Tender For Renovation Of Electrical Installation At The Office Building With Illumination At The Site Of Kalyani Fish Farm Kalyani, District Of Nadia.
Tender Value
40.64 Lakhs
Estimated cost
Bid Submission
30 Nov 2026
34 days left
EMD
81295
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
24 Paraganas North → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Electrical Installation At The Office Building With Illumination At The Site Of Kalyani Fish Farm Kalyani, District Of Nadia.
BOQ
| Sl. No. | Item Description |
| 1 | Dismanting the existing electrical accessories, such as all kinds of old wiring battens woodden blocks, conduit pipes, main switchs, switchboard, ICDBs, light fittings, power boards, different size etc, at the working site and depositing the dismantied items at the store with mending the damages as per the directions. |
| 2 | Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) partly in 20mm size PVC rigid conduit 'FR' (Precision make) [for ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for horizontal & vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board on wall complete with 2 no. “Ph & N” copper bar incl. bakelite/ Perspex top cover 3 mm thick and incl. 175x100x65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finish [only PVC Rigid Conduit on ceiling and remaining portion concealed]Average run 8 mtr |
| 3 | Distribution wiring in 2 x 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make), with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board cum JB on wall complete with 2 no. suitable size “Ph & N” copper bar incl. bakelite/Perspex (wall matching color) top cover 3 mm thick and incl. 175mmx100mmx65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finishAverage run 8 mtr |
| 4 | Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 5A 3 pin plug point incl. S&F 240 V 5A 3 pin flush type plug socket & piano key type switch (Anchor make) incl. S&F earth continuity wire, fixed on sheet metal (16 SWG) switch board with bakelite/perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to original finishOn board |
| 5 | Supply & Fixing 240 V, 6A, plug socket with separate 6 A Piano key type switch (Brand approved by EIC) on sheetmetal switch board embedded in wall incl. S & F150x100x65mm MS (16SWG) switch board andbakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required. |
| 6 | Supply & Fixing 240 V, 6A plug socket (Brand approved by EIC), without switch & plug top, on existing sheet metal switch board wit bakelite/perspex top cover by screws after making housing for plug by cutting bakelite/perspex top cover and making necy. connections with PVC wire and earth continuity wire etc. |
| 7 | Supplying & Fixing CRC sheet metal (16 SWG) JB-cum-Switch Board of the following sizes complete with three no. suitable size Copper bar with holes (for Ph, N & E) fixed on bakelite/Hard Rubber insulator over the MS welded chairs incl. bakelite/Perspex/coloured Perspex (wall matching colour) top cover 3 mm thick flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works175 mm x 100 mm x 65 mm |
| 8 | Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required |
| 9 | Supply & Fixing 240 V, 3 nos. 6A, & 1 no. 20A plug socket with separate 3 nos. 6 A & 1 no. 20A Piano key type switch with indicator & 16A kit-kat flush type fuse (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 240x200x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required |
| 10 | Supply & Fixing 240 V, 20 A Piano key type switch(Brand approved by EIC) on sheet metal switch board incl. S & F 100x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cuttingbakelite/perspex cover and making necessaryconnections as required |
| 11 | Supply & Fixing 240 V, 25 A, Modular type starter (Brand approved by EIC) with 25A Modular switch type DP MCB (CCurve) and 4 Module GI Modular type switch board with 4 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 12 | Supplying and fixing 415V, TPN SFU with sheetsteel enclosure on flat iron/angle iron frame on wallwith nuts bolts etc incl. S & F 3 nos. DIN type HRCfuse as per rating.125 Amp (Make-Havells/L&T/Siemens) |
| 13 | Supplying and fixing 415V, TPN on load frontoperated Changeover switch with Sheet Steelenclosure on angle iron frame on wall with nutsbolts etc125 Amp (Make-Havells/L&T/Standard) |
| 14 | Supplying and fixing double door Vertical TPN MCBDistribution board for MCCB incomer with IP-42/43protection, on angle iron frame on wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment8 Way up to 160 Amp. Make-ABB/Legrand/Seimens. |
| 15 | Supplying and fixing 415 V Four Pole MCCB ofBreaking capacity 25kA/35kA with fixed thermaland fixed magnetic / adjustable thermal and fixedmagnetic setting in existing DBs / enclosure andnecessary connection160 Amp |
| 16 | Supplying and fixing double door Horizontal TPN MCBDistribution board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment4 way. (Make-Seimenes/L&T/Legrand) |
| 17 | Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthingattachment.2+6 way (Make-Seiemens/ABB/Legrand) |
| 18 | 2+10 way |
| 19 | Supplying and fixing MCB SS enclosure with IP-20/30 protection, powder coated provision for two/four pole MCB, concealed in wall after cutting the wall & mending good the damages to original finish incl. painting, connection & provision for earthing attachment2 way (Make-Legrand/ABB/Seiemens) |
| 20 | 4 way (Make-Legrand/ABB/Seiemens) |
| 21 | Supply, delivery & installation of 240 V, 12 way dpuble door SS encloser, powder coated , IP-43 protaction MCB DB as a timer DB with neutral bar, Din Rail comprising with 1 no 20/25 A DP MCB (C' Curve, 10 KA), 1 no 24 hour digital Time switch , 1 no 20/25 A 2 pole contactor (Make-ABB/Schneider/ Legrand) with internal wiring by 2.5/4/6 sqmm sigle core strandd 'FR' PVC insulated & unsheathed copper wire (Make- Finolex/Havells/ RR Cable) includind 1 no Auto Manual bypass Toggle switch provision for earthing attachment LED indication light on the on-off condition. (For Compound Light/ RAC) |
| 22 | S & F of 415 V, 4 way, double door, IP-43 protection . HTPN MCB DB ( Make-Legrand/ ABB/ Schneider/ Siemens) with DIN RAIL concealed/ Surface in/on the wall, mending well the damages to original finish as a three phase timer DB comorising with 1 no. 415 V, 63 A FP MCB (C-cURVE, 10 KA), 1 no 24- hour programmable Time Switch with a minimum switch time of 15 minites, 1 no 415 v, 63 A, 3 pole contactor FP 63 A terminal block, 1 no Auto manual bypass Toggle Switch 2 no s ON-OFF indication LED light complete with internal wiring by required sizes single core stranded 'FR' PVC insulated & unsheated copper wire ( Make- Finolex/Havells/RR-Kable), including provision for netural link & earthing attechment ( Make of MCB, Time switch and Contactor would be the same as per the required. |
| 23 | Supplying and fixing sheet steel (16SWG) cable end box on 125 Amp TPN SFU enclosure with nuts bolts etc incl. powder coated painting. |
| 24 | Supplying and fixing double door sheet steel (16SWG), powder coated cable end box for 8 ways VTPN DB enclosure with IP-42/43 protection, on angle iron frame on wall & mending good the damages to original finish with nuts bolts etc incl. provision for earthing attachment |
| 25 | Cutting Channel of size (40 mm x 40 mm) on masonry wall by Electric operated cutting machine incl. supplying & fixing heavy gauge 19 mm, 3 mm thick Polythene pipe by means of anchoring chemical (Hilti/Sika) and GI 'U' hooks of 8 SWG incl. supplying and drawing 18 SWG GI wire as Fish wire and mending good damages to original finish by using own toolsand tackles19 mm dia 3 mm thick polythene pipe without earthcontinuity wire |
| 26 | Cutting Channel of size (43 mm x 43 mm) on masonry wall by Electric operated cutting machine incl. supplying & fixing heavy gauge 25 mm, 3 mm thick Polythene pipe by means of anchoring chemical (Hilti/Sika) and GI 'U' hooks of 8 SWG incl. supplying and drawing 18 SWG GI wire as Fish wire and mending good damages to original finish by using own tools and tackles25 mm dia 3 mm thick polythene pipe without earthcontinuity wire |
| 27 | Supplying & Fixing sheet metal inspection box (16 SWG) of the following sizes flushed in wall by housing the same after cutting brick wall incl. making earthing attachment, painting and mending good damages to building works100 mm x 100 mm x 65 mm |
| 28 | 150 mm x 100 mm x 65 mm |
| 29 | 175 mm x 100 mm x 65 mm |
| 30 | Supplying and fixing PVC Rigid Conduit 'FR' [Precision Make] on wall, ceiling with saddles and other accessories as required and mending good damages to building works20 mm size |
| 31 | 25 mm size |
| 32 | Making holes on RCC ceiling 125 mm depth having dia of following sizes :125 mm depth, 25 mm dia |
| 33 | Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Make-Finolex/RR kable/Havells) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required3 x 22/0.3 (1.5 sqmm) |
| 34 | 2x36/0.3 (2.5 sqmm) + 1x22/0.3 (1.5 sqmm) as ECC |
| 35 | 2x56/0.3 (4 sqmm) + 1x36/0.3 (2.5 sqmm) as ECC |
| 36 | 2x84/0.3 (6 sqmm) + 1x56/0.3 (4 sqmm) as ECC |
| 37 | 4x126/0.4 (16 sqmm) + 2x80/0.4 (10 sqmm) as ECC |
| 38 | Supply & Fixing bakelite / perspex top cover on existing Inspection board by Brass screws100 mm x 100 mm x 65 mm |
| 39 | 150 mm x 100 mm x 65 mm |
| 40 | 175 mm x 100 mm x 65 mm |
| 41 | Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes.2 x 2.5sqmm + 1 x 1.5 sqmm |
| 42 | 2 x 4 sqmm + 1 x 2.5 sqmm |
| 43 | 2 x 6 sqmm + 1 x 4 sqmm |
| 44 | 4 x 16 sqmm + 2 x 10 sqmm |
| 45 | Supplying & Delivery 1200 mm cilling fan(make - Crompton Aura Prime Antidust/ Orient Quasar Ornamental/ Havells. |
| 46 | Supply ,delivery & fitting of box type 4 ft long single T-8 , 22 watt led Tube light. Make-Phillips/ havells/Crompton. |
| 47 | Supply ,delivery & fitting of box type 4 ft long double T-8 , 22 watt led Tube light. Make-Phillips/ havells/Crompton. |
| 48 | Supply of 4 ft long 18/20 watt polycarbonate LED T-8 Lamp. Make- Make-Phillips/ havells/Crompton. |
| 49 | Supply & delivery of 240 V, 1420 RPM , 300 mm (12'') Exhaust Fan. ( make-Havells/ Crompton/EIC). |
| 50 | Supply & delivery of 240 V, 1370 RPM , 225mm (9'' ) Exhaust Fan. ( make-Havells/ Crompton/EIC). |
| 51 | Supplying & Fixing 240 V AC/DC superior type Ding-Dong Call Bell (Anchor) on HW board incl. S&F HW board |
| 52 | Supply & Delivery of 240 V, 18 inch(450 mm) dia Full metal body wall fan. (Make-Crompton/Orient/ E.I.C). |
| 53 | Supply of 240 V, 18'' (450 mm) dia whole metal body and metal blade (4 blade) Air- circulator Pedestal Fan complete with all accessories such as regulator, cord and 3 pin Top. Make- Orient/ Havells/Crompton). |
| 54 | Supply & Delivery of LED Flood light luminarieIP 66,made up of pressure die cast aluminiumhousing with Toughened glass/ PC coverprovided with high power LEDs and secondaryoptics PClPMMA lens and Silicon filled BISregistered Potted Vibration proof Driver with builtin 4 KV surge protection and 10KV external SPDwith Efficacy> 135 lumen/watt or better, Impactresistance-IK10/IKO8,CRI >70, CCT > 5700K.Make:- Wipro ALPHA/Crompton, PLUTO NEO/ Philips Tango LED/Bajaj) Driver Mk.- Phifips Signify/Wipro/ Xitanium / Inventronics. LED Chip mk.-Nichia,Cree,Osram, Lumiled. |
| 55 | Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter:For 30 cm (12\\") Exhaust fan |
| 56 | For 23 cm (9\\") Exhaust fan |
| 57 | Supply & Fixing aluminium louver shutter on wall with necy. bolts & nuts (6 mm dia x 62 mm long)30 cm Exhaust Fan (12'') |
| 58 | 23 cm Exhaust Fan (9'') |
| 59 | Fixing only ceiling fan complete with blades, canopy, fork, rubberbush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire. |
| 60 | Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length |
| 61 | Fixing only single /twin fluorescent light fitting complete with all accessories directly on wall/ceiling/HW round block and suitable size of MS fastener |
| 62 | Fixing only single/twin fluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports fixed with “L” type MS clamp whose one side fixed on ceiling with sutable size 4 nos. fastener and other side connected with the conduit with suitable size of bolts and nuts incl. S&F EIconduit, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire and mending good damages to original finish and painting etc. by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length. |
| 63 | Extra for suspension exceeding 25 cm with S&F additional 2 no. 20 mm dia EI conduit (14 SWG) supports & necy. PVC insulated wire and painting etc. as required by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length. |
| 64 | Supply & Fixing of tube light weight and screw less linear batten with the high efficacy, extruded aluminum housing offering superior finish, long life & high transitivity polycarbonate diffuser resulting in high efficacy and uniform lighting. (make-Philips-Cat Ref-BN170C LED20S-6500 PSU L120/ Crompton Cat Ref-CCS-100-20-65-HL2 DP-NWH/ Wipro Cat No-LM34-251-XXX-2765.) on wall with HW block/MS flat (25x6mm) clamp (as per direction of EIC) and suitable size MS fastener celling plate nipples etc as required. |
| 65 | Supply & Fixing Socket type fan regulator (Step type)(Brand approved by EIC) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connections etc. |
| 66 | supply & Fixing LED aluminium bulkhead fixture is commonly used outdoor and industrial setting, IP66 rating indicates that is highly resistance to dust and water making this 10 watt LED Bulkhead suitable for outdoor installations. 120 Lm/W efficacy, 4KV in built surge protection & IK08 impact resistivity is suitable for general illumination in areas where harsh weather condition are a concern, such as parking lots, walkways, warehouses or industrial facilites light fitting on wall. (Crompton Cat No-CIS-306-10-57-SL-DP-NBK./ Philips type-WT202W LED 10S CW PSU S3 PC/ Wipro Cat. No-LW07-141-XXX-57-G1). |
| 67 | Supply & fixing 240V,16/20 A, 3 pin plug top with indicator.(Make-Anchor/Havells/EIC) |
| 68 | Supplying and fixing 415 V Four Pole MCCB ofBreaking capacity 25kA/35kA with fixed thermaland fixed magnetic / adjustable thermal and fixedmagnetic setting in existing DBs / enclosure andnecessary connection. ( Make-Legrand/ABB/L&T).125 Amp FP MCCB |
| 69 | Supplying and fixing 240/415 V MCB Isolator ondin rail of existing DBs and necessary connection.(Make-Legrand/ABB/L&T).32 A, 240 V, DP MCB Isolator. |
| 70 | 40 A, 240 V, DP MCB Isolator. |
| 71 | 63 A, 415 V, FP MCB Isolater. |
| 72 | Supplying and fixing 240/415 V MCB of Breakingcapacity 10kA & C characteristics on din rail ofexisting DBs and necessary connection6-32 A , 240 V, SP MCB |
| 73 | 32 A, 240 V, DP MCB |
| 74 | 32 A, 415 V, TP MCB |
| 75 | 63 A, 415 V, TP MCB |
| 76 | Supplying and Fixing GI water proof looping cable box having hinged GI Top Cover having 4 mm thick with rubber gasket lining, railway type mechanical locking arrangement, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one 250 V, 15 A Kit-Kat fuse unit, one NL on porcelain insulator etc. and housing the same in pole muffing incl. addition and alteration to the existing CC muffing (6:3:1) after dismantling the damaged looping cable box etc. where necy. incl. painting200x150x100mm |
| 77 | supply 7 fixing of garden light fittings (Make-Crompton-LBLA1-10-CDL/ Philips) complete with all accessories fixed at RCC base including making of suitable RCC base and making necessary connection as per direction WIC. |
| 78 | Supply & delivery of Cubical type L.T distribution panel board of require size, compartmentalized, maple arrangment having rigid & seif supporting structure fabricated from 2 mm thick CRCA sheet stee. The panel board consisting of the following switches.a.Incoming arrangement 415 V, 200 a TPN, 50 Hz SDFU in open execution type with 3 nos 200 Amp Din type HRC fuse link . (Make-Siemens/LT/Schneider).b.Bus section, 415 V, 315 A capacity electrolyting graded copper bus ber with suitable sizes Cu bar for 3 Ph & N . The bus ber shall be fixed with FRP chair & the entire bars are insulated with PVC heat Sinkable sleeve of suitable size & different coloured as per norms/ direction of EIC.c.Out going arrangement: 415 v,50 Hz, TPN,SDFU in open execution type-i) 100 Amp-2 nos, ii) 63 amp-2 nos, iii) 32 Amp-2 nos, wirh din type HRC fuse link as perrating of each SFU (Make-Simens/ABB/Schneider). All SFUs should be connected with required size/equivalent ratins solid Copper bar.d. Cable alley cable entry arrangement will be provided in the back side of the cubical panel in botton end vertical position including gland plate must be placed at the botton of the panel with detachable type as per direction of EIC and also to be provided 2 nos Bus Alley in vertical.e. Painting: The complete panel board shall be painted by 2 coats of powder coated synthetic enamel Paint over two coats of R.O primer of approved make & brand & colour as per direction of EIC.f. construction details : All incoming & outgoing panel mounted cubical Switch disconnector fuse shall be housed in Respective compartment with hinged & gasketted door at front all doors shall have panel lock arrangement . The panel shall be property Gasketted to prevent ingress of dust & moisture & Remain Bus bar will be proparty arrange & all switchs shall be fixed by M.S nuts & bolts and also all SFU/SDF units should be connected with the proper size electroliting graded tinned Cu, flat/bar/ as per direction of E.I.C.g. Installing the L.T panel in position with necessary thems required and making a small brick wall for leveling up the L.T panel such that incoming cable can be connected in proper way with out stress. |
| 79 | Excavation of soil for installation of Earth Electrode and filling & ramming.For Soft Soil |
| 80 | Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts.vlong and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below:TATA-Medium GI pipe |
| 81 | Earthing with 65 mm dia GI pipe (TATA-Medium)x 3.0 Mts. long and 1 No. 50 mm x 6 mm galvanized (Hot Dip) steel strip (4 Mts. long), 20 mm dia x 125 mm long galvanized bolt, double nuts, double washers including finishing both ends by making holes etc. and S & F 65 mm dia GI pipe (ISI-Medium) protection (3 Mts. long) to be filled with bitumen partly underthe ground level and partly above ground level to an average depth of 3.65 Mts |
| 82 | Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm withlocking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe |
| 83 | Extra for treatment of soil by using salt & charcoal or coke for plate electrode |
| 84 | Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 40 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required |
| 85 | Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc. |
| 86 | Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damagesSolid GI wire,4 No SWG |
| 87 | S & F Lightning Conductor Air Terminal made of 20 mm dia 1000 mm long GI pipe (ISI Medium) having five discharge prongs of 4 SWG GI (Hot Dip) wire at top duly soldered with 7/16 stranded GI (Hot Dip) wire and 85 mm dia 6 mm thick GI base plate at bottom incl. necessary holes etc. complete duly grouted on the parapet etc. in CC mortar ( 4:2:1) including thimble joints of 7/16 SWG wire and (25 x 6) mm GI strip with SS nuts, bolts & washers. |
| 88 | Supply & Fixing spacing insulaor (4/5 wire LT overhead Line. |
| 89 | Connecting the equipments body to earth busbar including S & F 25 mm x 6 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc. |
| 90 | Cutting cornices/ steps etc. including cutting recess in buildings etc. & supply & fixing 15 mm bore (ISI-Medium) GI pipe protection as below and mending good damages to the building works:Length upto 0.5 Mtr |
| 91 | Hiring charges for scaffolding arrangement including dismantling at the end of work and carriage, for LC installation, per storey of building per vertical run |
| 92 | Supply & Fixing of Testing Joints by 20 mm x 3 mm thick GI (Hot Dip) strip 125 mm long grouted on wall having clearance of 6 mm from wall for making connection with thimbles at the end of 7/10SWG GI (Hot Dip) stranded Wire and 4 SWG GI (Hot Dip) wire of vertical conductor and conductor from earth electrode complete with S & F thimbles, GI bolts, nuts, check-nuts, spring washers etc. as required |
| 93 | Connecting the equipments body to earth busbar incl. S & F 50 mm x 6 mm Galvanized (Hot Dip) MS flat on wall/floor with GI saddle as required and connection to equipments with incl. drilling holes, bolts, nuts,washers etc. |
| 94 | Jointing for horizantal & Vertical run of GI strips through welded joint (25x6) or (50x6)mm GI strip to Lap joints/T joints. Etc and painting the joints with 2 (two) coats of bituminous paint. (N.S) |
| 95 | Supply & Delivery of 7 mtr long G.I Tuber Pole (Make-Utkarsh/Jindal/Bansal) as per spacification type 410-SP-8, approx weight 103 kg. Outside dia thickness and length of the bottom section-139.7 mm x4.85mm x4.5 mtr. Middle section 114.3mm x3.65mm x1.5 mtr. The pole must be porovided with nut bolt for earthing attachment , holes for entering loop wire base plate (size-250mm x250mm x10mm) properly weided on bottom of the pole and pole cap on the top of the pole. |
| 96 | Erection of Single Steel tubular pole of length as given below with/without sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts.above ground level including 3 mm thick neat cemented finish and GI earth bolt after making drilled holes etc. on pole & carriage of pole upto 1.6 Km from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properlyUpto 9.0 mtr. Size 0.6x0.6x1.70 mts |
| 97 | S & F of 1.5 mtr long 50 mm dia (ISI-M) detachable type GI single arm bracket weided with pole sleeve of 100 mm dia 0.30 Mtr. Long suitable for above pole incl S&F 2 nos 150mm long 15mm dia all through nut bolt sets. Washer etc incl. painting 2 coats approved A.I paints as per directions of EIC. |
| 98 | S & F of meter long 50mm x 50mm thick M.S angle iron on the top of the ST pole with 50 mm x 5 mm thick M.S flat iron half round clamp, nus-bolts arrangement for fixing 2 nos LED flood lights after making necessary drilied holes as required size. |
| 99 | Supplying & Fixing GI waterproof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250 V 15 A kit-kat fuse unit, one NL on porcelain insulator, one compression type brass cable gland for upto 2- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosivepaint |
| 100 | Supplying and fixing polythene pipe complete with fittings as necy. under ceiling/beam, bound with 22 SWG GI binding wire incl. supplying and drawing 1x18 SWG GI Wire as fish wire inside the pipes and fittings and providing 50 mm dia disc of MS sheet (20 SWG) having colour paint at one face fastened at the load point end of the polythene pipe with fish wire (synchronizing with roof/beam casting work of building construction)32mm dia 3mm thick Polythene Pipe |
| 101 | Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required25 mm dia |
| 102 | Extra on items 1& 2 above, for providing CC (6:3:1)base block (around the pole) dimension 0.60x0.60x0.76 mt. above ground level, neatly cemented finish (3 mm thick), at the base pole (in lieu of CC muffing) incl. drilled hole in pole suitable for alkathene/polythene pipe entry, for street light wiring, without Loop Box |
| 103 | Supply & drowing of 1.1 kv grade 3 core 1.5 sqmm PVC incluated stranded cu wire through 20 mm dia 3mm thick polythene pipe from pole loop box to LED fittings. (Make-Finolex/RR cable/Hevells). |
| 104 | Supply of 240 volt out door type LED Industrial street light fitting/luminare having bthe the following minimum input power IP 66 protected. Minimum luminous efficacy 140 watt (NABL LM 79 Certified from OEM) & COLOUR TEMP 5700 k with 10 KV SPD, complete with all accesories. (Make-Philips urban Edge Plus/K-Light/Wipro/Havells).60 Watt |
| 105 | 70 Watt |
| 106 | 120 Watt |
| 107 | Supply of 240 volt out door type LED Flood light fitting/luminare IP-66 protected, wide beam PDC housing high impact resistance (IK-07), glass cover optice,Minimum luminous efficacy 120 Im/watt colour temp,5700 K with 10KV SPD, complete with all accesories. (Make-Philips Field Star type-BVP282 LED 120 CW FGSYSWB 100 SDP VI/K-Light/Wipro/Havells). |
| 108 | Fixing only outdoor / street light type fluorescent light fitting or MV light fitting complete with all accessories to be fixed /projected from the wall of the building incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 40 mm GI pipe(ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc. |
| 109 | Fixing only Floodlight Fitting with suitable tie clamps and MS plate for mounting on Pole/Tower or similar structure. |
| 110 | Supply & delivery of the flowing sizes 1.1 KV grade 3/4 core XLPE Insulated Aluminum Conductor Armored Cable.(Make-Havells/RR-Cable/Polycabe/KEI.3 core 6 sqmm cable |
| 111 | 4 core 10 sqmm cable |
| 112 | 4 core 16 sqmm cable |
| 113 | 4 core 25 sqmm cable |
| 114 | 4 core 95 sqmm cable |
| 115 | Supplying & fixing medium gauge GI Pipe ( ISI-Medium-Zindal/Bansol/Tata) Protection with necessary fittings and jointing metarials as required40 mm dia |
| 116 | 50 mm dia |
| 117 | Supply & Fixing of 3 mm dia, heavy gauge (ISI) HDPE pipe (Make-TATA/Jindal/Skipeer) protection with necessary fitting and jointing meterials as required. |
| 118 | Boring (Micro Tunneiling) below the Pacca/Concrete Road with necessary tools & tackles for installation of 40/50mm dia GI pipe including fittings the vacant saace between pipe and road with soil. Mending good the damages as per direction of EIC. |
| 119 | Laying only Cable upto 50 sqmm through existing RCC/Hume/ GI Pipe/open masonary trench for single, 2, 3, 3½ & 4 core 6/10/16 sqmm cable. |
| 120 | Laying only Cable above 50 sqmm but not exceeding 400sqmm through existing RCC/ Hume/GI Pipe/open masonary trench forsingle, 2, 3, 3½ and 4 core |
| 121 | Laying of cable upto 3/4 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting |
| 122 | Laying of cable above 3½ core 50 sqmm and upto 3½ core 90 sqmm on wall/surface including S & F MS clams with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making hole etc. as necy., mending good damages and painting |
| 123 | Laying of cable as below, after cutting floor/pavement/wall/ and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbishFrom 2.5 sqmm to 35 sqmm at an average depth of 75 mm in floor/pavement/wall etc. |
| 124 | Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed |
| 125 | Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below :3 core 6 sqmm |
| 126 | 4 core 10/16 sqmm |
| 127 | 4 core 25 sqmm |
| 128 | 4 core 95 sqmm |
| 129 | Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials :3 core 6 sqmm cable |
| 130 | 4 core 10 sqmm cable |
| 131 | 4 core 16 sqmm cable |
| 132 | 4 core 25 sqmm cable |
| 133 | 4 core 95 sqmm cable |
| 134 | Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages,14 SWG |
| 135 | S & F of rectangular-shaped Metal sign Board (20 ft x 5 ft x 3 inch) frame above the entry Gate, fabricated and through welded by 4 sides 75 mm x 25 mm Mild Steel hollow bar (2mm thick) and 4 nos 25 mm x 25mm MS hollow bar (2 mm thick) in boardways. 1 no 25mm x 25 mm M.S hollow bar (2 mm thick) longs way. 35mm x 35mm x 5 mm thick angle iron around four corners for sufficient support and strength. The back side of the frame should be coverd by S & F of 20 SWG powder coated blue colour GI sheet with the following works. a. S & F of 3 mm thick exterior ACP sheet ( Make-Aistone/Aludecor/Times Bond) with approved colour as background on the front portion of the Sign Board (20 ft x 5 ft x 3 inch) including S & F aluminium angle , screw and all other necessary matenals as per direction of the EIC.b. S & F of angle iron (50 mm x 50 mm x 6 mm) having 180 cm length on RCC piller of the gate, providing holes. Two nos nut-bolts for fixing the board as requred.c. S & F of 4 nos 120 CM long arm bracket fabricated from 35 x 35 x 4 mm size MS angle iron rigidly fixed with the main structure of the board at the appropriate position for fixing lighting arrangment. Painting the above board structure GI sheet box, bracked incl. complete the board with one coat of RO primer and 2 coats of synthetic enamel paints (approved make) for inside and out side after preparation of the surface with sandpaper/emery paper. cleaning etc for receving primer and paint as per direction of E.I.C. After that the outside the board should be pained with blue paint as per direction of E.I.C. Inscription on the ACP board by supply & fixing raised (20 mm from back plate) stainless steel letters made from 22 SWG SS sheet with proper bending, moulding , grinding complete with nuts, bolt & solder properly. The size of letters will be subject to adjustment and as per the direction of E.I.C. The matter for the signage, Government of West Bengal , Assistant Director of Fisheries, Kalyani Fishfarm , B-15. Kalyani lake, kalyani.Nadia, PIN-741235 On the top letters there should be an instructed Emblem. The matter of the board should be approved by the concerned Authority.d. Supply and fixing of 240 V, minimum 50 watt , outdoor type LED Flood Light fitting/Luminaire with IP-66 protected. Wide beam. PDC housing glass complete accessories on the iron bracket/clamp on the board- 4 nos.( Make-Philips/K-light/Wipro/Havells).e. Makking necessary wiring by 3 core 1.5 sqmm PVC insulated stranded copper cable with PVC conduit and necessary connection to the four nos LED lights of this board from nearest loop box.f. Scaffolding charges for dismantling the existing board and fixing of new signboard at the Gate.g. Dismantling of existing damaged signboard and shifting it upto a lead of 50 Mtr. |
| 136 | Supply, Delivery & Installation of 1.50 Ton 3 star rating Non Inverter type A.C Machinewith all necessary arrangements. ( make-Hitachi/Daikin/O-General) |
| 137 | Installation, testing and commissioning of 1.5/ 2.0 Tr Split type A.C machine with IDU & ODU including supply & fixing of 40 mm x 40 mm x 5 mm M.S angle iron brackets (powder coated). Refrigerant RA10A/R-32 with necessary nut-bolt etc & mending the damages. |
| 138 | Supply , installation , testing & commissioing of suction /discharge copper pipe line in split air conditioning unit 1.5/2.0 Tr capacity including brazing, nitrile rubber insulation 6/9 mm thick class '0' etc complete required.Copper tube 3/8'' |
| 139 | Copper tube 5/8'' |
| 140 | Supply & drawing of 1.1 KV Grade 3 core 2.5 sqmm PVC insulated and stranded Copper Cable for connecting the power hub to ODU/ DU. |
| 141 | Providing & Fixing of ISI marked (IS-15778-2007) Rigid CPVC drain water pipe 6kg/cm2 with fittings like elbow, socket, Tee etc & support with M.S hanger on ceiling or recessed in wall with chasing & plastering with 6 mm thick closed cell elastomeric nitrile rubber insulation complete in all respect.25 mm dia |
| 142 | Sub Total |
| 143 | GST 18% |
| 144 | CESS 1% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 34 daysDec 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 37 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender