Tender For Development Of Konark Urban Haat, Puri
Tender Value
3.44 Crore
Estimated cost
Bid Submission
28 Oct 2026
4 days left
EMD
3.44 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Puri → Odisha
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Development Of Konark Urban Haat, Puri
BOQ
| Sl. No. | Item Description |
| 1 | Horticulture & Landscape Development |
| 2 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water |
| 3 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete |
| 4 | Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete |
| 5 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete |
| 6 | Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly, as per direction of officer in charge |
| 7 | Preparation of mounds of various size and shape by available excavated /supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. |
| 8 | Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m: |
| 9 | Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge. |
| 10 | Providing and Displaying Ficus Nuda topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180to 210cm ht in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 11 | Providing and Displaying Foxtail palm well developed with fresh & healthy foliage of ht. 210 to 240 cm in big 40 cm Cement Pot as per direction of the officer-in-charge. |
| 12 | Site Levelling & Filling for Urban Haat, Konark |
| 13 | Filling at all depth with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 15 cm in depth : consolidating each deposited layer by ramming and watering complete (lead upto 100m) as directed by the Engineer-In-charge. |
| 14 | Supplying of filling sand in foundation and over areas including watering, ramming, consolidating and dressing, labours, tools, taxes etc. all complete as per the specification and direction of Engineer-In-charge. |
| 15 | External Pathway |
| 16 | Providing and laying natural cobblestone flooring of approved size typically 100 x 100 x 50-80mm or as specified , colour & texture over a prepared 25-40mm thick cement mortar bed (1:4) on a compacted CC sub-base (1:3:6). Stone shall be hand dressed , laid in the required pattern with uniform joints of 8-15mm , jointed with cement mortar or polymeric jointing compound , compacted , levelled, and finished to the required line , level & slope including all materials , labour complete as per drawing. |
| 17 | Free Standing Site Signages |
| 18 | Free Standing Site Signages(2' x 3'): Providing & fixing signage made from machine cut natural laterite stone , dressed on all exposed faces with smooth / Chisel finish as specified. The stone shall be securely fixed on a reinforced concrete pedestal/ foundation using stainless steel anchor bolts, dowels , epoxy adhesive and non shrink grout finished with Granite top as required. The signage shall include 3mm thick Grade 304 stainless steel laser cut letters / logo with stain finish fixed to the stone using concealed stainless steel studs and epoxy adhesive. all the edges shall be smooth including all material , labour etc complete in all respect as per approved sample by Architect. |
| 19 | Outdoor Furniture |
| 20 | 4- seater Cafe table as per Sample approved by Architect |
| 21 | Café Outdoor Chair as per Sample approved by Architect |
| 22 | Stall |
| 23 | FLEA stall including Base foundation : 10 ft × 10 ft modular pagoda with heavy-duty MS/GI frame, waterproof PVC canopy, full-colour custom printed branding, reusable foldable structure, suitable for exhibitions and flea markets as per direction of Architect |
| 24 | Food stall including Base foundation: 10 ft × 10 ft custom fabricated food /kiosk with MS frame, ACP exterior cladding, serving counter, storage cabinets, electrical provisions, waterproof roofing, custom branding & graphics, ready for food vending operations as per direction of Architect |
| 25 | Sculpture |
| 26 | Providing, carving, supplying, transporting and installing Sculpture (5' ht) made from approved quality khandolite Stone of approved size, shape & design, as per approved drawing by the Architect. The work shall include sound, crack-free stone blocks, rough dessing, fine hand / mechanical carving, profiling and finishing to achieve the approved artistic details. The sculpture shall be mounted on a suitable foundation/ pedestal using stainless steel dowels, anchor bolts and necessay accessories. The exposed stone surface shall be finely finished & cleaned with edges neatly dressed including all labour, materials complete in all respect as per guidance of the Architect. |
| 27 | Providing, carving, supplying, transporting and installing Sculpture (4' ht) made from approved quality khandolite Stone of approved size, shape & design, as per approved drawing by the Architect. The work shall include sound, crack-free stone blocks, rough dessing, fine hand / mechanical carving, profiling and finishing to achieve the approved artistic details. The sculpture shall be mounted on a suitable foundation/ pedestal using stainless steel dowels, anchor bolts and necessay accessories. The exposed stone surface shall be finely finished & cleaned with edges neatly dressed including all labour, materials complete in all respect as per guidance of the Architect. |
| 28 | Providing, carving, supplying, transporting and installing Sculpture (15' ht) made from approved quality khandolite Stone of approved size, shape & design, as per approved drawing by the Architect. The work shall include sound, crack-free stone blocks, rough dessing, fine hand / mechanical carving, profiling and finishing to achieve the approved artistic details. The sculpture shall be mounted on a suitable foundation/ pedestal using stainless steel dowels, anchor bolts and necessay accessories. The exposed stone surface shall be finely finished & cleaned with edges neatly dressed including all labour, materials complete in all respect as per guidance of the Architect. |
| 29 | Art & Craft Workshop (5 nos of Pindi) |
| 30 | Providing and laying plain cement concrete of proportion (1:3:6) in foundation and floors using 4 cm. size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality and from approved quarry including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm. thick in each layer including cost, conveyance, royalties and cost of all labours,labour cess, T&P etc complete as per specification & direction of the Engineer-in-charge. |
| 31 | First class Fly ash Brick masonry using bricks of size 25cm. x 12 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix( 1:6) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar after immersing the bricks for 6 (Six) hours in water before use in Foundation & Plinth including splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as directed by the Engineer-In-Charge. |
| 32 | Fly Ash Brick Masonry in cement mortar of mix (1:6) using Fly Ash bricks of size 25c.m x 12 c.m x 8 c.m in Super structure having crushing strength not less than 75 kg per square c.m. with cement and screened & washed sharp sand for mortar after immersing the bricks for 6 (Six) hours in water before use in works with all necessary projections, splays cutting, circular moulding, corbelling, chamfering, watering and curing etc. including cost, coveyance,stacking, loading, unloading, royalties , all taxes ,cost of all labour,Labour cess ,scaffolding, sundries and T&P required for the works etc. complete in all respect as directed by the Engineer-in-charge. |
| 33 | Supplying of filling sand in foundation and over areas including watering,ramming, consolidating and dressing, labours, tools, taxes etc., all complete as per the specification and direction of Engineer-In-charge. |
| 34 | Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties, with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect and specification and direction of the Engineer in charge. |
| 35 | Providing 16mm. thick unpolished Kota stone flooring using kota stone of approved quality, colour and size above 0.10 sqm in floors, treads on steps and landing on 20mm. thick bed of cement mortar mix of (1:4) with screened and washed sharp river sand for mortar and cement of approved quality, grouted with neat white cement slurry laid in proper slope joining the Kota stone with neat white cement slurry mixed with required quantity of pigment of approved marks to match the shades of the kota stone to kota colour if required, watering and curing for the required period , including cost, conveyance, loading, unloading, royalties, and taxes of all materials, cost of all labour, sundries, T&P required for the work including cost of rubbing mechanically and wax polishing etc complete in all floors at all height in all respect as directed by the Engineer-in-charge. |
| 36 | External Pathway |
| 37 | Supplying of filling sand in foundation and over areas including watering,ramming, consolidating and dressing, labours, tools, taxes etc., all complete as per the specification and direction of Engineer-In-charge. |
| 38 | Supplying & fixing of 60mm thick cement concrete interlocking Paver block of M-30 grade of approved make design, colour & size made by block making machine with propoer compaction laid in required pattern etc. complete in all respectconfirming to IRC SP 63:2018 |
| 39 | Providing and laying plain cement concrete of proportion (1:3:6) in foundation and floors using 4 cm. size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality and from approved quarry including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm. thick in each layer including cost, conveyance, royalties and cost of all labours,labour cess, T&P etc complete as per specification & direction of the Engineer-in-charge. |
| 40 | Providing 16mm. thick unpolished Kota stone flooring using kota stone of approved quality, colour and size above 0.10 sqm in floors, treads on steps and landing on 20mm. thick bed of cement mortar mix of (1:4) with screened and washed sharp river sand for mortar and cement of approved quality, grouted with neat white cement slurry laid in proper slope joining the Kota stone with neat white cement slurry mixed with required quantity of pigment of approved marks to match the shades of the kota stone to kota colour if required, watering and curing for the required period , including cost, conveyance, loading, unloading, royalties, and taxes of all materials, cost of all labour, sundries, T&P required for the work including cost of rubbing mechanically and wax polishing etc complete in all floors at all height in all respect as directed by the Engineer-in-charge. |
| 41 | Pylon |
| 42 | Pylon (Height 15'): Providing , fabricating, supplying and installing Pylon (Height 15') signage comprising a Khandolite stone base , MS structural frame welded , treated with one coat of primer and 2-coats of SE paint. FRP cladding UV resistant , weather proof , finished in approved colour and stainless steel lettering of grade 304 complete in all respect as per drawing & design approved by Architect. |
| 43 | Pedestrian Roadscape |
| 44 | MS Pole 100 x 100 x 3mm fixed over RCC foundation at a distance of 3m side by side customized FRP cladding as shown in the design and over it Tensile fabric canopy supported by powder coated MS structure. Keeping Canopy ht 3m. Including labour, material, engineering as per guidance of the architect. |
| 45 | FRP Claddinng over pillar |
| 46 | MS Pole Tensile fabric canopy |
| 47 | LIGHT SYSTEM EXTERNAL |
| 48 | Supply, installation, testing and commissioning of LED Design based BIS approved LED Street Light with system power of 120W, CCT in 5700K as per ANSI) ,CRI>70, SDCM<3 , LEDs used should have a life of 50,000 burning hrs. & Lumen maintenance as per L70. The Luminaire System lumens should be >=19,200 Lumens @5700K. The fixture housing must be Made of ADC 12 PDC Aluminium housing for rapid thermal healing & Powder coated by Corrosion resistant Nano coating technology. Luminaire must have a Ingress protection of IP66 and Impact Resistance of IK08. The light engine should use Metal Core PCB with high grade aluminium (AL5052) and should have a thermal conductivity of >2W/mK. The fixture should have an UV stabilized Injection moulded special PC lens optics(Glass not allowed) ensuring low glare & best in class uniformity. The light and the driver compartment should be thermally isolated by a natural airgap. Luminaire housing and optical compartment both should carry OEM's logo embossed / engraved (no stickering is allowed). The luminaire must have Integral encapsulated high efficiency electronic thermally isolated driver having a Aluminium extrusion construction with rated voltage of 100-300V, power factor > 0.95, THD < 10%, with Inbuilt surge protection of min 6KV and upgraded with integrated IP67 protected SPD of 20KV/10KA surge protection with all necessary safety protection like mis-wiring, Over voltage, Short circuit, Reverse Polarity protection. . The compartment should be bottom openable for ease of maintenance at site. Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-03/05/06/07, Surge : IEC 61000-4-5, EMC : EN 55015. Following documents to be submitted after award of contract: Luminaire and Driver TDS, Photometry report, Type test certificate, IP, IK, Vibration and salt spray test certificates from NABL accredited Laboratory, LM80 from LED OEM., CE Certification, ROHS compliant, BIS Certificate for Luminaires & Drivers. The warranty on light fixture shall be 5 years. (Make: PHILIPS/WIPRO/BAJAJ/Crompton/PANASONIC/LT/HAVELLS) |
| 49 | Supply of 8 mtr long hot dip Galvanized Octagonal pole manufactured from HT steel(with decorative single arm) as per BS EN 10025/IS 2062 having minimum yield strength of 350 N/ SQMM having top dia of 70 MM A/F and bottom dia of 155 MM A/F of 3 mm thick or more , base plate as per IS 2062 complete with 4 nos. En 8 grade foundation bolts to withstand basic wind speed of 180 KM/HR wind speed (As per structural calculation of pole manufacturer )or more (Make of poles: Utkarsh/Bajaj/RR Ispat/Vakarangee as per direction of Engg. in Charge. |
| 50 | Supply of 8 mtr long hot dip Galvanized Octagonal pole manufactured from HT steel(with decorative DOUBLE arm) as per BS EN 10025/IS 2062 having minimum yield strength of 350 N/ SQMM having top dia of 70 MM A/F and bottom dia of 155 MM A/F of 3 mm thick or more , base plate as per IS 2062 complete with 4 nos. En 8 grade foundation bolts to withstand basic wind speed of 180 KM/HR wind speed (As per structural calculation of pole manufacturer )or more (Make of poles: Utkarsh/Bajaj/RR Ispat/Vakarangee as per direction of Engg. in Charge. |
| 51 | Construction of RCC foundation by using M20 grade RCC and Fe 415 grade reinforcement in the foundation by considering the SBC as 10 T per sq mtr and fixing the 4 nos. fdn bolts in that foundation for installation of pole with street light on that foundation(Details Drawing of the foundation attached). The work shall be excuted as per the direction of EIC.The structural calculation, wind load calculation and civil foundation shall be duly approved by the competent authority from civil wing (SE/CCE/Competant authority)before execution of the work. |
| 52 | Supply , Installation, Testing and commissioning of 5meter Florus Lighting Pole long aesthetically Trishul Design on top and shankh/chakra design on arm designed single Arm decorative lighting pole supplied with -3000K-Type II-Polycarbonate Optical Lens 100W LED decorative light having 80Lm/W Lumen output and made up of Spun Aluminium body & Milky acrylic (A9) diffuser 5m Lighting Pole Lighting Pole Height (in mm): 5000mm Pole Size: Ø76.1 PoleType: Pole shall be made up of Mild Steel Body and coated with zinc rich primer & pure polyester powder coating of Black Finish. Base Plate size of Ø230x12mm thick with provision for founation bolt. Pole is Compatible for Ø70mm size for cable entry & exist. Junction Box service door is made up cast aluminium and the control gear tray only is prewired with 2.5sq mm cable, 6A SP MCB and 32A 4pole terminal connector for loop-in loo-out arrangement with all materials & labour as required as per the direction of Engineer-3000K-100W LED Milky Acrylic Diffuser : Sq.445 x 713mmc Black Powder Coating-RAL 9004 Black-3 Years.(MAKE: klite( Pelican fort+ KP-12016 Bishop Lighting Pole )/Philips/Reytek/Homdec/Jaquar) |
| 53 | Supply , Installation, testing & commissioning of 24W LED Vista Bollard light of Dimension: Ø250 x 900mm having Spun Aluminium with Extruded Aluminium Tube(Grade 6063) housing and coated with zinc rich primer & pure polyester powder coating of Antique Copper Finish, UV Stabilized Translucent Polycarbonate diffuser. Bollard should be Customized Bespoke CNC cutting design with CCT-3000K, CRI-≥80, IP-65, IK-08, SDCM≤ 3, Lumen maintainance >60,000 burning hours as per L70 B10, Power Factor : >0.9, THD : <10%, Surge Protection : Inbuilt 4KV, Efficiency : >80%, Optical Distribution : Symmetrical. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66/65 protection and other parameters as required by the Engineer-in- Charge. (Make: K -lite Vista Bollard 24572 or, , similar to Jaquar/Bajaj/Reytek/Homdec). |
| 54 | Installation of Bollard Light by making the suitable size foundationwith necessary civil work and fixing the bollard light equievalant make ISI marked as approved as per direction of Engg. in Charge. |
| 55 | FOCUS LIGHT |
| 56 | Supply , Installation, testing & commissioning of 60W LED Focus Light having die-cast aluminium housing and coated with zinc rich primer & pure polyester powder coating of Jet Black Finish, UV Stabilized Clear toughened glass diffuser. CCT-3000K, CRI-≥70, IP-65, IK-06, SDCM≤ 3, Lumen maintainance >60,000 burning hours as per L70 B10, Power Factor : >0.95, THD : <10%, Surge Protection : Inbuilt 4 KV, Efficiency : >80%, Optical Distribution :45 degree beam angle. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66 protection and other parameters as required by the Engineer-in- Charge. (Make: K -lite Iyra KL-22561 Luminaries or, similar to Jaquar/Bajaj/Reytek/Homdec). |
| 57 | Supply , Installation, testing & commissioning of 36W LED Linear wall washer Light of dimenssion must be 1000X85X38 having 6063 Aluminium Alloy housing with UV Stabilized Clear toughened glass diffuser. CCT-3000K, CRI-≥70, IP-66, IK-05, Lumen maintainance >50,000 burning hours as per L70 B10, Optical Distribution :12 degree beam angle. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66 protection and other parameters as required by the Engineer-in- Charge. (Make: K -lite KL-23068 Luminaries or, similar to Jaquar/Bajaj/Reytek/Homdec). |
| 58 | Supply , Installation, testing & commissioning of 12W LED step light of Dimension : 255mm x 87mm x 76mm and having die-cast aluminium housing and coated with zinc rich primer & pure polyester powder coating of Jet Black Finish, UV Stabilized Satin Acrylic diffuser. CCT-3000K, CRI-≥70, IP-65, IK-09, SDCM≤ 3, Lumen maintainance >60,000 burning hours as per L70 B10, Power Factor : >0.95, THD : <10%, Surge Protection : Inbuilt 6KV, Efficiency : >85%, Optical Distribution :120degree. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66 protection and other parameters as required by the Engineer-in- Charge. (Make: K -lite Sudo KL-22525 Luminaries or, similar to Jaquar/Bajaj/Reytek/Homdec). |
| 59 | Solar light |
| 60 | Supply of Elegant look 60 W AIO LED Solar Street lights having extruded alluminium housing, 180Wp or more (subjected to final panel backup calculation with dimming profile of 100% output for 2 hrs, 90% output for 1 hr, 60% output for 1 hr and 50% output for 8 hrs per day. The calculation is to approved by SE,Electrical Circle (R&B) and CE ,Buildings, Odisha, BBSR before final procurement of the product.) Mono Crystalline Panel/Laminates fixed on the top of the luminaire housing, maintenance free 12.8 volts 78 Ah or more (subjected to final battery calculation with dimming profile of 100% output for 2 hrs, 90% output for 1 hr, 60% output for 1 hr and 50% output for 8 hrs per day. The calculation is to approved by SE,Electrical Circle (R&B) and CE ,Buildings, Odisha, BBSR before final procurement of the product.) LiFePO4 battery(BIS certified) , BMS, MPPT charge controller, PIR sensor( when there will be no movement the lumens output will be 30% output).The solar panel and battery should be designed to provide 2 days (24 hrs ) back up . The luminaire is having IP 65 protection for critical components, IK 08 and having lumen output of >=10000 lumens as per LM 79 report third party/central/state govt accredited NABL lab to justify the lumen output & lumen efficacy . Lenses should be provided on the LED chip for better lighting dstribution to avoid glare on human eyes. Both the luminaire and Mono Crystalline Panel must be manufactured in India. The Solar lighting company must submit the third party central/state govt accredited NABL lab reports to justify the lumen efficacy,luminaire output , IK 08 and IP 65 protection.The Luminaire should be supplied along with adjustable type mounting bracket which can be fitted directly on the pole.The Solar lighting manufacturer must submit the declaration letter by mentioning that complete solar light and the solar panel are manufactured in India and warranty certificate on their company's letterhead by mentioning warranty period as 5 years and necessary aftersales Service will be provided through their tollfree base service network located within 100 KM from the project site. The Solar Street light manufacturer should have own NABL accredieted laborotory. The following test reports must be submitted and approved from SE,Electrical Circle (R&B) and CE ,Buildings, Odisha, BBSR for the technical acceptance of the products.1.LM 79 REPORT and LM 80 Report ( from third party/central/state govt accredited NABL lab of AIO solar light) , 2. IK 08 ( from third party/central/state govt accredited NABL lab of AIO solar light ) , 3. IP 65 (Report of third party/central/state govt accredited NABL lab of AIO solar light 4. EN50530 – MPPT Efficiency , 5. IEC61547 , 6. IEC61000-3-2 – EMC , 7. IEC 60598-2-3 ,8. IEC 62109-1, ( The necessary test reports of third party/central/state govt accredited NABL lab from sl no. 4 to sl no.8 must be submitted for any wattage of AIO solar light )Make-(Philips/Panasonic/Wipro/Crompton/Bajaj/Havells/LT ). NB: The cost includes 5 years CMC including repair/ Maintenance/ replacement of the product in case of any defect. |
| 61 | Supply of 8 mtr long hot dip Galvanized Octagonal pole manufactured from HT steel as per BS EN 10025/IS 2062 having minimum yield strength of 350 N/ SQMM having top dia of 70 MM A/F and bottom dia of 155 MM A/F of 4 mm thick or more , base plate as per IS 2062 complete with 4 nos. En 8 grade foundation bolts to withstand basic wind speed of 180 KM/HR wind speed (As per structural calculation of pole manufacturer )or more (Make of poles: Utkarsh/Bajaj/RR Ispat/Vakarangee as per direction of Engg. in Charge. |
| 62 | Installation of pole by making the suitable size foundation by embeding the pole 1 mtr into the ground with necessary civil work and fixing the light on the pole equievalant make ISI marked as approved as per direction of Engg. in Charge. |
| 63 | Installation of 60W AIO LED solar street light on 8 mtr octagonal pole. |
| 64 | HighImast lighting |
| 65 | Supply,installation,testing and commissioning of 12M mini mast shaft in two sections suitable for 55 m/sec wind speed along with head frame, luminaires carriage suitable for 6 luminaires in symmetrical arrangement and other accessories manufactured in factory. ( Bottom 360mm / Top -150mm, 3mm thickness, 445PCD, diameter of base plate 520mm including supplying of raising lowering system comprising double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightning finial. (Wiring material from JB to individual luminaire & MCB in base compartment are not included and are a part of installation)along with foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template along with Construction of shallow foundation with M20 grade concrete for the highmast considering the safe soil bearing capacity at site as 10 T/sqmtr at 2 metre depth with all materials and labour.Erection of the high mast with the help of suitable tools and plants, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 1.5 sq. mm, lugs, MCB and all labour . Provision of GI pipe earthing for High mast with 2.5 M long 40 mm dia GI Pipe including connection to High mast earth terminal with 25 x 3 mm GI flats with all materials and labour. (2nos per mast required) Approved colour after treatment along with provision of masonary pedestal duly finished with plaster and painting with GI pipe for cable entering as required.. (2nos per mast required) (Make:-Bajaj/ Utkarsh/ Vakrangee/RR ISPAT/Valmont |
| 66 | SITC of 2150W Outdoor Flood LED lights with silicon potted driver, IP66, , bottom opening maintanance , LPW not less than 130.Input Voltage: 85-265V AC ,Body : Die cast Aluminium, IP66 as per the Drawing for inspection as required & as per direction of Engg.-in-Charge. Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj as rerquired. |
| 67 | LED type single dome aviation obstruction light. (Make:-Bajaj/ Utkarsh/ Vakrangee/RR ISPAT |
| 68 | S/I/T&Commissioning of LT OUT DOOR FLOOR mounted cubical type IP66 based panel made out by 2mm CRCA steel sheet duly derusted & pented by simens gray powder cote paint is designed as G.A drawing. (FOR USE) with 63A TPN MCB 01 NO,1 no. Astronomical digital timer, AUTO MANUAL(with start and stop push button) SELECTOR 63 A 3P contactor, OLR,RYB,ON,OFF trip indication, Type-II SPD 40ka ,,04 nos 10A 4P MCB,C,10KA as outgoing MCB( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period 1 years of acceptance of materials Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender