surfaces of old concrete floor/roof by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed. |
| 5 | M&L for PCC 1:3:6, type C-0 using 12.5mm graded stone aggregates as in padding over roof, minimum thickness at khurra as 25mm to maintain a slope of 1:100, complete all as specified and directed. |
| 6 | M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed. |
| 7 | M&L for providing and laying 3mm thick APP (Atactic Polyproplene Polymer) modified prefabricated five layer, weight not less than 4.0 Kg/Sqm water proofing membrane black finished, reinforced with non-woven polyster matt make as approved including of a coat of bitumen primer @ 0.40 ltr/Sqm by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, 3mm th 5 layered APP membrane shall be laid using butane torch and sealling all joints etc after the surface complete as per standard practice as per manufacturers instructions. The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength inlongitueinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only complete all as specified and directed. |
| 8 | M&L for Plain Cement Concrete tiles 25cm x 25cm x 22-25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 9 | M&L for Plain cement concrete 1:2:4 type B-0 using 12.5mm graded mechanically crushed stone aggregate as in roof kerbs or mud stops and benching, rounded or chamfered on edges, coving shall be 150 mm in radius mixed with acrylic based polymer water proofing compound complete all as specified and directed. Note: WPC shall be paid separately |
| 10 | Taking down of Eaves gulter/rain water pipe(AC rain water pipe /SWG pipe line of any size or pattern), including at fittings, heads, shoes, bends, swan-necks, etc., including cleaning for refuxing or removal from site (measured overall as fixed along the centre line including fitting and accessories) complete all as specified and directed. |
| 11 | S&F PVC (SWR) Type ‘B’, 160 mm nominal outside diameter confirming to IS : 13592-1992 single socketed in any length including jointing with lubricant/ PVC cement solvent as per manufacturer’s instruction”, fixed to walls with MS flat iron clamps of size 25 x 3mm, bolts, washers, nuts, nails etc, complete all as specified and as directed. Note: (i) MS flat iron clamps will be measured and paid separately in respective item.(ii) Clamps will be measured and paid separately. |
| 12 | S&F PVC (SWR) bends, 160 mm dia confirming to IS : 14735-99 and jointing with lubricant/ PVC cement solvent as per manufacturer’s instruction”, complete all as specified and as directed. |
| 13 | S&F for MS Clamps, Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay) and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 14 | Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to faciliate demolition) complete all as specified and directed. |
| 15 | M&L for Reinforced Cement Concrete 1:2:4 type B-1 using 20 mm graded aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork complete all as specified and directed. |
| 16 | M&L for Reinforced Cement Concrete (Nominal Mix) 1:2:4, Type B1 (using 20mm graded stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 17 | Form work rough finished to sides and soffits of roof beams, lintels cantilevers etc complete all as specified and directed. |
| 18 | Form work rough finished to soffits of suspended slabs such as roof slabs not exc 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 19 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 20 | S&F Mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed. |
| 21 | Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins, arches, pillars etc complete all as specified and directed. |
| 22 | M&L for brick work with old size Fly ash bricks minimum class designation 100 straight or curved on plan exceeding 6m mean raidus bulit in C:M 1:6 complete all as specified and directed. |
| 23 | Taking down cement plaster of any description, any thickness from external/internal surfaces of walls/soffits/ceilings etc. incl raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and directed. |
| 24 | M&L for cement plastering 15mm thick in cement mortar 1:4 including mixing of liquid water proofing compound (@2% by weight or as per manufacturer's instructions whichever is higher) to brick work or concrete surfaces or in chajjas/parapet walls etc finished even and fair without using extra cement complete all as specified and directed.Note : WPC will be measured and paid separately. |
| 25 | Supply only integral liquid water proofing compound complete all as specified and directed. |
| 26 | M&L for 10mm thick cement plastering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed. |
| 27 | M&L for 5 mm thick cement plastering in cement mortar 1:3 on fair faces of concrete ceiling surfaces finished fair & even without using extra cement complete all as specified and directed. |
| 28 | M&L for complete removal of existing treatment on wall/roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding paper of appropriate grit to make suraface clean , free from dust, loose paint etc by skilled labour complete all as specified and directed. Note: Standing of suraface to be done by mechanical sander with 1500-2700rpm, with internal dust extraction system for clean environment certified by paint manfacturer.Proper masking to be carried out before primer and paint application. |
| 29 | M&L for applying acrylic thick wall care putty on external/internal surfaces of walls/ceilings/soffits etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer -In- Charge through site order. |
| 30 | M&L for preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade, @ 5 Sqm/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 Sqm/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer and using fully automatic airless spray machine having flow speed of min. 1 lit/minute and pressure of 3300psi complete all as specified and directed. |
| 31 | M&L for preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) @ 10 Sqm/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 Sqm/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer and using fully automatic airless spray machine having flow speed of minimum 1 ltr/minute and pressure of 3300PSI complete all as specified and directed. |
| 32 | M&L for preparation of surfaces and applying 02 coats of interior emulsion paint (white shade) @ 10 Sqm/litre/2 coats to ceilings surfaces over & including a coat of interior primer @ 10 Sqm/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer and using fully automatic airless spray machine having flow speed of min. 1 ltr/minute and pressure of 3300PSI complete all as specified and directed. |
| 33 | Note for item No. 30 to 32(i) The contractor shall submit manufacturer generated 04 years warranty card for each buildings treated/ painted during submission of Final Bill and guarantee amount @ 5% will be kept as reserve till completion of warranty period and will be released thereafter. Any deterioration during the warranty period will be rectified by the contractor without any financial effect within a week.(ii) The work shall be executed by the contractor as per MoU from authorised applicator through manufacturer of the materials like Exterior/Interior Paint, Putty etc after approval by the GE.(iii) The Lowest bidder shall submit the \\"Memoradum of Understanding\\" (MOU) as per format given in Annexure ‘A’ after Schedule 'A' Notes with at least one of the manufacturers mentioned in the contract, after acceptance of the bid but before commencement of the work. If he fails to submit the same as referred above, his contract shall liable to be cancelled.(iv) Cost of T&P and a scaffolding/Jhoola, trestles, ladders, cradeles, centring, crane, boom lifts/ crane of any type and shuttering etc necessary for execution of work and protective measures complete upto all height shall be deemed to be included under respective item.(v) Cost of temporary covering to all joinery items (like doors, windows, window panes), sanitary fittings, dado/skirting, floors, etc to protect them from splashes.(vi) Packing material/empty Buckets will not be handed over to the contractor and will be property of the MES and will be disposed off with the permission of the Engineer-in-Charge and GE.(vii) Washing floors, cleaning glass, joinery , electric fittings , wirings etc. Drops and splashes of paint to be cleaned to the entire satisfaction of Engineer-in-Charge.(viii) Sample patch of 10Sqm be prepared and shall be got approved from GE prior to carrying out further work.(ix) Cost of removing of nails, making good holes, filling of cracks with acrylic crack filler paste etc shall be deemed to be included under respective item.(x) Work in patches and in narrow / widths, bands, cornices, pilasters etc and cutting in edge of line where necessary. |
| 34 | Dismantling, floor, hearth or wall tiling including CM bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed |
| 35 | M&L for Full Body Vitrified Tiles joint free premium quality coloured tiles 600 X 600 mm and 8-10 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed. |
| 36 | M&L for mat finish anti skid vitrified tile joint free premium quality coloured tiles 600 X 600 mm and 8-10 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 15 mm thick screed in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed. |
| 37 | M&L for Ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.Note : Dado should be flushed with the wall plastering. |
| 38 | M&L for Machine cut kota stone slab (nearest to 58cmx58cm in size) flooring 18mm (+ 2mm) thick laid over and including 20-22 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing incl 100mm wide border of Baroda Green Marble including bull nosing complete all as specified and directed. |
| 39 | M&L for Machine cut mirror polish, kota stone slab, 18mm (+ 2mm) thick as in risers of step, skirting, dado etc and including 10 mm thick rendering in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 40 | M&L for pre-polished Baroda Green marble, machine cut as in floorings/ shelves/ steps/ cills/ jambs/ skirting/ border only in tile flooring and the like works and flooring etc, 15-16 mm thick including bull-nose the exposed sides/lengths, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab for fixing on concrete surfaces or with suitable adhesive for fixing incl 100mm wide border of White Marble in flooring complete all as specified and directed.Note : Single piece should be used in steps/cills/jambs/shelves. |
| 41 | M&L for Granite (Jet Black colour/shade-South Indian) of any type machine cut as in flooring, shelves/steps/counter tops, 18-20 mm thick, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing and bull nose on exposed sides/lengths complete all as specified and directed.Note : Single piece should be used in steps/cills/jambs/shelves. |
| 42 | Demolition of cement concrete un-reinforced in ground floors and pavings n. exc 15cm thickness complete all as specified and directed. |
| 43 | M&L for 100mm thick cement concrete work 1:4:8 type D-2 in sub-case to flooring etc complete all as specified and directed. |
| 44 | M&L for 25mm thick cement cocnrete 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate ) as in flooring complete all as specified and directed. |
| 45 | M&L for Hardcore of broken stone or boulder gauge not exc. 63 mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface all as specified and directed. |
| 46 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etclaid bedded and pointed in any mortar complete including removal of entire debris as ordered outside MD land complete all as specified and directed. |
| 47 | M&L for pre-polished machine pressed rubber moulded precast cement concrete interlocking modular paver block in combo design of size 200x100x60mm & 100x100x60mm or 300x200x60mm, 200x200x60mm & 200x100x60mm of approved shades of colour/pigment in approved pattern with minimum M-35 Grade including over including 25mm thick layer of sand cushion complete all as specified and directed. |
| 48 | M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 49 | M&L for cement concrete (1:3:6) type C-1 (using 20 mm graded stone aggregate) 50 mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints and filling the same with polyureathene complete all as specified and directed. |
| 50 | Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good to disturbed surfaces complete incl ventilators including reqd shape for hold fast block for new frame complete all as specified and directed. |
| 51 | Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed. |
| 52 | S&F door frames made of PPGI sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, lock strike plate, hold fast etc., complete all as specified, size 105 x 60mm and incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed.Note : Mullions and Transom will be measured and paid for each side separately. |
| 53 | S&F door frames made of PPGI sheet of 1.20 mm thickness for doors and windows with one or more rebates including necessary fixing lugs, lock strike plate, hold fast etc., complete all as specified, size 125 x 60mm and incl cutting holes and making good reqd shape for hold fast block for new frame incl complete all as specified and directed.Note : Mullions and Transom will be measured and paid for each side separately. |
| 54 | S&F factory made 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including exposed surfaces finished with external teak wood lipping, 6 mm thick fixed with nails complete all as specified and directed. |
| 55 | S&F 35mm thick glazed and skelton shutters of 2nd class hard wood as in doors (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part I, Section 8, clause 8.24 (a);, kiln seasoned and chemically pressure treated complete all as specified and directed.Note : Glass or wire cloth, etc. in panels or sash squares shall be measured separately. |
| 56 | S&F 30mm thick glazed and skelton shutters of 2nd class hard wood as in windows/ventilators open rebated and divided to receive glass, gauze etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part I, Section 8, clause 8.24 (b);, kiln seasoned and chemically pressure treated complete all as specified and directed.Note : Glass or wire cloth, etc. in panels or sash squares shall be measured separately. |
| 57 | M&L for providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beed 20mm size with and complete fixed in all respect as specified and directed. |
| 58 | S&F, 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 59 | S&F, 125 aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 100mm complete all as specified and directed. |
| 60 | S&F 150 mm long extruded aluminium alloy handle, fabricated type, single body, anodised complete all as specified and directed. |
| 61 | S&F125 mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 62 | S&F Floor door stopper of aluminium alloy body with rubber bottom and tongue, anodised, with 140mm over all length complete all as specified and directed. |
| 63 | S&F in repair 300 mm long mild steel ordinary rat tail rod pattern spring including roller and roller plate for doors complete all as specified and directed. |
| 64 | S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 65 | S&F 5.0 mm thick clear sheet glass for glazing works etc fixed with aluminium beads/uPVC windows any size of pane complete all as specified and directed. |
| 66 | M&L 5mm thick frosted glass not exc 0.50 Sqm in each pane as in ventilators/ windows/ doors fixed in any metal frame work/ aluminium / uPVC joinery complete all as specified and directed. |
| 67 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 68 | Dismantling of AC corrugated or semi corrugated sheets including ridges in roof coverings complete all as specified and directed. |
| 69 | M&L for prepainted galvalume aluminum zinc coating GI based semi corrugated / profile steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu screw as per manufacturar instruction complete all as specified and directed. |
| 70 | S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in ridge etc, fixed with self tapping screws complete all as specified and directed. |
| 71 | Dismantling wrought iron or mild steel work of any description any position complete all as specified and directed. |
| 72 | S&F MS hollow rectangular/square/circular tubes/pipes of YST 310 Grade as in frame work for Framed work as in doors or gates/ roofs/ rafters/ purlins/ chajjas/ trusses/ columns/ struts etc and like similar items etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete and similar work complete all as specified and directed. |
| 73 | S&F, framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde E-165 complete all as specified and directed. |
| 74 | S&F Plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk ) and forming holes with riveted, bolted or welded attachment Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed. |
| 75 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete all as specified and directed. |
| 76 | S&F anodised aluminium snap grid frame work (size of grid 605x605mm) for false ceiling all as specified including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.l. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 77 | M&L 12 to 12.50mm thick semi-perforated/pin holed particle board/tiles, 600x600 ± 5 mm in size fixed in false ceiling as per manufacturer's instructions to existing frame work or on snap grid as in repairs complete all as specified. |
| 78 | S&F in repairs 25 mm dia decorative stainless steel curtain rails fixed to SS bulb type brackets complete all specified and directed. |
| 79 | M&L for Stainless steel sheet of approved thickness of Grade 304 for sign boards and all similar works including Rubbing/Polishing fixed to frame work complete all as specified and directed. |
| 80 | S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 81 | S&F vitreous china premium/1st quality wash basin (under counter), white, size 580x430 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified and directed.Note : The items for counter will be measured and paid separately. |
| 82 | S&F in repair CP Wall mounted basin spout and operating lever quarter turn consisting of exposed part and concealed part complete all as specified and directed. |
| 83 | S&F in repair 15 mm fancy type chromium plated quarter turn angle cock/valve with CP wall flange cast copper alloy screwed down high pressure suitable for 15mm bore pipe or union including taking down old unserviceable existing one complete all as specified and directed. |
| 84 | S&F in repairs 15 mm fancy type chromium plated quarter turn bib tap of long body with CP wall flange cast copper alloy with crutch or butterfly handles screwed down high pressure suitable for 15mm bore pipe or union including taking down old unserviceable existing one complete all as specified and directed. |
| 85 | S&F CP waste couplings 32mm size full thread with 80mm height complete fixed in position complete all as specified and directed. |
| 86 | S&F in repairs 20mm dia towel rail brass Chromium Plated 60 cm long between flanges and including all accessories like brackets/screws etc as recommended by manufacturer and complete fixed in position complete all as specified and directed. |
| 87 | S&F in repair soap dish, stainless steel of suitable size to accommodate soap, tooth brush glass and tooth paste complete all as directed and specified. |
| 88 | S&F in repair stainless steel grating 125x125 mm/ 150x150mm size square shaped with self locking arangement for floor trap with or without hole as required fixed in position complete all as specified and directed. |
| 89 | S&F 450mm long braided hose/PVC connection with 15mm brass nuts complete all as directed and specified. |
| 90 | S&F in repairs PVC Flexible Waste Pipe with Chrome Finish (min. 30 Inches) of minimum weight 148 gms (± 5%) heavy duty complete all as specified and directed. |
| 91 | S&F in repair 5mm thick looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish without any beading, including ends/edges of the mirror to be tapered etched smooth finish etc.complete fixed in position all as specified and directed. |
| 92 | S&F in repair 40 mm bore PVC high density polyethylene pipes (HDPE) of pressure rating 6 Kgf/ Sqcm., single socketed in any length with rubber ring joints using solvent cement as per maunfacture instruction, including bends/tee/elbow etc.fixed to walls, ceilings or in floors complete all as specified and directed. |
| 93 | S&F in repair 32 mm bore PVC high density polyethylene pipes (HDPE) of pressure rating 6 Kgf/ Sqcm., single socketed in any length with rubber ring joints using solvent cement as per maunfacture instruction, including bends/tee/elbow etc.fixed to walls, ceilings or in floors complete all as specified and directed. |
| 94 | Taking up or down existing steel tubing and connections, 25mm bore complete all as directed and specified. |
| 95 | S&F 25mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as directed and specified. |
| 96 | Taking up or down existing steel tubing and connections, 15 mm bore complete all as directed and specified. |
| 97 | S&F 20mm (OD 22.20mm) CPVC pipes SDR 11, class-1 for potable hot and cold water distribution supplies lead free confirming to IS-15778 laid on walls/ceiling or laying in floors jointed with suitable CPVC solvent cement of same manufacturer and including all CPVC SDR 11 fittings as required and suitable for fixing 15mm CP faucets/ fixtures complete all as specified and directed. |
| 98 | S&F Female Brass Threaded Adaptor (FTA/ FBTA) for 20mm dia CPVC pipe complete all as specified and directed. |
| 99 | S&F Brass elbow (3/4 x 1/2) for 20mm dia CPVC pipes complete all as specified and directed. |
| 100 | Dismantling existing water tank and S&F ISI marked doubled layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top / cover) 1000 Ltrs capacity hoisted and fixed in position all as specified including 20 mm dia brass float valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe and including GI nipple/union of 20mm bore to connect GI tubing to PVC water tank complete all as specified and directed. |
| 101 | S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and complete all as specified and directed. |
| 102 | S&F in repair 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and complete all as specified and directed. |
| 103 | Taking down sewage pipe of in any position/size/description complete all as specified and directed. |
| 104 | S&F uPVC (SWR) Type-B pipe single socket 110mm bore confirming to IS 13592-92 in any length with including jointing with lubricant/ PVC cement solvent as per manufacturer’s instruction to UPVC waste pipe, fixed to wall, including stack clamps out of 50x5 mm flat and 16 mm dia iron stays, including bolts and nuts etc and making necessary connections complete all as specified and as directed.” |
| 105 | S&F uPVC (SWR) Type-B pipe single socket 110mm bore confirming to IS 13592-92 in any length with including jointing with lubricant/ PVC cement solvent as per manufacturer’s instruction to UPVC waste pipe, laid in trenches/floor and making necessary connections complete all as specified and as directed.” |
| 106 | S&F uPVC (SWR) Type-B pipe” single socket 75mm bore confirming to IS 13592-92 in any length “with lubricant/ PVC cement solvent as per manufacturer’s instruction fixed to wall ,including stack clamps out of 50x5 mm flat and 16 mm dia iron stays, including bolts and nuts etc and making necessary connections, complete all as specified and as directed. |
| 107 | S&F uPVC (SWR) Type-B pipe” single socket 75mm bore confirming to IS 13592-92 in any length “with lubricant/ PVC cement solvent as per manufacturer’s instruction laid in trenches/floor and making necessary connections, complete all as specified and directed. |
| 108 | Taking down bends/floor traps/nahani traps/tee/branch pieces/cowls etc of in any position/size/description complete all as specified and directed. |
| 109 | S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ” bend 110mm bore pipes (any radius) with access door fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction” complete all as specified and directed. |
| 110 | S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ”bend 75mm bore pipes (any radius) with access door fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction” complete all as specified and directed. Please Enable Macros to View BoQ information |
| 111 | S&F uPVC (SWR) confirming to IS : 14735-99 and as per international standards ”bend 75mm bore pipes (any radius) with access door fixed “with lubricant/ PVC cement solvent as per manufacturer’s instruction” complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysNov 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender