Tender For Repair / Maintenance To Various Washing Plant, Sign Board, Lightning Protection And Various Sizes Of Geysers, Solar Water Heaters, Solar Light Fitting And Petty Repair In Zone C And D Under Age E/M At Ge Jhansi
Tender Value
1.35 Crore
Estimated cost
Bid Submission
12 Nov 2026
10 days left
EMD
2.10 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jhansi → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Maintenance To Various Washing Plant, Sign Board, Lightning Protection And Various Sizes Of Geysers, Solar Water Heaters, Solar Light Fitting And Petty Repair In Zone C And D Under Age E/M At Ge Jhansi
BOQ
| Sl. No. | Item Description |
| 1 | Supply and fix single pointed copper rod 12 mm dia and 300mm long fixed on roof in and including all fittings, fixtures and PCC 1:2:4 type B-1 bolck 100mm x 100mm x 100mm complete all as specified and as directed |
| 2 | Supply and fix Galvanised Iron strip 32 x 6 mm burried in ground 150 mm below ground including all excavation and earth work connecting at ends, jointing etc complete all as specified and as directed. |
| 3 | M&L test point terminal bolck made of metal or phosphoras bronze of size 75 x75 x 25 mm of 6mm thick or copper strip of size 32 x 6mm, 100 mm long drilled and secrewd including 03 Nos 08mm dia 25mm hex head screw complete with box. |
| 4 | Supply and fix single pointed Aluminium rod 12 mm dia and 300mm long fixed on roof in and including all fittings, fixturres and PCC 1:2:4 type B-1 bolck 100mm x 100mm x 100mm complete all as specified and as directed |
| 5 | Supply and fix Aluminium strip 25 x3.15 mm with saddles and fixing screws etc for roof and down conductors above ground level complete all as specified and as directed. |
| 6 | Supply and fix Aluminium strip 32 x 6 mm burried in ground 150 mm below ground including all excavation and earth work connecting at ends, jointing etc complete all as specified and as directed. |
| 7 | M&L for earthing complete with copper earth plate electrode 600mm x 600mm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to copper strip 20x3 mm as earthing lead by means of bolts, nuts, check nuts and washers of copper and earth wire protected by 50mm dia GI pipe medium grade and connected to pole structure/ panel board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and as directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth strip up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II (b) Earthing result should be less than 3 Ohm required. |
| 8 | Material and labour for servicing of mechanical laundry with washing machine of whole system assembly including ,washer extractor(02 nos),drying tumbler(01 no),steam generator (01no) ,Air compressor,hydro extractor removing parts, applying blower to remove all dust, cleaning, washing, removing dirt, washing and cleaning of whole assembly system of the laundry the necessary parts and re-assembling the dismantled components, refixing to its original position and testing for proper functioning complete all as specified and as directed. Note -Defective compnents and parts will be repaired and replaced as per CA clause (under defect liability period )in which the system has been installed complete all as specified and as directed. |
| 9 | Supplying, installing, testing, and commissioning of Stored Pressure ABC Type Dry Chemical Powder Extinguisher of 6 kg capacity. Must conform to IS 15683 or equivalent international standards. Unit shall include a pressure gauge, discharge hose with nozzle, wall-mounting bracket, and initial charge of mono-ammonium phosphate-based powder. Installation includes grouting of MS flat brackets into the wall with necessary nuts and bolts complete all as specified and as directed |
| 10 | Supply, installation, testing, and commissioning of 25 kg capacity ABC-type (Dry Chemical Powder) fire extinguisher, trolley-mounted on a rugged MS wheel-based frame for easy maneuverability. The unit shall comprise a high-grade mild steel cylinder fabricated via MIG welding, conforming to IS 16018:2012. The extinguishing media shall be Mono Ammonium Phosphate (MAP 50% or 90%) powder as per IS 14609. The expulsion method shall be via an external 1 kg CO2 gas cylinder conforming to IS 7285. The assembly must include a minimum 3-meter long high-pressure discharge hose with a squeeze-grip nozzle, pressure gauge, and safety valve. The body shall be finished with anti-corrosive epoxy polyester powder coating in Signal Red (RAL 3000) complete all as specified and as directed |
| 11 | Supply and Installation of Fire Bucket Stand (4-Bucket Capacity) Fabrication of Main Stand made of Heavy Duty Mild Steel (MS) angle (i.e or 1\\" square tube) with 4 hooks for bucket hanging, height of min 6 ft.Protective Canopy/Shed fabricated from 18 SWG MS or Galvanized sheet to protect sand/water from rain/dirt, fire Buckets (9 Litre), 4 No, Galvanized Mild Steel fire buckets conforming to IS: 2546. Body thickness 1 mm with dished bottom and reinforced top rim, Painting and Marking, Anti-corrosive primer followed by two coats of Fire Red enamel paint, Centrally printed \\"FIRE\\" in black/white (75 mm high), Inside of buckets painted white complete all as specified and as directed |
| 12 | Supplying, installing, testing, and commissioning (SITC) of a 50 Liters Per Hour (LPH) Commercial Reverse Osmosis Water Purification System, including the following specifications and component , Purification Capacity: 50 Liters per hour, designed for a maximum duty cycle of approximately 500–600 liters per day. Filtration Technology: Multi-stage purification process (typically 5 to 6 stages) including: Stage 1: 5-micron PP Spun/Sediment filter for suspended particle removal. Stage 2: Granular Activated Carbon (GAC) filter for chemical and odour removal. Stage 3: Carbon Block filter for fine chemical filtration. Stage 4: High-rejection RO Membranes (typically 2 to 4 pieces of 150 GPD or 100 GPD) for 90–95% TDS reduction.Stage 5: Post-Carbon or UV Sterilizer for final polish and microbiological safety complete all as specified and as directed |
| 13 | Supply, installation, testing and commissioning of LED Glow Sign Board of size (5 x 3) foot fixing of double/single-sided glow sign board made of 18 SWG GI sheet with 7\\" depth. Includes 3mm white acrylic/polycarbonate face, Tata Steel box 5 Kg Iron frame ,LEd Power light, modules with IP67 protection, and branding with 3M vinyl mounting on Iron channel / angle / concrete grounding to be spray painted with anti-corrosive primer including electrical Work laying of 3-core 1.5 sqmm copper wire in 20mm heavy-duty PVC conduit for connecting signage to the nearest power point, including MCB and accessories complete all as specified and as directed |
| 14 | Supply, installation, testing and commissioning of LED Glow Sign Board of size (51 x 18) inch fixing of double/single-sided glow sign board made of 18 SWG GI sheet with 7\\" depth. Includes 3mm white acrylic/polycarbonate face, Tata Steel box 5 Kg Iron frame ,LEd Power light, modules with IP67 protection, and branding with 3M vinyl mounting on Iron channel / angle / concrete grounding to be spray painted with anti-corrosive primer including electrical Work laying of 3-core 1.5 sqmm copper wire in 20mm heavy-duty PVC conduit for connecting signage to the nearest power point, including MCB and accessories complete all as specified and as directed. |
| 15 | Supply, fabrication, and fixing of Retro-Reflective Overhead Safety Sign Board of size 6' x 4' made of 4mm thick ACP/Aluminium sheet, finished with high-intensity retro-reflective sheeting as per IRC:67. The board shall be mounted on 2 Nos. 90mm dia SS/MS poles with necessary base plates, including excavation and M15 concrete foundation work complete all as specified and as directed. |
| 16 | Supply, fabrication, and fixing of Retro-Reflective Overhead Safety Sign Board of size 4' x 3' made of 4mm thick ACP/Aluminium sheet, finished with high-intensity retro-reflective sheeting as per IRC:67. The board shall be mounted on 2 Nos. 90mm dia SS/MS poles with necessary base plates, including excavation and M15 concrete foundation work complete all as specified and as directed |
| 17 | Supply, Installation, and Commissioning of LED Scrolling Display Board (Size: 5x3 ft), LED Modules: P10 SMD Outdoor modules (320x160mm each), high brightness (4500+ nits), IP65 rated, Power Supply: 5V 40A/60A Slim SMPS with overload and surge protection.Controller Card: Wi-Fi/LAN/USB programmable controller with internal memory.Enclosure: Weatherproof MS/Aluminium cabinet with powder coating and front/rear maintenance access, Mounting Structure: MS frame/brackets for wall or pole mounting including installation hardware complete all as specified and as directed |
| 18 | Supply and Fixing of ACP LED Signage Board ACP Base of size 20 x 2 feet , Providing and fixing 3mm thick ACP (Aluminium Composite Panel) sheet of approved make (e.g., Aludecor, Alucobond) to be used as the background.Frame Structure Fabrication of a heavy-duty frame using M.S. hollow square tubes (approx. 16-18 gauge). The frame must be duly painted with anti-rust primer for durability, 3D Letters shall be made of 3mm thick high-grade Acrylic sheet (100% virgin monomer), Letters to be computerized laser or CNC cut with a side-depth (return) of approximately 2–3 inches. Illumination: High-quality LED modules (Samsung or equivalent make) with IP65 waterproof rating for outdoor use. Includes the supply of a suitable SMPS power supply/transformer and all necessary internal wiring.Installation: Includes all labor, scaffolding, and fixing arrangements at the site at a height as per requirement complete all as specified and as directed |
| 19 | Supply, installation, testing and commissioning of a 100 LPH Commercial RO Water Purifier system, complete with all internal filtration stages, high-pressure pumps, and control systems. The scope includes all necessary plumbing connections, electrical wiring, and a matching storage tank (typically 80–100 Litres) complete all as specified and as directed |
| 20 | Supply, Installation, Testing and Commissioning advance encapsulated compound based CPRI tested maintenance free, pipe-in-pipe technology upgraded (Zinc & Alloy Coated), ZINC COATED (80-100) microns with pure Zinc (99.9%) & ALLOY COATING (200-250) microns earthing system confirming IS 3034, outer and inner pipe 41.9mm dia and 26.4mm dia respectively, 2mtrs length, zinc coated with additional special Alloy coating 300mm on the topside for additional protection of the Terminal, annular space between the pipes filled up with COMPACT FILL (CF) (Crystalline Conductive compound) (COMPACT FILL (CF) mixture which is machine pressed in the pipes shall not disintegrate or collapse when outer pipes corrodes), inner pipe extended with terminals for connectivity, including digging the pits and refilling the same by Electrodite/ Conductolite backfill compound (Ground Enhancer), (BFC shall be eco-friendly and it shall not contain environmentally hazardous material /metal having ROHS Certification from NABL accredited lab), earth pit provided with a FRP earth pit cover for protection and safe guard of terminals, complete work executed all as per manufacturer's instructions complete all as specified and as directed.NOTES :- (i) In areas where soil condition is bad, good earth shall be arranged to fill the excavated pits by mixing the same with BFC 2 bags (as per soil condition) extra per pit/unit. The material shall have good electrical conductivity and anti corrosion property in wide range of soil conditions.(ii) The quantity of BFC \\"Electrode\\" shall be increased according to soil condition and to achieve the earth value less than 1 Ohm |
| 21 | M & L cleaning pruning of tree branches to improve structure, remove deadwood, or clear paths, including disposal of rubbish up to a distance of 50m outside the periphery of the STParea, DG Set Room, Store room, RAC Section Yard complete etc complete all as specified and as directed. |
| 22 | M & L 18 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for work stations etc of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed |
| 23 | M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and as directed |
| 24 | M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and as directed. Note :- (a) The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II. (b) Earthing result should be less than 3 Ohm required. Please Enable Macros to View BoQ information |
| 25 | M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and as directed. Note :- (a) The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II. (b) Earthing result should be less than 3 Ohm required. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender