Tender For Construction Of New Design Modular Fence Along The Boundary Of 7Th Bn, Itbp, Mirthi Pithoragarh Ukd
Tender Value
6.86 Crore
Estimated cost
Bid Submission
03 Nov 2026
7 days left
EMD
13.72 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pithoragarh → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of New Design Modular Fence Along The Boundary Of 7Th Bn, Itbp, Mirthi Pithoragarh Ukd
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:Channels, angles, tees and flats |
| 2 | Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead. |
| 3 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 4 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 5 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.All kinds of soil |
| 6 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)PCC (1:5:10) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominalsize derived from natural sources). |
| 9 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 10 | Random rubble masonry with hard stone in superstructure above plinthlevel and upto floor five level, including leveling up with cement concrete1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mmnominal size) at window sills, ceiling level and the like |
| 11 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete. |
| 13 | 6 mm cement plaster of mix 1:3 (1 cement : 3 fine sand) |
| 14 | 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand) |
| 15 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 16 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 17 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 18 | Providing & Fixing High security fencing with CHS post having dimension 76 x 3.4 mm with Hot dip galvanised coating to minimum 360 GSM and thermoplast coating of 200 microns- 250 microns ,total length of post 3.40 m including 700 mm embedded in cement concrete block of required size (as per drawing & will be paid separately) with straining & intermediate Y-arm as per specified drawing made up of MS angle 50x50x5 mm with cap at bottom & duly coated with thermoplast coating of 200 microns-250 microns and properly connected with the post with the help of M8 security nut & bolt & welding. (Cost for Fitting accessories will be paid separately) |
| 19 | Supplying & fixing high security/Anti climb weld mesh panel Produced by electrical resistance galvanized wires and subsequently powder coated that are reinforced by means V-shapes in horizontal direction of the panel of required size including overlapping of panels as per specified drawing having Mesh wire diameter: 4.00 mm (+/- 0.05 mm), Mesh size:955x2667 mm with zinc coating on Wire 40 GSM & 120 to 160 microns of powder coating (Dual Coated) fixed to the CHS post as complete as per drawing and direction of Engineer-In-charge.(Cost for Fitting accessories will be paid separately) |
| 20 | Providing, laying & fixing of Razor wire of Tear Blade profile having blade thickness 0.45 mm & core wire diameter 3.5 mm duly galvanised to minimum 270 gsm and having tensile strength of 1400-1500 N per sq mm complete as per drawing and direction of Engineer-In-charge.(Cost for Fitting accessories will be paid separately) |
| 21 | Providing & fixing punched tape concertina coil of dia 850 mm with 56 loops stretchable for 10 meter on top of Y-arm of the fence and with razor wire by atleast 5 clips per loop having minimum galvanising to 275 GSM with Tear blade profile having blade thickness 0.45 with galvanised core wire diameter 3.5 mm fixed to existing post with the help of proper fixing accsessories.(Cost for Fitting accessories will be paid separately). |
| 22 | Supplying omega clamp made with MS and Hot Dip galvanised to 350 GSM minimum & all fastners with SS 304 material with unbreakable security nuts & other fitting accessories. |
| 23 | Supply & installation of Semi Integrated 12 Watt White LED type Solar Street Light with 6MTR Hight, 65 mm dia/3.6 mm thick Steel tube pole for street light. Solar Street Light (LED based) consist of white LED luminaire ( LED + Driver) along with Solar PV modules and LiFePo4 12.8 V (nominal), 30 Ah at STC (1 day autonomy) capacity battery, necessary control electronics, interconnecting wires / cables, module mounting structures and etc. certified by MNRE/ NABL accredited labs and as per the direction of Engineer-in-charge. (GeM Rate, Quotation enclosed) |
| 24 | Supply & installation of Semi Integrated 12 Watt White LED type Solar Street Light with 6MTR Hight, 65 mm dia/3.6 mm thick Steel tube pole for street light. Solar Street Light (LED based) consist of white LED luminaire ( LED + Driver) along with Solar PV modules and LiFePo4 12.8 V (nominal), 30 Ah at STC (1 day autonomy) capacity battery, necessary control electronics, interconnecting wires / cables, module mounting structures and etc. certified by MNRE/ NABL accredited labs and as per the direction of Engineer-in-charge. (GeM Rate, Quotation enclosed) |
| 25 | Credit for dismantled/unserviceable materials to be taken by contractor dismantled/unserviceables angle iron (steel work in single sections) including all fittings. |
| 26 | Credit for dismantled/unserviceable materials to be taken by contractor dismantled/unserviceables barbed wire including all fittings. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysNov 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender