Tender For Redevelopment Of Saima Lodge At Gandacherra
Tender Value
Ref. Documents
Estimated cost
Bid Submission
10 Nov 2026
27 days left
EMD
34.67 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhalai → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Redevelopment Of Saima Lodge At Gandacherra
BOQ
| Sl. No. | Item Description |
| 1 | Bill No. I: Earthwork |
| 2 | Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 3 | Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. All kinds of soil |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. |
| 5 | Extra rates for quantities of works, executed:In or under water and/ or liquid mud, including pumping out water as required |
| 6 | In or under foul position, including pumping out water as required |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.All kinds of soil |
| 8 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 9 | Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 10 | Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termite treatment as per IS: 6313 (Part III)- Latest revision (excluding the cost of chemical emulsion):Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 11 | Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.With hlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 12 | Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 13 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 fine sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 14 | Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45° and plugging them with cement mortar 1:2 (1 cement: 2 fine sand) to the full depth of the hole: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 15 | Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos / Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45° at 150 mm centre to centre and sealing the same.The work will be carried out as per IS: 6313 [Latest Revision].Under the Insecticides Rule 1971: 10(3A) any person who desires to undertake pest control operations will be a Licence holder. The agency must complying with all safety health and welfare regulations, appertaining to staff and work people employed on the site.Keeping the site free from debris arising from the works during the work and leave the site free from debris on completion of work to the satisfaction of the Owner.The agency shall give a 3-year service guarntee in writing supplemented by a seperate and unilateral guarantee from the specialised agency for the job to keep the building free of termites for the specified period at no extra cost of the Owner. SoR |
| 16 | Bill No. II: Cement Concrete Work |
| 17 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All Work upto Plinth Level1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 18 | Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).DPC 40 mm thick |
| 19 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of aproved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 20 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 21 | Bill No. III: Reinforced Cement Concrete Work |
| 22 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All Work upto Plinth Level1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 23 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 24 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 25 | Providing and laying in position design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge.(Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth levelReinforced cement concrete grade M-25 using 418 kg of cement per cum |
| 26 | Providing and laying in position design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge.(Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto Floor five levelReinforced cement concrete grade M-25 using 418 kg of cement per cum |
| 27 | Centering, Shuttering including struttings, propping etc and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 28 | Foundations, footings, bases for columns etc. for mass concrete with steel formwork |
| 29 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply |
| 30 | Suspended floors, roofs, landings, balconies and access platform with timber planks |
| 31 | Suspended floors, roofs, landings, balconies and access platform with M.S. plates and props |
| 32 | Lintel beams, plinth beams, girders, bressumers & cantilevers with 12 mm shuttering ply |
| 33 | Columns, Pillars, Piers, Abutments, Posts and Struts with M.S. shutters |
| 34 | Stairs (excluding landings) except spiral-staircases with wooden plank |
| 35 | Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof: Suspended floors, roofs, landing, beams and balconies (Plan area to be measured). |
| 36 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 37 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 38 | Bill No. IV: Brick Work |
| 39 | First class brick work in foundation and plinth including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 40 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 41 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 42 | Providing and fixing Galvanized chicken mesh (24 guage, 12 mm size) properly stretched and nailed ensuring equal thickness of plaster at junction of masonry work and concrete members. |
| 43 | Bill No. V: Wood Work & PVC |
| 44 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :Karai wood |
| 45 | Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory/ windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 × 12 mm for fixing panelling and or glazing as per direction of Engineer-In-Charge.Local Teak wood35 mm thick shutters |
| 46 | Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B) including ISI marked black enamelled M.S. butt hinges with necessary screws as per directions of Engineer-incharge and panelling with panels of:12 mm thick one side prelaminated (with particle board decorative lamination on other sides) and balancing lamination grade - 1 medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and prelamination conforming to IS : 12823 Grade - 1, Type II marked : |
| 47 | Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :125 × 65 × 2.12 mm |
| 48 | 100 × 58 × 1.90 mm |
| 49 | 75 × 47 × 1.70 mm |
| 50 | 50 × 37 × 1.50 mm |
| 51 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :125 x 64 x 1.90 mm |
| 52 | 100 X 58 X 1.90 mm |
| 53 | 75 x 47 x 1.80 mm |
| 54 | 50 x 37 x 1.50 mm |
| 55 | Providing and fixing oxidised M.S. Safety chain with necessary fixtures for doors. (Weighing not less than 450 gms.) |
| 56 | Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : 250 x 10 mm |
| 57 | 200x10 mm |
| 58 | 150x10 mm |
| 59 | 100x10 mm |
| 60 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality) |
| 61 | Providing and fixing bright finished brass night latch including necessary screws etc. complete (best make of approved quality). |
| 62 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 63 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete |
| 64 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :125 mm |
| 65 | Providing and fixing factory made UPVC door frame made of UPVC extruded, section having an overall dimension, as below (tolerance +/- 1mm) with wall thickness 2.0mm+/- 02mm. corners of the door frame to be jointed with galvanized brackets and stainless screws, joint mitred and plastic wilded. The hinge side vertical of the frames reinforced by galvanized MS tube of size 19 × 19 mm and 1 mm +/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-In-Charge.Extruded section Profile size 48x40 mm. |
| 66 | Providing and fixing to existing door frames.24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised /plastic brackets of size 75×220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanised MS tube of size 20×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \\"H\\" Section, a UPVC hollow section of size 100×24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galvanised MS \\"U\\" cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontaly 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter). |
| 67 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19×19mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall usuing MS screws of 65/100 mm size complete as per manufacturers' specification and direction of Engineer-In-Charge. |
| 68 | Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20 mm dia |
| 69 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. Fixed to steel windows by welding |
| 70 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 71 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 72 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm |
| 73 | 200 x 10 mm |
| 74 | 150 x 10 mm |
| 75 | Providing and fixing chromium plated brass handles with necessary screws etc. complete:125 mm |
| 76 | 100 mm |
| 77 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper |
| 78 | Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality) |
| 79 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:- 80xl.25mm M.S. laths with 1.25 mm thick top cover. |
| 80 | Providing and fixing ball bearing for rolling shutters (exceeding 10 sqm area) of approved make complete as required. |
| 81 | Extra for providing & fixing mechanical device chain and crank operation for operating rolling shutters of approved make complete as required:- Exceeding 10.00 sqm and upto 16.80 sqm in the area. |
| 82 | Exceeding 16.80 sqm in the area. |
| 83 | Extra for providing & fixing grilled rolling shutters manufactured out of 8 mm dia. M.S. plain bar instead of laths as per design approved by Engineer-in-charge (area of grill to be measured) complete as required. |
| 84 | Providing and fixing aluminium tubular handle bar of 32 mm outer dia, 3.0 mm thick and 2100 mm long with Stainless Steel screws etc. of approved quality complete as per direction of Engineer-in-charge:-Polyester powder coated aluminium minimum thickness 50 micron. |
| 85 | Bill No. VI: Aluminium Work & Structural Glazing |
| 86 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-For fixed portion of approved quality:-Powder coated aluminium ( minimum thickness of powder coating of 50 micron ). |
| 87 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):-Powder coated aluminium ( minimum thickness of powder coating of 50 micron ). |
| 88 | Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (both primary and secondary sealant) of approved quality etc.complete as per specification, drawing and direction of Engineer-incharge |
| 89 | Filling the gap in between aluminium frame and adjacent RCC/brick work by providing weather silicon sealantover backer rod of approved quality etc. complete as perarchitectural drawing and direction of the Engineer-incharge:- (i) Upto 5 mm depth and 5 mm width. |
| 90 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-Polyester powder coated aluminium minimum thickness 50 micron. |
| 91 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 92 | Providing and fixing aluminium tubular handle bar of 32mm outer dia, 3.0 mm thick and 2100 mm long withStainless Steel screws etc. of approved quality completeas per direction of Engineer-in-charge:-Polyester powder coated aluminium minimum thickness 50 micron. |
| 93 | Float glass sheet of nominal thickness 8 mm.(weight not less than 20 kg/sqm). |
| 94 | Float glass sheet of nominal thickness 4 mm (weight not less than 10kg/sqm). |
| 95 | Float glass sheet of nominal thickness 5.5 mm.(weight not less than 13.50 kg/sqm). |
| 96 | Frosted glass sheet of nominal thickness 4 mm (weighing not less than 10 kg/sqm) |
| 97 | Glass sheet (Pin headed) 4 mm thick |
| 98 | Toughened glass 12 mm thickness |
| 99 | Bill No. VII: Flooring |
| 100 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles300 x 300mm in all shades and designs |
| 101 | 600 mm x 600 mm in all shades and designs 1st class quality ceramic floor Porcelain tiles |
| 102 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.Double charged Stainfree vitrified tiles (Glossy)Size of tile 600 mm x 600 mm |
| 103 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.450 mm X 300 mm in all shades and design |
| 104 | 600 mm X 300 mm in all shades and design |
| 105 | Providing and laying flamed finish Granite stoneflooring in required design and patterns, in linearas well as curvilinear portions of the building allcomplete as per the architectural drawings withFlamed finish granite stone slab Jet Black, CherryRed, Elite Brown, Cat Eye or equivalent over 20mm (average) thick base of cement mortar 1:4 (1cement : 4 fine sand) laid and jointed with cementslurry and pointing with white cement slurryadmixed with pigment of matching shadeincluding rubbing, curing and polishing etc. allcomplete as specified and as directed by theEngineer-in-Charge-18 mm thick stone slab. |
| 106 | 38 mm thick wood block flooring of local teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished etc. all complete as per direction of Engineer-in-charge. |
| 107 | Providing & fixing in position Phenol bonded Bamboowood flooring with planks of sizes 14mm thick, 1800mm length (minimum) and 130 mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded poly ethylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm x 44mm, wherever required. The bomboo wood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, etc. all complete as per direction of Engineer-in-charge. |
| 108 | Providing and fixing coloured self adhesive PU - Tactile tiles, ground surface indicators (made of Polyurethane) grade 70/85 of size 300x300mm. for guiding/warning to the visualy impaired visitors in the entre/side of the pedestrian/ approch pathway as per design/specification and Harmonised guidelines complete in all respect as per the direction of the Engineer-in-charge. |
| 109 | Supply & installation of EPDM flooring |
| 110 | 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. Red sand stone |
| 111 | Bill No. VIII:ROOFING |
| 112 | Supply & installation of pre-painted Galvalume sheetsfor roofing/cladding (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) in550mpa steel grade, made out of Cold Rolled Steelcoated with Zinc-Aluminium alloy coating of 43.5% Zn,55% Al and 1.5% Silicon confirming to ASTMA792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, topcoated of modified polyester of 20 micron, back sidecoat of 5 micron, having epoxy primer coat of 5 micronon both side. Sheet should have protective guard filmof 25 microns minimum to avoid scratches while transportation and should be supplied in singlelength upto 12 metre or as desired by Engineer-incharge.The sheet shall be fixed using self drilling/self tapping screws of size (5.5x 55mm) with EPDMwashers filled with white lead complete upto anypitch in horizontal/ vertical or curved surfacesexcluding the cost of purlins, rafters and trusses andincluding cutting to size and shape wherever requiredand as per direction of Engineer-in-charge.0.80mm thickness |
| 113 | Supply & installation of pre-painted Galvalume sheetsroofing accessories in 550mpa steel steel grade, madeout of Cold rolled steel coated with Zinc-Aluminiumalloy coating of 43.5% Zn, 55% Al and 1.5% Siliconconfirming to AASTM A792/A792M and AS1397, Alloycoating AZ150/AZ70, colour coated with high qualitypolyester coating, top coated of modified polyester of 20micron, back side coat of 5 micron, having epoxy primercoat of 5 micron on both side etc. complete as perdirection of Engineer-in-charge. Sheet should haveprotective guard film of 25 microns minimum toavoid scratches while transportation. Sheet shouldhave protective guard film of 25 microns minimumto avoid scratches while transportation. The sheetshall be fixed using self drilling /self tapping screwswith EPDM washers complete forRidges/Valley/Gutter/Flashing of width 610mm:0.80mm thickness |
| 114 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) asper IS : 277 and consisting of angle cleats of size 25 mmwide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mmdia bolts, other flange of cleat fixed to the angle hangers of25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips madeout of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall /partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for lightfittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board |
| 115 | Supply and Installation of Tensile Walkway Canopy in fabricated MS structureas as per specification and approval of Engineer-in-Charge |
| 116 | Bill No. IX: Steel Work |
| 117 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes |
| 118 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 119 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-In grating, frames, guard bar, railing, brackets, gates and similar works, all complete.In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 120 | Bill No. X: Finishing Work |
| 121 | 12 mm Cement PlasterCement mortar 1:4 (1 cement : 4 fine sand) |
| 122 | 15 mm cement plaster on the rough side of single or half brick wall of mix:Cement mortar 1:4 (1 cement : 4 fine sand) |
| 123 | 6 mm cement plaster of mix :Cement mortar 1:4 (1 cement : 4 fine sand) |
| 124 | Neat cement punning. |
| 125 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 126 | Distempering with 1st quality acrylic distemper (readymixed) having VOC content less than 50 grams/ litre, ofapproved brand and manufacture to give an even shade[Payment shall be made after submission of TestCertificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 127 | Finishing walls with textured exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 3.28 litre/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm |
| 128 | Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface complete.Water thinnable cement primer |
| 129 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 130 | Wall painting with acrylic plastic emulsion paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : Two or more coats on new work |
| 131 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 132 | Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, 1800mm length (minimum) and 100 mm wide (minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of local teak wood of size 20x15 mm in centre of each tile and bottom and top of work height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded poly ethylene foam of density 40kg/cum in two layers, first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bomboo wood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, etc. all complete as per direction of Engineer-in-charge. |
| 133 | Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated rainscreen tiles of height 250/ 300/ 400 mm and length of 595 mm of approved texture,design and pattern having Flexural Strength/ Modulus of Rupture of ≥ 14 N/m² and maximum water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical ‘T’ (for intermediates) / ‘L’(for ends/ termination)/ Tubular sections (at corners)of size 80x60x2 mm/ 40x60x2 mm / 40x40x2 mm respectively, spaced at maximum spacing of 600 mm c/c matching to the tile vertical grid, and horizontal aluminium ‘C’-clamps of size 56x25x2 mm thickness of length 150 mm at junction of tiles and of length 75 mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/ 300/ 400 mm c/c matching to the tile horizontal grid with two numbers of self-drilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers. The vertical ‘T’/’L/ Tubular’ sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80 microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12 mm at outer corners and stainless steel grade 304,M10 full threaded anchor fasteners with nylon sleeve 100 mm long (for brick work) and M8 expansion anchor fasteners 75 mm long for concrete surface, spacing of brackets to be based on a structural/ static calculation. The brackets shall be of length 175 mm at junction of two vertical aluminium profiles and of length 100 mm at intermediate points of vertical profiles and shall be fixed to the vertical aluminium T / L / Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size 5.5x25 mm with EPDM washers. EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shall be mounted on the ‘C’ clamps such that the tiles are supported at top and bottom at both ends. The tiles shall be additionally secured to the horizontal ‘C’ clamps using special SS clips of required size which shall be inserted and pressed into position on the ‘C’ clamps holding the tiles and the cut-tiles shall be glued at points to the horizontal ‘C’ clamps by using MS Polymer sealant adhesive. The vertical joint open groove between two adjacent tiles shall be 5 mm. The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones. The tiles shall be installed using the ventilated rain screen principle with provision for natural ventilation of the space between the façade tiles and the structural wall. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge. Note : Scaffolding wherever required to be paid separatelyWith 16 mm thickness (+/- 10%) terracotta tiles of grey colour |
| 134 | 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement motar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone.Red sand stone |
| 135 | Providing and fixing stone slab with table rubbed, edges rounded and polished of size 75x50 cm deep and approved thickness fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-incharge and finished smooth including rubbing, curing etc. complete at all levels as required (measurement should be of exposed finished work):-White Agaria Marble Stone of approved shade of 18mm thick (75 x 50 cm). |
| 136 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with :Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 137 | Bill No. XI: Dismantling & Demolishing |
| 138 | Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge:-Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 139 | Nominal concrete 1:4:8 or richer mix (i/c equivalent design mix) |
| 140 | Demolishing reinforced cement concrete manually / by mechanical means including stacking of steel bars properly and disposal of unserviceable material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge. |
| 141 | Extra for cutting reinforcement in RCC or R.B. work manually / by mechanical means (payment to made on the cross sectional area of RCC or R.B. work) etc. complete as per direction of the Engineer- in-charge. |
| 142 | Extra for scrapping, cleaning and straightening reinforcement obtained from RCC or R.B. work etc. complete as per direction of the Engineer- in-charge. |
| 143 | Demolishing brick work including stacking of serviceable materials and disposal of unserviceable materials with all lifts and upto a lead of 50m etc. complete as per direction of the Engineer- in-charge:-In cement mortar |
| 144 | Removing mortar from brick and cleaning bricks including stacking bricks and disposal rubbish with all lifts and upto a lead of 50 m etc. complete as per direction of the Engineer- in-charge:-In cement mortar |
| 145 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sqm and below |
| 146 | Of area beyond 3 sqm |
| 147 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For Thickness of tiles 10 mm to 25 mm |
| 148 | Dismantling and stacking within 50 metres lead, fencing posts or struts including all earth work and dismantling of concrete etc. in base of:T or L iron pipe |
| 149 | Dismantling steel work in built up section in channels, angles, tees, flats including all gusset plates, bolts, nuts, cutting rivets, welding including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50 m etc. complete as per direction of the Engineer- in-charge. |
| 150 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 151 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 152 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge. |
| 153 | Bill No. XII: Swimming Pool |
| 154 | Supply, Installation, Testing and Commissioning of following Mechanical, Electrical and Plumbing Equipments and other miscellaneous items for Swimming PoolFilters:Bobbin Wound Horizontal filter,1200mm diameter. Filtration velocity 30m³/hr/m². Max. working pressure : 2.5 kg/cm². Flow rate : 59m³/hr. Outlet: 140mm. Filter Length-1900mm, a) Maximum operatin temperature 50 degree centigrade.b) Comply with European standards for pressure vessels 97/23/CE included in section 3 of article 3. c) Hydraulic pressure test 1.50 times the maximum admissible pressure.d) Resistance and thickness calculations are basd on norms BS-4994 and AD merkblatt N1.e) characterisctics of internal components as follows: - i) internal components and pipe in PVC. ii) PP laterls with 0.30 Slots. iii) Bolts, nuts and washers is AISI-316 iv) EPDM seals and gaskets complete all as specified and Filters are designated official products of FINA with certificate |
| 155 | Active Clear Glass Media• More efficient and environmentally friendly filtration.• Greater filtration capacity.• Water and energy savings.• Cleaner filter bed as bacteria does not remain trapped and fewer chemical products are needed |
| 156 | Valve BatterySupply, Installation, Testing & Commissioning of Valve Battery Manifold made in PVC with flanges for connecting to filters as per DIN 2501 standards. Consists of set of 5 - buttterfly valves for carrying out filtration, back-washing, rinsing and shut down of the filters .etc., complete . Size : 140mm. DIN-2501 standard. |
| 157 | Valve Battery Supports:Supply, Installation, Testing & Commissioning of Valve battery supports made in Zinc Plated Steel ..etc., complete , Height : 2.30m |
| 158 | Support Brackets 2 Support Brackets with anti-vortex clamps and fixing screws |
| 159 | Re-circulating Pumps Supply, Installation, Testing & Commissioning of Cast Iron Pumps 3000 r.p.m. Mechanical Seal in Stainless Steel. I.P.-54 motor protection. Stainless steel AISI-420 shaft with stainless steel AISI-316 strainer basket. Conn. PN-16 according to DIN2501. Flowrate : 60m3/h @ 12m.head. 5.5 HP Voltage 400V/ 3 ph.etc., complete. (1 working and 1 standby). |
| 160 | Membrane Dosing Pumps: Electronic dosing pump to be mounted both on its base as well as hung on the wall. Pumps following CE regulations, IP- 65 protection. Power connections : 220/240V, 50/60 Hz. The materials in contact with liquid are : Ploypropylene,Viton, Teflon and PVC. Includes anti-acid plastic case. Operating panel protection provided by a transparent polycarbonate cover. Lubrication not required. Flow 20L/hr @ 5 bar |
| 161 | Chemical Storage Tanks: Supply, Installation, Testing & Commissioning of Semi transparent polyethelene tank with external scale so that levels can be checked easily, capacity of tank 500lts .etc., complete |
| 162 | Supply, Installation, Testing & Commissioning of Agitators for easy installation in the tanks, provided with steering grip in bakelite, rod and propellor arms in PVC .. length of stirring rod 900mm. etc., complete |
| 163 | Agitators: Supply, Installation, Testing & Commissioning of Agitators for easy installation in the tanks, provided with steering grip in bakelite, rod and propellor arms in PVC .. length of stirring rod 900mm. etc., complete |
| 164 | UV system with minimum 60 m3/h with onfiguration, low pressure UV lamps powered by magnestic ballast housed within a separate wall mounted panel. The lamp power shall be adjusted from the control panel and when the pool is not in use the lamp output shall be set to low. The UV reactor incorporates a automatic wiper system which shall allow cleaning of the internal thimble housing the UV lamp. The reactor vessel shall be in SS 316 L and flanges shall conform to BS 4504, lamp shall be made of high purity quartz. The wiper ring shall be spring loaded PTFE. The system shall also incorporate lamp replacement indicator and lamp failure alarm. As an option the system shall also incorporate UV intensity meter. |
| 165 | Pool Drains : Supply, Installation, Testing & Commissioning of Drain grille. Stainless steels grille with screws, 500 mm x 500 mm in AISI 304.EN 13451 Standard Max. recommended flow 43 m3/h (0,5 m/s).etc., complete. |
| 166 | Suction Inlet |
| 167 | PVC wall conduits: Supply, Installation, Testing & Commissioning of PVC wall conduits 300mm long. Rear connection to pipe by 2\\" .etc., complete |
| 168 | Inlets: Supply, Installation, Testing & Commissioning of White ABS plastic bottom inlet for concrete with S.S. screws and regulable .Flow/ inlet = 9,000 l/hr. EN-13451-1 Standard.etc., complete |
| 169 | Overflow Gutter Drains: Supply, Installation, Testing & Commissioning of drain fitting with body grille in ABS |
| 170 | Ladders: Supply, Installation, Testing & Commissioning of Ladder of width 500 mm with Ø 43 handrails in hand polished AISI-316 stainless steel. Complete with fixing anchors and earth connection. With added top double safety step and increased overall height in accordance with EN 13451-2Standard. Includes non-slip LUXE steps in AISI-316 stainless steel. 3 Steps. etc., Complete. |
| 171 | Underwater Lights: Supply, Installation, Testing & Commissioning of Led 36W light with Niche and ABS/SS 316 Faceplate |
| 172 | Underwater Lights: Supply, Installation, Testing & Commissioning of Led 18W light with Niche and ABS/SS 316 Faceplate |
| 173 | Junction Boxes: Supply, Installation, Testing & Commissioning of Junction Boxes, made in ABS, composed of 3 entries 3/4\\" .UNE 20324 : 1993 +1a MOD:2000(EQV a EN 60529:1991 + ERRATUM + A1:2000)+ERRATUM:2004.etc., complete |
| 174 | Flexible Cable Conduits: Supply, Installation, Testing & Commissioning of Cable Conduit Hose, Flexible 1 mt. long conduit for connecting light to junction box. 3/4\\" .etc., complete. |
| 175 | Transformers/power supply for light: Transformers with IP 64 protection, 300VA from 220V to 12V |
| 176 | Supply, Installation, Testing and Commissioning of Ball Valve of dia 63 mm |
| 177 | Supply, Installation, Testing and Commissioning of Butterfly Valve Dia of 90 mm |
| 178 | Supply, Installation, Testing and Commissioning of Flange and Adaptor for 90 mm dia Butterfly Valve. |
| 179 | Supply, Installation, Testing and Commissioning of Butterfly Valve of Dia 110 mm |
| 180 | Supply, Installation, Testing and Commissioning of Flange and Adaptor for 110 mm dia Butterfly Valve. . |
| 181 | Supply, Installation, Testing and Commissioning of Butterfly Valve Dia 160 mm |
| 182 | Supply, Installation, Testing and Commissioning of Flange and Adaptor for 160 mm dia Butterfly Valve. |
| 183 | Supply, Installation, Testing and Commissioning of Wafer Check Valve of Dia 90 mm |
| 184 | Supply, Installation, Testing and Commissioning of Wafer Check Valve of Dia 160 mm |
| 185 | Supply, Installation, Testing & Commissioning of Metallic vaccum head in polished Al and chrome bronze - 1.5\\" length 442mm. |
| 186 | Supply, Installation, Testing & Commissioning of Extensible handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf, skimmers and scoops.10.0mts. Long with Handle adaptor . |
| 187 | Supply, Installation, Testing & Commissioning of Transparent blue plastic vacuum hose 11/2\\" dia 30mtrs long including hose cuffs for connection to suction inlets .etc., complete. |
| 188 | Supply, Installation, Testing & Commissioning of Deep bag net made in polypropelene and white polyester netting, Shark Series.etc., complete |
| 189 | Supply, Installation, Testing & Commissioning of Surface net made in polypropelene and white |
| 190 | Supply, Installation, Testing & Commissioning of Curved brushes made in polypropelene for pool |
| 191 | Supply, Installation, Testing & Commissioning of Straight brushes made in polypropelene for pool . |
| 192 | Supply, Installation, Testing & Commissioning of Algae brushes with stainless steel bristles .etc., complete |
| 193 | Supply of Test kit for free chlorine & pH |
| 194 | Supply of Chlorine Testing Tablets - 250 nos. in a pack |
| 195 | Supply of Phenol (pH) reagent-250 Tablets |
| 196 | Supply of pH increasing chemical compound for swimming pool |
| 197 | Supply of pH decreasing chemical compound for swimming pool |
| 198 | Supply of Algaecide |
| 199 | Supply of TCCA Granules |
| 200 | Supply, Installation, Testing & Commissioning of 63 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard |
| 201 | Supply, Installation, Testing & Commissioning of 90 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard |
| 202 | Supply, Installation, Testing & Commissioning of 110 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard |
| 203 | Supply, Installation, Testing & Commissioning of 140 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard |
| 204 | Supply, Installation, Testing & Commissioning of 160 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard |
| 205 | Supply, Installation, Testing & Commissioning of 4x2.5 mm2 Copper cable for under water light from Junction box to Electrical panel of U/W Light, complete with Conduit. |
| 206 | Supply, Installation, Testing & Commissioning of 3x4 mm2 Copper cable for under water light from Junction box to Electrical panel of U/W Light, complete with Conduit. |
| 207 | Supply,Installation, Testing & Commisioning of control panel for Centrifugal Pump 5.5HP (Filtration-1W+1S) -2 No's, 2. Dosing Pump-2. 300W Transfomer-4No's,. complete as required, MCC panel as described, complete: Contactors,Push Button & Indicators,Selector Switch, Ammeter,Volt Meter, Lugs, Wires, Enclosure. |
| 208 | Bill No. XIII: Landscape |
| 209 | Dismantling of Brick/Tile Work as per MoRD Technical Specification No. 202 Dismantling of existing structures like culverts, bridges, retaining walls and other structures comprising of brick masonry icluding disposal of unserviceable material and stacking the serviceable material with all lift upto a lead of 1000 m as per MoRD Technical Specification clause 202.D) Dry Brick Pitching or Brick Soling |
| 210 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed: -All kinds of soil |
| 211 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 212 | Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8. |
| 213 | Granular sub-base with Well Graded Material (Table 400.1) using Jhama Brick Aggregate(A) By Mix in Place MethodConstruction of granular Sub-base by providing well graded material (Jhama Brick aggregates) spreading in uniform layers with motor grader on prepared surface, mixing by mix in place metjod with rotovator at OMC, and compacting with smooth wheel rollr to achieve the desired densitty, complete as per MoRD Technical Specification Clause 401.(i) For Grading-I Material |
| 214 | 18 mm thick Polished Jhansi Red Granite flooring iin pathways and foothpaths |
| 215 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All Work upto Plinth Level1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size) |
| 216 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All Work upto Plinth Level1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 217 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 218 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 219 | Gravel / Soil - Aggregate Surface Course ( Table 400.3 )Construction of gravel / soil - aggregate surface course by providing well graded material, spreading in uniform layers with Tractor mount grader on prepared surface, mixing by mix in place method with Tractor mount rotavator at OMC, and compacting with three wheel 80 - 100 kN static roller to achieve the desired density, complete as per Technical Specification Clause 402. |
| 220 | Providing and laying at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1 : 3 ( 1 cement : 3 fine sand) including the cost of required centering, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 ( 1 cement : 3 fine sand) on exposed surface complete.1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 221 | 80 mm thick factory made c.c interlocking paver block of M-35 GradeProviding and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge:(a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. Cement concrete 1:2:4 in pavements, laid to required slope and camber in panels |
| 222 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 223 | Providing weep holes on brick masonry/ plain/ reinforced concrete wall with 90 mm dia uPVC pipe with ISI mark of approved/ reputed make extending through the full width of the structures with slope of 1(V):20(H) towards drawing face including cutting, fixing etc. complete as per drawing and direction of the Engineer-in-Charge and technical specification. |
| 224 | Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge. |
| 225 | Centering, Shuttering including struttings, propping etc and removal of form work for:Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply |
| 226 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. |
| 227 | Finishing walls with water proofing cement paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 3.84 kg/10 sqm) |
| 228 | Providing and fixing as per drawing /image STAINLESS STEEL DUSTBIN SERIES : Wheel dustbin capacity 1100 ltr 4 wheels with lid 1360x1060x1370 HDPE |
| 229 | Providing and fixing stainless steel ( Grade 304) Sign board / Benches, chair, Scultures, canoppy made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing tubes, channels, plates etc., including welding, grinding, and making curvature (wherever required) and fitting the same withbuffing, polishing necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.-Making the Sign board on S steel sheet |
| 230 | Supply and Installation of HDPE Docks/Folating jeety size 666mmx666mmx400mm with hand rails |
| 231 | Bill No. XIV: Horticulture |
| 232 | Fine dressing the ground |
| 233 | Mixing earth and sludge or farm. yard manure in proportion specified or as directed. |
| 234 | Spreading of Sludge / Farm Yard Manure / good EarthSpreading of sludge/ farm yard manure/ good earth in required thickness (cost of sludge, farm yard manure or/and good earth to be paid for separately) MoRT&H technical specifications Clauses 307. |
| 235 | Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm Thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and then rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of Officer-in-charge |
| 236 | Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same, as per direction of Officer-in-charge. |
| 237 | Mixing earth and sludge or faRmt. yard manure in proportion specified or as directed. |
| 238 | Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farm-yard manure (cost of well decayed farm yard manure to be paid separately) in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and liftsHoles 1.2 m dia and 1.2 m deep. |
| 239 | Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farm-yard manure (cost of well decayed farm yard manure to be paid separately) in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and liftsHoles 60 cm dia, and 60 cm deep. |
| 240 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration (5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Syzygium cumini (Jambhun), Minimum 3.0/3.5m overall height, Minimum 50mm caliper, Multibranching at 2.0m from collar |
| 241 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Butea monosperma (palash), Minimum 3.0/3.5m overall height, Minimum 60mm caliper, Multibranching at 2.0m from collar |
| 242 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Ficus infectoria (Payari), Minimum 3.0/3.5m overall height, Minimum 60mm caliper, Multibranching at 2.0m from collar |
| 243 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Aegle marmelos (Beal), Minimum 3.0/3.5m overall height, Minimum 40mm caliper, Multibranching at 2.5m from collar |
| 244 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Terminalia arjuna (Arjun), Minimum 3.5m overall height, Minimum 60mm caliper, Multibranding at 2.00m |
| 245 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Mimusops elengi (Bakul)Champa, Minimum 3.0/3.5m overall height, Minimum 75mm caliper, Multibranching at 1.5m from collar |
| 246 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Shorea robusta (Sal), Minimum 3.0/3.5m overall height, Minimum 60mm caliper, Multibranching at 2.0m from collar |
| 247 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Anthocephalus cadamba (kadamba), Minimum 3.0/3.5m overall height, Minimum 75mm caliper, Multibranching at 1.5m from collar |
| 248 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Mangifera indica(Mango), Minimum 3.0/3.5m overall height, Minimum 60mm caliper, Multibranching at 2.0m from collar. |
| 249 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Azardita indica (Neem), Minimum 3.0/3.5m overall height, Minimum 60mm caliper, Multibranching at 2.0m from collar |
| 250 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ERYTHRINA INDICA, Minimum 3.0/3.5m overall height, Multibranching at 2.5m from collar, min. 60m Caliper. |
| 251 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-GARDENIA LATIFOLIA,CAPE JASMINE, Multibranching at 2.0m from collarMinimum 2.0/2.5m overall height, |
| 252 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-JACARANDA MIMOSIFOLIA, NEELA GULMOHAR, Minimum 3.0/3.5m overall height, Minimum 60mm caliper, Multibranching at 2.0m from collar. |
| 253 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-LAGERSTOEMIA THORELLII, Minimum 3.0/3.5m overall height, Minimum 60mm caliper, Multibranching at 2.0m from collar. |
| 254 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-MALALEUCA LEUCADENDRON, GOLDEN BOTTLE BRUSH, Minimum 2.0/2.5m overall height, Minimum 40mm caliper, Multibranching at 2.0m from collar. |
| 255 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-PLUMERIA ALBA, FRANGIPANI,Minimum 3.0/3.5m overall height, Minimum 75mm caliper, Multibranching (4-5) branches at 1.5m from collar. |
| 256 | Supply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-PLUMERIA RUBRA, RED Champa, Minimum 3.0/3.5m overall height, Minimum 75mm caliper, Multibranching (4-5) branches at 1.5m from collar. |
| 257 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting ALSTONIA SCHOLARIS Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 258 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting BAUHINIA BLACKEANA (KACHNAR), Minimum 3.5/4.0m overall height, Minimum 55-60mm caliper, Multibranching at 2.0m from collar |
| 259 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting BAUHINIA PURPUREA (KACHNAR PURPLE) Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 260 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting BAUHINIA VAREGATA (KACHNAR WHITE) Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 261 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting BOMBAX MALABARICUM (SAVAR) Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 262 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting CALISTEMON LANCEOLATUS (BOTTLE BRUSH) Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 263 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting CASSIA FISTULA (AMALTAS) Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 264 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting CASSIA JAVANICA (PINK CASSIA) Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 265 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting CORDIA SEBESTINA (SCARLET CORDIA) Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 266 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting DELONIX REGIA (GULMOHAR ) Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 267 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting LAGERSTROEMIA FLOS REGINAEMinimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 268 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting MELIA AZEDARACH Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 269 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting NYCANTHES ARBORTRISTIS Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 270 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting PELTOFORUM FERRUGILUM Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 271 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting SCHLEICHERA OLEOSA Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 272 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting TABEBUIA ARGENTEA Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 273 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting ANOGEISSUS PENDULA Minimum 3.5/4.0m overall height, Minimum 60mm caliper, Multibranching at 2.5m from collar |
| 274 | PALMSSupply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting ARECA PALM-SUPARI,Minimum 5 canes per palm |
| 275 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting ROYESTINIA REGIA, Minimum 3.5m overall height, Minimum 100mm caliper,5 fronds. |
| 276 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting FOX TAIL PALM, Minimum 3.5m overall height, Minimum 100mm caliper, 5 fronds. |
| 277 | SHRUBSSupply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ACALYPHA HISIPIDA CAT TAIL, Minimum 600mm height@900mmc/c, Bushy, Multibranching, Flowering. |
| 278 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ACALYPHA W GREEN, Minimum 600mm height@750mmc/c, Bushy, Multibranching. |
| 279 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ACALYPHA W RED, Minimum 600mm height@750mmc/c, Bushy, Multibranching |
| 280 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ACALYPHA TRICOLUR, Minimum 600mm height@750mmc/c, Bushy, Multibranching |
| 281 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ALLAMANDA NERIFOLIA, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 282 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CAESALPINIA PULCHERRIMA, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 283 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CALLIANDRA EMARGINATA, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 284 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CALLIANDRA HAEMATOCEPHALLA, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering. |
| 285 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CASSIA BIFLORA, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 286 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CALLIANDRA BREVIPES, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering. |
| 287 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-LAGERSTROEMEA INDICA (Species Muve, white, Pink Red) CANDIDA, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 288 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Nerium oleander 'Petite Pink' Dwarf Pink , Minimum 900mm height@750mmc/c, Bushy, Multibranching, Flowering |
| 289 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CESTRUM ELEGANS, Minimum 600mm height@600mmc/c, Bushy, Multibranching, Flowering |
| 290 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HAMELIA PATTENS, Minimum 1500mm height@900mmc/c, Bushy, Multibranching |
| 291 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HIBISCUS ROSA PROLIFIC, Minimum 600mm height@600mmc/c, Bushy, Multibranching |
| 292 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HIBISCUS DAFFODIL YELLOW, Minimum 600mm height@600mmc/c, Bushy, Multibranching, Flowering |
| 293 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HIBISCUS ROSA SINENSIS ( RED SATIN), Minimum 600mm height@600mmc/c, Bushy, Multibranching, Flowering |
| 294 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-IXORA CHENENSIS, Minimum 600mm height@600mmc/c, Bushy, Multibranching, Flowering |
| 295 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-JASMINUM HUMILE, Minimum 900mm height@600mmc/c, Bushy, Multibranching, Flowering |
| 296 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-NERIUM OLEANDER Variegatum Plenum, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 297 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-TABERNAEMONTANA CORONERIA, Minimum 600mm height@600mmc/c, Bushy, Multibranching, Flowering |
| 298 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-TABERNAEMONTANA CORONERIA VARIEGATED, Minimum 600mm height@600mmc/c, Bushy, Multibranching, Flowering |
| 299 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-GARDENIA JASMINOIDES, Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 300 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HIBISCUS COOPERII, Minimum 600mm height@750mmc/c, Bushy, Multibranching, Flowering |
| 301 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-IXORA CHENENSIS, Minimum 600mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 302 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-JATROPHA PAUNDARAEFOLIA, Minimum 600mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 303 | Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-TECOMARIA CAPENSIS, Minimum 600mm height@900mmc/c, Bushy, Multibranching, Flowering |
| 304 | COURTYARD PLANTSSupply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-RAPHIS PALM, Minimum 600mm height @300mmc/c, 3 /4fronds |
| 305 | CLIMBERSSupply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ANTIGNON LEPTOPUS, Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant |
| 306 | Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-BEAUMONTIA GRANDIFLORA, Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant |
| 307 | Supply & Install Climbers inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-BOUGAINVELLEA spp. Mix, Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant |
| 308 | Supply & Install Climbers inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CLERODENDRON SPLENDENS , Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant |
| 309 | Supply & Install Climbers inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-IPOMEA CURELEA, Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant |
| 310 | Supply & Install Climbers inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-IPOMEA PURPUREA, Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant |
| 311 | Supply & Install Climbers inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-JASMINUM NITIDUM, Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant |
| 312 | Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-QUISQUALIS INDICA, Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant. |
| 313 | Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-THUNBERGIA ALATAMinimum 600mm height @2000mmc/c, Minimum 3 runners per plant. |
| 314 | Supply & Install Climbers inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-VERNONIA ELAEAGNIFOLIA, Minimum 600mm height @2000mmc/c, Minimum 3 runners per plant. |
| 315 | GROUND COVERSMixing earth and sludge or faRmt. yard manure in proportion specified or as directed. |
| 316 | Supply & Install gound covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ALTERNENTHERA RED, Minimum 150mm height @200mmc/c, Bushy. |
| 317 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CHLOROPHYTUM COSMOSUM, Minimum 150mm height @200mmc/c, Minimum 3 runners per plant. |
| 318 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-IRESINE, Minimum 150mm height @200mmc/c, Minimum 3 runners per plant. |
| 319 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-IPOMEA GOLDEANA, Minimum 300mm height @200mmc/c, Minimum 3 runners per plant. |
| 320 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-OPHIOPOGON BLACK GRASS. |
| 321 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-SYNGONIUM MACROPHYLLUM, Minimum 150mm height @200mmc/c, Minimum 3 runners per plant. |
| 322 | Supply &Install ground covers/ Shade plants inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-WEDELIA TRILOBATA, Minimum 3 runners per plant, Minimum 150mm height @200mmc/c. |
| 323 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ZEBRINA PENDULA, Minimum 300mm height @250mmc/c, Minimum 3 runners per plant. |
| 324 | HEDGESSupply & Install plants to form hedge , inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-MURRAYA EXOTICA, Minimum 300mm height @300mmc/c, Bushy |
| 325 | Supply & Install plants to form hedge inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CLERODENRON MACROSIPHON, Minimum 350mm height @200mmc/c, Bushy |
| 326 | Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-DURANTA GOLDEN PLUMERI Minimum 300mm height @200mmc/c, Bushy |
| 327 | Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CLERODENDRON INERME, Minimum 300 mm height @200mmc/c, Bushy |
| 328 | Supply & Install plants to form hedge, inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.LOROPETALUM CHINENSIS Minimum 450mm height @450mmc/c, Bushy |
| 329 | Supply & Install plants to form hedge, inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-MURRAYA PANICULATA Minimum 300 mm height @300mmc/c, Bushy |
| 330 | Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as requirediii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-FICUS LONGISLAND Minimum 150mm height @200mmc/c, Bushy |
| 331 | Supplying at site of work well-decayed farm.-yard manure, from any available source, approved by the Engineer-in-charge including screening and stacking. |
| 332 | Supplying site of work-Deoiled Neem-Cake duly packed in used bags |
| 333 | Supplying at site of work sludge duly stacked at site. |
| 334 | BAMBOOSupply & Install Trees/ Palms inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where requirediv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Dendrocalamus Strictus(Velu),Minimum 3.0/3.5m overall height, 60MM CALIPER, Multibranching at 2.5m from collar |
| 335 | Supply & Install Grasses inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting. Bambusa Vulgaris (GOLDEN BAMBOO), Minimum 2400mm height, (4-5) Stems in one clump |
| 336 | Supply & Install Grasses inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting. Dendrocalamus Asper (ROUGH GIANT BAMBOO), Minimum 2.5m height, 150 Dia |
| 337 | Supply & Install Grasses inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting. ,Bambusa Wamin (Buddha Belly Bamboo), Minimum 1.8 m height, Clumps of 2/3 Stems. |
| 338 | Supply & Install Grasses inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting. ,Cymbopogon Citratus (Lemon Grass), Minimum 600mm height, Clumps of 20/25 Grass Shoots. |
| 339 | Bill No. XV: Sanitation & Plumbing |
| 340 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.15 mm nominal outer dia .Pipes. |
| 341 | 20 mm nominal outer dia .Pipes. |
| 342 | 32 mm nominal outer dia .Pipes. |
| 343 | Providing and fixing Chlorinated PolyvinylChloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain &brass threaded fittings This includes jointing of pipes& fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints complete asper direction of Engineer in Charge. - External work32 mm nominal outer dia .Pipes. |
| 344 | 50 mm nominal outer dia .Pipes. |
| 345 | Providing and fixing on wall face unplasticised RigidPVC rain water, soil, waste & vent pipes (workingpressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion:Single socketed pipe - 75 mm OD |
| 346 | Single socketed pipe - 110 mm OD |
| 347 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: - Coupler75 mm |
| 348 | 110 mm |
| 349 | Single equal tee with door - 75x75x75 mm |
| 350 | 110x110x110mm |
| 351 | Bend 87.5° - 75 mm |
| 352 | 110mm |
| 353 | Single unequal junction of required degree with door - 110x110x75 mm |
| 354 | Providing and fixing unplasticised -PVC pipe clips ofapproved design to unplasticised - PVC rain water,soil, waste & vent pipes by means of 50x50x50mmhard wood plugs, screwed with M.S. screws ofrequired length including cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. - 75 mm |
| 355 | 110mm |
| 356 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 357 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid. |
| 358 | Providing and Fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. Automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required : Single squatting plate with 5 litre P.V.C. automatic flushing cistern. |
| 359 | Range of two squatting plates with 5 litre P.V.C. automatic flushing cistern. |
| 360 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineerin- Charge. |
| 361 | Providing and Fixing white vitreous china flat backhalf stall urinal of size 580x380x350mm with whitePVC automatic flushing cistern, with fittings,standard size C.P. brass flush pipe, spreaders withunions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. |
| 362 | Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern. |
| 363 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps,32 mm C.P. brass waste ofstandard pattern, including painting of fittings andbrackets, cutting and making good the wallswherever require :White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 364 | White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps. |
| 365 | Providing and fixing white vitreous china pedestal forwash basin completely recessed at the back for thereception of pipes and fittings. |
| 366 | Providing and fixing Stainless Steel AISI 304 (18/8)kitchen sink as per IS 13983 with C.I. brackets andstainless steel plug 40 mm including painting of fittingsand brackets, cutting and making good the walls wherever required: - Kitchen sink with drain board510x1040 mm bowl depth 250mm. |
| 367 | Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white |
| 368 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 369 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe - 32 mm dia |
| 370 | 40 mm dia |
| 371 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 372 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia |
| 373 | Rectangular shape 453x357mm |
| 374 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 375 | Providing and fixing toilet paper holder : C.P Brass |
| 376 | Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38mm single piece moulded with height of270mm, effective length of tail pipe 260mm from thecentre of the waste coupling 77mm breadth with 25mmminimum water seal, weighing not less than 263gms. |
| 377 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms. |
| 378 | Providing and fixing PTMT towel rail complete withbrackets fixed to wooden cleats with CP brass screwswith concealed fitting arrangement of approved qualityand colour- 600mm long towel rail with total length of 645mm, width78mm and effective height of 88mm, weighing not lessthan 190gms. |
| 379 | Providing and fixing brass bib cock of approved quality : 15 mm nominal bore |
| 380 | 20 mm nominal bore |
| 381 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore |
| 382 | 20 mm nominal bore |
| 383 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore |
| 384 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore |
| 385 | 32 mm nominal bore |
| 386 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : 20 mm nominal bore |
| 387 | 25 mm nominal bore |
| 388 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever equired) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 389 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150 mm diameter |
| 390 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 - 15 mm nominal bore |
| 391 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 392 | EXTERNAL PLUMBINGEarth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 393 | REINFORCED CEMENT CONCRETE WORKReinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Mild steel and Medium Tensile steel bars. |
| 394 | WATER SUPPLYProviding and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329150 mm dia Ductile Iron Class K-7 pipes |
| 395 | Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K 9 conforming to IS : 8329 :100 mm dia Ductile Iron Double Flanged |
| 396 | 150 mm dia Ductile Iron Double Flanged |
| 397 | Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) - 100 mm diameter Class II |
| 398 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately): 100 mm dia |
| 399 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.75 mm nominal inner dia .Pipes. |
| 400 | Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 finesand) for sluice valve, with C.I. surface box 100mm.top diameter, 160 mm bottom diameter and 190mm deep ( inside) with chained lid and RCC topslab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) necessary excavation foundation concrete 1:5:10 (1 cement : 5fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1cement : 3 coarse sand) 12 mm thick finished with afloating coat of neat cement complete as perstandard design : With Second Class bricks |
| 401 | Providing, installation and commissioning of package type Iron Removal Plant comprising of Iron Removal Filter of dual media filter with anthracite coal, filter gravel, polypropelene double hexagonal nut strainer etc., mixing chamber for coagulants like sodium alluminates etc., oxidation chamber with manganese dioxide , metering pump for coagulant dosing, air compressor of suitable capacity with motor, back washing arrangements, disinfection with sodium hypochlorite solution through metering pump, all necessary pipes for raw water collection, inter connecting all the chambers, delivery outlet of 150 mm dia alongwith all related civil, mechanical and Electrical works etc. complete as per approved drawing, process flow, technical specification and direction of the Engineer - in - charge.2500 G.P.H CAPACITY |
| 402 | Charges for drilling and boring of pilot hole in any soil strata bywater jet or any suitable method including collection ofsamples at various suitable levels and preservation ofsamples in polythene bags / sample boxes and disposal ofexcess soil or mud and maintain the pilot hole properly andrequired staging as per specification ( IS : 2800 ) and directionof the Engineer-in-charge.100 mm dia |
| 403 | Reaming of pilot hole to an enlarged bore hole in any soilstrata by manual means, disposal of excess soil or mud,including the cost for water etc. as required to maintain thebore hole properly as per specification and direction of theEngineer - in - charge.from 100 mm dia pilot hole to 250 mm bore hole |
| 404 | Providing & lowering of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer - in - charge. 'CM' Casing pipe - 150 mm dia |
| 405 | 125 mm dia |
| 406 | RS Pipe - 100 mm dia |
| 407 | Washing & development of Tube Well by using hand pump or by any suitable method & testing of the well as per specification & direction of the Engineer in charge |
| 408 | Providing and fixing of UPVC end cap suitable for UPVC ‘CM’ casing or ‘CS’ casing or ‘RS’ pipes as per specification and direction of the Engineer-in-charge.100mm dia. |
| 409 | Providing and fixing of UPVC reducer suitable for UPVC ‘CM’ casing or ‘CS’ casing or ‘RS’ pipes as per specification and direction of the Engineer-in-charge.150 x 100 mm dia |
| 410 | Providing and fixing of housing clamp ( made with 12 mm thick MS sheet ) along with well cap (made with 10 mm thick MS sheet ) with necessary arrangements for SBDTW as per specification and direction of the Engineer - in - charge.150 mm dia |
| 411 | Providing and shrouding of the deep tube well assembly with washed pea gravels ( 2.0 - 4.75 mm effective size ) as per specification ( IS : 4097) and direction of the Engineer - in - charge.with contractor's rigwith pea gravels obtained from Durgapur, West Bengal. |
| 412 | Providing and Installation of 3 HP (single/three phase) submerssible Pump (Electrical) as per relevent IS code with LT control panels connected with 100 mtr insulated cables from the distribution lines, 2 nos. electric pole of 8.5 mtr long 7/16 cable, well cap, housing clamp, column pipes, single/three phase earthing, motor starter, control panel box with locking arrangement with all accessories complete as per the direction fo the Engineer-in-charge.For Borewell |
| 413 | Providing and Installation of 1 HP Domestic mono block pump |
| 414 | SEWAGE AND DRAINAGEProviding, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete.150 mm diameter |
| 415 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : |
| 416 | Constructing soak pit 1.20 x 1.20 x 1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 417 | Supplying and fixing C.I. cover without frame for manholes500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg. |
| 418 | Supply,Installation, Testing and Commissioning of Underground Fully Advanced Automatic Sewage Treatment Plant of Capacity of 20 KLD including solar packeg to run the plant on solar energy. |
| 419 | SOLID WASTE COMPOSTING PLANTSupply, Installation and Commissioning of Fully Automatic Electro-mechanically operated Organic Waste Composting machine handeling Maximum intake capacity 50kg/day.with Shredder 3HP (Dual Shaft).12-month warranty from the date of supply for parts against manufacturing defect. |
| 420 | Bill No. XVI: Goods |
| 421 | Supply and installation of Play EquipmentsSupply and Fixing of Swing |
| 422 | Supply and Fixing of Spring Rider Type-I |
| 423 | Supply and Fixing of Spring Rider Type-II |
| 424 | Supply and Fixing of Pyramid Net Climber |
| 425 | Supply and Providing Race Treadmill - |
| 426 | Supply and Providing Multi Gym Equipment |
| 427 | Supply and Providing Transformer+ |
| 428 | Supply and Providing Dumbells - |
| 429 | Supply and Providing Spin Bike |
| 430 | Supply and Providing Multi- Functional Trainer with smith Machine |
| 431 | Supply and Providing Leg press |
| 432 | Supply and Providing Pec deck fly |
| 433 | Supply and Providing Leg Pull down and Row |
| 434 | Supply and Providing Leg Ext and curl |
| 435 | Supply and Providing Flat simple bench |
| 436 | Supply and Providing 32mm/25mm thick GYM floor mat |
| 437 | Supply and Providing Yoga Mat |
| 438 | Supply and Providing Mirror |
| 439 | Supply and Providing Elite-Adjustable Bench |
| 440 | Supply and Providing 3 Burner Cooking Stove - |
| 441 | Supply and Providing SS Working Table Type 1 |
| 442 | Supply and Providing 3 Bowl Kitchen Sink - |
| 443 | Supply and Providing GI Hood Kitchen Exhaust with Filter - |
| 444 | Supply and Providing Gi hood Duct Line |
| 445 | Supply and Providing SS Working Table Type 2 |
| 446 | Supply and Providing 5 HP Exhaust Fan |
| 447 | Supply and Providing SS Kitchen Rack |
| 448 | Supply and Providing Double Door Cooler of 850 Litre Capacity |
| 449 | Supply and Providing Double Door Deep Freezer of 320 Litre Capacity |
| 450 | Supply and Providing Single Door 45L Mini Fridge |
| 451 | Providing and fixing in play equipment , including excavation of 0.45 x 0.45 x 0.45 m size pit and fixing the each supporting leg / anchoring arm. of playing instrument in grade concrete block of 0.45 x 0.45 x 0.45 m size including curing etc. complete including providing for epdm flooring at all fall areas (min 1.50x 1.50 m ).A-Multi activity play equipment with straight tube slide of 3' ht, small wave slide 3' ht with slide entry, an railing with abacus play system, an FRP steps to climb to a metal sq deck with canopy.-Play zone 35' x 25'-Max platform. ht 3'-Age group 3-6 yrs |
| 452 | Multi activity play equipment with 1. double wave slide of 5' ht, 2. spiral slide 5' ht with slide entry, bridge 2nos, 3. metal plain bridge 8' length with cross checked railing assembly and 4. swinging bridge with railing assembly, 5. railing with cross and zero play system, 6. an metal ladder 5' height, and 7. 3 nos metal sq deck with canopy ( 2nos) and without canopy( 1 nos) .8. crawl tube below 8' length below deck.9. metal rock climber 5' height. with hand rails at suitable positionsand a clinging bar.-Play zone 40' x 36' approx-Max platform. ht 5'-Age group 5-12 yrs |
| 453 | Providing and fixing Tri basket, Area :2.0m Dia Safe Play Area : 3.5m Dia (11.5ft Dia) Ideal For 5-14Years,Friends at a time :4-6 on suitable location at smart park |
| 454 | Providing and fixing see - saw Product Area :0.4m X 0.75m,Safe Play area:1.4m X2m,Ideal For : 3-8 YearsFriends at a time :2, on suitable location at smart park |
| 455 | Providing and fixing Standard See-saw, Product Area : 2.5m X 0.3m, Safe Play Area :3.5m X1.3m, Ideal For :4-10 Years, Friends at a time : 2 no.on suitable location at smart park |
| 456 | Providing and fixing Double Post Swing,Area : 3.5m x 1.0m,• Safe Play Area : 4.5m X 2.0m • Ideal For : 4-14 Years, Friends at a time : 2 on suitable location at smart park, |
| 457 | Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. complete. of FRP Wave Slide 1.5 Mtr having Dimension: • Product Area : 5m x 0.6m (18ft x 8.2ft) • Safe Play Area : 6.5m x 3.5m (21.3ft x 11.5ft) • Age Group : 4-12 yrs.Product details as per attached Specification. |
| 458 | Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. complete. of Delux slide 1.5 mtr having Dimension: • Product Area : 4.5m x 0.7m (14.8ft x 2.3ft) • Safe Play Area : 5.5m x 1.7m (18ft x 5.6ft)-Age Group : 4-12 yrs. Product details as per attached Specification. |
| 459 | Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. of FRP Double Roller Slide 1.5 Mtr having Dimension: • Product Area : 6.5m x 2.5m (21.3ft x 8.2ft) • Safe Play Area : 7.5m x 3.5m (24.6ft x 11.5ft) • Age Group : 4-12 yrs.- Product details as per attached Specification. |
| 460 | Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. of Multi seater see-saw having Dimension: • Product Area : 0.5m X 3m (1.6ft X 9.8ft) • Safe Play Area : 1.5m X4m (4.9ft X 13.1ft) • Ideal For : 3-10 Years • Friends at a time : 4 - Product details as per attached Specification. |
| 461 | Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. of Simply Go Round having Dimension• Product Area : 1.5m Dia ( 5 ft Dia.)• Safe Play Area : 2.5m Dia ( 8.2ft Dia.)• Ideal For : 5-12Years• Friends at a time : 5-7 . Product details as per attached Specification. |
| 462 | Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc.of PYRAMID SCRAMBLER having Dimension: • Age Group :- 6 - 12 yrs. Product Area :- 5 m x 5 m Safe Play Area :- 6 m x 6 m. Product details as per attached Specification. |
| 463 | Bharat AC001 10 KW Charger(3 Socket)Installation and Commissioning of Bharat AC001 10 KW Charger(3 Socket)One time on-boarding setup charges of Bharat AC001 10 KW Charger(3 Socket) |
| 464 | AC Level -2 Charger 7.4 KWInstallation and Commissioning of AC Level -2 Charger 7.4 KWInstallation and Commissioning of AC Level -2 Charger 7.4 KW |
| 465 | DC Fast Charger CCS-2 30 KW Single GunInstallation and Commissioning of DC Fast Charger CCS-2 30 KW Single GunOne time on-boarding setup charges of DC Fast Charger CCS-2 30 KW Single Gun |
| 466 | DC Fast Charger CCS-2 40 KW Double GunInstallation and Commissioning of DC Fast Charger CCS-2 40 KW Double GunOne time on-boarding setup charges of DC Fast Charger CCS-2 40 KW Double G |
| 467 | Bill No. XVII: Furniture |
| 468 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :Sal Wood |
| 469 | Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete.Kiln seasoned and chemically treated hollock wood |
| 470 | French spirit polishing [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new works including a coat of wood filler |
| 471 | Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked to frame, backing or studding with screws etc. complete. (Frames, backing or studding to be paid separately): - 12 mm thick |
| 472 | 18 mm thick |
| 473 | Providing and fixing aluminium tee channels (heavy duty) with rollers, stop end in pelmets as curtain rod. |
| 474 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality.1.5 mm thick |
| 475 | Providing and fixing Pre-laminated medium density fibre board conforming to IS: 14587:1998 marked, with one side decorative lamination and other side balancing lamination Grade-I(exterior grade), in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately) 25 mm thick |
| 476 | Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete. |
| 477 | Providing and fixing powder coated telescopic drawer channels 300mm long with necessary screws etc. complete as per directions of Engineer-in-charge. |
| 478 | Providing and fixing in position wall panelling at all heights with 6 mm thick BWP ply board lapping with 4 mm thick Teak Veneer of approved quality in outer face, decorative teak wood bead (50 x 40 ) at top and skirting (150 x 25), comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally ply board are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm all complete as per manufacturer's specification as per direction of Engineer-in-Charge all complete. |
| 479 | Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.200 mm |
| 480 | Providing and supplying Unbranded Wooden Chair of approved quality, design, and make, made from seasoned hardwood (such as teak / rubberwood / beech wood or equivalent), suitable for office, visitor, or general seating use, conforming to the following specifications and requirements, complete as directed by the Engineer-in-Charge. |
| 481 | Providing and supplying Star Homz Cotton Mattress, factory-made, of approved make and quality, weighing not less than 12 kilograms, conforming to the following technical specifications, complete as directed by the Engineer-in-Charge. |
| 482 | Providing and supplying STAR HOMZ Cotton Mattress weighing 12 kilograms (±5%), manufactured from high-quality long-staple cotton properly carded and layered, enclosed in a cotton / woven fabric cover of approved shade and pattern.The mattress shall be uniformly filled, well-quilted, and neatly stitched on all sides to retain shape and firmness during use.All materials used shall be clean, hygienic, and free from synthetic fibre or impurities.The mattress shall be comfortable, durable, and suitable for regular institutional / domestic use.Type: Cotton Mattress – 12 KgComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 483 | Providing and supplying Star Homz Pillow Cover, made from Khadi fabric conforming to IS:13717/1993, of approved shade and quality, size 59 cm (±0.5 cm) × 33 cm (±0.5 cm), neatly stitched and finished, complete as directed by the Engineer-in-Charge. |
| 484 | Providing and supplying unbranded dining table of approved design and size, made from seasoned hardwood / MDF / engineered wood, with golden finish or coating, complete as directed by the Engineer-in-Charge. |
| 485 | Providing and supplying L-shaped Reception Table, make Keshav’s (Keshav Enterprises) or equivalent approved, of modern modular design, ergonomically constructed from high-quality materials, with durable finish, cable management provisions, and smooth edges, complete in all respects as directed by the Engineer-in-Charge. |
| 486 | Providing and supplying Computer Table with Additional Unit, make AARIHANT CRAFT – GLOBAL MARKETING or approved equivalent, made from high-quality pre-laminated boards with modern design, durable hardware, and fine finish, suitable for office, computer lab, or home workstation use, complete as directed by the Engineer-in-Charge. |
| 487 | Providing and supplying SAGAR SHREE FURNITURE Aluminium Powder-Coated Wicker Furniture, made of high-grade Aluminium frame (min. 1.2 mm thick) with polyester powder coating (min. 60 microns), woven with 100% virgin HDPE synthetic wicker (UV stabilized, all-weather resistant).Cushions made of high-density polyurethane foam (min. 32D) covered with 180 GSM polyester acrylic outdoor fabric, UV- and water-resistant.All fasteners of Stainless Steel (Grade 304).Furniture shall be weather-proof, corrosion-resistant, and suitable for outdoor use.Finish: Smooth, uniform, and scratch-resistant.Color and design as approved by Engineer-in-Charge.The item shall conform to relevant IS standards (IS:13871, IS:12775, ASTM G154).Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 488 | Providing and supplying DTS Sofa / Couch – 1 Seater, constructed with a hardwood internal frame (seasoned and chemically treated), high-density foam cushioning (min. 32D for seat, 28D for back), upholstered with premium fabric / leatherette of approved shade and texture.Armrests and seat edges to be smoothly contoured; bottom supported on sturdy wooden or metal legs with anti-skid buffers.All materials to be of IS-approved quality, joints glued and screwed for rigidity.Finish to be smooth, durable, and free from wrinkles or loose threads.Overall dimensions: approx. 900 mm (W) × 850 mm (D) × 850 mm (H) (±5%).Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 489 | Providing and supplying High-Back Revolving Chair, ergonomically designed with adjustable seat height and 360° revolving mechanism, mounted on a five-star nylon / metal base with twin-wheel castors for smooth mobility.Chair fitted with gas lift for height adjustment, tilt tension mechanism with locking system, and PU-moulded seat and back cushions upholstered with breathable fabric or mesh of approved shade.Backrest to be high-back type with lumbar support; armrests made of durable polypropylene / PU-padded material.All components shall be rust-free, sturdy, and smoothly finished for long operational life.Type: High-Back Revolving Chair with Adjustable Height and WheelsComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 490 | Providing and supplying Cafeteria Chair (Any Other Shape) with Armrest, made of ergonomically designed seat and back moulded from virgin polypropylene (PP) / high-grade plastic of approved colour and shape, supported on powder-coated mild steel / chrome-plated tubular frame of adequate thickness for stability and durability.Chair shall have integral / fitted armrests, smooth edges, and non-slip nylon glides at leg ends.The chair shall be lightweight, stackable, corrosion-resistant, easy to clean, and suitable for cafeteria / multipurpose seating use.All welds and joints shall be ground smooth and finished uniformly.Type: Cafeteria Chair – Any Other Shape with ArmrestComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 491 | Providing and supplying INTEGRITY SQUARE Cafeteria Chair with Armrest, having an ergonomically contoured seat and back made of injection-moulded virgin polypropylene (PP) / high-grade plastic of approved colour and finish, supported on a sturdy powder-coated / chrome-plated tubular steel frame of suitable gauge.The chair shall be fitted with integrated or fixed armrests, anti-skid nylon leg caps, and all welds shall be smoothly ground and rust-protected.The unit shall be lightweight, stackable, durable, corrosion-resistant, and easy to maintain, suitable for cafeteria, canteen, or public seating applications.Type: Cafeteria Chair with ArmrestComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 492 | Providing and supplying Unbranded Wooden Modern Dining Table, made from seasoned and chemically treated hardwood / engineered wood (MDF / particle board / plywood) with laminated or melamine-polished surface finish of approved shade and texture.The table shall be of modern design, sturdy construction, and smooth edges, supported on solid wood / metal legs with anti-skid buffers.All joints shall be glued and screwed, surfaces smoothly finished and sealed, and materials shall conform to relevant IS standards for furniture manufacture.The table shall be durable, termite-resistant, and easy to maintain.Make: Unbranded (as approved by Engineer-in-Charge)Type: Wooden Modern Dining TableComplete in all respects as per specifications and directions of Engineer-in-Charge. |
| 493 | Providing and supplying Door Curtains, made from premium woven fabric (minimum 260 GSM) in off-white colour, manufactured using high-quality yarn on handloom / powerloom, ensuring uniform texture, smooth finish, and colour fastness.Curtains shall be stitched with interlocked seams, hemmed edges, and fitted with eyelets or curtain tape as required for hanging.Fabric shall conform to IS:13717/1993 (Curtain and Upholstery Fabric – Cotton/Blended) standards.The material shall be washable, shrink-resistant, fade-resistant, and suitable for long-term institutional use.Type: Door Curtain, 260 GSM, Off-White ColourComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 494 | Providing and supplying Floor Standing Display Cabinet, fabricated from seasoned hardwood or high-quality engineered wood (MDF / particle board / plywood) of approved make and finish.Cabinet to have fully glazed doors made with 5 mm thick clear float glass fitted in wooden / engineered wood frame, with concealed hinges, magnetic catch, and lockable handle arrangement.The internal structure shall include adjustable shelves, polished / laminated on all visible surfaces with scratch- and stain-resistant finish of approved shade.The base shall be sturdy with level-adjustable legs or skirting for floor stability.All edges to be smoothly finished, and hardware (hinges, handles, screws) to be of stainless steel or equivalent corrosion-resistant material.Type: Floor Standing Display Cabinet with Glass in Wood / Engineered Wood Frame DoorComplete in all respects as per approved design, manufacturer’s specifications, and directions of Engineer-in-Charge. |
| 495 | Providing and supplying Drawer Type Steel Filing Cabinet, fabricated from prime quality CRCA (Cold Rolled Close Annealed) steel sheets of minimum 0.8 mm thickness for body and 1.0 mm for drawers, duly powder-coated (minimum 50–60 microns) in approved shade.Cabinet to be of standard office design, having multiple pull-out drawers (2/3/4-drawer type as specified) mounted on heavy-duty ball bearing telescopic slides for smooth and noiseless operation.Each drawer shall have a label holder, recessed handle, and central locking system to secure all drawers simultaneously.All edges and corners shall be rounded and free from burrs, and the unit shall rest on adjustable levelling glides.The cabinet shall be durable, rust-resistant, and suitable for foolscap / A4-size file storage.Material Finish: Powder-coated steel in grey / beige / approved colour.Type: Drawer Type Steel Filing CabinetComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 496 | Providing and supplying Mid-Back Chair with Fixed Armrest (without cushion and padding), made of ergonomically designed one-piece moulded seat and back from virgin polypropylene (PP) / high-quality plastic of approved colour and finish.The chair shall have integrated fixed armrests, supported on a strong powder-coated / chrome-plated tubular steel frame of adequate gauge for rigidity and stability.The surface shall be smooth, easy to clean, non-fading, and resistant to moisture and corrosion.All joints and welds shall be neatly finished and burr-free, with anti-skid nylon / rubber shoes on legs.The chair shall be lightweight, durable, and suitable for institutional / office / cafeteria use.Type: Mid-Back Chair with Fixed Armrest (without Cushion & Padding)Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 497 | Providing and supplying Low-Back Chair with Fixed Armrest and Padding, constructed with an ergonomically designed low-back frame made of tubular steel / metal section of suitable gauge, fitted with fixed armrests of polypropylene or PU material.Seat and back to be upholstered with high-density foam padding (minimum 32D for seat, 28D for back) and covered with fabric / leatherette upholstery of approved colour and shade.The chair shall have a rigid welded structure, anti-skid leg caps, and smooth, durable finish with powder coating (minimum 50 microns).All joints shall be strong, burr-free, and neatly finished.The chair shall be comfortable, sturdy, and suitable for office / institutional / visitor seating.Type: Low-Back Chair with Fixed Armrest and PaddingComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 498 | Providing and supplying Unbranded Wooden Modern Bed, fabricated from seasoned and chemically treated hardwood / high-quality engineered wood (MDF / particle board / plywood) of approved make and finish.The bed shall be of modern design, complete with headboard and footboard, sturdy frame construction with smooth edges and securely joined corners.The top structure shall support the mattress on solid wooden slats or flat board base, finished with laminated / melamine-polished / PU-coated surface of approved shade.All joints to be screwed and glued, free from sharp edges or warping.The bed shall be termite-resistant, durable, and easy to maintain, suitable for institutional or domestic use.Make: Unbranded (as approved by Engineer-in-Charge)Type: Wooden Modern BedComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 499 | Providing and supplying Single Wooden Bed with Headboard and Footboard, made from seasoned and chemically treated hardwood / high-quality engineered wood (plywood / MDF / particle board) of approved make and finish.The bed shall have a sturdy frame structure with smoothly finished headboard and footboard, all edges rounded and joints glued and screwed for rigidity.Top to have wooden slats or flat board base suitable for mattress placement.Visible surfaces to be laminated / melamine-polished / PU-coated in approved shade and texture.All components shall be termite-resistant, durable, and free from warping or sharp edges.The bed shall be of standard single size (approx. 900 mm × 2000 mm × 450 mm height) or as approved by Engineer-in-Charge.Type: Single Wooden Bed with Headboard and FootboardComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 500 | Providing and supplying Dressing Table with Cupboard and Open Shelves, made from seasoned hardwood / high-quality engineered wood (plywood / MDF / particle board) of approved make and finish.The unit shall consist of a mirror panel (minimum size 1200 mm × 450 mm) mounted on a sturdy wooden frame, integrated with a storage cupboard with hinged door(s) and open display shelves for utility items.All visible surfaces shall be laminated / melamine-polished / PU-coated in approved shade and texture.Edges shall be rounded and smoothly finished, and hinges, handles, and fittings shall be of stainless steel or other corrosion-resistant hardware.All joints shall be strongly fixed, neatly finished, and free from burrs or sharp edges.The dressing table shall be durable, termite-resistant, and aesthetically designed for residential or institutional use.Type: Dressing Table with Cupboard and Open ShelvesComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 501 | Bill No. XVIII: Electrical Works |
| 502 | EXTERNAL ELECTRICAL WORKSSupplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required3.5 core 50 Sq mm |
| 503 | 3.5 core 95 Sq mm |
| 504 | 3.5 core 120 Sq mm |
| 505 | 4 core 10 Sq mm |
| 506 | 4 core 16 Sq mm |
| 507 | 4 core 25 Sq mm |
| 508 | 3.5 core 185 Sq mm |
| 509 | 3.5 core 240 Sq mm |
| 510 | Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : -10 sqmm |
| 511 | 16 sq mm |
| 512 | 25 sq mm |
| 513 | 50 sq mm |
| 514 | 95 sq mm |
| 515 | 185 sq mm |
| 516 | 240 sq mm |
| 517 | Supplying and fixing of heat shrinkable straight through cable jointing kits of following sizes : -2 core 16 sqmm or 4 core 10/16 sq mm size |
| 518 | 3.5 core or 4 core 25/35 sq mm size |
| 519 | 3.5 core or 4 core 50 sq mm size |
| 520 | 3.5 core or 4 core 95 sq mm size |
| 521 | 3.5 core or 4 core 120/150 sq mm size:- |
| 522 | 3.5 core or 4 core 185 sq mm size:- |
| 523 | 3.5 core or 4 core 240 sq mm size:- |
| 524 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 525 | 160 mm dia (OD-160 mm & ID-135 mm nominal) |
| 526 | LT Panel :-Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and 900mm (NS) deep made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required for completeness and as per attached specification, direction of Engineer, CPWD standards and Electrical Inspectorate standards. (Only face area is to be measured)INCOMER1 No.600A FP MCCB(35 KA) (1 for main incomer)4 pole MCCB, 600A, Adjustable Microprocessor Release, 35KA for D.G incomer - 1nosMetering & Indication2 set of phase indicating lamps2 set of (0-500V) Voltmeter with VSS1 set of (0-160A) Ammeter with ASS with 3 no s.160/5A CTs1 set of (0-200A) Ammeter with ASS with 3 no s.200/5A CTsBUS-BAR 1 Set of 1000A TPN Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS 10 Nos.63 A FP MCCB (10KA) |
| 527 | Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum sub main distribution board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as following:. 4 pole MCCB, 160A, 35KA (1no.)as incomer analog type 0-100 amp ammeter of size 100x100 (NS)analog type 0-500 amp voltmeter of size 100x100 (NS)selector switch for voltmeterselector switch for ammetermeter230 volt LED type indicating lamp (3nos.)63A-TP (MCB) (6 no.), 32A-TP (MCB) (4),32A-DP (MCB) (4)for out going as outgoing |
| 528 | Design, Fabrication, Supply, Erection, Testing and commisioning of Powder coated, Weather Proof Double door type Feeder pillar fabricated out of 14 guage CRCA sheet steel in cubical, free standing, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Feeder pillar shall be treated with all anti-corrosive process before painting as per specification. Feeder Pillar shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels. Approval shall be taken for each panel before fabrication.direction of Engineer, CPWD standards and Electrical Inspectorate standards. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated)- Feeder Pillar:.INCOMER- 1No. 63A FP MCCB(35 KA) , 1No. 63A FP Contactor, AOM switch & Timers for 24 Hrs. settingMetering & Indication- 1 set of phase indicating lampsBUS-BAR- 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.OUTGOINGS-4 Nos. 32A FP MCB and 15 Nos. 6-32 SP MCB |
| 529 | Supplying, installation, testing and commissioning of following capacity diesel Generating Set (alternator directly coupled to diesel engine) compete in all respect broadly comprising of following and as per CPCB 2 norms (upto date ammended), including following specification. A. Alternator : Self excited, brush less type, of following capacity, 3 phase, 415 volts 50 Hz, 4 pole, AC alternator complete with all accessories.B. Engine : water cooled diesel engine of suitable BHP for rated alternator at 1500 rpm, turbo charged, direct injection type, 4 stroke, 4/6 cylinder including specified size fuel tank of approved design and shape duly calibrated and painted with one coat of primer and two coats of synthetic enameled paint of approved colour, residential type silencer with exhaust MS pipe (upto 2 metre beyond silenser) duly wrapped with asbestos rope of legging of specified quality and specification.C. AMF Panel Cubical, compartmentalized, AMF panel board with all suitable size power and control contactors, switches, meters and other accessories, internal wiring, connection, inter-connection etc. for trouble free smooth functioning of DG Set complete with battery charger and leads as per specification.D. Base Plate : Common base plate of required size for mounting of engine alternator set fabricated from MS channel and vibration damping arrangement with cushy foot mounting i/c painting etc. as per specification.250 KVA |
| 530 | Supply, Installation, Testing and Commissioning of Distribution Transformer (3ISLevel- ll)-DTR 250KVA 11/0.433KV as per TSECL Standards and Specification and providing all necessary connections as per the instructions of Engineer-in-charge. |
| 531 | INTERNAL ELECTRICAL WORKSWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.Group A |
| 532 | Group B |
| 533 | Group C |
| 534 | Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. |
| 535 | Wiring for light/ power plug with 2X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. |
| 536 | Wiring for light/ power plug with 4X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. |
| 537 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 538 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 539 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 540 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 541 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 542 | Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.Telephone wire 2 pair |
| 543 | Telephone wire 4 pair |
| 544 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 545 | Metal Telephone Junction Box 10 / 20 / 30 Pair |
| 546 | Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as required.19/20 mm dia |
| 547 | 25 mm dia |
| 548 | Supplying and fixing of the following electrical accessories including necessary connection etc. as required. - Angle/batten holder |
| 549 | Ceiling rose |
| 550 | Supplying and fixing of the following sizes GI (in recess) and plastic (on surface) modular switch boards etc. as required. - 1-2 module GI switch board:- |
| 551 | 3 module GI switch board:- |
| 552 | 4 module GI switch board:- |
| 553 | 6 module GI switch board:- |
| 554 | 8 module GI switch board:- |
| 555 | 12 module GI switch board:- |
| 556 | Supplying and fixing of the following sizes modular type cover plates for GI/Plastic modular switch boards etc. as required. - 1-2 module :- |
| 557 | 3 module :- |
| 558 | 4 module :- |
| 559 | 6 module :- |
| 560 | 8 module :- |
| 561 | 12 module :- |
| 562 | Supplying and fixing of the following modular accessories including necessary connection etc. as required. - 6/10 amps one way SP switch (1M) |
| 563 | 6/10 amps two way SP switch (1M) |
| 564 | 16/20 amps one way SP switch (1M) |
| 565 | Bell push SP (1M) |
| 566 | 32 amps one way DP switch (2M) |
| 567 | 3 pin 6/10 amps socket outlet (2M) |
| 568 | 3/6 pin 16/20 amps socket outlet (2M) |
| 569 | 3/6 pin 25 amps socket outlet (2M) |
| 570 | 5 step fan regulator (2M):- |
| 571 | RJ11 telephone socket outlet (1M):- |
| 572 | RJ45 LAN socket outlet (1M):- |
| 573 | TV socket outlet (1M):- |
| 574 | Buzzer call bell (1M) |
| 575 | 20/25 amps single phase motor starter switch (2M) |
| 576 | Supply, Installation, Testing and Commissioning of 1200MM ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal (Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies,hackle kit, safety rope, copper winding, steel/Al body.Power Factor not less than 0.9, Service Value(CM/M/W) minimum as below, 350 RPM (tolerance asper IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based)for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/cexternal connections with 1.5 sq.mm FRLS/HFFR,PVC insulated copper conductor single core cableand earthing etc. as required.1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) |
| 577 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape, including painting the exposed portion as per standard drawing complete as required (provided incase of low ceiling height) |
| 578 | Supplying & installation of 225/230 mm sweep metalic body exhaust fan including connection etc as required:- |
| 579 | Supplying, installation, testing and commissioning of following of solar water heating system with heat exchanger type including electrical heater backup,make up water tank but without piping including necessary connection etc as required. |
| 580 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):-Surface mounted integrated 10 watt LED batten with polycarbonate diffuser:- |
| 581 | Surface mounted integrated 20 watt LED batten with polycarbonate diffuser:- |
| 582 | Recessed/Surface mounted 2ft x 2ft decorative 36 watt LED panel light with integral driver and high quality polycarbonate diffuser:- |
| 583 | Recessed round/Square shaped 18 watt LED downlight with integral driver and high quality polycarbonate diffuser:- |
| 584 | Surface mounted round/Square shaped 6/7 watt LED downlight with integral driver and high quality polycarbonate diffuser:- |
| 585 | Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required.(2+4) / 6 way SPN MCB DB (double door) |
| 586 | 6 way horizontal TPN MCB DB (Double door):- |
| 587 | 8 way horizontal TPN MCB DB (Double door):- |
| 588 | Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:-6 to 32 amps SP MCB:- |
| 589 | 40/50/63 amps TPN MCB:- |
| 590 | Supplying, installation, testing and commissioning of following ratings online UPS with inbuilt isolation transformer, 50/60Hz (Auto sensing) frequency, P.F range 0.95-0.99, voltage regulation +/-1%, Pure sine wave form, total harmonic distortion < 5% with full load, Noise level 50db at 1m, LED indication for Normal mode/Load on battery/Load on bypass/System fault, Audible alarm for Mains failure, low battery, Overload, fault and Bypass mode complete with M. S Rack for mounting battery bank, Battery inter link cables and all other necessary accessories including connections etc. as required:-10 kVA, 3 Ph input/1 Ph output Online UPS with 28800 VAH battery bank for minimum 2 hours Backup:- |
| 591 | SITC of 43-inch or above LED Display,Resolution : 3840*2160 (4K UHD),Brightness(Typ.): 350 nits or better Contrast Ratio : 5000:01:00 or better ,Viewing Angle(H/V) :178/178Response Time(G-to-G) :8ms(Typ.) or better ,Operation Hour : 16/7,Haze : 2%, Input : DVI-D,HDMI 2.0 (2),HDCP 2.2,Stereo Mini Jack, DVI/HDMI/Audio(Common),USB 2.0 x 2,Output:Stereo Mini Jack,RS232C(in/out) thru stereo jack, RJ45,IR Special Features :H/W: Temperature Sensor,Pivot Display, Clock Battery(168hrs Clock Keeping), Built in Speaker(10W 2ch or better), IP5x, Wi-Fi/BT S/W: Auto Source Switching & Recovery, Button Lock, Hot key option, Plug&Play (Initial Setting) remote control etc with wall mounting bracket. |
| 592 | Supplying and fixing following of split Inverter type Air Conditioner unit with cooling unit (copper coil) and condensing unit (copper coil) including 5 years compressor warranty and standard length of upto 5 metre of copper piping with insulation etc complete as per specification:2.0 Ton split type Inverter AC {5 Star} |
| 593 | Supplying and fixing following Small Fridge, Big Space : Fitted with a bottle bin that accommodates 2-litre bottles and a wire shelf to easily organize items mini bar freeze 55 litre as required |
| 594 | Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/recessed steel/ PVC conduit as required.2 Pair |
| 595 | 4 Pair |
| 596 | Supplying following grade co-axial TV cable FR PVC insulated, shielded with fine tinned copper braid and protected with PVC sheath cable in company pack coils.RG-11 grade |
| 597 | Suppy, installation, testing & commissitioning and putting into operation and final testing of MACHINE ROOM LESS TYPE automatic lift complete with ARD and all standard equipments, accessories and control equipments as per manufacturer's design and as per CPWD specification (Part III LIFTS) and fulfilling following requirments on turn key basis.A. Type : Passenger lift B. Load : 4 passenger/ 272 KgC. Speed : 1.0 metre per second D. Contol : AC2E. Operation : Microprosser based simplex collective selective with/without lift attendentF. Total rise : About 8 mtrs G. Landings : 4 All on same side H. Floors served : G,1,2,3I. Signals : Digital car position indicator, car travel direction indicator in car & at all landingsJ. Lift shaft size : About 1800 mm width X 1600 mm depth, finished with plaster (size as per actual site conditions)K. Lift car size : About 1000 mm width X 1100 mm depth x 2200 mm HL. Car entrance : Clear opening 700 mm wide X 2000 mm high protected with car doorM. Landing entrance: Clear opening 700 mm wide X 2000 mm high protected with landing doorN. Car door : Stainless steel /Glass Door two pannel telescopic/centre opening flush typeO. Landing door : Stainless steel /Glass Door two pannel telescopic/centre opening flush type P. Door operation: Automatic electric power operated door with infra red protectionQ. Car interior : Stainless steel pannel with hair line/ mirror/moon rock finish on all sidesR. Car floor : Hard wood covered with PVC/ marblex tilesS. Car ceiling & lighting : Fluorscent lighting concealed by suspended false ceiling with plain acrylic diffuser. The frame of suspended false ceiling shall be of powder coated aluminiumT. Car ventilation : Pressure fan with anodised aluminium grillU. Emergency lighting in car: Battery operated Emergency lighting in the lift carV. Intercom system : Battery operated Intercom system in lift car, machine room and control roomW. Emergency alarm : Battery operated alarm bell system in lift car & contol roomX. Electric power supply : AC 415 Volts 3 phase 50 Hz terminated in machine roomY. Fire man switch : Fire man switch at main landing termanal |
| 598 | EXTERNAL LIGHTSEarthing with 40 mm dia G.I. Earth pipe (medium gauge) 4.5 m. long complete with masonry enclosure on top CI cover plate size 12\\"x 12\\" having locking arrangement including CC work, holes on earth pipe etc. as required. |
| 599 | Extra for using salt (5 kg) and charcoal (46kg) for pipe earth electrode as required. |
| 600 | Earthing with Copper earth plate 600 mm x 600 mm x 3 mm thick i/c accessories and providing masonry enclosure with CI cover plate Size 12\\"x 12\\" having locking arrangement, along with 20 mm dia (medium gauge) watering pipe including CC work etc as required:- |
| 601 | Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick i/c accessories and providing masonry enclosure with CI cover plate Size 12\\"x 12\\" having locking arrangement, along with 20 mm dia (medium gauge) watering pipe including CC work etc as required:- |
| 602 | Proving and fixing / drawing of 4.06 mm dia (8 SWG) G.I. wire on surface or in existing G.I/ PVC/ Polythene pipe for loop earthing as required. |
| 603 | Earthing with 40 mm dia G.I earth pipe (medium gauge) ( above 4.5m longnormal size) i/c necessary hole etc as required |
| 604 | Supply and fixing of 25mm x 5mm GI strip on wall/ floor of the building for horizontal/ vertical run including necessary spacers and porcelain insulators at regular intervals. |
| 605 | Supply and fixing of 32mm x 6 mm GI strip on walls/ floor of the building for horizontal/ vertical run including necessary spacers and porcelain insulators at regular intervals |
| 606 | Supply and fixing of 25mm x 3mm Copper on walls/ floor of the building for horizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals. |
| 607 | Providing, fixing and laying rigid UPVC pipes conforming to IS : 4985 jointing with couplers, of same class conforming to IS : 10124 ( Pt-II ) with solvent cement conforming to IS : 14182 including testing of joints complete ( but excluding the cost of specials like bend, tees etc. which will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge.Class - 3 ( working pressure 6.0 kg / cm2)40 mm OD |
| 608 | 63 mm OD |
| 609 | Supplying and fixing of the following sizes PVC conduit (medium gauge) on surface with all accessories etc. as required.25 mm dia |
| 610 | Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required2 core 10 Sq mm |
| 611 | Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : -10 sq mm |
| 612 | 16 sq mm |
| 613 | 50 sq mm |
| 614 | Supply installation and commissioning of 12W recessed mounted niche light fixture designed to provide uniform illumination for low mounting heights where guidance and security lighting is required. Sustainable LED technology offers durability and optimal light output with low power consumption. Luminaires made up of pressure die-cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. Non yellowing UV stabilized semi-translucent acrylic/clear polycarbonate with EPDM/Silicone gasket.Die cast aluminium installation housing for mounting on wall. Cable entries for through wiring of main supply cable. Integral constant current power supply. Lumen output 150lm/w, Mac Adam step 3 LED, CRI>80, L70-B10-60000h@ Ta 25°C, IK09, IP65. Power factor >0.95, THD<10, Surge Protection upto 2.5KV, driver efficiency >85%. Operating Temperature of the luminaire is -15°C~ 50°C, Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection. Available CCT 3000K/4000K/5700K. Product finsih available: Pure polyester powder coated Graphite grey, Anthracite grey, Jet black. Product should be BIS and CE Certified. |
| 615 | Supply installation and commissioning of contemporary design Single arm Lighting Pole with inbuilt 60WX1 LED Modules of 6000mm Height, arm length 1145mm, made out of hot rolled steel grade E250, as per IS 2062:2011 and designed suitably for wind speed upto 50m/s wind conforming to IS 875: PART -3:1987. the square base plate of MS (grade E250) of size 300mmx300mm, 16mm thick and facilitated with 4 elongated slots 48mm x 24mm at CC 215X160mm to suit the 500mm, J-type, M20 bolts (Grade 4.6). The cable entry hole Ø70mm is provided at the centre of the baseplate. A base compartment for weather proof control box is provided at a height 300mm above the base plate with a die cast door contoured to the poles's shape housing the gear tray, pre-wired with 2.5 Sq.mm cable, Siemens/Anchor make MCB, terminal connectors for loop in loop out arrangement. The surface preparation of the pole & components shall be done by shot blasting which is environmentally safe eliminating the chemical and acid use and ensuring the thorough removal of impurities like rust, oxides and other unwanted particles from the surface for high standard coating. The surface finish of the pole shall be Zinc rich primer coat & pure polyester powder coating providing 60 Microns DFT. Pole consist of module based luminaire each 60W(Min IP68) with minimum delivered lumens of 110lm/W with led life span of L70 / B10 @ 60000 Hrs, SDCM ≤ 3, Type III light distribution, IK09, Operating Temperature of the luminaire is -40°C~ 50°C, Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection and self restart feature in case of over / under voltage and phase to phase voltage, driver efficiency > 85%, Power factor >0.9, THD <10% . Available CCT 3000K/4000K/5700K. Product finsih available: Pure polyester powder coated Graphite grey, Anthracite grey, black. Product should be BIS and CE Certified. |
| 616 | Supply installation and commissioning of Lighting Pole of 4000mm Height suitable for mounting light luminaires Poles can stylishly convey the identity of any landscape. , made out of hot rolled steel grade E250, as per IS 2062:2011 and designed suitably for wind speed upto 50m/s wind conforming to IS 875: PART -3:1987. The pole profile extends from the square base plate of MS (grade E250) of size 200mmx200mm, 12mm thick and facilitated with 4 elongated slots 38mm x 19mm at CC 140mm to suit the 300mm, J-type, M16 bolts (Grade 4.6). The cable entry hole Ø70mm is provided at the centre of the baseplate. The pole size shall have Ø76 mm and base size Ø139.7 mm. A base compartment for weather proof control box is provided at a height 260mm above the base plate with a die cast door contoured to the poles's shape housing the gear tray, prewired with 2.5 Sq.mm cable, Siemens/Anchor make MCB, terminal connectors for loop in loop out arrangement. The surface preparation of the pole & components shall be done by shot blasting which is environmentally safe eliminating the chemical and acid use and ensuring the thorough removal of impuritise like, rust, oxides and other unwanted particles from the surface for high standard coating. The surface finish of the pole shall be Zinc rich primer coat & pure polyester powder coating providing 60 Microns DFT. Any other wiring/electrical consumables shall be under the scope of purchaser. Product finsih available: Pure polyester powder coated Graphite grey, Anthracite grey, black. Product should be CE Certified. |
| 617 | Supply of an elegant and efficient 50W Lantern with toughened glass diffuser provide a unique comfortable light choice with symmetrical and glare free light distribution. Aesthetically designed sturdy construction ensure a long life against all weather condition, maintaining initial performance through lifetime of installation. The luminaire compromises of specially contoured spun aluminium top cover. The lamp along with control gear is housed inside and covered with a toughened glass diffuser at the top portion of extruded aluminium tube and the bottom portion attached to a mounting base. Lamp compartment encased in non-yellowing clear/ translucent UV stabilised acrylic diffuser. Die cast aluminium spigot base with aluminium alloy of low copper content for effective corrosion resistance. Suitable for mounting on 101 mm OD Pipe. Integral constant power supply. Product benefits are elegant, robust design, environmental friendly, moisture proof, insect free, low maintenance cost, reduces glare with minimum delivered lumens of 150lm/W with led life span of L70-B10-60000h@ Ta 25°C Mac Adam step 3 LED, IP65, CRI≥80, Power factor >0.95, THD<10, Surge Protection upto 6KV, Efficiency >89%. Operating Temperature of the luminaire is -15°C~ 50°C, Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection. Available CCT 3000K/4000K/5700K. Product finsih available: Pure polyester powder coated Graphite grey, Anthracite grey, Jet black. Product should be BIS and CE Certified. |
| 618 | Supply installation and commissioning of double arm Lighting Pole 4000mm Height. Made out of hot rolled steel grade E250, as per IS 2062:2011 and designed suitably for wind speed upto 50m/s wind conforming to IS 875: PART -3:1987. the square base plate of MS (grade E250) of size 230mmx230mm, 12mm thick and facilitated with 4 elongated slots 38mm x 19mm at CC 180mm to suit the 300mm, J-type, M16 bolts (Grade 4.6). The cable entry hole Ø70mm is provided at the centre of the baseplate. A base compartment for weather proof control box is provided at a height 300mm above the base plate with a die cast door contoured to the poles's shape housing the gear tray, pre-wired with 2.5 Sq.mm cable, Siemens/Anchor make MCB, terminal connectors for loop in loop out arrangement. The surface preparation of the pole & components shall be done by shot blasting which is environmentally safe eliminating the chemical and acid use and ensuring the thorough removal of impurities like rust, oxides and other unwanted particles from the surface for high standard coating. The surface finish of the pole shall be Zinc rich primer coat & pure polyester powder coating providing 60 Microns DFT. Any other wiring/electrical consumables shall be under the scope of purchaser. Product finsih available: Pure polyester powder coated Graphite grey, Anthracite grey, black. Product should be CE Certified. |
| 619 | Supply installation and commissioning of an elegant and efficient 30W Lantern with translucent diffuser provide a unique comfortable light choice with symmetrical and glare free light distribution. Aesthetically designed sturdy construction ensure a long life against all weather condition, maintaining initial performance through lifetime of installation. The luminaire compromises of specially contoured spun aluminium top cover. The lamp along with control gear is housed inside and covered with a toughened glass diffuser at the top portion of extruded aluminium tube and the bottom portion attached to a mounting base. Lamp compartment encased in non-yellowing clear/ translucent UV stabilised acrylic diffuser. Die cast aluminium spigot base with aluminium alloy of low copper content for effective corrosion resistance. Suitable for mounting on 60mm OD Pipe. Integral constant power supply. Product benefits are elegant, robust design, environmental friendly, moisture proof, insect free, low maintenance cost, reduces glare with minimum delivered lumens of 150lm/W with led life span of L70-B10-60000h@ Ta 25°C Mac Adam step 3 LED, IP54, IK06, CRI≥80, Power factor >0.95, THD<10, Surge Protection upto 4KV, driver efficiency >87%. Operating Temperature of the luminaire is -40°C~ 50°C, Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection. Available CCT 3000K/4000K/5700K. Product finsih available: Pure polyester powder coated Graphite grey, Anthracite grey, Jet black. Product should be BIS and CE Certified. |
| 620 | Supply of LEDcompact and robust flood light luminaire Input power : 30W designed to provide uniform illumination in open spaces. Beam angle 10° / 28° / 45°. Extruded aluminium hood cover integrated with die-cast module and extruded aluminium alloy tube (grade 6063), excellent thermal management heat sink & polycarbonate optical lens. Adjustable clamp made of stainless steel (2mm thickness) to facilitate proper aiming of the luminaire at desired angle. Pressure die cast aluminium mounting plate Ø100.5 x 4mm thick with 2 elongated holes 15 x 10 to suit M8 bolts at PCD 55 with pure polyester powder coating. This mounting plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. Cable entrance via PG9 cable gland. All external screws are made of stainless steel. Protection class IP66 for LED Module. Mechanical resistance IK10. Pure polyester powder coated RAL 9004 Black, RAL9007 Grey aluminium, RAL 7016 Anthracite grey, Graphite grey. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. K-Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD< 10%, Surge protection 4KV. Luminaire dimension : 166mm diameter x 168mm width x 584mm height. CE & BIS Certified. Inhouse NABL accredited lab. |
| 621 | Supply installation and commissioning of 12w energy efficient In-ground recessed luminaire’s are designed to create luminous walkways, or accentuate architecture elements in facades and landscapes providing distinctive lighting effects. Made of die cast aluminium, SS body, scratch resistance glass and special optics makes these luminaires perfect for creating very defined effects of accent lightwith honeycomb louver. Luminaire body and screwless front ring made from solid billet of 316 grade stainless steel. Silicone seal gasket ensuring IP67 rating, step tempered glass diffuser 4mm thickness. Clear Polycarbonate optical lens. Luminaire hard wired with 3x0.5mm² cable of 1mts length, supplied with mounting sleeve for preparing recessed opening in ground or wall. Safety Class III. Non-integral constant current power supply. Available beam angle 15°, 25° & 40°, Mac Adam step 3 LED, CRI>80, L70-B10-60000h@ Ta 25°C, IK09, IP67. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%, Surge protection 4KV , Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection. Available CCT 3000K/4000K/6500K. High luminous efficiency at reduced wattage. Supplied with IP68 rated connector for a secure connection to the network, ABS Plastic outer costing for easy installation. Product should be BIS and CE Certified. |
| 622 | Supply installation and commissioning of 16w environmentally friendly LED garden and pathway luminaires to create a pleasant light distribution with a high degree of visual comfort. Theses luminaires offer shielded glare free illumination on ground surface and are perfect for illuminating entrance, footpaths as well as garden and landscape architecture. Clean lines and pure form are the underlying elements if this series of LED bollards, designed to provide radially symmetric light emission of 360° . Luminaire body made of extruded aluminium alloy (grade 6063) with die cast aluminium components and non corrosive SS fasteners. Reflector system made of spun aluminium (powder coated). Non yellowing UV stabilised acrylic/ polycarbonate diffuser. Silicone gasket. Luminaire supplied with2/3 core cable length and IP67 connector. Mounting plate die cast aluminium double powder coated with an anchorage unit and stainless steel fixing screws. High luminous efficiency at reduced wattage. Elegant and robust design, dark sky compliant protects pedestrians from glare by preventing spill light above the horizontal plane. Cable entries for through wiring of main supply cable. Integral constant current power supply , pre-wired with LED driver and suitable for operating on 240V 50 Hz single phase AC supply. Lumen output 150lm/w, Mac Adam step 3 LED, CRI>80, L70-B10-60000h@ Ta 25°C, IK08, IP65. Power factor >0.95, THD<8, Surge Protection upto 3KV, driver efficiency >87%. Operating Temperature of the luminaire is -15°C~ 50°C, Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection. Available CCT 3000K/4000K/5700K. Product finsih available: Pure polyester powder coated Graphite grey, Anthracite grey, Jet black. Product should be BIS and CE Certified. |
| 623 | Supply installation and commissioning ceiling mounted compact downlight. Beam angle 15° / 25° / 40°. Luminaire made of extruded aluminium, pressure die-cast aluminium alloy of high corrosion resistance and external non corrosive stainless steel fasteners. Clear toughened glass of 4mm thickness. Polycarbonate optical lens. Gravity die cast aluminium plate for surface mounting on ceiling. Single cable entrance via PG7 cable gland. Protection class IP65. Mechanical resistance IK07. Pure polyester powder coated RAL 9004 Black, RAL9007 Grey aluminium, RAL 7016 Anthracite grey, Graphite grey. Available colour temperature 2700K / 3000K / 4000K / 6500K, Colour rendering index (CRI)90. K-Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >80%, Power factor >0.95, THD <10%, Surge protection 4KV. Luminaire dimension : 100mm diameter x 150mm height. CE & BIS Certified. Inhouse NABL accredited lab. |
| 624 | Supply installation and commissioning of Flexible LED Strip White led color 12Vdc / 24Vdc CRI >80 MacAdam step 3 Input power : 12W Dimension 1000 x 12 mm Beam angle : 120° Electronic driver ON/OFF (External driver)IP rating IP67MATERIAL CHARACTERISTICSCopper coated flexible strip, Silicone moulded diffuser, End cap LIGHTING PERFORMANCESilicone moulded diffuserThis luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire >10,000 hours at 40ｰC. Operating ambient temperature range is from -15ｰC to +50ｰC. Driver efficiency >85%, Surge protection 3KV. Product should be BIS and CE Certified. |
| 625 | 100 watt Side mounted street light luminaire. Type II (Asymmetrical light distribution). Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive stainless steel fasteners. Clear toughened glass. Protection class IP66. Mechanical resistance IK08. Pure polyester powder coated RAL 9004 Black, RAL9007 Grey aluminium, RAL 7016 Anthracite grey, Graphite grey. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>70. SDCM-3 MacAdam. K-Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.97, THD <10%, Surge protection 6KV. Suitable for mounting on to 60 mm dia pipe at lateral (side entry). Luminaire dimension : 526mm length x 174mm width x 90mm height. CE & BIS Certified. Inhouse NABL accredited lab. |
| 626 | Bill No. XIX: CCTV Work |
| 627 | CCTV WORK: Supplying , installation , testing and commissioning of 4 MP Bullet Camera weather & dust proof IP based Fixed Lens day/night Camera (IP67 , IK 10) , 1/3” 4MP PS CMOS Image Sensor, H.265 and H.264 triple-stream encoding, WDR(120dB), Day/Night Support, UL ,CE FCC Certified as per the specifications. |
| 628 | 2 MP PTZ Camera - Providing installation testing and commissioning weather & dust proof IP based Dome PTZ (Pan Tilt & Zoom) true day & night camera, 1/2.8” 2MP PS CMOS Image sensor, Max. 50/60fps@1080P, Color: [email protected]; [email protected] (IR on), Powerful 45x (3.95~177.7 mm) Optical and 16x Digital zoom, WDR(120dB), 3D DNR, Day/Night (ICR), Defog, ROI, EIS, AGC, BLC, HLC, Support Starlight Function, Up to 300 presets, auto scan, 8 tour, 5 pattern, auto pan, Tripwire, Intrusion, Abandoned/Missing, Face Detection, Heat Map, IR Range of 200 Mtr., Max 300°/s pan speed, 360° endless pan rotation, Built-in 7/2 alarm in/out, Micro SD card 256GB, IP67, IK10, Support PoE+, UL, CE ,FCC certified |
| 629 | Supply, Installation, Testing and Commissioning of 32 Channel NVR 4 Sata port-Upto 8 TB; 32 Channel IPcamera input, Quad Core embedded Processor and LINUX Embedded; 16 POE; Max 200 Mbps incoming & outgoing bandwidth, Smart H.265/ H.264 codec decoding, Upto 8 MP resolution preview and playback, Frame Rate: 1-15 FPS(8 MP); 1-25/30 fps for rest of Resolutions; Support 4 SATA HDDs up to 8 TB each, 2 USB (1 USB3.0,1 USB2.0), 1HDMI /1 VGA simultaneous video output , Two way talk 1Channel Input, 1Channel Output RCA, 1RJ-45port (10/100/1000Mbps), |
| 630 | Supplying , installation , testing and commissioning of 8 Port Managable PoE Switch 10/100/1000 8 Port with 2 Giga SFP uplink, L2 Managed PoE switch, Power Budget max 96 W, single port 30 W, AI Extend, Al VLAN as per the specifications. |
| 631 | Supplying , installation , testing and commissioning of 9U Indoor Rack Wallmount 9U 630D With Front Glass Door Lock & Key 550 9U - (with 1U cable Manager;Fan;6 socket PDU) complete as required. |
| 632 | Supplying , installation , testing and commissioning of 6 TB Surveillance Hard disk drive Complete as required |
| 633 | Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/concealed Steel/FRLS PVC conduit as per specification. |
| 634 | Supply, installation and testing for HDMI cable. |
| 635 | Supply of swaged steel tubular pole as per IS 2713 with base plate of size 300x300x6mm welded at bottom, necessary hole for cable entry and earthing stud welded at specified height including painting with one coat of red oxide zinc chromate primer.Designation 410 SP-2 height 7.00 metre |
| 636 | Supply, installation, testing and commissioning of 2MP Outdoor IP66 PTZ Camera with 4.5-135 mm Lens, 120dB WDR, 30X Optical Zoom, 100 Meter IR Range, ONVIF Profile S & G PTZ Camera, CE FCC and UL certified as per specification of Engineer in charge. |
| 637 | Supplying, installation testing and commissioning of standard/ short/long throw multimedia projector with display device- DLP technology and above, minimum No. of pixels 1024x768, computer compatiblity- UXGA/WXGA/SXGA/XGA, minimum life of light source-5000 hours, network terminal wired/ wireless with inbuilt speaker including all accessories and specifications as per site requirement.Brightness: 4000 Lumens |
| 638 | Supply and installation of Wallmount motorized projector screen, 1080p, 3D and 4k supported display technology, including all accessories and specification as per site requirement |
| 639 | Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as required.25 mm dia |
| 640 | Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.Above 6.5 metre and upto 8.0 metre |
| 641 | Bill No. XX: Fire Fighting |
| 642 | Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.200 mm. dia |
| 643 | 150mm dia. |
| 644 | 100mm dia. |
| 645 | 80mm dia. |
| 646 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :25 mm dia |
| 647 | 80mm dia. |
| 648 | 100 mm dia |
| 649 | 150 mm dia |
| 650 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 651 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :100 mm dia |
| 652 | 150mm dia. |
| 653 | 200 mm dia. |
| 654 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately):80 mm dia |
| 655 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100 mm dia |
| 656 | 150 mm dia |
| 657 | 200 mm dia. |
| 658 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :100 mm dia |
| 659 | 150 mm dia |
| 660 | 200 mm dia. |
| 661 | Supply, installation, testing and commissioning of ball valve (brass) high or low pressure withplastic floats inclusive of all necessary required material, labor for mentioned below size.20.00 mm OD |
| 662 | 25.00 mm OD |
| 663 | Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia and with necessary G.I. coupling, valve to be fitted on top of Air vessel or on wet riser as per specification. |
| 664 | Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.(a) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS:12585(b) 20 mm nominal internal dia gun metal globe valve & nozzle.(c) Drum and brackets for fixing the equipmets on wall.(d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.30 m |
| 665 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Gunmetal |
| 666 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. |
| 667 | Supplying and fixing 63 mm dia, 15 mtr long Flax canvas hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required. |
| 668 | Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required.Size 600 mm x 600 mm x 500 mm |
| 669 | Providing and fixing fire brigade 63mm dia GM suction coupling to 100/150 mm dia suction pipe complete. |
| 670 | Providing and fixing standard fireman's axe (tested for 20000 Volts) with heavy insulated rubber handle. (ISI marked) |
| 671 | Supplying G.l. Fire buckets with round bottom having at least 9 lit. capacity duly painted with one coat of zinc cromate primer and 2 coat of synthetic enamel paint of post box red colour and filled with dry sand and kept on provided wall hook or stand etc complete. |
| 672 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :4 way - 150 mm dia M.S. Pipe |
| 673 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) |
| 674 | Centering shuttering including struttings, propping etc. and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with steel formwork |
| 675 | UGR(UNDER GROUND RESERVIOR)Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff with complete lead and lift including dressing and leveling of pits.All kinds of soil |
| 676 | Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M. |
| 677 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) -PCC for tank |
| 678 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification |
| 679 | Centering shuttering including struttings, propping etc. and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with steel formwork |
| 680 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply (For retaining wall) |
| 681 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 682 | Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete as required as per direction of the Engineer-in-charge:Serrated with central bulb (225 mm wide, 8-11 mm thick) |
| 683 | Supplying and fixing C.I. cover without frame for manholes :455 x 610 mm rectangular C.I. cover (light duty)the weight of the cover to be not less than 23 kg. |
| 684 | Providing, hoisting and fixing in position inverted „J‟ type 100 mm dia. C.I. Cowl type ventilators with mosquitoproof aluminium mesh at top including applying 2 coats of anti-corrosive paint, etc. complete as directed by Engineer-in-charge, weighing not less than 35 Kg. |
| 685 | Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 :Upto 300 mm dia. |
| 686 | Pump houseProviding and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) |
| 687 | Centering shuttering including struttings, propping etc. and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with steel formwork |
| 688 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply (For retaining wall) |
| 689 | Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete as required as per direction of the Engineer-in-charge:Serrated with central bulb (225 mm wide, 8-11 mm thick) |
| 690 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification |
| 691 | Providing and fixing in position MS Puddle collar (approx. 1m length) inside the wall including all material labour as per Technical Specifications and as per direction of Engineer. 300 mm dia. Pipe |
| 692 | Providing and fixing Galvanized chicken mesh (24 guage, 12 mm size) properly stretched and nailed ensuring equal thickness of plaster at junction of masonry work and concrete members. |
| 693 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.Fixed to steel windows by welding. - Wt: @20kg/sqm |
| 694 | Providing and fixing in position 1mm thick M.S. sheet sliding-shutters with frame and diagonal braces of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junction and corners 25mm dia pulley, 40x40x6mm angle and T-iron guide sufficiently long at the top and bottom respectively, channels & with bolts, nuts, rivets, locking arrangement, stoppers, handles, hold fast including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required. |
| 695 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required:-Using M.S. angels 40x40x6 mm for diagonal braces. |
| 696 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 697 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 698 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new work |
| 699 | Grouting of Retaining wall in cement grouting mass as per direction of Engineer Incharge. |
| 700 | Providing, installation of Hand operated overhead traveling crane on turn key basis of capacity 3 Tonnes, all including Horizontal & longitudinal girder size: ISMB200, square bar for top of the longitudinal girder, the hoist & trolley, which traverses across the Horizontal & longitudinal and lifts up and down, two set of chain pulley (single girder type crane having Horizontal and longitudinal motion along the entire length of pump house.) including all material and labour etc. and commissioning as per Technical Specifications and as per direction of the engineer. Room size inner: 10.5m x 6.5m |
| 701 | Electrical Work Pump RoomSupplying & fixing of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:-6 to 32 amps FP MCB |
| 702 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.Group A |
| 703 | Group B |
| 704 | Group C |
| 705 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 706 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 707 | 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 708 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 709 | Supplying and fixing of the following sizes electrical acessries including necessary connections etc. as required. - Ceiling Rose |
| 710 | Supplying and fixing of the following sizes GI (in recess) and plastic (on surface) modular switch boards etc. as required.1-2 module GI switch board:- |
| 711 | 3 module GI switch board:- |
| 712 | 4 module GI switch board:- |
| 713 | Supplying and fixing of the following sizes modular type cover plates for GI/Plastic modular switch boards etc. as required.1-2 module |
| 714 | 3 module |
| 715 | 4 module |
| 716 | Supply, Installation, Testing and Commissioning of 1200MM ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal (Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies,hackle kit, safety rope, copper winding, steel /Al body.Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance asper IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/cexternal connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required.1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) |
| 717 | Supplying and fixing of the following modular accessories including necessary connection etc. as required.5 step fan regulator (2M):- |
| 718 | Supplying and Installation of 300 mm sweep metalic body exhust fan including connection etc. as required. |
| 719 | Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as reqd. - 20 mm |
| 720 | Supplying and fixing of powder coated sheet steel enclosure on surface/recess, suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required(2+4) / 6 way SPN MCB DB (double door) |
| 721 | 8 way TPN MCB DB (single door):- |
| 722 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):-Surface mounted integrated 20 watt LED batten with polycarbonate diffuser |
| 723 | Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required4 core 16 Sq mm |
| 724 | 3.5 core 50 Sq mm |
| 725 | 3.5 core 95 Sq mm |
| 726 | Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : -16 sq. mm |
| 727 | 50 sq. mm |
| 728 | 95 sq. mm |
| 729 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required 300 mm width X 50 mm depth X 1.6 mm thickness |
| 730 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required 300 mm width X 50 mm depth X 1.6 mm thickness |
| 731 | Mechanical Work For Pump HouseProviding, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :80 mm dia |
| 732 | 100 mm dia. |
| 733 | 150 mm dia. |
| 734 | 200 mm dia (wall thickness 6.3 mm) |
| 735 | 300 mm dia (wall thickness 7.1 mm) |
| 736 | Providing, installation, testing and commissioning of Circular Bellow, Grade: SS 304 section moulded to shape and fitted with a rotatable coated steel flange to each end for connection to flanged pipework.150 mm dia |
| 737 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete :25 mm nominal bore |
| 738 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid eparately):50 mm dia |
| 739 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 740 | Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 : 200 mm dia |
| 741 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.100 mm dia |
| 742 | 150 mm dia |
| 743 | Providing and fixing CIDF Butterfly valve with bolts, nuts, rubber insertions etc. complete as per CPWD specification and direction of the Engineer - in - charge. ( The tail pieces, tappers etc if required will be paid separately )150 mm dia |
| 744 | 200 mm dia |
| 745 | 300 mm dia. |
| 746 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :80 mm dia |
| 747 | 150mm dia. |
| 748 | 200mm dia. |
| 749 | Providing and fitting fixing of pressure meter ( 0.0 - 14.0 Kg/ sqcm.) as per specification and as per specification and the direction of the Engineer - in-charge. |
| 750 | Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner. |
| 751 | Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.(b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(d) Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 lpm at 70 m Head, |
| 752 | (a) Supplying, installation, testing and commissioning of diesel engine driven main fire pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump)(b) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal as required.(c) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding,residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.(d) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads.2280 lpm at 70 m Head, |
| 753 | Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.180 lpm at 70 m Head, |
| 754 | Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. |
| 755 | Dewatering pump: Supplying, installation, testing and commissioning of auto on/off Drainage Submersible Pump (2 no's) (DPK.10.50.075.5.0D) suitable for single phase, 230 volts AC supply including connection of suction and delivery line etc. , (Q= 14 cum/hr., Head = 10m), including of control panel 2P 3PH 8A auto GIDPC auto on/off, complete as required in all respect as per technical specification and as per direction of Engineer. |
| 756 | Supply, Installation, Testing & commissioning of factory assembled of fuel tank, 220 ltrs, battery charger panel - 12V including all necessaries accessories complete as per technical specification and as per direction of Engineer. |
| 757 | Supplying, installation, testing and commissioning of following ratings Valve regulated lead acid(VRLA) battery with all accessories including necessary connections etc. as required:-12 V/ 180AH tall tubular/ flat plate Battery:- |
| 758 | Supply, Installation, Testing & commissioning of control Fire Panel: Including auto / Manual Operation Considered, Individual Pressure Switch is and pressure transmitter considered for each Pump, Potential Free Contacts for On / Off and Trip of each Pump Considered for BMS, Indoor / Basement Mounted Enclosure Considered, Cable Bottom Entry Considered, One Voltmeter and Individual Ammeter considered and MCCB considered at incomer etc. complete as per technical specification and as per direction of Engineer. |
| 759 | Supply, Installation, Testing & commissioning of Cable with level switch 10m length complete as per technical specification and as per direction of Engineer. |
| 760 | Supply, installation, testing & commissioning Battery for Fire Panel and as per direction of Engineer. |
| 761 | Terrace (booster) PumpsSupplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head |
| 762 | Supply, installation, testing and commissioning of cubicle type wall/ floor mounted power cum control panel made out of not less than 1.6 mm thick MS sheet and comprising of following panel mounting switchgears there in including connection inter-connection etc. as required.a) Phase indicating lamps with fuses and toggle switches 1 set b) Star-delta starter suitable for 7.5 HP 3 phase AC induction motor with over load and no volt relay c) 32 A \\"C\\" series TPMCB 1 No d) Voltmeter 0-500 V with selector switch 1 sete) Ammeter 0-10 A with CT's and selector switch 1 set. |
| 763 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :100 mm dia |
| 764 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100 mm dia |
| 765 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :100 mm dia |
| 766 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : - 25 mm nominal bore |
| 767 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. |
| 768 | Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner. |
| 769 | Terrace TankCentering shuttering including struttings, propping etc. and removal of form work for:Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply (For retaining wall) |
| 770 | Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 771 | Lintels, beams, plinth beams, girders, bressumers andcantilevers with shuttering ply |
| 772 | Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 773 | Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete as required as per direction of the Engineer-in-charge:Serrated with central bulb (225 mm wide, 8-11 mm thick) |
| 774 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification |
| 775 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 776 | Supplying and fixing C.I. cover without frame for manholes :455 x 610 mm rectangular C.I. cover (light duty)the weight of the cover to be not less than 23 kg. |
| 777 | Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 :Upto 300 mm dia. |
| 778 | Fire ExtinguisherSupply & Fixing ISI marked (IS:13849) Portable Fire Exitnguisher, ABC type capacity 5 kg, finished externally with red enamel paint, complete in all respects including initial fill and wall suspension. Capacity 5 kg |
| 779 | Supply & Fixing ISI marked (IS:2878) Portable fire Extinguisher, Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia. min. 600 mm long & complete in all respects including initial fill with C02 gas confirming to IS:307-1966 filled to a filling ratio of not more than 0.667 and wall suspension bracket.Capacity 4.5 Kg |
| 780 | Supply & Fixing ISI marked (IS:10204) Poratable Fire Exitnguisher,Trolley mounted Mech. Foam type capacity 09 ltrs with gun-metal cap and nozzle and complete respects in all respects including initial fill and wall suspension. Capacity 9.0 ltrs |
| 781 | Supply & Fixing of ISI marked (IS:2878) Fire Extinguisher, Trolley mounted, CO2 (gas pressure) type capacity 22.5 Kg. with gun-metal cap. And nozzle and complete in all respects including initial fill and wall suspension bracket. Capacity 22.5 Kg |
| 782 | Fire AlarmAuomatic fire alarm system/ operated electronic fire alarmSupplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to rintout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications.Two Loop Panel. |
| 783 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. (Manual Break Glass ) |
| 784 | Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required. |
| 785 | Supplying, installation, testing & commissioning of fault isolator complete with base as required. |
| 786 | Supplying, installation, testing & commissioning of addressable fire control module complete as required. |
| 787 | Supplying, installation, testing & commissioning of Repeater panel with 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence swithes complete as required. |
| 788 | Supplying, installation, testing & commissioning talk back slavestation in surface/recess suitable for operation on simplexmode complete with P.T.T. knob & speaker/microphoneenclosed in a M.S.(16 SWG)/ ABS box with break glass in frontetc. complete as required. |
| 789 | Supplying, installation, testing & commissioning of heat detector oprating at 54 °C/57 °C with rate of rise cum fixed tempreture (dual thermistor) type with mounting base complete with all conection etc. as required. |
| 790 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. (Analog addressable Hooter for alarm/evacuation signal) |
| 791 | Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. |
| 792 | Supplying, installation, testing & commissioning of intelligentanalog addressable photothermal detector complete withmounting base complete as required. |
| 793 | Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required. |
| 794 | Providing and fixing FRLS Armoured Cable from individual flow switches on each floor to annunciation panel installed in fire control room in basement including sleeves, cable clips, supports for horizontal runs making connection to each switch complete.4 core 2.5 Sqmm |
| 795 | Supply, installation, testing and commissioning of Gong Bell Unit with tapping, pipes, Valves, interconnecting hoses and pipings complete as required to make it operational. |
| 796 | Supply, installation, testing & commissioning of UPS (1 KVA) with two-hour Power Backup and other required accessories. |
| 797 | Supplying, installation, testing & commissioning of SITC of UL listed and FM approved Intelligent adressable class X type (style 7) input output module with polarity-insensitive technology and in-built dual isolator, tri-color LED for status (Green for normal, Yellow for faulty & Red for activation). Integral single-pole, double-throw (SPDT) relay on Model HTRI-R (up to 4 amps). Two wire operation and dynamic supervision complete with base as required. |
| 798 | Supplying, installation, testing & commissioning of SITC of UL38 listed, ROHS compliant & FM approved Intelligent adddressable class X (Style 7) Single Action Manual Pull Station. The MCP should be polarity-insensitive and have multi-color status LED. The MCP have in-built isolator for better reliability, circuit integrity and advance fault finding complete with base as required. |
| 799 | Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5 % V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications.Two loop Panel |
| 800 | Provisional Sums Statutory payments to water resources, National Highways, State Highways, Indian Railways, Forest Department, Archaeological Survey of India and similar organizations, Provision towards costs associated with social safeguards, Network expansions if required beyond the present scope, Nalla crossings, any dismantling work, shifting of utilities and miscellaneous works.NOTE:It is a non-competitive amount and bidder should enter the sum INR 1,01,25,155.49 (One Crore One Lakh Twenty Five Thousand One Hundred Fifty Five and Fourty None Paisa only) without any alteration.Any other figure quoted in price bid will be ignored. The competent authority reserves the right to reject financial bids if provisional sum quoted is beyond the amount specified above. |
| 801 | A. Implementation Staff |
| 802 | Occupational Health & Safety and Environment Officer cum Social & Community Liaison Officer |
| 803 | B. Statutory Compliance & Clearances |
| 804 | Consent to Establish (CTE) & Operate (CTO) |
| 805 | Groundwater extraction permission |
| 806 | Tree cutting permission & compensatory plantation |
| 807 | Labour licenses & statutory permits |
| 808 | C. Mitigation Measures – Construction PhaseC2.Waste Management |
| 809 | Municipal solid waste management (site & camp) |
| 810 | Hazardous waste storage & disposal |
| 811 | C5. Health & Safety |
| 812 | First aid facilities & medical support |
| 813 | Worker health & safety (incl. disease prevention) |
| 814 | D. Monitoring MeasuresPre construction and Construction Phase |
| 815 | Air quality monitoring |
| 816 | Noise level monitoring |
| 817 | Surface water monitoring |
| 818 | Groundwater monitoring |
| 819 | Soil quality monitoring |
| 820 | Mitigation Measures – Operation Phase |
| 821 | Air quality monitoring |
| 822 | Noise level monitoring |
| 823 | Surface water monitoring |
| 824 | Treated wastewater (STP) |
| 825 | Groundwater monitoring |
| 826 | Plantation survival monitoring |
| 827 | Capacity Building & Training |
| 828 | Worker induction & safety training |
| 829 | Refresher training & mock drills Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 27 daysNov 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 27 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender