Tender For Certain Miscellaneous & Petty Repair Works In Otm & Md Accn Area Of Age B/R-Ii Under Ge(N) Ahilyanagar.
Tender Value
45 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
8 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ahmednagar → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Miscellaneous & Petty Repair Works In Otm & Md Accn Area Of Age B/R-Ii Under Ge(N) Ahilyanagar.
BOQ
| Sl. No. | Item Description |
| 1 | M&L for Disconnecting existing tanks, from water tank stagging of 2.5 to 4mtr Height setting aside (or lowering if required) for repairs, cleaning, etc, and Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etcand hoisting if required reconnecting and re-fixing in position.completely all as specified and as directed in following steps.1. Disconnecting existing watertank form all connection pipes Drain out the existing water inside water tank and and plug the holes of existing water tank temporarily.2. Lowering of existing water tank from water tank stagging.3. Removal of Sludge, by Scoop or vacuum out residual dirt or sediment, mud, and debris gathered at the bottom.4.Scrub Internal Surfaces: Use a mixture of detergent and hot water to scrub and cleanall internal surfaces of the tank. This can be done with a soft bristle brush or sponge or a high pressure jet. Avoid steel wool or hard metal scrapers that can scratch and damage the PVC surface.5 Disinfect: Fill the tank a quarter full with clean water. Sprinkle 160 grams of granular chlorine (HSCH) into the tank for every 1000 litres total capacity of the tank. Fill the tank completely with clean water, close the lid and leave to stand upto minimum 8 Hrs.6. Empty the Disinfect water, Fill the complete water tank and leave for 1 Hours.7. Once again Empty the tank and clean it with cotton cloth thoroughly8. Hoist the existing watertank to its orignal/new positon. 9. Connect the watertank to exisiting connections.and all existing fittings, unions, Couplings,Float valves air pipes etc.Note :- If tank is broken while removing,cleaning or refixing by Contractor. The penalty of 4 Rs per litre will be penalised by the GE and decision of GE will be Final. |
| 2 | M&L for Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc in existing positon by disconnecting completely all as specified and as directed in following steps. 1.Disconnecting existing watertank form all connection pipes Drain out the existing water inside water tank and and plug the holes of existing water tank temporarily.2.Removal of Sludge, by Scoop or vacuum out residual dirt or sediment, mud, and debris gathered at the bottom.3.Scrub Interior Surfaces: Use a mixture of detergent and hot water to scrub and cleanall internal surfaces of the tank. This can be done with a soft bristle brush or sponge or a high pressure jet. Avoid steel wool or hard metal scrapers that can scratch and damage the PVC surface.4 Disinfect: Fill the tank a quarter full with clean water. Sprinkle 160 grams of granular chlorine (HSCH) into the tank for every 1000 litres total capacity of the tank. Fill the tank completely with clean water, close the lid and leave to stand upto minimum 8 Hrs.5. Empty the Disinfect water, Fill the complete water tank and leave for 1 Hours.6. Once again Empty the tank and clean it with cotton cloth thoroughly7. Connect the watertank to exisiting connections.and all existing fittings, unions, Couplings,Float valves air pipes etc.Note :- If tank is broken while cleaning by Contractor. The penalty of 4 Rs per litre will be penalised by the GE and decision of GE will be Final. |
| 3 | Taking up or down 15 mm bore steel tubing and connections |
| 4 | .-Ditto- but 20 mm bore tubing |
| 5 | .-Ditto- but 25 mm bore tubing |
| 6 | M&L for Tubes 15mm bore of pipe medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floorss including all fittings complete all as specified. |
| 7 | M&L for Tubes, 20 mm bore of pipe medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floorss including all fittings complete all as specified. |
| 8 | M&L for Tubes, 25mm bore of pipe medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floorss including all fittings complete all as specified. |
| 9 | Fixing only Tubes,15mm bore of pipe medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floorss including all fittings complete all as specified. |
| 10 | Fixing only Tubes, 20mm bore of pipe medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floorss including all fittings complete all as specified. |
| 11 | Fixing only Tubes, 25mm bore of pipe medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floorss including all fittings complete all as specified. |
| 12 | M&L in repairs for 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed |
| 13 | M&L in repairs for 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed |
| 14 | M&L in repairs for 25mm bore Ball brass valves, high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed. |
| 15 | M&L in repairs for 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed. |
| 16 | S&F in repairs 50mm Unplasticized PVC pipes (SCH 40) as over flow pipes having pressure rating of 10 Kg/sqcm |
| 17 | Demolition of Stone slabs and tiles of any description or thickness in floors,walls etc laid, bedded and pointed in any mortar including bedding and backing coat etc. complete of any thickness complete all as specified and as directed by Engineer in Charge. |
| 18 | Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level. |
| 19 | Demolition of reinforced cement concrete of any descriptions and in any position etc complete all as specified and directed. |
| 20 | M&L for RCC Type B-1 1:2:4 using 20 mm graded aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and floor slab. |
| 21 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 22 | M&L for providing 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as directed. |
| 23 | M&L for Colured non - skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors. laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed in neat cement slurry and pointed in white or coloured cement to match,etc complete all as specified and as directed |
| 24 | .-ditto- all as per ser item No 23 but as in skirting on vertical surfaces over and including 10 mm thick backing coat in CM (1:3) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 25 | M&L for Virified Ceramic tiles Colured tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, as in floor etc laid over and including screed bed 15mm thick in cement and sand mortar (1:6) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed. |
| 26 | .-ditto- all as per ser item No 25 above but as in skirting on vertiical surfaces over and including 10 mm thick backing coat in CM (1:3) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 27 | M&L for Colured non - skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors. laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed in neat cement slurry and pointed in white or coloured cement to match,etc complete all as specified and as directed. |
| 28 | .-ditto- all as per ser item No 27 above but as in skirting on vertiical surfaces over and including 10 mm thick backing coat in CM (1:3) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 29 | M&L for non - skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors. laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed in neat cement slurry and pointed in white or coloured cement to match,etc complete all as specified and as directed. |
| 30 | M&L for coloured glazed ceramic tiles 300x450mm,7-8 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:3) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 31 | M&L for machine cut kota stone slab flooring 18-20mm thick over 20 mm thick screed base in cement and sand (1:6) mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge |
| 32 | M&L for Kota stone slab18-20mm thick in riser of steps, skirting, dado and pillar including 10 mm thick backing coat in cement and sand mortar (1:3) etc complete all as specified and directed by Engineer-in-Charge |
| 33 | M&L for 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick Screed bed etc complete all as specified and directed by Engineer-in-Charge. |
| 34 | M&L for Machine cut cudappah stone slab 20-22mm thick over and including 15mm thick cement and sand screed in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge |
| 35 | M&L for 25mm thick rough dressed lime stone slab (shahabad) flooring, laid dry, jointed and pointed in cement mortar 1:6 and pointed in cement mortar 1:3 ® in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed |
| 36 | Fixing only for 25mm thick rough dressed lime stone slab (shahabad) flooring, laid dry, jointed and pointed in cement mortar 1:6 and pointed in cement mortar 1:3 ® in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed |
| 37 | M&L for Rounding to edges full nosing of stone slabs one edge, such as in steps, cooking platform, and other similar situations completely all as specified and as directed by Engineer in Charge |
| 38 | M&L for Rounding to edges half nosing of stone slabs one edge, such as in steps, cooking platform, and other similar situations completely all as specified and as directed by Engineer in Charge |
| 39 | M&L for Rounding to edges Chamfer nosing of stone slabs one edge, such as in steps, cooking platform, and other similar situations completely all as specified and as directed by Engineer in Charge |
| 40 | M&L for 75mm thick plain cement concrete type C-1 (1:3:6) using 20 mm graded stone aggregate as in plinth protections & path, complete all as specified. |
| 41 | S&F in repairs for false ceiling with Vinyl faced Arm-Gyp-FB, ceiling 600 x 600 x 7-8mm thick with washable metalized polyester foil backing with Vinyl covered edges,including supporting sections as per Manufacturers instruction of same make shall be of suitable size from same makes embossed on sections and level adjuster duly suspended by 2 mm dia GI wire fixed to roof at 600mm centre to centre as per manufacturer's instructions / specification and all as directed including taking down/ out existing. Make- Armstrong/Saint Gobian (Gyproc) |
| 42 | S&F in repairs only false ceiling sheet with Vinyl faced Arm-Gyp-FB, ceiling 600 x 600 x 7-8mm thick with washable metalized polyester foil backing with Vinyl covered edges completely all as specified and all as directed including taking down/ out existing. Make- Armstrong/Saint Gobian (Gyproc) |
| 43 | Demolition of brickwork or stone bouilder masonary built in cement mortar or lime mortar complete all as specified |
| 44 | M&L for brickwork with fly ash bricks straight or curved on plan exc 6m mean radius, modular bricks built in CM 1: 6 complete all as specified |
| 45 | Raking out cement mortar joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses etc complete all as directed. |
| 46 | M&L for Flush Pointing to random rubble or polygonal rubble uncoursed or brought up to courses in CM 1:4 etc complete all as directed. |
| 47 | Taking down cement mortar plaster on Concrete surface, brick or stone walls, or ceiling surface including raking out joints, hacking for key complete all as directed |
| 48 | M&L for rendering, 10 mm thick on brick / concrete surfaces in cement mortar 1:6 surfaces finished even and fair etc complete all as specified. |
| 49 | M&L for rendering, 15 mm thick on stone/brick / concrete surfaces in cement mortar 1:4 finished even and fair complete all as specified and directed. |
| 50 | M&L for rendering 5mm thick on concrete surface of ceiling in CM 1:3 finished even and fair complete all as specified and directed. |
| 51 | M & L for preparation of newly plastered surface of wall and apply two coats of OBD over a coat of primer any height including scaffholding etc complete all as directed. |
| 52 | M & L for preparation of newly plastered surface of wall and apply three coats of white wash any height including scaffholding etc complete all as directed. |
| 53 | M & L for preparation of newly plastered surfaces of wall and applying two coats for cement based paint over a coat of alkali resistant priming paint any height including scaffholding etc complete all as directed. |
| 54 | M & L for preparation of newly plastered surface of ceiling and apply three coats of white wash any height including scaffholding etc complete all as directed. |
| 55 | M & L for preparation of old plastered surface of wall and applying one coats of cement base paint any height including scaffholding etc complete all as directed. |
| 56 | M&L for preparation of old plastered or unplastered surfaces of walls including cornices etc by brooming down or steel wire brushing scraping down smook soot, moulds, moss and efflorescent salt, trading oil and greasy spots and applying one coat of white lime wash at any height including scaffolding etc complete all as specified and directed by Engineer-in-charge. |
| 57 | .-ditto- all as per ser item No 56 (here-in-before) but on ceiling. |
| 58 | M & L for preparing old plastered surfaces of walls and apply one coat of OBD, finished with roller finish on plastered surfaces of wall any height including scaffolding etc complete all as specified and directed |
| 59 | M&L for preparation of old plastered treated surfaces of walls by brooming down and and applying one coat of weather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces complete all as specified and as directed. |
| 60 | M&L for complete removal of existing treatment by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7\\"/9\\" to make the surface free from dust, loose paint etc. by skilled labour including necessary scaffolding height upto 20m complete all as directed. |
| 61 | M&L for applying two coats of oil bound distemper using Airless spray technology over one coat of primer and minimum 1 mm thick white cement based wall care putty with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surfacecomplete all as specified and directed. Note : - Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. |
| 62 | M&L for two coat water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Fungal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint complete all as directed. Note:- For item No 60 to 62(a.) The work pertaining to periodical services shall be executed from authorized applicator through manufacturer of which the materials. i.e. Paint, Distemper, Cement base paint, Putty etc. is proposed to be used by the contractor and approved by Garrison Engineer.(b.) The contractor shall upload along with the documents under cover-I, ‘Memorandum of Understanding’ (MOU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected. |
| 63 | M & L for preparation of old wooden surface and applying one coat of synthetic enamel paint. |
| 64 | M & L for preparation of old steel surface and applying one coat of synthetic enamel paint. |
| 65 | S&F fix in repairs wash hand basin vitreous China white , flat back or angle type of size 500 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed by Engineer-in-Charge |
| 66 | S&F fix in repairs wash hand basin with pedestal vitreous China white , flat back or angle type of size 550 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed by Engineer-in-Charge |
| 67 | S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge. |
| 68 | S&F in repairs vitreous china wash down water closet (Pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device etc complete all as specified and directed by Engineer-in-Charge connecting to 'P' or 'S' trap etc complete all as specified and directed by Engineer-in-Charge. |
| 69 | S&F in repairs 10 ltr capacity PVC valve less, syphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 70 | S & F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified. |
| 71 | S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and directed by Engineer-in-Charge. |
| 72 | S & F in repairs looking mirror of size 600 mm x 450 mm etc complete all as specified and directed by Engineer-in-Charge. |
| 73 | Supply and fixing in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed. |
| 74 | Supplying and laying 16 mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified. |
| 75 | .-Ditto- all as per ser item no 74 above but 20 mm bore tubing |
| 76 | .-Ditto- all as per ser item no 74 above but 25 mm bore tubing |
| 77 | Cutting chases in brick/ block wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. |
| 78 | S&F in repairs stop cock/ anglecock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge |
| 79 | S&F in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge. |
| 80 | S&F in repairs twin (Two way) bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge. |
| 81 | S&F in repairs 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed. |
| 82 | S&F in repair PTMT bib tap 15 mm dia, screwed for iron pipe complete all as specified and directed. (Minimum weight 15mm-90Gms) Make - Prayag and equivalent. |
| 83 | S & F in repairs PVC flexible 32 mm Waste pipe for WHB, Sink etc complete all as specified. |
| 84 | M&L for Chromium plated Towel Ring fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) |
| 85 | M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement |
| 86 | S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps etc complete all as specifed and directed. |
| 87 | S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed in trenches or floor with necessary stay clamps etc complete all as specifed and directed. |
| 88 | S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed. |
| 89 | S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed in trenches or floor with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed. |
| 90 | S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed |
| 91 | S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed |
| 92 | S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore |
| 93 | S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore |
| 94 | S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore |
| 95 | S&F PVC (SWR) junction single, (double Y) equal or un equal 75mm bore |
| 96 | Celaning the surface with wire brush detecting sources of leakage and rekoving/taking down unsound treatment/ surface providing material and labour for carrying out non destructive water proofing treatment to sunken portion of slab, floor and walls of bath,WC,WHB and floor traps (Combined unit) by using contruction chemical method as hydrophobic PU grouting etc with first course of injection MDI based PU foam and second course of injection PU plain all as manufacturer's instruction etc, the PU foam shall have 100% solids and solvent free and shall expand 30-40 times its volume at liquid stage in presence of water, the PU plain injection shall have minimum 100 cps viscocity and shore hardness minimum 50 complete all as specified and as directed. Make:- Pidilite or equivalent. |
| 97 | Material and labour for fixing the metalic packer for hydrophobic PU foam including making holes and sealer all as per manufacturer's specification, the PU foam shall have 100% solids and solvent free and shall expand 30-40 times its volume at liquid stage in presence of water, the PU plain injection shall have minimum 100 CPS viscocity and shore hardness minimum 50 complete all as specified and as directed. Make:- Pidilite or equivalent.Note:- This item is catered only for material and labour by the metalic packer. |
| 98 | Material and labour for chemical cleaning of tile joints and re-grouting carefully by washing the existing tile with heavy duty cleaner preferably of M/s Pidilite or equivalent cleaner, again washing with fresh jet water, scratching the joints and filling the same with (white/matching colour) epoxy tile grout of M/s Pidilite, ROFF RTM epoxy or equivalent, curing,clening the surface etc as per saple done at site complete all as specified and as directed. |
| 99 | Material and labour for water proofing treatment to sunken floor slab, and peripheral walls, etc, and shall be carried out as specified below and as directed. (a) Clean the sunken portion of toilet / Baths/ WCs/ Kitchen thoroughly to remove laitance, dirt, dust etc.(b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar ( Dr fixit, Pidicrete URP, Thermax CC or eqvt).(c) Sanitary pipes entering through walls and floor shall be sealed with “Dr Fixit Bath seal Tape” and the gaps to be grouted with non-shrink cementitous grout “Dr Fixit Bath seal Grout” Thermax CC or eqvt. Nahani traps etc to be fitted securely and the gaps around it to be grounted in the same manner(d) Apply one coat of a Bitumen-modified polymer coating “Dr Fixit Bath seal Plus” or eqvt on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely(e) In the remaining area, in dry substrate condition brush apply “Dr Fixit Bath seal Plus” or eqvt first coat and further apply second coat when first is dry. Extend the coating upto 150mm above the FFL. Above FFL, another cementitious waterproofing waterproof coating “Dr Fixit Pidifin 2 K” Thermax CC or eqvt can be further applied right upto 2.1 m to waterproof the shower area also, if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely(f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed 1:3:6 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC spout pipe at the lowest point with 300 mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2 (including conreting).(g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of approved makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, Thermax CC etc. |
| 100 | Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge |
| 101 | Taking down chowkhats or frames exc. 1.5 sq. m and n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge |
| 102 | Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each etc complete all as specified and directed by Engineer-in-Charge |
| 103 | Taking down shutters of any description n exc 1 Sqm each etc complete all as specified and directed by Engineer-in-Charge |
| 104 | S&F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified, |
| 105 | S&F pressed steel door frame of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified, |
| 106 | S&F for factory made 35 mm thick IInd C/L H/W glazed & skeleton shutters open rebated and prepared to receive glass gauge, divided into square or rectangles with plain chamfered or rounded mitered & rebated slash bars including beads mitered for securing glass wire gauge etc all as specified |
| 107 | M&L for factory made 35 mm thick IInd C/L H/W plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated. |
| 108 | S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides |
| 109 | S&F 0.9 mm thick decorative laminate type 1 on Flush door surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions |
| 110 | S&F Solid PVC Door frame size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing. |
| 111 | S&F factory made solid PVC moulded Door shutter with particle board core, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back space, supplying and fixing in frame at site as per specification & drawing. |
| 112 | S&F 18mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work. |
| 113 | S&F frame 50 x 100 mm WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed bt Engineer-in-Charge. |
| 114 | S&F of Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as directed by Engineer-In-Charge. (Note: butt hinges and necessary S S screws shall be paid separately) |
| 115 | S&F of Factory made single extruded WPC (Wood Polymer Composite) solid plain cup board shutter of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per directed by Engineer-In-Charge. (Note: butt hinges and necessary S S screws shall be paid separately) |
| 116 | S&F 30mm width of flaps continuous (piano) hinges, mild steel, bright finish or electrogalvanised. |
| 117 | S&F powder coated aluminium anodised aluminium frame, shutters for door,windows, ventilators with one or more rebates including joining cleat for fixing etc, rubber / neoprene beading and locking arrangement etc complete all as specified and directed by Engr-in-Charge complete all as specified and directed by Engr-in-Charge. |
| 118 | S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 119 | S&F butt hinges medium weight cold rolled mils steel 100mm long. |
| 120 | S&F aluminium anodised barrel tower bolts of extruded section 150mm long. |
| 121 | S&F aluminium anodised handle of extruded section 150mm long. |
| 122 | S&F aluminium alloy, anodised, sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 300mm long. |
| 123 | S&F 300 mm mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed. |
| 124 | S & F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge. |
| 125 | S & F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge. |
| 126 | Hacking out old broken glass ( any thickness size ,quality or description ) from wooden/Steel frames glazed with putty or fixed with beads. |
| 127 | M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane. |
| 128 | M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads, rubber beding in squares exc 0.50 sqm in each pane |
| 129 | M & L for 4 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane. |
| 130 | M & L for 4 mm thick plain sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads, rubber bedding in squares n.exc 0.50 sqm in each pane. |
| 131 | M & L for 5.5 mm thick tinted sheet glass ordinary quality and glazing with oil putty or wooden beads in squares .exc 0.50 sqm in each pane. |
| 132 | M&L for 20 mm Mild steel Chromium plated curtain rods with end brakets and fixing stand/globe, of same material, haevy duty all as directed by Engineer in charge. |
| 133 | S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm etc complete all as specified and directed by Engineer-in-Charge. |
| 134 | S&F in repairs stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge. Make Nirali or equivalent |
| 135 | S&F in repairs plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. |
| 136 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 137 | S&F in repair fancy type brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge. |
| 138 | S&F in repair Aluminium body door closer for aluminium door shutter hydraulically regulated,designation No 1 universal type,suitable for door shutters up to 700mm in width and of weight not more than 35 kg and fixed. |
| 139 | M&L in repairs spouts of 75mm dia including jointing to waste pipe fixed in cement concrete type (1:2:4) type B1 using graded stone aggregate including removing old spouts etc complete all as specified and directed by Engineer-in-Charge. |
| 140 | M&L for PCC Type C-1 1:3:6 using 20 mm graded aggregates as in edges of floor tiles/blocks roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and directed by Engineer-in-Charge. |
| 141 | S & F in repairs steel Soap dish including necessary fitting material Scews etc complete all as specified. |
| 142 | S&F Vitreous China urinal, Half stall type, white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe andwaste pipe) |
| 143 | M&L Providing cement concrete Type C1 1:3:6 20mm graded aggregate) in kerbs or mud stops, rounded or chamfered on edges including demolition all as specified & directed by Engineer-in-Charge. |
| 144 | M&L for 150mm bore Reinforced cement concrete pipe, type NP-2 laid in trenches and jointed as specified, making necessary connections after cutting into existing sewer line /manhole to make it functional after taking down/out salt glazed ware, AC or reinforced concrete pipe as existing at site complete all as specified and directed. |
| 145 | Cutting into existing manhole for connecting new drain 150 mm internal dia of pipe making good to pipe and rendering cutting out existing benching for good forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B1 using graded stone aggregates, smooth finished and as required for 100mm internal dia pipe etc complete all as specified and directed by Engineer-in-Charge. |
| 146 | M&L for cement concrete bed to 100mm bore pipe including packing under and hauching against the sides of pipe in PCC (1:4:8) type D-2 using 40 mm graded mechanically crushed stone aggregates, after they are laid and tested in etc complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender