Tender For Development Of Existing Infrastructure At Urban Haat, Konark In Puri District
Tender Value
3.96 Crore
Estimated cost
Bid Submission
28 Oct 2026
14 days left
EMD
3.96 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Puri → Odisha
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Development Of Existing Infrastructure At Urban Haat, Konark In Puri District
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in ordinary soil with initial lead and lift including rough dressing in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles as directed by the Engineer-in-charge. |
| 2 | Earthwork in excavation in all types of soil for site leveling, foundation, pits, trenches and other civil works up to and including 1.5 metre lift and stacking the soil upto a lead of 100 metre and including dewatering, removing slush, shoring and strutting (as required), complete as per specification and as directed by the Engineer-In-Charge. (Septic tank & Soak pit) |
| 3 | Upto 1.5M Depth |
| 4 | From 1.5M Upto 3.0M Depth |
| 5 | Sub grade filing with Earth |
| 6 | Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision) |
| 7 | Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. |
| 8 | Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing. |
| 9 | Providing and constructing Laterite stone kerb wall (typically 230 mm thick and height as specified) using approved quality, hard, dense, and durable laterite stones, free from cracks, cavities, weathered portions, and other defects. Stones shall be machine cut or hand dressed to regular dimensions with true beds and vertical joints. The kerb wall shall be of the dimensions shown in the drawings and shall be laid in cement mortar 1:6 (1 cement : 6 coarse sand). |
| 10 | Providing and laying plain cement concrete of proportion (1:3:6) in foundation and floors using 4 cm. size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality and from approved quarry including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm. thick in each layer including cost, conveyance, royalties and cost of all labours,labour cess, T&P etc complete as per specification & direction of the Engineer-in-charge. |
| 11 | Providing and lying plain cement concrete of proportion (1:4:8) in foundation and floors using Portland slag cement (PSC) with 40 mm. Size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes all materials and cost all labours, sundries, T & P required for the work including shoring, shuttering and dewatering if required including hire & running charges of water pump complete as per the instruction of the Engineer-in-Charge. (Drain) |
| 12 | Supplying of filling sand in foundation and over areas including watering, ramming, consolidating and dressing, labours, tools, taxes etc. all complete as per the specification and direction of Engineer-In-Charge. |
| 13 | Septic tank |
| 14 | Filling at all depth with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 15cm in depth : consolidating each deposited layer by ramming and watering complete (lead upto 100m) as directed by the Engineer-In-charge. |
| 15 | Septic tank, Soak pit & Drain |
| 16 | Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position. |
| 17 | Base (for below ground level beyond 1.5m and upto 4.5m depth) (Septic tank) |
| 18 | Wall (Septic tank) |
| 19 | Slab (Septic tank & Soak pit) |
| 20 | Supplying, straightening, cutting, bending, placing in position and binding reinforcement steel work in RCC/reinforced brick works as per drawing and specification including preparation of respective bar bending schedule and binding (Binding wire to be used as per the IS code) etc. all complete as per direction of Engineer-In-Charge.Cold Twisted bars, Thermo-Mechanically-treated bars. |
| 21 | Septic tank & Soak pit |
| 22 | Brick work with Fly Ash. Bricks in cement mortar (1:6) in Super Structure having crushing strength not less than 75.00 kg/cm2 immerging the bricks in water not less than six hours before use in masonary. |
| 23 | For below ground level beyond 1.5m. and upto 4.5m. Depth in well steining foundation and plinth. |
| 24 | For brick masonry in well steining foundation and plinth. |
| 25 | 12mm thick cement plaster (1:4) over brick work with cost of all materials and all labour etc. (with punning skirting) |
| 26 | Septic tank & Rechrge pit |
| 27 | Supplying all materials, labour, T&P and providing cement punning including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 28 | for below ground level beyond 1.5m and upto 4.5m depth) Recharge pit |
| 29 | Below ground level upto 1.50m |
| 30 | Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for R.C.C works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge |
| 31 | R.C.C floor and roof slabs (Recharge pit ) |
| 32 | Supplying all materials, labour, T&P and providing M.S reinforcement for R.C.C work including cutting, bending, binding, and tying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge (Ground floor) (Recharge pit) |
| 33 | Supplying and Fixing of M.S. Grill made out of M.S Flat conforming to IS 2062/2006 excluding the cost of Red Oxide Primer as per the design approve by E.I.C including cost,conveyance of all materials,priming,and labour for fitting fixing etc.complete as per the instruction of Engineer-in-Charge |
| 34 | Painting two coat with approved synthetic enamel paint over a coat of Red oxide primer to new wood & iron work including cost, conveyances, royalties of all materials and cost of all labour with T&P required for the work etc. complete as per specification & direction of Engineer in charge. |
| 35 | Providing and laying approved quality hard, compact, machine-dressed Laterite stone coping/band of size 300 mm wide × 75 mm thick (or as shown in the drawings), free from cracks, cavities, and weathered portions. The stone shall be neatly dressed with true edges and smooth exposed surfaces. The coping shall be laid over the top of the boundary wall in 1:4 cement mortar (1 cement : 4 coarse sand) with an average 20 mm thick bedding. Joints shall not exceed 10 mm in width and shall be fully filled with cement mortar. The coping shall be provided with a 25 mm wide × 25 mm deep drip groove on both exposed sides, approximately 40 mm from the edge, to prevent rainwater from flowing down the wall face. The top surface shall be finished with a slight slope towards both sides for proper drainage. All exposed edges shall be chamfered 10 mm × 10 mm unless otherwise specified. The work shall include curing for not less than 7 days, all cutting, dressing, lifting, placing, scaffolding, labour, tools, and all incidental works complete as directed by the Engineer-in-Charge. |
| 36 | Providing and painting a coat of water based primer of approved quality and approved shade in all floors at all height by making the surface of wall smooth including cost, coveyance, loading and unloading and taxes of all materials, cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by the Engineer in charge. |
| 37 | Ground floor |
| 38 | First floor |
| 39 | Wall painting two coats with Weather coat paint (1st quality) exterior grade of approved make & with an approved quality primer to make an even finished surface in all floors and heights with all scaffolding and staging charges including cost, conveyance, cost of all labours, T & P, sundries etc. as required for the work complete in all respect as per the direction of the Engineer-in-Charge. |
| 40 | Ground floor |
| 41 | First floor |
| 42 | Fly Ash Brick Masonry in cement mortar of mix (1:6) using Fly Ash bricks of size 25c.m x 12 c.m x 8 c.m in Super structure having crushing strength not less than 75 kg per square c.m. with cement and screened & washed sharp sand for mortar after immersing the bricks for 6 (Six) hours in water before use in works with all necessary projections, splays cutting, circular moulding, corbelling, chamfering, watering and curing etc. including cost, coveyance,stacking, loading, unloading, royalties , all taxes ,cost of all labour,Labour cess ,scaffolding, sundries and T&P required for the works etc. complete in all respect as directed by the Engineer-in-charge. |
| 43 | Ground floor |
| 44 | Fly Ash Brick Masonry in cement mortar of mix (1:4) using Fly Ash bricks of size 25c.m x 12 c.m x 8 c.m in Superstructure having crushing strength not less than 75 kg per square c.m. with cement and screened & washed sharp sand for mortar after immersing the bricks for 6 (Six) hours in water before use in works with all necessary projections, splays cutting, circular moulding, corbelling, chamfering, watering and curing etc. including cost, coveyance,stacking, loading, unloading, royalties ,all taxes ,cost of all labour,Labour cess ,scaffolding, sundries and T&P required for the works etc. complete in all respect as directed by the Engineer-in-charge. |
| 45 | First floor |
| 46 | Supply, fabrication of cast iron railing to be fixed on Concrete pedestal/foundation finished with Anti rust Primer & painted with 2 coats Enamel paint(Exterior grade) as per the design approve by Architect including cost, conveyance of all materials, priming and labour for fitting fixing etc.complete as per the instruction of Engineer-in-Charge |
| 47 | Seating bench with back rest made of Khandolite stone: Providing, fabricating, and fixing Khandolite stone seating bench of approved quality using hard, dense, sound, and durable Khandolite stone, free from cracks, cavities, laminations, weathered portions, and other defects. The stone shall be machine cut and finely dressed to the dimensions shown in the approved drawings. The seat slab shall be securely fixed over the stone supports using stainless steel dowels (12 mm diameter, Grade SS 304) embedded at least 75 mm into both the seat slab and supports with approved non-shrink epoxy grout or polymer-based anchoring adhesive. Where required, the supports shall be fixed to a reinforced cement concrete (RCC) foundation/pedestal using stainless steel anchor bolts. (Overall bench length: 1200 mm , Seat width: 450 mm , Seat thickness: 75 mmSeat height above finished ground level: 450 mm) |
| 48 | Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties, with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect and specification and direction of the Engineer in charge. |
| 49 | Ground floor |
| 50 | First floor |
| 51 | Providing 16mm. Thick cement plaster in cement mortar or mix(1:6) in all floors at all height with cement & screened and washed sharp river sand for mortar and finished smooth to the rough surface of the brick masonary walls after racking out the joints (alongwith providing grooves wherever necessary)including watering and curing, rounding of corners etc. complete with cost,conveyance,loading, unloading, royalities and taxes of all materials,cost of all labour,T&P and scaffolding required for the work etc. as directed by the Engineer-in-charge. |
| 52 | Ground floor |
| 53 | First floor |
| 54 | Painting two coats with plastic emulsion paint in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess, T&P etc. complete as per the direction of the Engineer-in-charge. |
| 55 | Ground floor |
| 56 | First floor |
| 57 | Providing Mat finished Granite stone prepolished 20mm thick of area above 0.40 Sqm in flooring of approved quality, colour and size in floors, treads on steps and landings in all floors at all height on 20mm thick bed of cement mortar of mix (1:4) laid in proper slope and gradient with screened and washed sharp sand for mortar and fixing with neat white cement slurry,grouting the joints with neat white cement slurry mixed with required quantities of pigments of approved make to match the shades of the granite tile if required watering and curing for 21 days, including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, Labour cess ,sundries, T&P required for the work etc. complete in all respect as per specification and direction of Engineer-in-charge. |
| 58 | Ground floor |
| 59 | First Floor |
| 60 | Granite nosing: Providing and fixing Granite Nosing to staircase steps using approved quality natural granite of uniform colour and texture, hard, dense, durable, and free from cracks, veins, cavities and other defects. The granite nosing shall be 20 mm thick (unless otherwise specified). The nosing shall be fixed over the prepared RCC or masonry stair tread using 20 mm thick cement mortar (1:4) or approved polymer-modified tile/stone adhesive, ensuring full bedding without voids. The base shall be cleaned, wetted, and prepared before fixing. The work shall include all materials & labour etc all complete as per direction of EIC. |
| 61 | Providing 16mm. thick Polished Kota stone flooring using kota stone of approved quality, colour and size above 0.10 sqm in floors, treads on steps and landing on 20mm. thick bed of cement mortar mix of (1:4) with screened and washed sharp river sand for mortar and cement of approved quality, grouted with neat white cement slurry laid in proper slope joining the Kota stone with neat white cement slurry mixed with required quantity of pigment of approved marks to match the shades of the kota stone to kota colour if required, watering and curing for the required period , including cost, conveyance, loading, unloading, royalties, and taxes of all materials, cost of all labour, sundries, T&P required for the work including cost of rubbing mechanically and wax polishing etc complete in all floors at all height in all respect as directed by the Engineer-in-charge. |
| 62 | Ground floor |
| 63 | First floor |
| 64 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat (Graphite grey colour) comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. ( Frame size 62 x 100 mm) (Make: Century /Floresta/ ALSTONE) |
| 65 | Providing and fixing factory made single extruded 30 mm thick WPC solid decorative type Flush door shutter with paint finish of required size comprising of virgin polymer of K value 58-60calcium carbonate and natural fibers and non-toxic additives having minimum density of 650kg/cum and screw withdrawl strength of 1800N (FACE) & 900N (Edge) minimum compressive strength 50 N / MM2,modulus of elasticity 850N/mm2, and resistance to spread of flame of class A Category with property of being termite/borer proof , water / moisture proof and fire retandant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melted adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screw,SS Handle, Door stopper, SS Hinges, Sliding door bolt etc. all as per direction of EIC. (Make: Century /Floresta/ ALSTONE) |
| 66 | Supplying, fitting & fixing of two track UPVC sliding window of approved make with 6mm thick glass of approved quality complete with frame, shutter and all fitting & fixtures. |
| 67 | Providing and fixing UPVC framed Ventilator with frosted glass panels including all necessary hardwares and accessories and materials like handle lock etc. as per the Architect. |
| 68 | 20 cm to 25 cm Long double Nuria tiles roofing with cement motar (1:6) bprders 23cm x 5cm at 1.8meters intervals complete per 1 sqm |
| 69 | Ground floor |
| 70 | Dismantling and removing old tiled flooring including removing the base coarse and stacking the useful materials for reuse and removing the debris within 50m lead. |
| 71 | Ground Floor |
| 72 | First floor |
| 73 | Dismantling and removing old tiled cladding from walls including racking out joints 12mm deep and stacking the useful materials for reuse and removing the debris within 50m lead. |
| 74 | Dismantling & removing doors,window & ventilators including removal of frame ,hinges ,fastening & stacking the same for reuse & removing the debris within 50m lead. |
| 75 | Dismantling pan or single Nuria or Mangalore tile roofing (Tiles only) including stacking the useful materials for reuse and removing the debris within 50m lead. |
| 76 | Fixing Ceramic tile of size 30cm x 30cm in floors treads or steps and landing on 25mm thick bed of cement mortar 1:1 (1 cement : 1 sand) jointed with neat cement slurry mixed with pigment to match the shades on the tiles etc. complete. |
| 77 | Ground floor |
| 78 | First floor |
| 79 | Fixing Ceramic tiles in dados (300 x 450) skirting and risers of step on 12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing complete. |
| 80 | Ground Floor |
| 81 | First floor |
| 82 | Supplying,Fitting and Fixing vitrified tile in floors of size 600mmX600mm of approved make confirming to IS:13755 laid on 20mm thick cement mortar(1:4)(1 cement :4 course sand) and filling joints with white cement of approved quality including cost of all materials,labour, T & P etc required for the work all complete as per direction of Engineer-in-charge. |
| 83 | Ground floor |
| 84 | Toilet water proofingStage 1: Cleaning of concrete surface to remove dust, oil, grease including removal of laitance and cleaning with compressed air. Repairing surface irregularities, damaged concrete, if any, with Sika Latex modified repair mortar including a coat of bonding agent. Stage 2: Supply and application of 1:3 cement – sand mortar, mixed with SikaTop 77 – the polymer modified high quality emulsion, as a coving at the corners of floor and the vertical surface in the sunken area, and between floor and walls in the remaining area.Stage 3: Supply and application of SikaTop Seal 107 – the cementitious, flexible waterproof coating onto the prepared surface in a continuous film on the floor of the sunken area, taking the coating over the vertical surfaces on to the floor and over the coving on to the wall (before tiling) to at least 300mm above the final finished floor level. The coating shall also be continued on to the inner surfaces of the pipe penetration holes. Two coats shall be applied.Few parameters: Chemical Base Part A: liquid polymer and additivePart B: portland cement with selected aggregate and additive, Density Fresh slurry density: ~ 2.00 kg/l at +27ºC, Layer Thickness 1.5 mm – 2.0 mm average, Water Vapour Resistance 3 g /m2 / dayMechanical / Physical Properties 3 days ~ 2 N/mm2, 28 days ~ 20 N/mm2Compressive Strength Above values at +27ºC, Tensile Strength ~ 4.56 N/mm2 after 14 days exposure (According to ASTM D 2370), Bond Strength 2.0 N/mm2 at +27ºC (failure in substrate), Elongation at Break With Sika® Fab-1, 8-10 %Stage 4: Providing & filling the gap between the PVC pipe & the Concrete by pouring Free floow non shrink SikaRepmicrocrete 4 followed by Providing Sikagard 694F(I), a moisture insensitive epoxy putty in a continuous, 10mm thick gasket around the pipes to a width of approximately 15mm.Stage 5: Providing a 15mm thick plaster on the waterproof coating by mixing an integral waterproofing compound, Plastocrete Plus @ 100gms per bag of cement etc all materials, labour, T&P, transportation, taxes complete in all respect as per direction of EIC. |
| 85 | Fixing Chequerred tile of approved size in floors on 25mm thick bed of cement mortar 1:1 (1 cement : 1 sand) jointed with neat cement slurry mixed with pigment to match the shades on the tiles etc. complete. |
| 86 | 4 cm thick grading concrete (1:2:4) on roof slabwith 12mm & downgrade size black hard granitechips for old work. |
| 87 | First floor (Exhibition building) |
| 88 | Terrace waterproofing Stage 1: Cleaning of concrete surface to remove dust, oil, grease including removal of laitance and cleaning with compressed air. Repairing surface irregularities, damaged concrete, if any, with Sika Latex modified repair mortar including a coat of bonding agent. Stage 2: Supply and application of 1:3 cement – sand mortar, mixed with SikaTop 77 – the polymer modified high quality emulsion, as a coving at the corners of floor and the vertical surface in the sunken area, and between floor and walls in the remaining area.Stage 3: Supply and application of SikaTop Seal 107 – the cementitious, flexible waterproof coating onto the prepared surface in a continuous film on the floor of the sunken area, taking the coating over the vertical surfaces on to the floor and over the coving on to the wall (before tiling) to at least 300mm above the final finished floor level. The coating shall also be continued on to the inner surfaces of the pipe penetration holes. Two coats shall be applied.Few parameters: Chemical Base Part A: liquid polymer and additivePart B: portland cement with selected aggregate and additive, Density Fresh slurry density: ~ 2.00 kg/l at +27ºC, Layer Thickness 1.5 mm – 2.0 mm average, Water Vapour Resistance 3 g /m2 / dayMechanical / Physical Properties 3 days ~ 2 N/mm2, 28 days ~ 20 N/mm2Compressive Strength Above values at +27ºC, Tensile Strength ~ 4.56 N/mm2 after 14 days exposure (According to ASTM D 2370), Bond Strength 2.0 N/mm2 at +27ºC (failure in substrate), Elongation at Break With Sika® Fab-1, 8-10 %Stage 4: Providing & filling the gap between the PVC pipe & the Concrete by pouring Free floow non shrink SikaRepmicrocrete 4 followed by Providing Sikagard 694F(I), a moisture insensitive epoxy putty in a continuous, 10mm thick gasket around the pipes to a width of approximately 15mm.Stage 5: Providing a 15mm thick plaster on the waterproof coating by mixing an integral waterproofing compound, Plastocrete Plus @ 100gms per bag of cement etc all materials, labour, T&P, transportation, taxes complete in all respect as per direction of EIC. |
| 89 | Supplying and fixing of Elastomeric membrane of 200 x 2mm size for expansion joint sealing from approved manufacturer fixing with epoxy adhesive of approved quality complete.as per direction of the Engineer-in-charge. |
| 90 | Providing and fixing Toilet cubical (Classique-Versatile model of following standard dimension which includes 600mm door size width) made up of thermosetting resign treated high pressure ,self supporting decorative compact laminates with permanently incorporate anti-bacterial agents during manufacturing. Compact board should be resistance to water immersion through permissible increase on thickness and mass <0.60% and board density >1.35kg/cm3 and fulfilled the criteria of FSC and green guard gold certification and manufactured under EN438-2&3:2005 standard. 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant ,Scratch resistant ,Weather and climatic shock resistant. Finish of compact laminates should be suede finish which includes door, pilasters and intermediate panels finished with approved texture/shades as per IS2046 and fulfilled the criteria of fire retardant under BS-476/97 and EN:438-6 and cleassification of BS1D0 standard. Pilaster to be supported with SS (grade316) adjustable foot and intermediate panels will attached to the wall with the help of approved aluminium channels and all required hardware, made up of stainless steel as per manufacturer’s specification and instruction of Engineer-in-charge like Door knob, gravity hinges,Thumb turn locksets with occupancy indicators ,coat hooks with door stoper , U channel, top rail with corner connector, adjustable foot/pedestal,Rubber noice deafening tape, screw & wall plugs. The top fitting should consist of anodized aluminium metal top rail(as per manufacturer specification) which will directly get fixed with pilaster ,Aluminium corner bend (connected with top rail ) will be use in corner of cubical in absence of brick wall, Aluminium wall fixing is used only on the wall which will hold the top rail. All screw will of 304 grade in SS with stain finish. Pilaster shoud be raised from the the floor with a clearance height upto 150 mm with the help of adjustable leg.Finish and colour of Toilet cubical should be approved under guidance of engineer-in-charge. (Make: GREENLAM or Equivalent)1.01- Toilet cubical with standard dimension of 1995mm(H)x1000mm(W)x1500mm(Depth), which includes 600mm door size width or as per drawing. |
| 91 | Fixed Furniture |
| 92 | Providing and supplying wooden single bed of overall size 3'-0\\" × 6'-6\\" (900 × 1950 mm), made of seasoned, well-treated hardwood/quality timber, comprising supporting members, with properly jointed and mechanically fixed frame. The bed shall be provided with adequate intermediate supports/wooden slats for mattress support. All exposed wooden surfaces shall be smoothened and finished with approved quality wood preservative, stain and melamine/PU polish of approved shade. The bed shall be free from cracks, warping, knots and other defects and shall be complete in all respects, including all necessary hardware, screws, bolts, fittings, transportation and installation, as directed by the Engineer-in-Charge. |
| 93 | Providing and supplying 100 mm (4\\") thick mattress of size 3'-0\\" × 6'-6\\" (900 × 1950 mm), made of high-density PU foam/rebonded foam of approved quality and suitable firmness, conforming to relevant BIS standards, covered with good-quality, durable, washable and fire-retardant fabric/quilting cover with proper stitching and piping. The mattress shall be uniform in thickness, resilient, hygienic, free from defects and suitable for regular hospitality use, complete with all materials, stitching, finishing, transportation and installation, as directed by the Engineer-in-Charge. |
| 94 | Providing and fixing false ceiling in flat area using 12.5 mm thick Gypsum Plaster Board of approved make such as GypCeiling/Gyproc or equivalent, fixed to a suspended framework of GI metal channels, comprising perimeter channels, ceiling sections/main channels and intermediate/furring channels spaced at 600 mm (2'-0\\") c/c, suspended from the existing RCC slab/ceiling with GI hanger rods/bars and suitable approved GI suspension clips/fasteners at required spacing. The framework shall be securely anchored and properly levelled.The gypsum boards shall be screw-fixed to the GI framework with approved self-tapping drywall screws, with all joints treated using jointing compound and joint tape, including filling of screw heads, sanding and making the surface smooth and ready to receive primer/paint. The work shall include all necessary GI sections, hangers, clips, cleats, screws, fasteners, edge trims, jointing materials, cutting, making openings for electrical/AC fixtures, wastage, scaffolding and all other accessories, complete in all respects as directed by the Engineer-in-Charge. |
| 95 | Providing and fixing PVC fluted wall panelling in approved veneer finish, using high-quality, termite-resistant and moisture-resistant PVC fluted panels of approved make, colour, texture and pattern, as per the 3D design, approved shop drawing and instructions of the Architect/Engineer-in-Charge. The panels shall be fixed over a properly levelled and aligned framework/substrate using suitable GI/wooden battens, approved adhesive, screws, clips and necessary fasteners, as applicable.The work shall include proper setting out, cutting, trimming, mitred/corner joints, edge finishing, provision of required grooves, profiles and trims, treatment around electrical points, switches, doors and other obstructions, including all necessary accessories, adhesives, screws, framework, scaffolding, wastage, labour, transportation and installation, complete in all respects to achieve the required 3D decorative design and veneer-finish appearance, as approved by the Architect and Engineer-in-Charge. |
| 96 | Supplying & fixing of Outdoor Furniture as per drawing (Sample to be approved by Architect & as per direction of the Engineer-in-charge. |
| 97 | 4 seater Dining Table (Circular) |
| 98 | Dining Chair |
| 99 | 2 seater sofa |
| 100 | Centertable |
| 101 | Angular sofa |
| 102 | Coffee table |
| 103 | 4 seater Dining Table (Circular) |
| 104 | Dining Chair |
| 105 | 2 seater Dining Table (Circular) |
| 106 | Dismantling brick or stone masonry in lime or cement mortar under 3m height including stacking the useful materials for reuse and removing the debris within 50m lead. |
| 107 | Ground floor |
| 108 | Kitchen Equipment |
| 109 | TWO BURNER COOKING RANGE WITH ALL FITTINGS (Overall Size:- 1200X700X850+150)Body & Top:- Top Underneath by 40X40X5 thk. M.S. Angle Frame with rust proof paint, Covered by 16 S.W.G S.S 304 qualities Sheet at Top Portion and Side Covered by18 / 20 S.W.G. S.S. 304 quality Sheet with S.S. drip trays.Leg:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built.Others Fittings:- Fitted with Suitable heavy duty L.P.G. Burners, Needle Control Valve, Pilot Lamp & copper pipe with Heavy Duty C.I. Pan Support. |
| 110 | SINGLE BURNER COOKING RANGE WITH ALL FITTINGS (Overall Size:-600X700X850+150)Body & Top:- Top Underneath by 40X40X5 thk. M.S. Angle Frame, Covered by 16 S.W.G S.S Sheet at Top Portion and Side Covered by18 / 20 S.W.G. S.S. Sheet.Leg:- Fabricated from 40mmX40mm S.S. square pipe with adjustable fibber built.Others Fittings:- Fitted with Suitable heavy duty L.P.G. Burners, Needle Control Valve, Pilot Lamp & copper pipe with Heavy Duty C.I. Pan Support. |
| 111 | SINGLE SINK UNIT (Overall Size:- 600X700X850+150)Body & Top:- Top Underneath by 40X40X5 thk. M.S. Angle Frame, Covered by 16 S.W.G S.S 304 qualities Sheet at Top & Sink Bowl with Front Side (up-to Sink Bowl) Covered by 20 S.W.G. S.S. 304 quality Sheet.Leg:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built. |
| 112 | MASALA TABLE WITH 02NOS. BOTTOM SHELVE(Overall Size:- 450X700X850)Body & Top:- Top Underneath by 40X40X5 thk. M.S. Angle Frame with rust proof paint, Covered by 16 S.W.G S.S. Sheet at Top Portion and Bottom Shelve 18/20 S.W.G. S.S. Sheet.Leg:- Fabricated from 40mmX40mm S.S. Square pipe with adjustable fibber built. |
| 113 | WORK / SIDE TABLE WITH 02NOS. BOTTOM SHELVE (Overall Size:- 1500X700X850+150)Body & Top:- Top Underneath by 40X40X5 thk. M.S. Angle Frame with rust proof paint, Covered by 16 S.W.G S.S 304 qualities Sheet at Top Portion and Bottom Shelve 18/20 S.W.G. S.S. 304 quality Sheet.Leg:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built. |
| 114 | TRIPLE DOOR UNDER COUNTER FREEZER(Overall Size:- 1800X700X850) Body:- Fabricated from 40X40X5 thk. M.S. Angle Frame with rust proof paint, Top Covered by 16 SWG S.S. 304 qualities sheet. Out-side body Covered by 20 S.W.G S.S 304 qualities Sheet and Inner Tank 22/24 S.W.G. S.S. 304 quality Sheet. Spring fittings Door with lock & Key Facility.Leg:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built.Insulation:- Puff Type Insulation Body & Door.Cooling System:- Copper pipe coiling withdirect cooling System.Others Fittings:- Fitted with Emerson Makecompressor, Heavy Duty Fan / Motor, Heavy Duty Condenser with Copper Coiling, Digital temperature controller display & On-Off Switch fittings. |
| 115 | OVER HEAD SHELEV FOR UNDER COUNTER FREEZER (Overall Size:- 1800X250X450+300)All shelve 18SWG S.S. S.S. Sheet, Supporting Legs fabricated from 25mm dia. S.S. Pipe. |
| 116 | DOUBLE DOOR CHEST FREEZER (Capacity:-525ltrs. ) VOLTAS / Western Make |
| 117 | 1/1-03Nos. & 1/2-04Nos. G.N. PAN / CONTAINERS BAIN MARIE WITH ALL FITTINGS (Overall Size:- 1800X700X850)Fabricated from 40X40X5 thk. M.S. Angle Frame and covered by 16 SWG 304quality S.S. Sheet at top portion, 18/20 S.W.G. S.S. Sheet, Outside body and inner tank S.S. Sheet with Glass wool insulation 2KW heating element. |
| 118 | CUTTING TABLE WITH 02NOS. BOTTOM SHELVE (Overall Size:- 1500X700X850+150) Body & Top:- Top Underneath by 40X40X5 thk. M.S. Angle Frame with rust proof paint, Covered by 16 S.W.G S.S 304 qualities Sheet at Top Portion and Bottom Shelve 18/20 S.W.G. S.S. 304 quality Sheet.Leg:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built. |
| 119 | POTATO & ONION STORAGE BIN (Capacity:- 100Kg + 100Kg) Fabricated from 40X40X5 thk. M.S. Angle Frame at bottom and all body solid rod with heavy duty wheel. |
| 120 | TILTING WET GRINDER Standard, Capacity:- 10Kg / Charge S.S. Body & 01HP Heavy Duty Motor, Single Phase |
| 121 | 4”- DEEP SOIL DISH LANDING TABLE WITH SOIL HOLE & OVER HEAD SHELVE (Overall Size:- 1500X700X850+450+300)Body & Top:- Top Underneath by 40X40X5 thk. M.S. Angle Frame with rust proof paint, Covered by 16 S.W.G S.S 304 qualities Sheet at Top Portion &Over head shelve 18 S.W.G. S.S. 304 quality Sheet & 25mmDia Pipe.Leg:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built. |
| 122 | 02-SINK UNIT (Overall Size:- 1100X700X850+150)Sink Bowl Size:- 500X500X300 Depth. Body & Top:- Top Underneath by 40X40X5 thk. S.S. M.S. Angle Frame with rust proof paint, Covered by 16 S.W.G S.S Sheet at Top & Sink Bowl with Front Side (up-to Sink Bowl) Covered by 20 S.W.G. S.S. 304 quality Sheet.Leg:- Fabricated from 40mmX40mm S.S. square pipe with adjustable fibber built. |
| 123 | CLEAN / SOIL DISH LANDING TABLE (Overall Size:- 750X700X850) Body & Top:- Top Underneath by 40X40X5 thk. M.S. Angle Frame with rust proof paint, Covered by 16 S.W.G S.S 304 qualities Sheet at Top Portion and Bottom Shelve 18/20 S.W.G. S.S. 304 quality Sheet.Leg:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built. |
| 124 | CLEAN DISH RACK WITH 04NOS. SHELVE (Overall Size:- 1100X450X1650) Shelve:- Shelve Fabricated From 18 S.W.G. S.S 304 qualities Sheet. Leg / Supporting Stand:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built. |
| 125 | POT RACK WITH04NOS. SHELVE (Overall Size:- 1500X600X1800) Shelve:- Shelve Fabricated From S.S. 304 qualities 20mm / 25mm square pipe.Leg / Supporting Stand:- Fabricated from 40mmX40mm S.S. 304 quality square pipe with adjustable fibber built. |
| 126 | S.S. SUCTION HOOD WITH S.S. BAFFLE FILTER FOR COOKING RANGE TOP (CANTILEVER TYPE)1200X900X450/500 Fabricated from 20/22 SWG S.S. 202Quality S.S. Sheet & S.S. Baffle Filter with Double frame for Suction Hood Fabricated from 24 SWG S.S. sheet. |
| 127 | AIR CONTROL DAMPER (Overall Size:- 300X300X100) Fabricated from 24 G.I. SWG sheet. |
| 128 | G.I. DUCTING INSIDE & OUT-SIDE KITCHEN FOR EXHAUST SYSTEM (Overall Size:- Different) Fabricated from 22/24SWG G.I. sheet. |
| 129 | 2HP EXHAUST BLOWER / CENTRIFUGAL FAN 2 HP Crompton Greaves / Marathon/ ABB Make Motor (6 pole, 1 Phase) having air handling capacity 10000CFM at 4” water Column pressure. |
| 130 | Internal & External Electrical works |
| 131 | Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI/V-Guard with 20 mm dia HMS FRLS PVC conduit ISI marked Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal 6A modular type ( flame retradant type) switch ISI marked Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) ( flame retradant type) Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) of suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. . All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. |
| 132 | GROUP-A |
| 133 | GROUP-B |
| 134 | GROUP-C |
| 135 | Supplying ,fixing of 6A Plug on the same board in existing switch board with complete fitting by 01 no of 6A switch & socket (modular type)( ( flame retradant type)) & other required accessories of ISI marked as approved as per direction of Engg. -in -Charge. Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 136 | Supplying,fixing of 6A Plug on the separate board with complete fitting by 01 no of 6A switch & socket(modular type)( ( flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider(Zencelo)/legrand( Myrius ) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a period of 2 years against manufacturing defects against which ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 137 | Supplying,fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket(modular type)(( flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge.. Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision) (For equipement power)All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 138 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 1.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor. In 20 mm dia non metallic heavy duty conduit (LDB to LSB/LIGHT CKT)(2X1.5+1X1.5) |
| 139 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge.2 nos single core 2.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit.(BDB to LSB/LIGHT CKT/5A PLUG/UPS POINT ) (2X2.5+1X1.5) |
| 140 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge.2 nos single core 4 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit .(PDB to PSB/ POWER POINT/AC POINT) (2X4+1X1.5) |
| 141 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI /V-Guard in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge.4 nos single core 6 sq. mm copper wire for phase and neutral and 02 nos of single core 4 sq. mm copper wire for earth continuty conductor in 32 mm dia non metallic heavy duty conduit.(LFDB TO LBDB) (4X6+2X4) |
| 142 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI /V-Guard in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge.4 nos single core 10 sq. mm copper wire for phase and neutral and 02 nos of single core 6 sq. mm copper wire for earth continuty conductorin 32 mm dia non metallic heavy duty conduit .(LFDB TO FLOOR PANEL TO TPN BDB power) (4X10+2X6) |
| 143 | Supplying and installation of AC Point having 16-20A DP MCB, C series with enclosure, Schneider/Siemens/Legrand/ABB c of suitable size as required as per direction of Engg.-in-Charge .All the Components should be warrantied for a replacement period of 1 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 144 | Supplying,fixing of 2 nos 6A Plug on the separate board with complete fitting by 02 no of 6A switch & socket(modular type)( (flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a period of 2 years against manufacturing defects against which ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 145 | Supply and fixing CALL bell (Ding dong type) /Buzzer on the existing switch box/cover.Make- Havells/Anchor as required as per direction of Engg.-in-Charge.All the Components should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 146 | S/F of Bakelite angle holder/batten holder (make-Anchor/Havells or equievalant reputed make A catagory ISI marked as approved )of ISI marked conforming to IS-1258/1987 in place of ceiling rose as per direction of Engg.-in-Charge .All the Components should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. |
| 147 | S/F of 5 step type Modular electronic Fan Regulator ISI Marked with all connection complete in all respect as per direction of Engineer in charge ( Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision) |
| 148 | Sub-Head II (Light fitting Fixture & Fan) |
| 149 | Supplying, installation, of exhaust fan of heavy duty 300 mm sweep 1400 rpm with louvers (Make- Havells/Crompton/Usha/Orient/Bajaj ) of exhaust fan in the existing wall, including fixing & conntection as required as per direction of Engg.-in-Charge. Replacement Warranty will be 2 years. |
| 150 | Supply, Installation, Testing and Commissioning of Duct mounted Single skinned Circular Inline Centrifugal Fan for Toilet Ventilation with direct driven Backward-curved impellers.The Fan has external rotor motor suitable for 1~, 230V, 50 Hz power supply. MAKE - SYSTEMAIR/ GREENHECK/ ELTA/Airflow1500 CFM @ 15mm MMWG static pressure |
| 151 | Supply & Fixing of Air Distribution Duting fabricated with Class VI GI Sheet(180 GSM) Complete With Supports, dampers, guiding vanes, access doors, MS Angle, Fire inhibiting gaskets, Nuts, bolts and all oyher accessories in accordance with approved drawing and the Specification. (Make:- Jindal/ Sail/ Tata)22 gauge (0.80 mm thickness) |
| 152 | 24 gauge (0.63 mm thickness) |
| 153 | Supply, erection, testing & commissioning of Aluminium powder coated grills/diffuser without VCD having flange all around.Make-Glenstorm/Airflow/Systemaire |
| 154 | Supplying, installation, testing and commssioning of 1200 mm sweep Copper wound BLDC ceiling fan with aluminium blades having wattage not more than 28W and air delivery ≥215m3/min Make-Crompton Energion Groove /Havells Efficiencia Neo/Usha Technix /Bajaj Turbo Pro 12DC5 ) including wiring the down rod of standard length (upto 30 cm) with 1.5 sq mm PVC insulated, copper conductor, single core cable etc. as required as per direction of Engg.-in-Charge,Replacement Warranty will be 4 years. |
| 155 | Supplying and fixing of Energy efficient surface /recess mounted square /round shape 18 W LED luminaire of dimension of consists of white powder coated , die-cast Alluminium housing with high quality frosted diffuser for glare-free uniform lighting distribution with wattage not more than 18 watt and lumen output of 1800 lumens, , CRI not less than 80,CCT of 6000 degree K,THD less than 10%, with electronic driver, internal surge protection of 3 KV , L70 B50: 50000 hrs and all other accessories suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj).The luminaire should be Replacement Warranty will be 2 years |
| 156 | SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 20 watt and lumen output not less than 2200 lumen complete with electronic driver and all other accessories with diffuser having 2 years warranty i/c connection etc as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 2 years . |
| 157 | SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj)The luminaire should be Replacement Warranty will be 2 years |
| 158 | Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as requiredas required as per direction of Engg.-in-Charge .(Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)of ISI mark as approved. |
| 159 | SITC of recess/surface mounted 2'x2'(595mmx595mmx70mm(+/-5%) square shaped LED made up of CRCA powder coated housing with lumen efficacy not less than 140lm/W and lumen output not less than 3600 lumens , CRI not less than 80, CCT of 5700-6500 degree K, THD less than 10%,internal surge protection of 3 KV, complete with Non integrated isolated electronic driver (protects the output /secondary side from any disturbance on the input / primary side ensuring safe operation)and all other accessories suitable for operation on140- 270 V, 50 Hz ,L70 @50,000 burning hrs (5 years warranty) as required as per direction of Engg.-in-Charge (Make: Panasonic/ LT/ Havells / Philips/ Wipro/ Crompton/ Bajaj) . The luminaire must be Replacement Warranty will be 5 years. |
| 160 | SITC of indoor rated IP20 5mtr LED Strip, operating in an ambient temperature of 0⁰C to 45⁰C. Operating at 50Hz frequency, housing of Polymide double sided PCB. LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. Luminaire should have 70lm/mtr and total 350lumen in maximum 25Watt for 5mtr role. The LED shall comply with L70 life of 35000 burning hours tested at maximum current. The LEDs used should be with CCT of 3000/4000/5700 K. LED Driver shall be external type, suitable to operate in input voltage range of 140V to 300V (nominal rated voltage – 240V) with 3KV internal surge protection, Power factor of minimum 0.9, driver efficacy of minimum 85% and total harmonic distortion (THD) of less than or equal to 20% should be integral to the luminaire. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj).The luminaire should be Replacement Warranty will be 2 years |
| 161 | SITC of 20 watt LED focus track light with 1mtr track as per the direction of Engineer-in-charge. (Make:K-LITE Model No- 23678 Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 2 years . |
| 162 | SITC of 12 watt LED COB light made up of die cast aluminium body & Clear polycarbonate diffuser with 100Lm/Watt, Citizen COB, IP-54, SDCM<3, CRI 90, CCT - 3000K, as per the direction of Engineer-in-charge. (Make: K-Lite Model No - 28178 / Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 2 years . |
| 163 | BDBS,DB,AC DB,FLOOR PANELS,MCBS |
| 164 | Supplying and fixing of following mentioned way, three pole/single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3,integrated door earthing system offering additional safety to the user,High quality polyurethane Gasket,the box and cover shall be fabricated to withstand IK09,the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface/recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make-LEGRAND-Ekinox3 DB/ Siemens-Betaguard/ Schneider- Acti 9/ABB Itus as per direction of Engg.-in-Charge. The Distribution boards should be Replacement Warranty will be 3 years |
| 165 | Supply and fixing of 8 way DD single pole and neutral sheet steel MCB distribution board 250V on surface/recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (but with out MCB/ RCCB/ Isolator).Warranty on DB is 3 years (toilet,ticket counter,ups of food av,galerry,art craft) |
| 166 | 4 Way(8+12) Way TPN MCB DD DB Horizontal Type as per IEC 61439-3 suitable for Flush mounting and Surface mounting with 100A Copper Bus Bar for each phase, with neutral Bus bar, Earth Bar & Cable ties for cable management, prefitted masking sheet, IP43-IK09 with metal door Warranty on DB is 3 years (FOR art craft,eco,galerry,food av,com hall,godown power light)) |
| 167 | 8 Way(8+24) Way TPN MCB DD DB Horizontal Type suitable for Flush mounting and Surface mounting with 100A Copper Bus Bar for each phase, with neutral Bus bar, Earth Bar & Cable ties for cable management, prefitted masking sheet, IP43-IK09 with metal door(FOR POWER & INDOOR AC DB)Warranty on DB is 3 years (FOR art craft,eco,galerry,food av,com hall power light,godown power)) |
| 168 | 2+4 way MCB Enclosure DB (GLAZED door)(only each EM. CONNECTION UPS LOAD)Warranty on DB is 3 years (ups of galerry,eco,ar,shop) |
| 169 | Supplying and fixing 6- 32 amps rating, 240 volts, C series, Double poles MCB of Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years .for 2+4way db |
| 170 | Supplying and fixing 6 amps to 32 amps rating, 240 volts, C series, single poles MCB of Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 . the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years. |
| 171 | Supplying and fixing 40Amps 4P 415 volts, MCB Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 in the existing MCB DB in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years |
| 172 | Supplying and fixing 40 Amps rating, RCCB 30mA,415V . Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB FB 200 in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge. . The RCCB should be Replacement Warranty will be 1 year. |
| 173 | Supplying and fixing 40 amps rating, 240 volts, C series,10KA breaking capacity, Double poles MCB of Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. .Warranty on MCB is 1 year. |
| 174 | Supplying and fixing 63Amps 4P 415 volts MCB 415 volts, C series,10KA breaking capacity, Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 in the existing MCB DB with connections as per direction of Engg.-in-Charge..Warranty on MCB is 3 years. |
| 175 | Supplying and fixing 63Amps 4P 415 volts RCCB 30 mA Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB FB 200 in the existing MCB DB complete with connections as per direction of Engg.-in-Charge..The RCCB should be Replacement Warranty will be 1 year. |
| 176 | Supplying and fixing 40Amps 2P 240 volts RCCB 30 mA Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB FB 200 in the existing MCB DB complete with connections as per direction of Engg.-in-Charge..The RCCB should be Replacement Warranty will be 1 year. |
| 177 | CABLING AND END TERMINATION MAIN AREA |
| 178 | Supplying of one number PVC insulated armoured and PVC sheathed XLPE property AL. conductor power cable of 1.1 KV grade Make- Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster of following size cables as per direction of Engg.-in-Charge. |
| 179 | 4core x 16 sq mm(BDB IC) |
| 180 | 3.5core x 150 sq mm DG |
| 181 | 3.5core x 95 sq mm (EV,ALL SUB PANEL) |
| 182 | 3.5core x 50 sq mm (SUB PANEL 2W EV) |
| 183 | 3.5core x300 sq mm (MAIN PANEL MAIN IC) |
| 184 | LAYING OF CABLE |
| 185 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge. |
| 186 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size exceeding 120 SQ. MM but not exceeding 400 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge. |
| 187 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the EXISTING PIPE etc as required as per direction of Engg.-in -charge. |
| 188 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size exceeding 25 SQ. MM but not exceeding 400 SQ. MM direct in ground in the EXISTING PIPE etc as required as per direction of Engg.-in -charge. |
| 189 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM in open duct etc as required as per direction of Engg.-in -charge. |
| 190 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size exceeding 25 SQ. MM in open duct 400 SQ. MM direct in ground in the EXISTING PIPE etc as required as per direction of Engg.-in -charge. |
| 191 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM in surface with shaddle and screw etc as required as per direction of Engg.-in -charge. |
| 192 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size exceeding 25 SQ. MM but not exceeding 120 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge. |
| 193 | Supplying and making end termination with brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. |
| 194 | Supplying and making end termination with 4 core x16 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. |
| 195 | Supplying and making end termination with 3.5 core x95 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. |
| 196 | Supplying and making end termination with 3.5 core x150 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. |
| 197 | Supplying and making end termination with 3.5 core x50 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. |
| 198 | Supplying and making end termination with 3.5 core x300 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. |
| 199 | Providing,fixing and laying of following dia G.I. pipe (medium class) in ground complete with G.I fitting incl. trenching(75 mm depth)and refilling as per direction of Engg.-in-Charge. |
| 200 | 50 mm dia |
| 201 | Supplying,laying of 3cx2.5 sq.mm copper flexible cable with insulated cover with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials(make-Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster ) |
| 202 | Supplying,laying of 3cx2.5 sq.mm AL armoured XLPE cable with insulated cover with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials(make-Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster ) |
| 203 | Supplying,laying of 3cx6 sq.mm AL. armoured XLPE cable with insulated cover with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials(make-Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster ) |
| 204 | Providing,fixing and laying of fallowing dia HDPE pipe (medium class) in ground complete with fitting incl. trenching(75 mm depth)and refilling as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials |
| 205 | 50 mm dia |
| 206 | PANELS |
| 207 | MAIN CONTROL PANEL |
| 208 | S/I/T&Commissioning of LT OUTDOOR floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing. (FOR ALL MAIN CONNECTED LOAD)as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.3P+N Type 1+2 SPD 65 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. 80X10MM Separate Aluminium Earth bus bar should be installed.Provision of cable alley chamber is mandatory. All the feeders shall have ON/OFF/TRIP indication. |
| 209 | In commer-1-01 number of 630A 4P Icu=100%Ics,36Ka LSIG MCCB with microprocessor release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 210 | In commer-2- 01 number of 200A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 211 | Changeover- 01 no of 200A 4P onload changeover switch ( DG 01 NO)(Make-Legrand/Siemens/Schneider/ABB) |
| 212 | Busbar-1&2 04 numbers of 800Amps Aluminium busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing) |
| 213 | Out going- 01 numbers of 200 Amps 4P MCCB.Icu=100%Ics,25Ka TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 214 | Out going- 05 numbers of 125Amps 4P MCCB.Icu=100%Ics,25Ka TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 215 | Out going- 02 numbers of 160Amps 4P MCCB.Icu=100%Ics,25Ka TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 216 | Out going- 9 numbers of 100-63Amps 4P MCCB.Icu=100%Ics,16Ka TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 217 | Out going- 1 number of 100Amps 4P MCCB Motorized .Icu=100%Ics,25Ka ,LSING ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula for Solar on grid integrate . |
| 218 | Outgoing- 4 nos. 32A 4P MCB, C series, 10 ka , Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 |
| 219 | Outgoing- 8 nos. 32A 2P MCB, C series, 10 ka , Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200(Among it 2 nos with space for KWH Meter for shop) |
| 220 | Instrument- (i) 06 numbers phase indicating lamp with toggle switch & HRC fuse. |
| 221 | (ii) 02 set of digital type multifunction meter with CT for voltage,current,frequency,PF,THD indication(iii) All the MCCB outgoing feeders shall have digital ammeter with CT of suitable class 1 rating.(Make-Legrand/Siemens/Schneider/ABB)(iv) 3P+N Type 1+2 SPD 65 kA with 100A 4P MCCB,25kA, TMR, Ics=100%Icu shall be installed in the incomers. (Make of SPD-Legrand/Siemens/Schneider/ABB),Make of MCCB-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 222 | MAIN CONTROL PANEL DORMITORY |
| 223 | S/I/T&Commissioning of LT INDOOR floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing.as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.3P+N Type 2 SPD 40 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. 20X10MM Separate Aluminium Earth bus bar should be installed.Provision of cable alley chamber is mandatory.All the feeders shall have ON/OFF/TRIP indication. |
| 224 | In commer-1-01 number of 160A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 225 | In commer-2- 01 number of 100A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 226 | Changeover- 01 no of 100A 4P onload changeover switch ( DG 01 NO)(Make-Legrand/Siemens/Schneider/ABB) |
| 227 | Busbar-1&2 04 numbers of 200Amps Aluminium busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing) |
| 228 | Out going- 4 numbers of 6-32A 2P MCB10KA,C series ( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) |
| 229 | Out going- 4 numbers of 6-32A 4P MCB10KA,C series ( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) |
| 230 | Out going- 3 numbers of 63A 4P MCB10KA,C series ( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) |
| 231 | Instrument- (i) 03 numbers phase indicating lamp with toggle switch & HRC fuse. |
| 232 | (ii) 01 set of digital type multifunction meter with CT for voltage,current,frequency,PF,THD indication(iii) 3P+N Type 2 SPD 40 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. (Make of SPD-Legrand/Siemens/Schneider/ABB),Make of MCB-LEGRAND-DX3 / Siemens-Betaguard Model/ Schneider-Acti-9 /ABB SB200 |
| 233 | SHOP PANEL |
| 234 | S/I/T&Commissioning of LT INDOOR floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing.as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.3P+N Type 2 SPD 40 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. 20X10MM Separate Aluminium Earth bus bar should be installed.Provision of cable alley chamber is mandatory.All the feeders shall have ON/OFF/TRIP indication. |
| 235 | In commer-1-01 number of 125A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 236 | In commer-2- 01 number of 100A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula |
| 237 | Changeover- 01 no of 100A 4P onload changeover switch ( DG 01 NO)(Make-Legrand/Siemens/Schneider/ABB) |
| 238 | Busbar-1&2 04 numbers of 200Amps Aluminium busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing) |
| 239 | Out going- 17 numbers of 40A 2P MCB10KA,C series ( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200Fallowed by space for 1PH KWH 10-40A Energy meter) |
| 240 | Instrument- (i) 03 numbers phase indicating lamp with toggle switch & HRC fuse. |
| 241 | (ii) 01 set of digital type multifunction meter with CT for voltage,current,frequency,PF,THD indication(iii) 3P+N Type 2 SPD 40 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. (Make of SPD-Legrand/Siemens/Schneider/ABB),Make of MCB-LEGRAND-DX3 / Siemens-Betaguard Model/ Schneider-Acti-9 /ABB SB200 |
| 242 | CABLE TRAY /RACE WAY FOR DISTRIBUTION OF POWER |
| 243 | Supplying,fixing of perforated cable trays with horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 200mm(W) of MAKE- Profab/OBO/Neidax.The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge. |
| 244 | Supply ,installation ,testing & commissioning of 5 KVA UPS SYSTEM WITH IGBT based inverter system, true online double conversion system, inbuilt isolation transformer & automatic phase sequence corrector of 3ph in put to 1 ph output,415V, with built in BMS with battery back up up to 30 minutes with MS Rack for battery Housing, DC cable 7 Mtr with SFU and links for installation (Battery required: 12V, 42AH, 20 No.s) protection for fault by OL,UV,EF,GF,OC,Ph. (Make:Numeric/APC/ Vertiv/) , as per direction of Engg.-in-Charge. Warranty period of all accessories & component & system must be 2 years & complete test certificate must be submitted along with ups including component list & SLD. for AV,ART CRAFT,GALERRY,MULTI HALL) |
| 245 | EARTHING |
| 246 | Supplying,installation,testing & commissioning Of Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required as per direction of Engg. in charge. |
| 247 | Supplying & laying of 6 swg GI WIRE at 0.5m below the ground as strip earth electrode including connection/termination with nut ,bolt ,spring washer etc as required(jointing shall be done by over laping and with 2 sets of brass nut ,bolt & spring washer spaced at 50mm . as required as per direction of Engg. in charge. |
| 248 | Supplying & laying of 25mm x 5 mm GI strip at 0.5m below the ground as strip earth electrode including connection/termination with nut ,bolt ,spring washer etc as required(jointing shall be done by over laping and with 2 sets of brass nut ,bolt & spring washer spaced at 50mm . as required as per direction of Engg. in charge. |
| 249 | LIGHT SYSTEM EXTERNAL |
| 250 | Supply , Installation, Testing and commissioning of 5meter Florus Lighting Pole long aesthetically Trishul Design on top and shankh/chakra design on arm designed single Arm decorative lighting pole supplied with -3000K-Type II-Polycarbonate Optical Lens 100W LED decorative light having 80Lm/W Lumen output and made up of Spun Aluminium body & Milky acrylic (A9) diffuser 5m Lighting Pole Lighting Pole Height (in mm): 5000mm Pole Size: Ø76.1 PoleType: Pole shall be made up of Mild Steel Body and coated with zinc rich primer & pure polyester powder coating of Black Finish. Base Plate size of Ø230x12mm thick with provision for founation bolt. Pole is Compatible for Ø70mm size for cable entry & exist. Junction Box service door is made up cast aluminium and the control gear tray only is prewired with 2.5sq mm cable, 6A SP MCB and 32A 4pole terminal connector for loop-in loo-out arrangement with all materials & labour as required as per the direction of Engineer-3000K-100W LED Milky Acrylic Diffuser : Sq.445 x 713mmc Black Powder Coating-RAL 9004 Black-3 Years.(MAKE: klite( Pelican fort+ KP-12016 Bishop Lighting Pole )/Philips/Reytek/Homdec/Jaquar) |
| 251 | Supplying, Erection, Fixing, connection & testing of 50W LED Heritage GATE Light, Dimension of light must be Ø400mm dia and 800mm height, IP 66, IK07, amb. temp -10 to 45 degree celcious, CT 3000-5700K,,50000 HRS, CRI 70, 120 Lm/W system efficacy,driver efficiency >/ 85%,dia case aliminium housing,Clear Acrylic diffuser of Make-K-LITE Model No - 25444/LT/panasonic/Havells /Philips/Wipro /Crompton/Bajaj as approved maintenance free having 2 years warranty G.I P ipe with braket including MCB box & including with foundation as per the Drawing for inspection as required & as per direction of Engg.-in-Charge. |
| 252 | Supply , Installation, testing & commissioning of 24W LED Vista Bollard light of Dimension: Ø250 x 900mm having Spun Aluminium with Extruded Aluminium Tube(Grade 6063) housing and coated with zinc rich primer & pure polyester powder coating of Antique Copper Finish, UV Stabilized Translucent Polycarbonate diffuser. Bollard should be Customized Bespoke CNC cutting design with CCT-3000K, CRI-≥80, IP-65, IK-08, SDCM≤ 3, Lumen maintainance >60,000 burning hours as per L70 B10, Power Factor : >0.9, THD : <10%, Surge Protection : Inbuilt 4KV, Efficiency : >80%, Optical Distribution : Symmetrical. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66/65 protection and other parameters as required by the Engineer-in- Charge. (Make: K -lite Vista Bollard 24572 or, , similar to Jaquar/Bajaj/Reytek/Homdec). |
| 253 | Installation of Bollard Light by making the suitable size foundationwith necessary civil work and fixing the bollard light equievalant make ISI marked as approved as per direction of Engg. in Charge. |
| 254 | CABLING |
| 255 | Supplying and laying of one number PVC insulated armoured and PVC sheathed XLPE AL. conductor power cable of 1.1 KV grade POLYCAB/FINOLEX/HAVELLS/KEI/RR Kabel/Gloster of following size cables as per direction of Engg.-in-Charge.Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials |
| 256 | 4core x 16 sq mm (OFP TO IND. TIMER PANEL) |
| 257 | 4 core x 4 sq mm (for small power/LIGHT TO POLE) |
| 258 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge. |
| 259 | Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size exceeding 25 SQ. MM but not exceeding 120 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge. |
| 260 | Supplying and making end termination with brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. |
| 261 | Supplying and making end termination with 4 core x16 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. |
| 262 | Supplying,laying of 3cx2.5 sq.mm copper flexible cable with insulated cover of reputed make,ISI marked with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. Make-POLYCAB/FINOLEX/HAVELLS/KEI/RR Kabel/Gloster |
| 263 | Providing,fixing and laying of fallowing dia HDPE pipe (medium class) in ground complete with fitting incl. trenching(75 mm depth)and refilling as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials |
| 264 | 50 mm dia |
| 265 | S/I/T&Commissioning of LT OUT DOOR FLOOR mounted cubical type IP66 based panel made out by 2mm CRCA steel sheet duly derusted & pented by simens gray powder cote paint is designed as G.A drawing. (FOR USE) with 63A TPN MCB 01 NO,1 no. Astronomical digital timer, AUTO MANUAL(with start and stop push button) SELECTOR 63 A 3P contactor, OLR,RYB,ON,OFF trip indication, Type-II SPD 40ka ,,04 nos 10A 4P MCB,C,10KA as outgoing MCB( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period 1 years of acceptance of materials |
| 266 | MINImast lighting |
| 267 | Supply,installation,testing and commissioning of 8M mini mast shaft in two sections suitable for 55 m/sec wind speed along with head frame, luminaires carriage suitable for 6 luminaires in symmetrical arrangement and other accessories manufactured in factory. ( Bottom 360mm / Top -150mm, 3mm thickness, 445PCD, diameter of base plate 520mm including supplying of raising lowering system comprising double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightning finial. (Wiring material from JB to individual luminaire & MCB in base compartment are not included and are a part of installation)along with foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template along with Construction of shallow foundation with M20 grade concrete for the highmast considering the safe soil bearing capacity at site as 10 T/sqmtr at 2 metre depth with all materials and labour.Erection of the high mast with the help of suitable tools and plants, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 1.5 sq. mm, lugs, MCB and all labour . Provision of GI pipe earthing for High mast with 2.5 M long 40 mm dia GI Pipe including connection to High mast earth terminal with 25 x 3 mm GI flats with all materials and labour. (2nos per mast required) Approved colour after treatment along with provision of masonary pedestal duly finished with plaster and painting with GI pipe for cable entering as required.. (2nos per mast required) (Make:-Bajaj/ Utkarsh/ Vakrangee/RR ISPAT/Valmont |
| 268 | SITC of 150W Outdoor Flood LED lights with silicon potted driver, IP66, , bottom opening maintanance , LPW not less than 130.Input Voltage: 85-265V AC ,Body : Die cast Aluminium, IP66 as per the Drawing for inspection as required & as per direction of Engg.-in-Charge. Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj as rerquired. |
| 269 | LED type single dome aviation obstruction light. (Make:-Bajaj/ Utkarsh/ Vakrangee/RR ISPAT |
| 270 | S/I/T&Commissioning of LT OUT DOOR FLOOR mounted cubical type IP66 based panel made out by 2mm CRCA steel sheet duly derusted & pented by simens gray powder cote paint is designed as G.A drawing. (FOR USE) with 63A TPN MCB 01 NO,1 no. Astronomical digital timer, AUTO MANUAL(with start and stop push button) SELECTOR 63 A 3P contactor, OLR,RYB,ON,OFF trip indication, Type-II SPD 40ka ,,04 nos 10A 4P MCB,C,10KA as outgoing MCB( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period 1 years of acceptance of materials |
| 271 | ELV-CCTV ,PA SYSTEM |
| 272 | SITC of 5MP IP Bullet/Dome Camera with inbuilt microphone, equipped with 1/2.7\\" Progressive Scan CMOS image sensor and 3.6/2.8(for dome) mm fixed lens, supporting a resolution of 2592 × 1944 or higher. The camera shall provide IR illumination up to 30 meters and an approximate field of view of 79° (H)/97(for dome), 56°/70(for dome) (V), and 106°/128( for dome) (Diagonal). Minimum illumination shall be 0.003 lux @ F1.6 (AGC ON) with support for WDR (120 dB). The camera shall support video compression formats such as H.265+, H.265, H.264+, H.264 and MJPEG, with multiple streaming capability including main stream up to 5MP @ 30 fps, sub-stream up to 1080p @ 30 fps, and additional third stream. The camera shall support intelligent analytics such as human and vehicle detection, perimeter intrusion detection, line crossing detection, object detection, heat map, crowd density detection, queue length detection, and rare sound detection. The device shall support motion detection with multiple configurable zones and network protocols including TCP/IP, HTTP, DHCP, RTP/RTSP, SMTP, NTP, UPnP, SNMP, HTTPS and SFTP, and shall be ONVIF compliant (Profile S/G/T). The camera shall include micro SD card slot up to 256 GB/512 GB( for dome), privacy masking, ICR auto day/night switching, and support 12V DC or PoE power supply. The housing shall be metal body with IP67 weatherproof protection, suitable for outdoor installation. The product shall comply with NDAA requirements and shall be certified with STQC, BIS, CE, FCC and RoHS. Make-Honeywell Value series/Pelco/Axis/Bosch |
| 273 | Supply, Installation, Testing & Commissioning of 5MP IP Network TDN Low-Light IR motorized Lens Dome/Bullet Camera, 1/2.8\\" CMOS or better, 5MP (2592 x 1944) @ 25fps or better, four stream at various resolution & Frame Rates, Min. Illumination required 0.005 lux (color), 0 Lux IR On, 3 IR LEDs, Smart IR with upto 70m(bullet)/50m(dome) IR distance, Auto ICR (Infrared Cut Filter) 130dB True WDR, S/N Ratio 55db, Shutter Speed 1/3 - 1/100,000; Adavance Video Compression technology such as H.265 HEVC/ H.264 / MJPEG , Fixed Lens 2.7-13.5mm motorized, Field of View FoV H:100-28.5°, V:73-21.4°, BLC, HLC, WDR, 2D/3DNR, White Balance - Auto/Manual/Day/Night/timing, Minimum Edge Intelligence Video Analytics : Video Motion Detection, Tampering, Loitering, Intrusion, & People Counting, 5 Privacy Mask, 6 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 2TB SD card support, PoE (802.3 af) and 12V DC, IP 66/67 & IK10 Vandal proof with Die Cast Aluminium Housing, Having Operating temp range : –30°C to 60° C. Certifications: ONVIF Profile S/G/T compliant,, CE (EN 50130-4), FCC Part 15, EN 55032 & RoHS (EN63000),NDA,STQC compliant. Make-Honeywell value series/Pelco/Axis/Bosch |
| 274 | Supply , Installation, testing , commissioning of 64 Channel NVR with 8 SATA; 384 Mbps incoming bandwidth, Up to 8 Megapixels Resolution Display and Recording, H.265 video compression technology with real time encoding, Full function CMS (Central monitoring software) supported, Two way audio supported, Dual streaming technology to encode recording stream and network stream separately, Supports remote monitoring on Mobile Client (Android, IOS), TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP, Time/ Date, Alarm, Motion Detection & Exact Search (accurate to second), Record Snapshot, FTP, Preset Calling, Email notification supported, Manual/ Alarm/ Motion Detection/ Continuous, CE, FCC, RoHS). Make-Honeywell value series/ Pelco/ Axis/ Bosch |
| 275 | Supply, Installation,Testing & Commisioning of Surveliance 10 TB HDDMake:- WD/Segate/Toshiba |
| 276 | SITC of Certified HDMI® Interface Cable, 18 Gbps, 15 m Makes: Honeywell, Extron, Kramer |
| 277 | SITC of 55\\" UHD IPS Commercial Digital Display for Small Size Discussion & Chambers: Brightness (440 nits or higher), Dynamic Contrast Ratio (Dynamic MCI (Hz)):1000000:1), 1000000:1, Static (Panel) Contrast Ratio-1200:1, Response Time (G to G)-8 ms, Refresh Rate.-60 Hz, Life span (hrs)-30,000, Speaker (Sound Output):10W + 10W, Speaker System: 2.0 ch, DVB-T2/C Broadcasting System, Commercial Smart UX, webOS version (webOS 6.0), BIS Certification with 3 years onsite warrenty. Make: LG/Samsung/Sony |
| 278 | SITC of outdoor type double jacketed 4 pair Cat6 23 awg U/UTP LSZH Cable in the existing surface/ recessed steel/ PVC conduit as required: The 4 pair Unshielded Twisted Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must,Insertion Loss of 32.8 db/100m at 250 MHz ,Cable should support operating temperature from -20° to +70°C Cable support Conductor Resistance ≤ 9.38 Ω/100m Max., Cable support Delay Skew: < 45 ns/100m, Operating Voltage: 72V , Impedance: 100 ± 15 Ω @100 MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance up to 700 MHz , RoHS Compliant. Make: Systimax, Legrand, Panduit |
| 279 | SITC of 4 pair Cat6 23 awg U/UTP LSZH Cable in the existing surface/ recessed steel/ PVC conduit as required: The 4 pair Unshielded Twisted Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must,Insertion Loss of 32.8 db/100m at 250 MHz ,Cable should support operating temperature from -20° to +70°C Cable support Conductor Resistance ≤ 9.38 Ω/100m Max., Cable support Delay Skew: < 45 ns/100m, Operating Voltage: 72V , Impedance: 100 ± 15 Ω @100 MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance up to 700 MHz , RoHS Compliant. Make: Systimax, Legrand, Panduit |
| 280 | SITC of Cat6 I/O with Dual Face plate: The Outlet shall meet or exceed requirement as per ANSI/TIA 568C.2,ISO/IEC 11801, & EN50173. The information outlet NEXT, PSNEXT, FEXT, ELFEXT, PSELFEXT and return loss should be verified for CAT6 @ 250Mhz & CAT6A @ 500Mhz. The information outlet connector shall be of gold/nickel, thickness of gold > 0.8 μm. The connectors shall be compatible as per IEEE 802.3af standard for POE application. The PVC material of Face plate should complie ABS /UL94-V-O certified. Make: Systimax, Legrand, Panduit |
| 281 | SITC of Rack mount Draw Type Loaded 6 port LIU available in Standard 19” ,Dimensions (mm) : 430 X 220 X 1U , Cold Rolled Steel as Raw Material , Consist of Top Cover and Bottom Panel , Easy to Assemble and Dissemble , Three Types of Input Holes Cable Entry Through Water Proof Cable Clamp , 12 Duplex SC or LC Adapter Interface , Splice 24 Fibers at Most with 1 Tray ,Adaptor, SM, Duplex SC, PC Type ,Pigtail, Support the TIA/EIA Telecommunication Wiring Standards. Compact Design , Telcordia GR-326-Core . Make: Systimax, Legrand, Panduit |
| 282 | SITC of Cat 6, 24-port loaded, 1U Modular Jack Panel Should accommodate Cat6 with Rear Cable Management and Front removable Tooless Information outlet. Should have easy clip management with labels and clear label covers, Made with of Dicast Aluminium Alloy Material and Non Corrosive with Cat6 toolless RJ45 x 24 ports with color code front panel with patch cord locking. Make: Systimax/ Legrand/ Panduit |
| 283 | SITC of Cat6 UTP 23 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. Make: Systimax/ Legrand/ Panduit(1 mtr length) |
| 284 | SITC of Cat6 UTP 23 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. Make: Systimax/ Legrand/ Panduit (2 mtr length) |
| 285 | SITC of 1G-LX/LH SFP transceiver module,SMF, 1310nm, 9/125 um Single mode Fiber Type up to 20 KM. Make: Cisco/ Digisol/ Netgear |
| 286 | SITC of 6 core Single mode OS2 Unitube Armoured Optical fiber cable through existing conduit: The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. Outdoor Corrugated Steel tape Central loose tube. ( Standard Approved: ISO 11801 2nd edition/ EN 50173-1:2002 / IEC 60794-1/IEC 60793-2-50 class B1.3 / EN 60793-2-50: class B1.3 / ITU Recommendation G.652.D - the oder ITU designations A, B and C are also fulfilled / OS1/ISO/IEC 24702:2006, cat. OS2; also OS1 requirements are fulfilled/IEEE 802.3 - 2002 incl. 802.3ae ) Jacket. Make: Systimax/ Legrand/ Panduit |
| 287 | SITC of OFC Patch Cor, SM (OS2), Duplex LC-SC, LC-LC PC Type, 3M, LSZH Fiber Optic Single Mode OS2 Patch Cords are offered in LSZH Jackets with Corning Fiber,Insertion Loss : <= 0.2 db, Max 0.3db/MTRJ: Max 0.5db Return Loss : PC>= 45db, UPC>=50db, APC>=60db. Make: Systimax/ Legrand/ Panduit |
| 288 | SITC of 9U/500D outdoor type IP 55 Wall Mount Rack with Accessories: The rack size should be 600W x 500D, Front frame integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 including Power Distribution Unit (06/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Lengt), 1 cooling Fan(230V AC - 90 CFM, dB 42), 2nos 1U Metal Cable manager with Plastic cable loops and H/W screw. Make: Valrack/ Rittal/ Legrand |
| 289 | SITC of 9U/500D Wall Mount Rack with Accessories: The rack size should be 600W x 500D, Front frame integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 including Power Distribution Unit (06/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Lengt), 1 cooling Fan(230V AC - 90 CFM, dB 42), 2nos 1U Metal Cable manager with Plastic cable loops and H/W screw. Make:Valrack, Rittal, Legrand |
| 290 | SITC of 24 Port Layer 2 PoE+ Switch having 24 x 10/100/1000 Mbps Ethernet PoE+ ports with 4 x 1/10Gig SFP+ ports ,1 x RJ45 port console port ,Switching Capacity 128 Gbps , Throughput 96 Mpps ,MAC Address 16k , Switch should support IEEE 802.3af (15.4W) & IEEE 802.3at (30W). Total PoE power: 370W or above , Switch should support DHCP server/relay/client, DHCP snooping/option82 , Switch should support Console, Telnet, SSH v1/2, HTTP, HTTPS, SNMP v1/v2/v3, RMON , TFTP, FTP, SFTP, NTP, ZTP, SPAN, RSPAN,Switch should support support ICMPv6, DHCPv6, ACLv6 ,IPV6 Telnet ,Temperature 0°C -50°C ,Power Supply AC: 100-240V. Make: Digisol, Cisco, HP |
| 291 | PA SYSTEM |
| 292 | Supply of 20 Watt outdoor Horn Speaker, IP65, Frequency Response : 150 Hz – 15 kHz, 4 INCH DRIVER, peak power handling capacity 80W, Should have Passive 350 Hz high-pass filter built-in, SPL : 133 dB peak @ 1.4 kHz, IP-65 rating per IEC529, Coverage Pattern: 60° horizontal by 80° vertical , Maximum SPL (1m): 109dB peak, 8 ohm Impedence, Transformer Taps: 70V/100V: 20W, 100V: 30 w.MAKE:Bose/EV/Audac(HS121)/Sonodyne |
| 293 | Supplying, installing, testing and commissioning of quad channel Power amplifier of continous power 4x 240 W @8 ohm and 100V, frequency response- 50Hz-20 kHz , class D amplifier.The amplifier should be clean reliable audio for public address amplification and music.Line input less than 1 volt, unbalanced& line output less than 1 volt unbalanced.Make-Bose/Audac(PMQ240)/EV/Sonodyne |
| 294 | Supply of 30 W weather proof rock speaker with LMT, IP65 , Transformer Taps: 70V/100V: 20W, 100V: 30 w Make-Sonodyne (RS 650)/Bose/EV/Audac |
| 295 | Supply of 10-Channel Mixing Console: Max. 4 Mic / 10 Line Inputs (2 mono + 1 stereo) / 4 GROUP Buses + 1 Stereo Bus / 4 AUX (incl. FX),16-Channel Mixing Console mic preamps with an inverted Darlington circuit,1-Knob compressors,High-grade effects: SPX with 24 programs,24-bit/192kHz 2in/2out USB Audio functions,Works with the iPad (2 or later) through the Apple iPad Camera Connection Kit / Lightning to USB Camera Adapter,Includes Cubase AI DAW software download version,PAD switch on mono inputs,+48V phantom power,XLR balanced outputs with provision for bluetooth.Make-Yamaha/Soundcraft/Studiomaster |
| 296 | SITC of 17U 600/650D UL Listed Floor mount Rack with Front perforated door with 3 point lock, Rear mesh door with Cam lock and 3inch Castor Wheel included with 2 no 6/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Length, 4nos 1U Metal Cable manager with Plastic cable loops, 2nos CFM FAN set, 1no Monitor Tray - Ventilation - 495W - 375D and H/W screw920sets). Make: Valrack/ Rittal/ Legrand |
| 297 | Speaker Cable Armoured 2 core 2.5 sqmm PVC Sheathed etc complete as required. |
| 298 | Laying of cable (Digging , laying and refilling with sand and Bricks) |
| 299 | Installation of all equipment, testing and commissioning of the system |
| 300 | AIR CONDITIONER SPLIT |
| 301 | Supply,installation, testing and commissioning of Air Cooled HI Wall split type Air conditioners complete with Indoor unit (IDU), Out door unit (ODU), i/c R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cut off and50 hz ,1 phase AC Supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll /rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS694 or IS 9968 temperature sensing control IS/ International Electro technical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per IS :1391 Part II 2023. The system shall be able to operate up to 50 Degree C (out door ambient temperature). The indoor outdoor must be Blue Fin coated. The unit price included with 3mtr Copper piping with insulation, drain Pipe and copper Power cable. The indoor should have 4 way swing . |
| 302 | 1.5 TR with 5 Star BEE Rating (LG-AS-Q20JWZE/ O General-ASGG18CGWA-B/ Daikin-FTKU50XV16) |
| 303 | 2.0 TR with 5 Star BEE Rating (O General-ASGG24CGWA-B/ Daikin-FTKM60XV16) |
| 304 | REFRIGRANT PIPING |
| 305 | Supply,installation of hard/soft ISI marked copper refrigerant piping of size 5/8 inch and 1/4 inch for suction and liquid line with 3 corex4 sqmm FRLS Copper control cable alongwith 25 mm weather proof closed cell nitrile insulation ,complete with fitting of bends and other nesessary material to complete the job. |
| 306 | 1 TR to 3 TR high wall split A.C |
| 307 | Supply & Installation of interconnecting following sizes of refrigerant copper pipe work of following outer diameter, insulated with 25mm thick closed cell electrometric Nitrile rubber tubular insulation between each set of indoor & outdoor units . The pipe dia upto 25 shall be soft seamless & above 25mm dia shall be hard seamless . All piping inside the room shall be properly fixed/supported with suitable size of clamp/ M.S. hanger and all external piping shall run in GI. cable tray etc. as reqd. Make of insulation-K Flex/Armacell/Vidoflex/Eurobatex/Isoline Make of pipe-Rajco/Mandev/Maxflow (for 4 TR CASSETTE ac) |
| 308 | 9.5 mm with 0.8 mm thick |
| 309 | 15.9 mm with 1.00 mm thick |
| 310 | FRAME WORK |
| 311 | Supply,installation & fabrication of MS base frame for outdoor unit and other nesessary material to complete the job. |
| 312 | 1 TR to 3 TR high wall split A.C |
| 313 | DRAIN PIPING |
| 314 | Supply,installation & fabrication of Insulated drain water piping from indoor to nearestdrain point separate to all and other nesessary material to complete the job. |
| 315 | 25mm nom. Dia pipe |
| 316 | Supply and fixing of 4kVA Voltage stabilizer (Make-V-Guard/Microtek |
| 317 | Supply and fixing of 5kVA Voltage stabilizer (Make-V-Guard/Microtek |
| 318 | FIRE SAFETY EQUIPEMENT |
| 319 | Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S cylindrical body, squeeze lever dischange valve fitted with pressure indicating gauge internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS : 2878 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.Make- Safex/Supremex/ Ceasefire/Flameklog/Kalpex .4.5 kg capacity |
| 320 | Providing and fixing ABC type fire extinguishers consisting of welded M.S cylindrical body, squeeze lever dischange valve fitted with pressure indicating gauge internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.Make- Safex/Supremex/ Ceasefire/Flameklog/Kalpex .6 kg capacity |
| 321 | SIGNAGES: SITC of flexyl Photoluminescent based Glow-in-the-dark sheeting with luminious properties enclosed in a weather-proof UV stabilized film with UV screen printing by imported inks pasted over 3 mm Thick Cast Acrylic Sheet with the Protection of 3 mm Thick Cast Acrylic from Front side with stud type mirror screw with lifespan of 5 years, visible upto 4-6 hrs in total darkness for floor indication, fire exit, hydrant, hose reel, fire extinguisher, MCP, fire alarm panel, in case of fire, lift, alarm valve signages |
| 322 | Supply, installation, testing and commissioning of double sided visible LED illuminated Exit Indication Sign(300 mmx 150 mm, letter height minimum 150 mm) complete with directional arrow legend, rechargeable maintenance-free battery backup capable of providing continuous illumination for not less than 90 minutes upon mains failure, automatic charger circuit, fire-retardant ABS housing, polycarbonate diffuser, minimum letter height 150 mm, suitable for 230V AC supply, wall/ceiling mounting arrangement, complete with all accessories, wiring connections, testing and commissioning as required. The equipment shall comply with applicable requirements of NFPA 101, NFPA 70 and UL 924 standards.The Exit Indication Sign shall be a self-contained, LED-illuminated unit with integrated rechargeable battery backup, directional arrow (left, right, or straight), and automatic changeover circuitry. The sign shall operate in maintained mode (continuously illuminated) or non-maintained mode as specified, and shall automatically switch to battery power upon mains failure. The pictogram shall comply with ISO 7010 (E001 / E002 green running-man symbol) as mandated by NBC 2016 and IBC 2021. Make-Bajaj/Prolite |
| 323 | 82.5 KVA DG |
| 324 | Supply, Transportation, erection, testing and commissioning of 3 Phase, 415V, 50Hz, water cooled multi cylinder diesel generator set with alternator of 82.5KVA ( Make -Kirloskar / Jakson/TMTL/Mahindra/Captiva/Sterling) out put contineous rating directly coupled Engine and Alternator with g 82.5uard and mounted on a common base plate of Robust construction and complete with AMF panel having IP-52 protection, Acoustic Enclosure as per CPCB IV+ norms , sound absorbing material, to restrict sound level up to 75 dB up to 1 mtr distance and as per CPCB IV+ norms etc as per following specifications mentioned below. Warrentee period must be 2 years ALTERNATOR:The alternator of the output rating shall be 3 Phase, 415V, 50Hz, Ac , 0.8 P.F. lagging at 1500 RPM. The alternator is self excited, self regulated, and shall confirm to IS: 13364 of 1992 with regulation of +5% from no load to full load. degree of protections shall be IP21.ENGINE: Diesel Engine start, developing suitable BHP output at 1500 RPM with mechanical / electronic governing so as to enable the alternator to give 82.5KVA continuous output at 0.8 P.F. lagging at NTP conditions. The diesel engine shall be capable of providing 10% O/L for 1 Hr for every 12 Hrs of continuous running at full load. The engine with 1st filling of oil and Diesel etc.01. Exhaust pipe of required size and length with insulation or clading.02. Diesel tank suitable for 8 to 10 Hours running capacity.03. Residential Silencer.04. SMF Batteries with leads as per the Manufacturer standardsAMF PANEL: Cubical, Compartmentalized, AMF Panel Baord with all Power & Control Contractors, Switches, Meters and other accessories, Internal Wiring, connection, inter-connection etc. for Trouble Free smooth function for 82.5 KVA DG Set complete with Battery Charger & leads as required. BASE PLATE: Common Base Plate of required size for mounting of Engine Alternator Set fabricated from MS Channel and vibration damping arrangement with cushy foor mounting including paintng etc. as required. FOUNDATION: Suitable size Cement Concrete (1:2:4) foundation duly plastered and finished with neat coat Cement as required along with smoke exhaust system piping including base frame of structure & lightening protection system. , control cable of 15mtr 2.5sqmm 6core , civil foundation work. (The Manufacturing of DG set shall not in any case be more than six months old from the date of award of work) |
| 325 | LIGHTENING PROTECTION SYSTEM--- Lightning Protection :- Supply of 8 mm Aluminum Round Conductor.Tested as per IEC 62561. as per direction of engineer in charge.Make-OBO/Dehn/ABB |
| 326 | Supply of Roof conductor holder for parapet- PolyamideConductor holder:With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance.Tested as per IEC 62561. as per direction of engineer in charge.Make-OBO/Dehn/ABB |
| 327 | Supply of Polyamide roof cable holder for flat roof:DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance. Tested as per IEC 62561. Make-OBO/Dehn/ABB |
| 328 | Supply of Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Tested as per IEC 62561.(2nos/expansion piece ).Make-OBO/Dehn/ABB |
| 329 | Supply of 1 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305. Tested for Electrical , mechanical and chemical as per IEC 62561. Tested for 100kA lightning current. Make-OBO/Dehn/ABB |
| 330 | Supply of Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 2 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. Tested as per IEC 62561. Make-OBO/Dehn/ ABB |
| 331 | Supply for Providing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete and clamp tested upto 100KA lightning current . Make-OBO/Dehn/ABB |
| 332 | Supply for Providing of Stand for Fang Fix system 16 kg made up of frost resistant concrete. Make-OBO/Dehn/ABB |
| 333 | Supply of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by 30x3 mm GI strip as specified in drawing and directed by Engineer.Tested for 100kA lightning current. Make-OBO/Dehn/ABB |
| 334 | Supply of IP 66 Poly Propylene Junction Box. Installation at 1Mtr Height For Test Joint .Internal dimensions: 100x100x48 mm Make-OBO/Dehn/ABB |
| 335 | Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized. Tested as per IEC 62561. Make-OBO/Dehn/ABB |
| 336 | Supply for Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. Tested for 100kA lightning current. Make-OBO/Dehn/ABB |
| 337 | Supply of flat conductor holder- Fit: FL 30, With mounting hole 6.2 x 22 mm, With 2 cylinder bolts M6 x 16 and over-piece from hot-dip galvanised steel, Bottom section from polyamide, black. Tested as per IEC 62561. Make-OBO/Dehn/ABB |
| 338 | Supply for Providing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric. Make-OBO/Dehn/ABB |
| 339 | Supply of UL Listed maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 17.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 Make-OBO/Dehn/ABB |
| 340 | Supply of universal clamp made of SS to connect rod with flat conductor Make-OBO/Dehn/ABB |
| 341 | Supply of Earth conductivity enhancing mineral compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested Make-OBO/Dehn/ABB |
| 342 | Supply of The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system Make-OBO/Dehn/ABB |
| 343 | Installation of The above arrangements including all accessories as per Direction of Engg. In charge. |
| 344 | Plumbing works |
| 345 | Supplying, installing, fixing, jointing, testing and commissioning of approved make. Chlorinated Polyvinyl Chloride pipes (CPVC) SDR.11 pipes confirming to ASTM standards with necessary fittings for inetrnal toilet water supply upto 50 dia , and above 50mm dia pipe schedule 40 with fitting shall be schedule 80 ASTM IPS. The fittings and specials such as tees, elbows,couplers, bends, enlargers etc.,m with CPVC brass threaded combination / transition specials such as male adapters brass threaded female adapters, brass FPT Tee, Brass FPT elbow etc., where connection with metal is to be made including necessary drilling holes, chasing walls and making the same good in cement martor 1:1 restore the same original condition neately as directed by the Engineer in-charge. Joints to be made with CPVC solvent cement up to 50mm dia as per ASTM D-2846 and above 50mm dia primer P-70, and solvent confirming to ASTM F-4931 / 724 All exposed pipe shall be painted with latex paint. (for shafts, basement ceiling ringmain Terrace & PRM).The rate shall include necessary GI supports, GI grip bolts, angle brackets, hangers, supports as with suitable GI U-clamps, bolts, nuts and washers etc., The clamps shall be painted with two coats of enamel (approved) paint over a coat of primer etc., complete. Make:- Supreme/Ashirbad/Astral or Equivalent |
| 346 | All Floor |
| 347 | 20 mm dia C-PVC PIPE SDR.11 |
| 348 | 25 mm dia C-PVC PIPE SDR.11 |
| 349 | 32 mm dia C-PVC PIPE SDR.11 |
| 350 | supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking G.I. Pipes and fittings/ P.V.C. pipes and fittings etc. all complete as per P.H. specification and direction of Engineer-in-charge. 250 mm thick wall |
| 351 | Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking G.I./P.V.C. pipes and making good the damages as per direction of the E.I.C. |
| 352 | Supplying all materials, labour, T&P and cutting hole in R.C.C floors, roofs, etc upto 19 cm thick for passing G.I. Pipes / P.V.C pipes and fittings etc and repairing the holes after insertion of pipes etc with cement concrete (1:2:4 ) including finishing complete so as to make it leak proof as per direction of the Engineer-in-charge. |
| 353 | Supplying all materials, labour, T&P and fixing the following vitreous china Wash Water Closet & cistern fitting (European type W.C. pan) of SLS-WHT-6751S220PPZ (Make: Jaquar) with integral 'p' or 's' trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing etc all complete as per specification and direction of the Engineer-In-Charge. |
| 354 | Supplying all materials, labour, T&P and fixing Health Faucet of Jaquar ALD-CHR-577 complete with Chromium plated brass brackets fixed to wooden plugs with Chromium plated brass screws as per specification and direction of the Engineer-In-Charge. |
| 355 | Supplying all materials, labour, T&P and fixing standard sized two way Bib cock of Jaquar FLP-CHR-5041PM of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Er-in-charge. 15mm dia CP Two way bib cock with Flange. |
| 356 | Supplying all materials, labour, T&P and fixing vitreous (Orissa pattern with Cistern squatting pan conforming to IS:2556-part-3-2004) duly embedded in cement concrete (1:5:10) using 4cm size hard granite metal including fixing a pair of vitreous china 250mm x 130mm x 30mm footrest, fixing 100mm dia HCI ‘P’ or ‘S’ trap (with/without 50mm dia horn) for water closet squatting pan including jointing the trap with pan in cement mortar (1:1), cutting the floor and mending good the damages etc all complete as per specification and direction of the Engineer in charge. (MAKE-JAQUAR/HINDWARE OR EQUIVALENT) |
| 357 | Supplying all materials, labour, T&P and fixing standard sized Bib cock of Jaquar COP-CHR-037NPM etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Er-in-charge. 15mm dia CP Two way bib cock with Flange. |
| 358 | Supplying all materials, labour T&P and fixing of Under Counter wash basins with bottle trap & cp fittings of jaquar FNS-WHT-40701 of approved make in all floor of approved quality including cutting the walls & floor and making good the damags with cement concrete e.t.c including all tsxes,duties,transportation e.t.c. All complete as per specification and direction of the Engineer-In-Charge.(Size: 560x430x195 mm) |
| 359 | Supplying all materials, labour T&P and fixing HALF Pedestal type wash basins of Jaquar ARS-WHT-39305 with hole for pillar taps with cast iron or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, etc all complete as per specification and direction of the Engineer-In-Charge. |
| 360 | Matrix Set-1 (WB 65X35 with one pair mounting brackets, EWC & cistern complete with fittings & seat cover, one no hinged rail 76 cm and five nos of grab rail 60cm) Make-jaquar,(Size- 390 x 365 x 540, S TRAP) cm ,Cat No-jaquar CNS-WHT-551S & Cistern complete with fittings & seat cover,Wash Basin : 46 x 36 cm, one no. hinged rail 76 cm & 4 nos. of grab rails 60 cm. |
| 361 | Supplying all materials, labour, T&P and fixing standard sized pillar cock of Jaquar FLP-CHR-5011PM of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. 15mm dia brass pillar cock. |
| 362 | Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm thick A.C.sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of the Engineer-in-charge. Swivel Mirror Rectangular Shape(630x450).(MAKE-JAQUAR/HINDWARE OR EQUIVALENT) |
| 363 | Supplying all materials, labour, T&P and fixing standard sized Chromium Plated Glass Shelf of jaquar AKP-35771P complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge. |
| 364 | Supplying all materials, labour T&P and fixing OF W.C. BRUSH HOLDER of Jaquar ACN-1143N etc complete including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 365 | Supplying all materials, labour, T&P and fixing standard sized Chromium Plated soap case Jaquar ACN-CHR-1131N complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge. |
| 366 | Supplying all materials, labour, T&P and fixing standard sized Chromium Plated brass towel ring of jaquar ACN-1121BN complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge. |
| 367 | Supplying all materials, labour, T&P and fixing standard sized Chromium Plated brass towel rail of Jaquar ACN-CHR-1111SM complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge. |
| 368 | Supplying, installing, testing and commissioning of approved make White Viterous urinals 3.8 LPM supported by CI/MS bracket duly painted, including CP brass waste with dome type grating, CP cast brass bottle trap with extension piece, wall flanges, automatic flushing systems for urinal to ensure flusing only immediately after use, comprising of all plumbing, electronic and electrical items. CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, infrared photo cells (Sensor), eyes electrically operated solenoid valve, gate valve, black box and necessary wiring in conduit from solenoid value to black box and to mains etc, complete. Including necessary wall cutting/chasing and making good, as required.(MAKE-jaquar-URS-WHT-13253N) |
| 369 | Supplying all materials, labour T&P and fixing URINAL FLUSH VALVE FLV-1095NG (Make: Jaquar) of approved make Jaquar FLV-1095NG etc complete including cost of all materials complete as per PH specification and direction of Engineering-in-charge |
| 370 | Providing & Fixing granite slab with Table rubbed, edges rounded and polished of size 75x50 cm deep and 18mm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 as per direction of Er-in-charge. |
| 371 | Supplying all materials, labour, T&P and fixing standard sized Robe Hook of Jaquar ACN-CHR-1161N complete with all as per specification and direction of the Engineer in charge. |
| 372 | Supplying all materials, labour, T&P and fixing standard sized 15mm dia angular Stop cock of Jaquar FLP-CHR-5053PM of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Er-in-charge. |
| 373 | Supplying all materials, labour, T&P and fixing standard sized Chromium Plated soap dispenser Jaquar ACN-CHR-1137N complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge. |
| 374 | Supplying all materials, labour, T&P and fixing standard sized Chromium Plated Paper Holder of jaquar ACN-1153S complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge. |
| 375 | Supplying all materials, labour, T&P and fixing standard sized LONG BODY Bib cock WITH WALL FLANGE of Jaquar COP-CHR-037NPM of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Er-in-charge. 15mm dia CP Two way bib cock with Flange |
| 376 | Supplying all materials, labour, T&P and fixing standard sized Chromium Plated Shower of Jaquar OHS-CHR-1989 & Shower Arm- Jaquar-SHA-483 complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge. |
| 377 | Supplying all materials, labour, T&P and fixing standard sized Conceal Stop Cock Jaquar FLP-CHR-5083KPM & Jaqual ALD-083R fixed to wooden plugs with Chromium Plated brass screws as per specification and direction of the Engineer in charge. |
| 378 | Fixing of 20 mm dia C-PVC Ball Valve confirming to IS : 781-1995 of approved make as per specification complete as per direction of Er-in-charge. 32mm dia brass or gun metal full way valve. |
| 379 | Fixing of 25 dia C-PVC Ball Valve confirming to IS : 781-1995 of approved make as per specification complete as per direction of Er-in-charge. 20mm dia brass or gun metal full way valve. |
| 380 | Supply all materials, labour, T&P and providing fitting & fixing (Aqua guard)Aquaguard Blaze RO+UV+MTDS Water Purifier pure with water storage capacity 4 liters along with 2 nos of fancets 1 for cold water and 1 for normal water including a flow of 1.5 ltr per minute etc. all complete as per approved drawing, specification and direction of the EIC..(Make- EUREKA FORBE,LIVE PURE OR EQUIVALENT) |
| 381 | Supplying all materials, labour, T & P and constructing of Inspection chamber(IC) of the following inside size with 8 cm thick R.C.C. precast cover slab in CC (1:2:4) mix using 12mm size h.g. chips, foundation concrete (1:4:8) using 40mm size h.g. metal on bed aound trap , Fly Ash brickwork in CM (1:6) in P&F and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mm x100mm size gully trap, 150mm x150mm C.I gratig etc. all complete as per aproved drawing, specification and direction of Engineer-in-charge. |
| 382 | Size- 600 x600 mm |
| 383 | Size- 900 x800 mm |
| 384 | Providing and fixing square mouth S.W GULLY TRAP(G T) class SP-1 complete with CI grating brick masonry chamber with water tight CI cover with frame of 300X300mm size (inside),the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per the standard desifn. brick masonry chamber of size 180 X 150 mm size complete as per approved specification and direction of the Engineer in charge |
| 385 | Size- 300x300 mm |
| 386 | Supplying all materials, labour, T & P and constructing RAINWATER COLLECTION PIT chamber of the following inside size with 8 cm thick R.C.C. precast cover slab in CC (1:2:4) mix using 12mm size h.g. chips, foundation concrete (1:4:8) using 40mm size h.g. metal on bed aound trap , Fly Ash brickwork in CM (1:6) in P&F and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mm x100mm size gully trap, 150mm x150mm C.I gratig etc. all complete as per aproved drawing, specification and direction of Engineer-in-charge. |
| 387 | 450mmx4500mm with RCC cover |
| 388 | Fixing double layer cylinderical water storage tanks conforming to IS: 12701--1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc, including hoisting upto a height and placing the tank to the required position etc all complete as per specification and direction of the engineer in charge.DOUBLE LAYER 2000 LIT. CPVC TANK ,(Make- Astral,Supreem or Equivalent.) |
| 389 | Supplying, fixing and testing PVC soil, waste, Rain and vent pipes (SWR) supreme confirming to IS13592 : 2013, type B with rubber ring/Solvent (confirming toIS5382) joint inclusive of allnecessary specials like bends, tees,offsets, door bends, junctions, cowls, etc.,laid underfloor/ fixed on walls,and in pipe shafts etc., complete.The rate shall include necessary GI supports, GI grip bolts, angle brackets, hangers, supports as with suitable GI U-clamps, bolts, nuts and washers etc., The clamps shall be painted with two coats of enamel (approved) paint over a coat of primer etc., complete. Make:- Supreme/Ashirbad/Astral or Equivalent |
| 390 | 40 mm dia . |
| 391 | 50 mm dia . |
| 392 | 75 mm dia . |
| 393 | 110 mm dia . |
| 394 | 110 mm dia Rain pipe. |
| 395 | Supplying, fixing and testing PVC floor trap with SS frame and cover 75mm dia outlet fixed on a bed of cement concrete with (Heavy duty type) etc., complete. Make:- Supreme/Ashirbad/Astral or Equivalent 40mm x 75 mm dia |
| 396 | Supplying, fixing and testing PVC Nahani trap with SS frame and cover 75mm dia outlet fixed on a bed of cement concrete with (Heavy duty type) etc., complete. Make:- Supreme/Ashirbad/Astral or Equivalent |
| 397 | Providing ,fixing , testing and commissioning of approved make PVC vent cowl with necessary accessories etc., complete. Make:- Supreme/Ashirbad/Astral or Equivalent 75mm |
| 398 | 110 mm dia |
| 399 | Providing ,fixing , testing and commissioning of approved make PVC CLEAN OUT PLUG with necessary accessories etc., complete. Make:- Supreme/Ashirbad/Astral or Equivalent |
| 400 | 75 mm dia |
| 401 | 110 mm dia |
| 402 | Supplying all materials, labours,T&p and laying trenches (to level or slope) unplasticized P.V.C pipe conforming to IS4985/2016 of the following out side dia for pressure rating PN-6 including jointing with supply of approved solvent cement by non-heat application method/as per manufacture's specification,providing and laying in trench cement concrete(1:4:8) with 40 mm size hard granite metal in the type C-1 standard bedding surrounding or encasing including concrete for bedding and curing e.t.c all complete as per P.H specification and direction of the Engineer in charge Make:- Supreme/Ashirbad/Astral or Equivalent |
| 403 | 160 mm dia U-PVC pipe with al-round concreteing |
| 404 | 200 mm dia U-PVC pipe with al-round concreteing |
| 405 | Recharge pit (7 nos) providing and filling filter media |
| 406 | 40mm Metal H.B.H.G-- 4.0x2.50x0.3= |
| 407 | 20mm Metal H.B.H.G- 4 x 2.5 x 0.3 |
| 408 | Coarse sand- 4 x 2.5 x 0.3 |
| 409 | 450x450mm Square Man Hole Cover -50.0kg |
| 410 | Sinking of tube well(200) for PIT |
| 411 | Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories, tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (G.I/ P.V.C/ M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well), 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore only |
| 412 | Drilling of 200mm dia bore |
| 413 | 00 mtr to 30mtr |
| 414 | Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity from ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and slotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials. |
| 415 | Lowering of 160 mm dia PVC pipe |
| 416 | Cost of 160 mm pvc pipe |
| 417 | Cutting slot in sloted pipe in rain water |
| 418 | Labour for packing gravel outside the tube well |
| 419 | Cost of washed gravel |
| 420 | Borewell (2 nos) |
| 421 | Construction of 2 nos production wells including scientific source finding through consolidated and unconsolidated rock with down the hamer drilling rig or combination rig with pvc pipe and installation of submersible pump set with all acessories |
| 422 | Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the engineer in charge including use of own rig with its accessories ,tools and plant and consumables etc for lowering of 200mm/150mm dia G.I.P.V C/M.S casing pipes for housing fitted with socket and with or without well screen as for the necessity for soft ,medium,hard and boulder formation( G.I/P.V.C/M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well) 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore only |
| 423 | Drilling of 200mm dia bore (2 nos ) |
| 424 | Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity form ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and dotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials |
| 425 | Lowering of 150mm dia P V C casing pipes |
| 426 | Supplying polyvinyl chloride pipes as per ASTM-D-1785-89 having threads in accordance with DIN 2999 part-1/DIN-42225 PART-II specification length of pipe (laying length) will be 3 mtrs.The pipes shall be supplied with both external threaded with free socket. The pipe having external thread at one end i.e. female & or belled end . The female end having internal thread is to be belled in order to accept the male end while jointing pipes with a bore threading shall be provided with a greave at the roof of the male thread accomodate flexible PVC/Rubber 'O' ring to make the joint water tight color of the pipe shall be blue The name of the manufacture along with batch.No class of pipe shall be stranded legibly of each pipe length |
| 427 | 150mm dia PVC (sch-80) pipe (As Per SoR -2022) |
| 428 | Supplying all materials, labour, T & P and providing sanitary sealing by cement concrete grouting of annular space around GI/PVC/MS housing pipe upto 5m below ground level (as per drawing) to plug the bore hole excluding cost of cement all com |
| 429 | Cleaning & developing the tube well with supply of compressor worked till clear & adequqte discharge is obtained from the tube well including supply & use of all necessary equipment & labour as per directin of the Engineer in charge |
| 430 | By DTH Rig |
| 431 | Supplying all materials, equipments,labour & conducting reconnaissance survey , integrated Hydrological & Geophysical (Electrical resistivity Method) survey & selection of potential source for exploration of ground water including selection & recommend |
| 432 | Rocky terrain with boulder formation for 300m depth |
| 433 | Supplying all materials, labours, T&P and providing fitting & fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase /1 phase line voltage ranging from 320 volt to 450 volt conforming to Si 8034/89 with following specifications with suitable control panel ,jointing with GI/PVC/HDPE pipes,electrification,testing, commissioning ,trial running, conveyance of all materials to worksite , payment of taxex etc all complete as per specification & direction of the Engineer in charge (Texmo/crompton Greaves/ Kirloskar make) |
| 434 | 2HP Single phase 3 stage vertical/Horizontal submersible pump set at head renge of 30 to 54 mtr with discharge capacity 155 to 110 L P.M with outlet dia 32mm |
| 435 | Dol Control panel |
| 436 | 40mm dia steel short piece |
| 437 | Well cap |
| 438 | 50mm size CI bracket |
| 439 | 25 sqmm flat cable |
| 440 | 20 mm dia rigid UPVC pipes |
| 441 | Steel ropes with cover |
| 442 | Supplying all materials ,labour, T&P and providing and fixing to wall or celling and floor HDPE pipes and pipe fiting conforming to IS: 4984/2000(10KGF/SQCM) of the following nominal bore with clamps & joining by Fusion welding method including testing making good the wall celling & floor all complete as per specificaations 7 direction of the engineer in charge |
| 443 | 32mm dia HDPE pipe |
| 444 | Borewell Chamber. |
| 445 | Earth work in excavation of foundation in all kinds of soil within 50m initial lead and 1.5m initial lift including rough dressing & breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth and as per direction of the engineer-in-charge.1.20x1.20x0.40= |
| 446 | Supplying all matrials, labour, T&P and filling in foundation and plinth with sand well watered and rammed including conveyance of all complete as per direction of the engineer in charge. |
| 447 | Supplying all materials, labour, T&P and providing cement concrete (1:3:6) with 4cm size hard granite metal including watering , curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the engineer in charge. In ground floor 1.20x1.2x0.15= |
| 448 | Supplying all matrials, labour, T&P and providing brick work with fly ash brick having crushing strength not less than 75kg/cm2 with dimensional tolerance 8 percent in cement mortar (1:6) including watering , curing, conveyance of all materials to worksite, payment of royalty, taxec etc all complete as per specification and direction of the engineer incharge. In F&P 2(1.15+0.65)X1.00X0.25= |
| 449 | Supplying all materials, labour, T&P and providing M.S reinforcement for R.C.C work including cutting, bending, binding, and trying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the engineer in charge. In ground floor. |
| 450 | R.C.C. M-25 grade with 20mm and down grade C.B. chips of approved quality from approved quarry including hoisting, laying hire charges of concrete mixture, vibrator, watering, curing and cost of all materials and labour, centering shuttering etc complete but excluding cost of reinforcement. In ground floor. |
| 451 | Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard brocken granite chips including watering, curing , conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the engineer in charge. In ground floor. |
| 452 | Supplying all maerials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including watering , curing, conveyance of all materials to worksite, payment of royalty, taxes etc all materials to worksite,payment of royalty, taxes etc all complete as per specification and direction of the engineer in charge. In ground floor (inside/outside) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysOct 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender