Tender For Provision Of Dg Set For Security Lights And Pumping Installation And Allied Works At Lekawada Gandhinagar Under Ge (I) (Cg) Gandhinagar
Tender Value
43.07 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
3 days left
EMD
86500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gandhinagar → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Dg Set For Security Lights And Pumping Installation And Allied Works At Lekawada Gandhinagar Under Ge (I) (Cg) Gandhinagar
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting in any type of soil, complete all as specified and directed. |
| 2 | Excavation in trenches not exceeding 1.5 Metre wide and not exceeding 1.5 Metre depth for foundation and getting out in soft and loose soil, complete all as specified and directed. |
| 3 | Excavating in post holes (or similar holes) each not exceeding 0.50 Cum and getting out in loose /soft soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layer not exceeding 25cm, watering, and removing surplus soil to a distance not exceeding 50 Metre and making good surface, complete all as specified and directed. |
| 4 | Material & Labour for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed. |
| 5 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm (soil) complete all as specified and directed. |
| 6 | Removing excavation materials not exceeding 50 Metre and deposition where directed at a level not exceeding 1.5 Metre above the starting point (soil) complete all as specified and directed. |
| 7 | Material & Labour for cement concrete 1:4 :8 type D-2, using (40mm graded aggregate) as in filling, foundation, mass concrete and sub base of floors etc complete all as specified and directed. |
| 8 | Material & Labour for Spreading, levelling, watering and well ramming the earth filling under floor not exceeding 25cm thick in layers, complete all as specified and directed.Note :- Soil obtained from excavation shall be used for filling under floors. |
| 9 | Material & Labour for providing cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in lintels upto 1.5 Metre clear span, copings, bed plates (block), cills, steps and other bands, parapet and railing upto 60cm height, complete all as specified and directed. |
| 10 | Material & Labour for hard-core of broken bricks gauge not exceeding 63mm, deposited spreader and levelled in layer not exceeding 15 cm thick, watered and rammed to a true surface, broken stone or boulder complete all as specified and directed. |
| 11 | Material & Labour for 75mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base of floors complete all as specified and directed. |
| 12 | Material & Labour for 75mm thick cement concrete 1:3:6 type C-2, in plinth protection finished even and smooth without using extra cement, complete all as specified and directed. |
| 13 | Material & Labour for brick work with fly-ash bricks straight or curved on plan exceeding 6 Metre mean radius built in Cement Mortar 1:6, complete all as specified and directed. |
| 14 | Material & Labour for brick work with fly-ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. |
| 15 | Material & Labour for 10mm thick rendering in Cement Mortar 1:3 to ceiling surfaces finished even and smooth without using extra cement including preparation of new surface & Three coat of white wash complete all as specified and directed. |
| 16 | Material & Labour for rendering 15mm thick on fair faces or other than fair faces of brick work in Cement Mortar 1:6 finished even & smooth without using extra cement, complete all as specified and directed. |
| 17 | Material & Labour for Preparation of newly plastered wall surfaces and applying two coats oil bound distemper over a coat of primer complete all as specified and directed. |
| 18 | Material & Labour for rendering 15mm thick on fair faces of brick work in Cement Mortar 1:4 finished even & smooth without using extra cement complete all as specified and directed. |
| 19 | Material & Labour for preparing new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed. |
| 20 | Material & Labour for Rough cast plaster as specified. (Rendering coat not less than 10mm thick in Cement Mortar 1:3, while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg size 6 to 12mm mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even) complete all as specified and directed. |
| 21 | Material & Labour for 25mm thick cement concrete flooring type B-1, 1:2:4 using 20mm graded stone aggregate finished even and fair to receive the screed bed without using extra cement complete all as specified and directed. |
| 22 | Material & Labour for coloured Non-skid ceramic tiles 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc., set and jointed in neat cement slurry pointed in coloured cement to match including 15mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed. |
| 23 | Material & Labour for coloured glazed ceramic tiles as on vertical surface of the 450mm x 300mm x 7mm such as in skirting dado etc., set and jointed in neat cement slurry and pointed in coloured cement to match the surface with floor over and including 10 mm thick cement rendering in Cement Mortar 1:4 complete all as specified and directed. |
| 24 | Material & Labour for 20 to 25mm thick machine cut Kota stone (550mm x 550mm) flooring over cement screed base laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rubbing and Mirror polishing complete all as specified, including 15mm thick screed bed in Cement Mortar 1:4 complete all as specified and directed. |
| 25 | Aall as per item here-in-above but kota stone slab (100/150mm x 550mm) and 20-25mm thick in riser of steps, skirting, dados and pillar laid over and including 10mm thick rendering to receive the stone in cement mortar 1:3 and jointed, complete all as specified and directed. |
| 26 | Material & Labour for rolled mild steel framed work angle iron (40x40x6mm) as in door frame (chowkhat) including provn of 12mm dia deformed bar welded horizontally to bottom of frame Fe-410-W (Gde-E-250) quality -A including preparing back of chowkhat and applying two coats after & ending newly fair surface with clean sharp sand paper complete all as specified and directed. |
| 27 | Supply and fixing 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as per SSR part I, complete all as specified and directed. |
| 28 | Supply and fixing 35mm thick glazed and Skelton shutters to receive glass/gauge of 1st class Hard wood factory made shutter with sash bars for windows/ventilators fixed in position, SSR Part-I Sec 8 clause 8.20(B), complete all as specified and directed. |
| 29 | Supply and fixing steel window with side hung shutter including box type hinges with steel handle with glazing bar, complete all as specified and directed. |
| 30 | Supply and fixing steel window with side hung shutter including box type hinges with steel handle without glazing bar, complete all as specified and directed. |
| 31 | Supply and fixing steel windows or ventilators, fixed type, with glazing bars, complete all as specified and directed. |
| 32 | Supply and fixing 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. |
| 33 | Supply and fixing figured glass 3mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan, complete all as specified and directed. |
| 34 | Supply & fixing galvanized mild steel wire cloth 1.18mm average width of aperture and 0.56mm nominal dia of wire fixed with tinned tacks or galvanized wire staple, complete all as specified and directed. |
| 35 | Supply and fixing MS work as in grills grating etc., with ends of bars shouldered and riveted framed guard bars, barred iron doors, ladders conforming to FE 410-0 or 310-0, complete all as specified and directed. |
| 36 | Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. |
| 37 | Supply and fixing Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed. |
| 38 | Supply and fixing 100mm long butt hinges mild steel medium weight cold rolled ISI marked, complete all as specified and directed. |
| 39 | Supply and fixing 150mm long extruded aluminum handles fabricated type anodized, ISI marked, complete all as specified and directed. |
| 40 | Supply and fixing aluminium anodised barrel tower bolt of extruded section 150mm long, complete all as specified and directed. |
| 41 | Supply and fixing mild steel 300mm ordinary rat tail rod pattern springs (ISI marked) including roller and roller plate complete all as specified and directed. |
| 42 | Supply and fixing 300mm long mild steel sliding bolts, stove enamelled black, with bright bolt not less than 12mm dia complete all as specifed and as directed. |
| 43 | Supply & Fixing Floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor, complete all as specifed and as directed. |
| 44 | Materials and labour for preparation of new wooden surfaces of any description not otherwise described exceeding 10cm width or girth and applying two coats of synthetic enamels paints over a coat of pink primer, complete all as specifed and as directed. |
| 45 | Material & Labour for providing pre cast cement concrete 1:2:4, type B-1 using 20mm graded aggregate in manhole cover slab set in cement mortar 1:4, complete all as specifed and as directed. |
| 46 | Material & Labour for RCC M-25 (Design Mix) using 20mm graded stone aggregates in foundations, including rafts, footings, foundation beam, plinth beams, bases of columns etc. Basement slabs, under reamed piles and mass concrete, complete all as specifed and as directed. |
| 47 | Material & Labour for RCC M-25 (Design Mix) using 20mm graded stone aggregates in Columns, pillars, piers, posts and struts, complete all as specifed and as directed. |
| 48 | Material & Labour for RCC M-25 (Design Mix) using 20mm graded stone aggregates in beams, cantilevers, lintels etc., complete all as specifed and as directed. |
| 49 | Material & Labour for RCC M-25 (Design mix) using 20mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, complete all as specifed and as directed. |
| 50 | Material & Labour for Form work to sides of concrete foundations, footings bases of columns and plinth beams and similar works with fair finished surfaces of concrete, complete all as specifed and as directed. |
| 51 | Material & Labour for Formwork to sides of pillars, posts, struts, piers columns & stanchions,rough finished surface of concrete, flat with fair finished surface, complete all as specified and directed. |
| 52 | Material & Labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., with fair finished surface, complete all as specifed and as directed. |
| 53 | Material & Labour for Formwork to soffits of suspended slabs, such as roof slabs, floor slabs landing and similar work not exceeding 200mm thick (Horizontal & sloping) with fair finished surfaces complete all as specifed and as directed. Note- Steel props to be used. |
| 54 | Material & Labour for From work to edges of concrete flats treads breaks in floors, window cill concrete railing, opening in convert valley floor and roof exceeding 5 but not exceeding 10 cm wide and sides RCC/PCC band in walls with fair finished surface, complete all as specified and directed. |
| 55 | Material & Labour for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and directed. |
| 56 | All as per item here-in-above but 5mm dia and over up to and including 8mm dia in stirrups, complete all as specified and directed. |
| 57 | Material & Labour for rendering 15mm thick on RCC roof concrete surfaces in Cement Mortar 1 : 4 mixed with WPC @ 3 % by the weight of cement used and finishing even and smooth without using extra cement complete all as specified and directed. |
| 58 | Supply only water proofing compound, complete all as specified. |
| 59 | Material & Labour for 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate in roof surface, complete all as specifed and as directed. |
| 60 | Material & Labour for APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick reinforced with polyster non-woven fabric (wt not less than 150 gms/sqm) laid on primed surface by torch application including priming complete all as specifed and as directed. |
| 61 | Materials & Labour for 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, complete all as specified and directed, |
| 62 | Supply and fixing 20mm bore medium grade tube galvanised with all fittings and fixed complete to walls & ceiling or laid in floor, complete all as specified and directed. |
| 63 | Supply and fixing bib taps long shank 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe, complete all as specified and directed. |
| 64 | Supply and fixing 15mm bore CP Angle cock one way chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed, complete all as specified and directed. |
| 65 | Supply and fixing 15mm bore stop valve, cast copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed, complete all as specified and directed. |
| 66 | Supply and fixing swivel shower for PTMT with shower arm 195mm long with bend of 45 degree 15mm dia (minimum weight 80 gms), complete all as specified and directed. |
| 67 | Supply and fixing grating doom 100mm dia without waste hole of PTMT (Minimum weight 25 gms), complete all as specified and directed. |
| 68 | Supply and fixing PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed. |
| 69 | Supply and fixing bevelled edge mirror of 5 to 6mm thick select quality glass, 600mm x 450mm size, mounted on 6mm thick AC building board of commercial plywood and fixed to wooden plug with chromium plated brass screw and screw cup washer, complete all as specified and directed. |
| 70 | Supply and fixing rotational moulded polyetlene water storage tanks (Calendrical vertical with closed top) 500 ltrs cap hoisted and fixed in position, complete all as specifed and as directed. |
| 71 | Supply and fixing 20mm Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe, complete all as specifed and as directed. |
| 72 | Supply and fixing 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed, complete all as specifed and as directed. |
| 73 | Supply and fixing stainless steel tubular towel rail 20mm dia 600mm long, complete all as specifed and as directed. |
| 74 | Supply and fixing vitreous china wash basin, white, flat back, size 550mm x 400mm with 15mm dia pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, waste fitting of PTMT, PVC connection and PVC waste pipe and fixing with new brackets including cutting and pinning in ends of brackets, complete all as specified and directed. |
| 75 | Supply and fixing Vitreous china wash down water closet pan (pedestal pattern) white including connection to outgoing pipes and to flushing pipe, fixing of new Plastic water seat closet cover black/ white closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specifed and as directed. |
| 76 | Supply & Fixing Vitreous China urinals size of 465 x 355 x 265, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, complete all as specified and directed. |
| 77 | Supply and fixing PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan, complete all as specified and directed. |
| 78 | Supply and fixing PVC socketed rain water pipe with rubber ring joints 110mm dia fixed to wall, complete all as specified and directed. |
| 79 | Supply and fixing PVC socketed rain water pipe with rubber ring joints 75mm dia fixed to wall, complete all as specified and directed. |
| 80 | Supply and fixing PVC (SWR) bends any radius bore of 110mm, complete all as specified and directed. |
| 81 | Supply and fixing PVC ( SWR) bends any radius bore of 75mm, complete all as specifed and as directed. |
| 82 | Supply and fixing PVC (SWR) vent cowl bore 110mm, complete all as specifed and as directed. |
| 83 | Supply and fixing PVC (SWR) vent cowl bore 75mm, complete all as specified and directed. |
| 84 | Supply and fixing PVC (SWR) floor trap, plain with grating including jointing with solvent cement dia meter of out pipe 75mm, complete all as specified and directed. |
| 85 | Material & Labour for cement concrete bed to drain pipe including packing under haunchings of pipe after they are laid and tested in cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) bore of pipe 150mm, complete all as specifed and as directed. |
| 86 | Material & Labour for Reinforced concrete pipes, class NP-2, 150mm bore, laid and jointed complete with collars, complete all as specified and directed. |
| 87 | Cutting into existing man holes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channels (1/2 round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching, complete all as specified and directed. |
| 88 | Supply and fixing Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300 gms), complete all as specified and directed. |
| 89 | Supply and fixing Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 105 gms), complete all as specified and directed. |
| 90 | Supply and fixing steel work in tubular trusses including columns, special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1998 grade st-240, complete all as specified and directed. |
| 91 | Supply and fixing plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including welding etc., Fe-410-W(gde-E-250) quality B, complete all as specified and directed. |
| 92 | Supply and fixing mild steel bolts, purpose made with hexagonal or square head one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exceeding 30 cm long, diameter of neck exceeding 20mm and not exceeding 25mm, complete all as specified and directed. |
| 93 | Supply and fixing mild steel screws bolts 5 to 10 mm dia (machine made) with hexagonal or square heads at one end and screw the other or screwed both end to be fitted with washers and on hexagonal or square exceeding 5 cm but not exceeding 10 cm long, complete all as specified and directed. |
| 94 | Supply and fixing plain angle cleats for securing purlins to trusses or rafters and similar articles conforming to Fe-290 Gde E-165, complete all as specified and directed. |
| 95 | Materials and labour for preparation of new steel surface of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamels paints over a coat of red oxide primer, complete all as specified and directed. |
| 96 | Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed. |
| 97 | Supply and fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed. |
| 98 | Materials and labour for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed. |
| 99 | Materials and labour for 100mm thick cement concrete type D-2 1:4:8 (40mm graded aggregate) as in mass concrete and sub base, floors etc., complete all as specified and directed. |
| 100 | Materials and labour for sand cushioning layer for laying PCC interlocking paver block, complete all as specified and directed. |
| 101 | Materials and labour for 80mm thick machine pressed precast concrete interlocking paver block, coloured with glossy finish, any shape and size, M- 40 Grade, with grey cement and pigment, complete all as specified and directed. |
| 102 | Excavating over areas, not exceeding 1.5 Metre deep and getting out in soft /loose soil, complete all as specified and directed. |
| 103 | Excavating over areas, exceeding 1.5 Metre but not exceeding 3.0 Metre deep and getting out in soft /loose soil, complete all as specified and directed. |
| 104 | Excavating over areas, exceeding 3.0 Metre but not exceeding 4.5 Metre deep and getting out in soft /loose soil, complete all as specified and directed. |
| 105 | Removing excavated material exceeding 250 Metre and not exceeding 500 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point, complete all as specified and directed. |
| 106 | Materials and labour for RCC M-30 (Design Mix) as in Foundations, including rafts, footings, foundation beams; slant beams; bases for columns, etc. complete all as specified and directed. |
| 107 | Materials and labour for RCC M-30 (Design Mix) as in Walls, Retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed. |
| 108 | Materials and labour for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, complete all as specified and directed. |
| 109 | Supply & Fixing in 75mm bore PVC (SWR) pipes as in weep holes, complete all as specified and directed. |
| 110 | Materials and labour for using Graded coarse aggregate 20mm as in invert filter, complete all as specified and directed. |
| 111 | Materials and labour for using Graded coarse aggregate 63- 40mm as in invert filter, complete all as specified and directed. |
| 112 | Materials and labour for sand filling as in invert filter, and back filling etc. including watering and consolidation, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 113 | Materials and labour for sand filling as in invert filter, and back filling etc. including watering and consolidation, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysNov 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender