Tender For special Repair Of Single Jcos Living Bldg No P-39, Provn Of Rainwater Harvesting Alongwith Drainage System Around Jco Mess Bldg No T-149 Of Inf Div Pro Unit, Addn/ Altn To Toilet And Roof Treatment Of Bldg No P-44 (Drying & Ironing) And Dr
Tender Value
44.72 Lakhs
Estimated cost
Bid Submission
02 Nov 2026
10 days left
EMD
89440
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Firozepur → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Single Jcos Living Bldg No P-39, Provn Of Rainwater Harvesting Alongwith Drainage System Around Jco Mess Bldg No T-149 Of Inf Div Pro Unit, Addn/ Altn To Toilet And Roof Treatment Of Bldg No P-44 (Drying & Ironing) And Drainage Near Bldg No P-02 To P13 Of Dogra Under Ge (East) Ferozepur Cantt
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of brick tiles single layer laid on roof jointed & pointed in cement mortar, complete all as specified and directed by Engineer-in-charge. |
| 2 | Demolition mud in roofs, any thickness, including plastering and leaping etc including removing rubbish upto 500 mtr from the site complete all as specified and as directed by Engineer-in-charge |
| 3 | M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in roof padding complete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L for Rendering 10 mm thick cement mortar 1:4 mixed with integral water proofing compound as per manufacturer instruction over the padding concrete while still the concrete is still green, complete all as specified and as directed by Engineer-in-charge |
| 5 | M&L for water proofing treatment to roof surface including parapet wall comprising with the following course of treatment/Specifications from bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25@ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including prepration of roof surfaces complete all as specifiedand as directed by Engineer-in-Charge.(b) One layer of APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) land on primed surface by torched application. Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside groove of parapet walls and shall be finised by a membrane flashing.Note:- (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be 75 mm length wise and 100 mm width wise of polymeric membranes repectively ansd sealed all overlaps and joints as manufacturer's instructions.(iii) The whole works shall be executed by the authorised company applicator. |
| 6 | M&L for two coat of aluminium paint over APP membrane complete all as specified and as directed by Engineer-in-charge |
| 7 | Demolition of brick work or stone/ boulder masonary built in cement mortor including all quoins, arches, pillars etc, complete all as specified and directed. |
| 8 | M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in c:m 1:6 all, complete all as specified and directed. |
| 9 | All as per srl item No 08 here-in-before but using old bricks retrieved from dismantling under ser item 7 here-in-before including cleaning and removal of mortar from old bricks etc, complete all as specified and directed |
| 10 | Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed |
| 11 | M&L for Rendering 12 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed |
| 12 | M&L for Rendering 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed |
| 13 | M&L for Rendering 5 mm thick cement plaster on ceiling surfaces in cement mortar 1:3 finished fair and even without using extra cement, complete all as specified and directed |
| 14 | Complete removal of existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in CM 1:3 & applying 02 mm thick waterproof wall putty on the bldg internall surface of wall with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm & making surface absolutely smooth on entire satisfaction of Engineer-in-Charge |
| 15 | M&L for applying two coat of distempering new plaster / Putty surface with 1st quality acrylic distemper oil emulsion of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology to prepare the surface even and smooth on new surface, complete all as specified and directed |
| 16 | M&L for preparing newly plastered surfaces of wall and applying 2 coats of distemper oil emulsion over 02 mm thick waterproof wall putty on the bldg internall Plaster surface of wall with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm of any shade on walls surfaces, complete all as specified and directed |
| 17 | Complete removal of existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in CM 1:3 & applying 02 mm thick water proof wall putty on the bldg external surface of wall with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm & making surface absolutely smooth on entire satisfaction of Engineer-in-Charge, complete all as specified and directed. |
| 18 | M & L for 02 mm thick water proof wall putty on the bldg external surface of wall with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm & making surface absolutely smooth on entire satisfaction of Engineer-in-Charge, complete all as specified and directed. |
| 19 | M&L for applying new surface i.e complete remove surface putty treated surface/new plaster surface two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm the surface even and smooth complete all as specified and directed. |
| 20 | M&L for Complete removal of existing treatment including preparation of surfaces of walls & applying two coats of cement base paint, complete all as specified and directed. |
| 21 | M&L for Preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer on surfaces of walls with paint roller complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L for Preparation of new plastered surfaces of ceiling & applying three coats of white wash, complete all as specified and directed. |
| 23 | M&L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and directed. |
| 24 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts and removing from site to store or otherwise, complete all as specified and directed |
| 25 | All as per srl item No 24 here-in-before but size exceeding 1.5 Sqm and not exceeding 4 Sqm each, complete all as specified and directed |
| 26 | S&F for Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mm including one shop coat of red oxide primer, complete all as specified and directed. |
| 27 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 28 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified & directed. |
| 29 | S&F Providing 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings. |
| 30 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 31 | S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube, complete all as specified and directed |
| 32 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail MS frame shall be covered with heat moulded plain / coloured PVC \\"C\\"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles & rails with suitable PVC sheet beading and jointed togeather with solvent cement, complete all as specified and directed. |
| 33 | Dismantling of boarding, any description, fixed in any position with nails, complete all as specified and directed. |
| 34 | S & F factory made PVC cup boards/ Shelf / Partition of required size consisting of panel of 18mm thick Celuka PVC Ply and for supporting the hold of Shelf/ Partition and shall provided 3 edges in size 18mm x18mm as per required length. The front side of the edge visible in the front of the shelf/ Partition to be edge lipped by 18mm width x 1mm thick PVC sheet using solvent cement etc. complete all as specified.Note Colour of PVC shelf approved by Engr -in charge. |
| 35 | S&F Continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 30mm,fixed with steel screw, complete all as specified and directed |
| 36 | S&F in repair 100mm long hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws and fixed, complete all as specified and directed |
| 37 | M&L for Preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed |
| 38 | S&F PTMT butt hinges, 100 mm long and fixed with steel screws, complete all as specified and directed |
| 39 | S&F PTMT tower bolts, 150 mm long and fixed with steel screws, complete all as specified and directed |
| 40 | S&F PTMT door handle, 150 mm long and fixed with steel screws, complete all as specified and directed. |
| 41 | S&F Butt hinges size 100 mm medium weight, cold rolled mild steel, and fixed as specified and directed. |
| 42 | S&F Aluminium bow handle 150 mm long and fixed with steel screws, complete all as specified and directed. |
| 43 | S&F Aluminium tower bolts 150 mm long and fixed with steel screws, complete all as specified and directed. |
| 44 | S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed |
| 45 | S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed. |
| 46 | S&F 300 mm mild steel ordinary rat tail spring including roller and roller plate, complete all as specified and directed |
| 47 | S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed |
| 48 | S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed |
| 49 | Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed.Note:- (i) Aluminium chowkhat /frame, glass,wiremess and aluminium grill shall be measured and paid separately. |
| 50 | S&F 4.8 mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and as directed. |
| 51 | S&F 4.0 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane fixed to aluminium ventilator, complete all as specified and directed. |
| 52 | Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with pproved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. |
| 53 | S&F Mild steel curtain rod powder coated with fixing side brackets,end cups,rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws, complete all as specified and directed. |
| 54 | Demolition of un reinforced cement concrete of any description and in any position not otherwise specially provided for, complete all as specified and directed. |
| 55 | M&L for Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints, complete all as specified and directed. |
| 56 | M&L 25 mm thick cement concrete (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in sub base of flooring,surface finished rough to receive floor topping, complete all as specified and directed. |
| 57 | M&L for 10 mm thick rendering over concrete surface of sunken floor in CM 1:3 and applying bitumen blown any grade applied two coats to concrete surface / rendering at the rate of 1.5 kg per sqm per coat and treating the sunken floor all as specified and directed. |
| 58 | M&L for water proofing treatment to RCC sunken floor including wall comprising with the following course of treatment/ specifications form bottom to top:-(a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.40 ltr per sqm including preparation of roof surfaces complete all as specified and as directed.(b) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application ccomplete all as specified and directed.Note: (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions.(ii) A minimum overlap shall be not to be less than 150mm of polymeric membranes and sealed all overlaps and joints as manufacturer's instructions. (iii) All CI/PVC traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15 cm) all round. |
| 59 | M&L for Cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregate as in filling in sunkan slab or in mass concrete, complete all as specified and directed |
| 60 | S&F PVC (SWR) pipes 40 mm bore including fixing to walls as in spouts of sunken portion, complete all as specified and directed |
| 61 | M&L for Shotcreting average thickness 50 mm in RCC columns, beams and slab etc. (with mix minimum cement content of 350 Kg per Cum, M-25). Concrete having the specified minimun characterstic compressive strength (with ordinary portland cement, corarse sand and graded stone aggregates of 6 mm maximum size in proportion as per design criteria) incl the cost of centering and shuttering at edges and corner etc as directed by Engr-in-Charge incl chipping of unsound/week concrete mateial 50 mm average thickness from slabs, beams/columns etc with mannual chiesels or stenderd power driven percussion type or of approved make incl tapering of all edges, make square shoulder of cavities incl cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removel of rust by applying approved rust remover chemical and the coating with Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron as per specification, applying the Latex based bonding agent on each layer of the shootcreting work of Pidicrete URP on the entire surface complete all as directed including 5 mm thick cement plaster in CM (1:3) finished even and smooth without using extra cement including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete as specified and as directed.Make:- Sika/Fosroc/Pidilite or Techno as approved by GE in writing from E-in-C's approved list. Note : (i) Complete treatment to be executed by approved applicator.(ii) hard drawn steel wire fabric to be paid seperately. |
| 62 | Supply and fixing hard drawn steel wire fabric not exc 4 kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed. |
| 63 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons laid bedded , dry and pointed etc, complete all as specified and directed. |
| 64 | M&L for 18 to 20 mm thick Baroda green marble in single piece incl nosing at front and sides in steps, jambs, pillars, window cills, cooking platforms, staircase and like with bull nosing in cm(1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including making grooves for slip guard or steps, edge moulding, making 30 mm dia hole in cooking counter slab and green marble top for gas pipe including 15mm thick screed bed in cm 1:4 and providing edge moulding to marble incl machine polishing to edge to finish etc complete all as specified and directed by Engr-in-Charge. |
| 65 | M&L machine cut kota stone flooring 18-20 mm thick over & including 20mm thick screed bed in cement mortar 1:6, laid jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing and including roughing surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, complete all as specified and directed. |
| 66 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified and directed. |
| 67 | Cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base of floor topping, 75 mm thick, complete all as specified and directed. |
| 68 | M & L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade, jointed and pointed with gray cement and pigment over sand cushioning complete all as specified and directed.Note :- The colour of tiles Red/Yellow approve by Engr -in -charge. |
| 69 | M & L sand filling under floors or in foundations including watering and consolidation complete all as directed by Engieer-in-charge . |
| 70 | Dismantling floor, hearth or wall tiling including cement mortar beding (but not backing),removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 71 | M & L Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),primium quality area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed. |
| 72 | M & L for Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),primium quality area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed. |
| 73 | Glazeded ceramic coloured (colour & shade as approved) tile 450x300x6to7mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white/ coloured cement with pigment to match the colour of tiles, complete all as specified and directed. |
| 74 | S&F for Joint less non skid ceramic tiles 7-8 mm thick (square/rectangular) polished dark shade, area of each tile exceeding0.18 but n exc 0.38 sqm in flooring etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed. |
| 75 | Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed. |
| 76 | All as per item No 75 here-in-before but 20 mm bore tubing, complete all as specified and directed. |
| 77 | M&L for GI steel water tubing, 15mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor, complete all as specified and directed. |
| 78 | All as per item No 77 here-in-before but 20 mm bore tubing, complete all as specified and directed. |
| 79 | Fixing only, after cleaning old steel water tubing,15 mm bore and connections in new or old position using new fittings, complete all as specified and directed. (pipes obtained from item 75 to be reused). |
| 80 | All as per item No 79 here-in-before but 20 mm bore (pipes obtained from item 76 to be reused), complete all as specified and directed. |
| 81 | S&F in repair bib taps, fancy type CP, screwed for 15mm bore of iron pipe or for brass ferrule and fixed, complete all as specified and directed. |
| 82 | S&F in repair stop valves, fancy type, CP with long shank and cup ( concealed type ), screwed both ends for 15mm bore of iron pipe or for union and fixed, complete all as specified and directed. |
| 83 | S&F in repair stop valves/angle cock,fancy type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 84 | S&F in repair gunmetal gate valve of 20mm dia with iron wheel head screwed both ends for iron pipe, complete all as specified and directed. |
| 85 | S & F PVC connection 15 mm size PTMT nuts of length 450 mm fixed, complete all as specified and directed. |
| 86 | S&F in repair Water storage tanks 1000 liters capacity rotational moulded, triple layer polythene (cyindrical vertical with closed top) hoisting and fixed in position on roofs including dismantling existing water storage tank, complete all as specified and directed. |
| 87 | S & F Ball valve of PVC, 20mm bore, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed. |
| 88 | S & F in repair Vitreous China wash down water closet pan (pedestral pattern), White (excluding fixing bolts, flushing cistern and flush pipe), with plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and as directed. |
| 89 | S&F PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. complete all as specified and directed. |
| 90 | S & F in repair Health faucet ( ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexible tube and Abs wall hook including making connections and fixed in position complete in all as specified and directed. |
| 91 | S&F Vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste coupling fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing, complete all as specified and directed. |
| 92 | S&F in repair 125 mm chromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union, complete all as specified and directed. |
| 93 | S & F Looking mirror of selected quality beveled edge glass of size 600x450 mm and backing with 6mm thick AC building board and fixed to wall with PVC rawl plugs with chromium plated brass screws and cup washers as in repairs, complete all as specified and directed. |
| 94 | S&F Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs as in repairs, complete all as specified and directed. |
| 95 | S & F corner glass shelves 300 mm radius 8 mm thick as per sample radius for bathroom, fixed on suitable support of brass chromium plated clips complete all as specified and directed. (Make: Prayag, Somany, Cera). |
| 96 | S&F Stainless steel soap dish (not less than 1mm thick) of type as directed,fixed to walls with chromium plated brass screws with wooden/rawl plugs, in repair, complete all as specified and directed. |
| 97 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 98 | S&F Mild steel framed work of Fe-410-0 or Fe-310-0 (Fe-290 Gde-E-165) as in railing or gate of angle or other section with gusset plates,rails, braces etc and fixing, complete all as specified and directed. |
| 99 | Dismantling CI pipe/PVC pipe alongwith fittings of 110mm dia, below or above ground level, jointed in cement mortar and taking out, complete all as specified and directed. |
| 100 | S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches, complete all as specified and directed. |
| 101 | S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches, complete all as specified and directed. |
| 102 | S&F 110 mm dia PVC ( rain water ) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed. |
| 103 | S&F 75mm dia PVC (SWR) bends any radius complete all as specified & directed. |
| 104 | PVC (SWR) bend (any radius), 110mm bore, diminishing pieces or tapers (larger bore measured) jointed in cement mortar, complete all as specified and directed. |
| 105 | S&F 75mm dia Junction single (Single or double T) equal or unequal complete all as specified & directed. |
| 106 | S & F PVC (SWR) junction single, (single T) equal or unequal 110 mm, complete all as specified and directed. |
| 107 | M&L PVC (SWR) floor trap 75 mm, plain with PVC grating including jointing with solvent cement etc., complete all as specified and directed. |
| 108 | M&L for 25mm thick precast cement concrete jafferi jallies,(1:2:4) 12.5mm graded stone aggregate type BO (measured solid), including all mouldings but excluding frame all as specified and as directed. |
| 109 | Dismantling Asbestos cement/GI (corrugated, semi corrugated, etc) ) sheets in on roof coverings, complete all as specified and directed. |
| 110 | S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed. |
| 111 | S&F rolled mild steel channel, angle as in purline, rafter & vertical type etc on roof cutting to dead length where required and welding to each other complete all as specified and as directed. |
| 112 | M&L for rendering 10 mm thick in CM 1:6 over brick / concrete surfaces finished even and smooth without using extra cement etc including taking down cement plaster on brick or concrete surfaces on wall/ ceilling/ stone/ block etc including racking out joint, hacking for key, scrubbing down with water etc and and preparing new plastered surfaces and applying two coats of oil bound distemper paint on surfaces of walls with paint roller over 3mm wall care putty complete all as specified and directed by Engineer-in-Charge |
| 113 | M&L for complete removal of existing treatment on surfaces of walls apply two coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology and providing 2mm thick wall care putty and sanding the surface to prepare the surface even and smooth, complete all as specified and directed. |
| 114 | M & L for applying two coats of white wash on old Ceiling surface including preparation of surface, complete all as specified and directed. |
| 115 | M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick cement base putty and sanding the surface to prepare the surface even and smooth complete all as specified and directed at any height incuding necessary scaffolding over new/complete removal surfaces. Contd...115.01/- Please Enable Macros to View BoQ information |
| 116 | M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick cement base putty and sanding the surface to prepare the surface even and smooth complete all as specified and directed at any height incuding necessary scaffolding over new/complete removal surfaces. Contd...115.01/- Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender