Tender For Special Repair To Bldg No P-130 Outer Dinning Hall (Size 85 X 32 Ft) At Auto Regt & 04 X Toilets And Bathrooms Of Bldg. No P-91 (Otm) And 08 X Toilets Of Bldg. No P-85 (Office Complex) At Ac Records Under Ge(N) Ahilyanagar
Tender Value
47.90 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
15 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ahmednagar → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No P-130 Outer Dinning Hall (Size 85 X 32 Ft) At Auto Regt & 04 X Toilets And Bathrooms Of Bldg. No P-91 (Otm) And 08 X Toilets Of Bldg. No P-85 (Office Complex) At Ac Records Under Ge(N) Ahilyanagar
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc.15cm thick below or above ground level. |
| 2 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc. |
| 3 | Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor and removing all rubbish/dismantled material outside MD Land. all as directed. |
| 4 | M&L for providing 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as directed. |
| 5 | M&L for Reinforced cement concrete (design mix) of M20 type in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as directed by Engineer-in-Charge. |
| 6 | M&L for Mild steel deformed bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 7 | S&F coloured glazed ceramic tiles 300x450mm, 7-8 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 8 | S&F non skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile 400x400mm , as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed. |
| 9 | S&F joint free non skid ceramic coloured tiles 300x300mm 7-8mm thick matching to dado tiles area of each tile, as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed. |
| 10 | M&L for 15 -18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick Screed bed etc complete all as specified and directed by Engineer-in-Charge. |
| 11 | M&L for Machine cut cudappah stone slab 20-25mm thick over and including 15mm thick cement and sand screed in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge. |
| 12 | M&L in repairs for machine cut kota stone slab flooring 18 -20 mm thick over 20 mm thick screed base in cement and sand (1:6) mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge. |
| 13 | M&L for Kota stone slab 18 - 20 mm thick in riser of steps, skirting, dado and pillar including 15 mm thick backing coat in cement and sand mortar (1:4) etc complete all as specified and directed by Engineer-in-Charge. |
| 14 | Demolition of brickwork or stone bouilder masonary built in cement mortar or lime mortar complete all as specified |
| 15 | M&L for old size brickwork with fly ash bricks straight or curved on plan exc 6m mean radius,built in CM 1: 6 complete all as specified |
| 16 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in 1: 6 complete all as specified. |
| 17 | Taking down cement mortar plaster on brick or stone walls, raking out joints, hacking for key complete all as directed. |
| 18 | M&L for 15 mm thick rendering on wall surface in CM 1:4 in with water proofing compound incl. finishing the surface even and smooth without using extra cement. (WPC shall be measured and paid seperately) |
| 19 | M&L for Rendering 10 mm thick on fair faces of brick work or on concrete surfaces in CM 1:6 finished even and fair without using extra cement including sagol finished complete all as specified. |
| 20 | M&L for rendering 5mm thick on concrete surface of ceiling in CM 1:3 finished even and fair without using extra cement complete all as specified and directed. |
| 21 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L for preparing new plastered surfaces of walls and apply two coat of OBD, finished with roller finish on plastered surfaces of wall any height including scaffolding etc complete all as specified and directed |
| 23 | .-ditto- all as per ser item No 22 above (here-in-before) but on ceiling. |
| 24 | M & L for preparing old plastered surfaces of walls and apply two coat of OBD, finished with roller finish on plastered surfaces of wall any height including scaffolding etc complete all as specified and directed |
| 25 | .-ditto- all as per ser item No 24 above (here-in-before) but on ceiling. |
| 26 | M&L for preparing new unplastered or plastered surfaces and applying two coats of oil bound distemper including chalk whitening on wall including smooth roller finish complete all as directed. |
| 27 | M&L for 1 mm wall care putty on walls complete all as specified and directed by Engg-in-charge. |
| 28 | S&F fix in repairs wash hand basin vitreous China white, flat back or angle type of size 500 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed by Engineer-in-Charge. |
| 29 | S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge. |
| 30 | S&F in repair Vitreous china premium/ 1st quality wash down water closet wall hung\ EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge. |
| 31 | S&F in repair vitreous China urinal, Half stall type, white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe andwaste pipe) |
| 32 | S&F in repair Vitreous China Urinal, full stall type, white with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) |
| 33 | Supply only 10 ltr capacity PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and directed by Engineer-in-Charge. |
| 35 | Taking up or down 15 mm bore steel tubing and connections |
| 36 | .-Ditto- all as per ser item No 35 above but 20 mm bore tubing |
| 37 | .-Ditto- all as per ser item No 35 above but 25 mm bore tubing |
| 38 | Supplying and laying 16 mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified. |
| 39 | .-Ditto- all as per ser item No 38 above but 20 mm bore tubing |
| 40 | .-Ditto- all as per ser item No 38 above but 25 mm bore tubing |
| 41 | S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified. |
| 42 | S&F in repairs stop cock/ anglecock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge. |
| 43 | S&F in repairs decorative towel ring recangular chromium plated fixed with (CP) brass screws of approved qualityas specified |
| 44 | Supply and fix in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed. |
| 45 | Supply and fix in repair health faucet with 15 mm dia 1.25 m long flexible tube wall mounted / hooked including making connection and fixed in position complete all as specified and directed by Engg-in-charge |
| 46 | S&F in repairs fancy type twin (Two way) bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge. |
| 48 | Supply only 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed. |
| 49 | Supply only PVC flexible 32 mm Waste pipe for WHB, Sink etc complete all as specified. |
| 50 | M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement |
| 51 | S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed. |
| 52 | .-Ditto- all as per ser item No 51 above but as in trenches or floor |
| 53 | S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed. |
| 54 | .-Ditto- all as per ser item No 53 above but as in trenches or floor |
| 55 | S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed |
| 56 | S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed |
| 57 | S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore |
| 58 | S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore |
| 59 | S&F bands, straps, supports or stays for rain waterpipes, hooks (stay) heavy for large gates, hook and pintle hinges clamps, hold fasts wall ties, hooks for hanging fans and similar small articles Fe-290 Gde- E-165 or Fe-310-0 complete all as specifed and directed. |
| 60 | M&L for special treatment to sunken slab floor (Area of Sunken Portion n exc 1.50 Sqm) incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforced with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, etc after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge. Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE. |
| 61 | M&L for special treatment to sunken slab floor (bottam and vertical portion) etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforced with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE. |
| 62 | S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 2000 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected including dismantling water tanks and removing to store etc complete all as directed. |
| 63 | Cutting chases in brick/ block wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth |
| 64 | Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge. |
| 65 | Taking down chowkhats or frames exc. 1.5 sq. m and n.exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge. |
| 66 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per directed by Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 67 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per directed by Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 68 | S&F Solid PVC Door frame size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing. |
| 69 | S&F factory made solid PVC moulded Door shutter with particle board core, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back space, supplying and fixing in frame at site as per specification & drawing. |
| 70 | S&F Powder coated aluminium anodised aluminium frame, shutters for door,windows, ventilators with one or more rebates including joining cleat for fixing etc, rubber / neoprene beading and locking arrangement etc complete all as specified and directed by Engr-in-Charge |
| 71 | S&F butt hinges medium weight cold rolled mils steel 100mm long. |
| 72 | S&F aluminium anodised barrel tower bolts of extruded section 150mm long. |
| 73 | S&F aluminium anodised handle of extruded section 150mm long. |
| 74 | S&F aluminium alloy, anodised, sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 300mm long. |
| 75 | S&F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge. |
| 76 | Hacking out old broken glass (any thickness size, quality or description) from wooden/ Steel frames glazed with putty or fixed with beads. |
| 77 | M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane. |
| 78 | S & F in repairs looking mirror of size 600 mm x 450 mm etc complete all as specified and directed by Engineer-in-Charge. |
| 79 | Full moulding of stone slabs one edge, two edge, as in steps cooking platforms jambs and cills and other similar situations complete all as specified & directed. |
| 80 | S&F Soap dish, vitreous China white, approximate size 160x 160x90mm |
| 81 | M&L for PCC (1:2:4) Bo using 12.5 mm graded stone aggregate as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc,with approved water proofing compound all as per manufacturer's instructuions on the roof surface to achieve requisite slope all as specified and directed. (Note :- Supply only water proofing compound shall be measured & paid separately). |
| 82 | M&L for providing water proofing treatment on roofs, as per manufecturer's instructions and as specified after taking down/out as existing at site :- (a) Cleaning the newly plastered surfaces with wire brushes and applying a coat of bituminous primer @ 0.30 ltrs/sqmts and allow to dry.(b) Applying and laying torch APP polymer modified bituminous membrance 3 mm thick with non woven polyster matt as reinforced weighing not less than 3 kg/sqmts by thermofusion process as per manufacturers specification including applying one coat of aluminium paint. Make : Super Thermolay of STP / Equivalent in Dr Fixit, Fosroc.Note : (i) Work has to be carried out strictly by the authonticated applicator of the manufacturer and as per manufacturers specification as approved by GE.(ii) Certificate from manufacturer shall be submitted by the contractor. (iii) Including taking down of old APP Membrane. |
| 83 | Supply only Integral water proofing compound |
| 84 | Taking down carefully copper/ aluminum point wiring (light/ fan/ bell/ socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Charge. |
| 85 | M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS cable drawn in and incl PVC Casing and capping ISI Marked with its accessories PVC boxes (upto 12 module suitble for Mylinc series of Legrand including white plates with frame upto 12 module of make suitable for Mylinc Series ) for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note :1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black)2. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc |
| 86 | One light point controlled by switch 5 Amp single pole one way |
| 87 | One fan/exhaust fan point controlled by switch 5 Amp single pole one way |
| 88 | One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch |
| 89 | .-ditto- all as per ser Item No 85 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board |
| 90 | S&F in replacement Modular Switch, 6 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge |
| 91 | S&F in replacement Modular Switch, 16 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge |
| 92 | S&F in replacement Modular Socket Outlet 6 Amp, 3 pin, combined two module etc as per existing complete all as specified and directed by Engineer-in-Charge. |
| 93 | S&F in replacement Modular Socket Outlet 6 Amp / 16 Amp - 2/3 pin combined two module as per existing etc complete all as specified and directed by Engineer-in-Charge |
| 94 | Supply & fix lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge |
| 95 | S&F ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge |
| 96 | S&F in replacement double door Sheet metal enclosures factory made DBs SPN, 4 way, 240 volts, protection class IP-42, suitable for fixing of MCBs,, confirming As per IEC 61439-3, Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar, With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed. |
| 97 | Supply & fix MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 10KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge |
| 98 | Supply & fix MCBs, SPN, AC, 240 volts of 40 Amps capacity 10 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge. |
| 99 | S&F in replacement square profile LED lighting fixture, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 20 Watt with LED light source 6500 K,input voltage 160V-270V with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge . |
| 100 | S&F in replacement square profile LED lighting fixture, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 10 Watt with LED light source 6500 K,input voltage 160V-270V with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge . |
| 101 | S&F LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED light fitiing 10 Watt with LED lamp source 6500 K with uniform light output, with all accessories including its connection with 2 core seathed copper conductor cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge |
| 102 | S&F sub main wiring with two single core PVC insulated, unsheathed, FRLSH stranded copper conductor cable 4 Sqmm with 4 Sqmm PVC insulated, unsheathed, FRLSH stranded copper conductor cable as earth wire drawn through and including PVC Casing and capping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge Note :1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black)2. Two run of 4 Sqmm cable i.e for one run for phase, one run for neutral with one run of 4 Sqmm cable for earth and one run of PVC Casing & caping shall be measured as one unit. |
| 103 | Supply and fix electric water heater, storage type steel body and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, including Flexible pipe 2 set , PVC Connection pipe fastner fixed in wall Complete etc. |
| 104 | Taking out/down carefully and opening of existing water Geysers of 25 Ltrs capacity,from any position, of any make etc & refixing after reassembling and after repair /replacement of spare parts/ material/items, at the desired location and making necessary water inlet, outlet & electric connections to make in functional by using material/parts of minor nature such as screws, insulation tape, nuts, bolts, washers etc including cleaning and painting with spray painting to required gloss with white synthetic enamel paint and removinng to sotorecomplete body & writing MES No with black paint etc complete all as specified and directed by Engineer-in-Charge |
| 105 | S & F for plastic body exhaust fan, AC single phase, 240 V of size 200 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender