Tender For Comprehensive Maintenance Of Certains Otm Bldgs Under Aor Of Age B/R-I At Hisar Mil Stn Under Ge (W) Hisar
Tender Value
45 Lakhs
Estimated cost
Bid Submission
02 Nov 2026
5 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hisar → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Comprehensive Maintenance Of Certains Otm Bldgs Under Aor Of Age B/R-I At Hisar Mil Stn Under Ge (W) Hisar
BOQ
| Sl. No. | Item Description |
| 1 | S&F, GI powder caoted snap grid of sizes 605 mm x 605 mm frame work for false ceiling with main tee 32x24x1mm thick, cross tee 26x24x1mm thick and wall angle 24x24x1mm thick, flange covered with PVC thin sheet including gypsum board 7-9 mm thick, duly finished surface (thin PVC layer on gypsum board as per manufacturer instructions) size 600mm x 600mm and the same to be placed in snap grid as in false ceiling and Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, including dismantling old framework and board any type, complete all as specified and directed. |
| 2 | S&F Hollow PVC Wall Lining consisting of 5mm thick wood grained printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame, including dismantling old wall panelling any type, complete all as specified and directed. |
| 3 | M&L for Machine cut kota stone slab flooring 18-20mm thick each over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with and including 15mm thick screed bed or bedding in cement mortar 1:6, including dismantling old existing stone slab or tiles any type, complete all as specified and directed. (Note : Single piece tiles will be placed on the surface of stair case tread area). |
| 4 | M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with in neat cement slurry and pointed in white or coloured cement to match over 10 mm rendering in cement mortar 1:6, including dismantling old existing stone slab or tiles any type, complete all as specified and as directed. |
| 5 | Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete. |
| 6 | M&L for light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6 as in floors, including dismantling old existing tiles any type, complete all as specified and as directed. |
| 7 | M&L for light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm rendering in cement mortar 1:6, including dismantling old existing tiles any type, complete all as specified and as directed. |
| 8 | M&L for light shade virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6, including dismantling old existing tiles any type, complete all as specified and as directed. |
| 9 | M&L for light shade virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in dado, skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm rendering in cement mortar 1:6, including dismantling old existing tiles any type, complete all as specified and as directed. |
| 10 | M&L for coloured joint free non-skid ceramic floor tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding of cement motor 1:6, including dismantling old existing tiles any type, complete all as specified and directed. |
| 11 | M&L for coloured glazed ceramic tiles in vertical surfaces 350 x 250 x 7mm / 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering of cement mortor 1:4, including dismantling old existing tiles any type, complete all as specified and directed. |
| 12 | Demolition of reinforced cement concrete and reinforcement cut as required to facilitate demolition above ground floors in any position complete all as specified and directed. |
| 13 | S&F Fe 410 -W (GdeE- 250) qualityA, rolled sections as in framing for chajjah, cooler stands, cladding, glazing and the like fixed with angle cleats and connecting plates, etc. complete all as specified and directed. |
| 14 | Dismantling asbestos cement (Corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed. |
| 15 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof coverimg/ cladding to wall, fixed with self tapping screws and making good all the disturbed surfaces of wall in CM 1:4 or cement concrete 1:3:6 complete all as specified and directed. |
| 16 | S&F 0.63 mm Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 fixed with self tapping screws complete all as specified directed. |
| 17 | Dismantling structural steel work including doors, gates but excluding framed truss etc, complete all as specified and directed. |
| 18 | S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed. |
| 19 | S&F rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-290 (Gde E-165) complete all as specified and directed. |
| 20 | S&F steel section embeding in concrete and screwing etc. wind ties for roof including securing bolts posts ans struts in fencing/pillar etc including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 21 | M&L preparation of new steel surfaces over 10cm in width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 22 | S&F 32mm dia 'medium grade' tubes galvanised, with all fittings and fixed complete to floors as spouts in sunken portions, including taking down old existing pipe, complete all as specified and directed. |
| 23 | S&F in repair vitreous china squatting pan \\"ORISSA\\" pattern size 580mm x 440mm, white with integral foot rest including cast iron 'P' or 'S' trap of 100 mm dia and connection to trap including cement concrete, and to flushing pipe, anti-syphonage pipe etc, including making good to floor, complete all as specified and directed. |
| 24 | S&F in repair water closet vitreous china water closet ‘Pedestal’ pattern white including cast iron 'P' or 'S' trap of 100 mm dia and connection to trap including cement concrete, and to flushing pipe, anti-syphonage pipe etc, including making good to floor, complete all as specified and directed. |
| 25 | S&F in repair 10 Litres capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float and handle including bracket complete all as specified and directed. |
| 26 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete complete all as specified and directed. |
| 27 | S&F in repairs seat cover for pedestal pattern WC, complete all as specified and directed. |
| 28 | S&F in repairs vitreous china wash basin counter top dome, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe and 15mm pillar tap cast copper alloy with capstan head chromium plated, complete all as specified and directed. |
| 29 | S&F in repair 32 mm bore, brass, chromium plated, bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed, complete all as specified and directed. |
| 30 | S&F in repairs waste pipe, PVC, low density polyethylene 32 mm dia, complete all as specified and directed. |
| 31 | M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and directed. |
| 32 | Supply & Laying of CPVC pipe, class-1 (SDR 11) ,15 mm nominal size & fittings on walls/ceiling, concealed or laying in floors, including taking down old existing pipe complete all as specified and directed. |
| 33 | Supply & Laying of CPVC pipe, class-1 (SDR 11) , 20 mm nominal size & fittings on walls/ceiling, concealed or laying in floors, including taking down old existing pipe complete all as specified and directed. |
| 34 | S&F in repair 15 mm bore, stop valve fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed. |
| 35 | S&F in repairs 15 mm bore, angle valves cast copper alloy chrome plated fancy type , cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions all as specified and directed. |
| 36 | S&F in repairs 15mm bore, bib taps, cast copper alloy with curtch or butterfly handle, screwed down, screwed for iron pipe of for brass ferrule fancy type, chormium plated, complete all as specified and directed. |
| 37 | S&F in repairs 15mm bore, pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and flynuts, screwed for iron pipe and fixed fancy type, complete all as specified and directed. |
| 38 | S&F in repairs 15mm bore, Brass L Bend CP mixer for mixing hot & cold water screwed down for iron pipe and fixed, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for iron pipe and fixed fancy type, complete all as specified and directed. |
| 39 | S&F in repairs PVC connections, 15mm size with PTMT nuts of length 450mm long, complete all as specified and directed. |
| 40 | S&F in repair chromium plated shower rose, fancy type with shower arm fixed to 15mm bore pipe, complete all as specified and directed. |
| 41 | S&F in repairs 20mm dia, D type, Brass chromium plated tubular towel rail, 60cm long between flanges chromium plated fixed to wall with screws, complete all as specified directed. |
| 42 | S&F 110 mm bore PVC (SWR) 'P' trap for fixing with WC complete all as specified and directed. |
| 43 | S&F 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 44 | S&F in repairs 110mm bore PVC (SWR) pipes single socketed, in any length with rubber rings joints fixed in walls for rainwater pipes complete all as specified and directed. |
| 45 | S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber rings joints fixed in walls for rainwater pipes complete all as specified and directed. |
| 46 | S&F for stacks clamps for 75mm/100mm bore pipe out of 50mm by 5mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall to roof complete all as specified and directed. |
| 47 | S&F 110mm bore PVC (SWR) bends, any radius, complete all as specified and directed. |
| 48 | S&F 110mm bore PVC (SWR) junction single (Single T) equal or unequal of any radius complete all as specified and directed. |
| 49 | M&L for tank cleaning and removing all scale and dirt etc. from tanks and from mouths of circulating pipes, by using bleaching powder etc. of capacity exc. 500 litre but n exc 1000 litre complete all as specified and directed. |
| 50 | S&F rotational moulded polythene water storage tank, triple layer and white in colour of 1000 litres capacity (cylindrical or verticla with closed top) hoisted & fixed in position (all as specified in SSR Part-I) including taking down old tank and removing to store, complete all as specified and directed. |
| 51 | S&F rotational moulded polythene water storage tank, triple layer and white in colour of 500 litres capacity (cylindrical or verticla with closed top) hoisted & fixed in position (all as specified in SSR Part-I) including taking down old tank and removing to store, complete all as specified and directed. |
| 52 | S&F 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142 gms/20mm - 210 gms/ 25mm-455 gms / 40mm-690 ) complete all as specified and directed. |
| 53 | M&L for treatment of sunken floor slab comprising of the following specifications with and including demolition of sunken floors complete all as specified and directed:-(i) Cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. Provision of 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout.(ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with and including integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by wt of cement consumed including filling it with water to check dampness and seppage and where dampness / seppage is noticed, nozzles shall be fixed and grouting carried out. (iii) All junctions points of side wall where CI/GI/PVC pipes are passing through shall be sealed with epoxy putty Sikaguard 694 F(I) or equivalent make in Fosroc / Thremax as approved by GE.(iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.(v) Applying two coats of polymer modified cementious water proof coating with Sika Topseal 107 or or equivalent make in Fosroc / Thremax as approved by GE in two coats @ 3kg/sqm to sanwiched with glass fibre reinforcemnt: Sika Fab-1 or or equivalent make in Fosroc / Thremax as approved by GE over base coat as per mnaufacturer's instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion.(vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound SIKA plastocreat plus or equivalent make in Fosroc / Thremax as approved by GE @ 0.2% by wt of cement consumed as per manufacturer's specification including rounding of corners and injuctions sloping towards spout. (vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint . Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. Test record for each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing and all M&L is inclued in the rates quoted above. |
| 54 | M&L for cement concrete type E2 1:5:10 (40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 55 | Taking down chowkats or frames not exc 1.5 sq.m area of each complete all as specified and directed. |
| 56 | Taking down chowkats or frames exc 1.5 sq.m, but not exc 4.0 sq.m, area of each (without taking off shutters form the frame) complete all as specified and directed. |
| 57 | Taking down shutters of any description exc 1.00 Sqm but n exc 2.00 Sqm each complete all as specified and directed. |
| 58 | S&F Fiber Glass Reinforced plastic (FRP)Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30mm thickness.The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs.The frame shall be covered with fiber glass from all sides.M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer complete all as specified and directed. |
| 59 | S&F door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire -retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer complete all as specified and directed. |
| 60 | S&F factory made single extruded WPC(Wood polymer compsite)solid door window/ceosetory windows & other frames/chowkats of size 45 x 85mm comprising of virgin PVC polymer of K value 58-60(suspension grade calcium carbonate and natural fibers (wood powder/rise husk and non toxic additives (maximum toxicity index of 12 for 100gms fabricated with miterd joints after applying with PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum,screw withdrawl strength of 2200N (face) & 1100N (edge) ,minimum comp ressive strength of 58 n/mm2 ,modules of elasticity 900n/mm2 and ressisistance to spread of flame of class A category with property of being termite/borrer proof ,water /moisture proof and fire retirdent and fixed in position with MS hold fast /Lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 61 | S&F factory made single extruded WPC(Wood polymer compsite)solid door window/ceosetory windows & other frames/chowkats of size 65x100mm comprising of virgin PVC polymer of K value 58-60(suspension grade calciumcarbonate and natural fibers (wood powder/rise husk0 and non toxic additives (maximum toxicity index of 12 for 100gms fabricated with miterd joints after applying with PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum,screw withdrawl strength of 2200N (face) & 1100N (edge) ,minimum comp ressive strength of 58 n/mm2 ,modules of elasticity 900n/mm2 and ressisistance to spread of flame of class A category with property of being termite/borrer proof ,water /moisture proof and fire retirdent and fixed in position with MS hold fast /Lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 62 | S&F factory made single extruded WPC(Wood polymer compsite)solid door window/ceosetory windows & other frames/chowkats of size 65x125mm comprising of virgin PVC polymer of K value 58-60(suspension grade calciumcarbonate and natural fibers (wood powder/rise husk0 and non toxic additives (maximum toxicity index of 12 for 100gms fabricated with miterd joints after applying with PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum,screw withdrawl strength of 2200N (face) & 1100N (edge) ,minimum comp ressive strength of 58 n/mm2 ,modules of elasticity 900n/mm2 and ressisistance to spread of flame of class A category with property of being termite/borrer proof ,water /moisture proof and fire retirdent and fixed in position with MS hold fast /Lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 63 | S&F factory made single extruded WPC (wood polymer composite ) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (suspension grade ),calcium carbonate and natural fibres (wood powder/rice husk /wheat husk )and toxic additives (maximum toxicity index of 12 for 100gms ) having miniumum density of 650 kg/cum and screw withdrawl strength of 1800N (face) & 900N (Edge ), miniumum compressive strength 50N/mm2,modulus of elasticity 850 N/mm2 and resisitance to spread of flame of class A category with property of being termite / borer proof ,water/moisture proof and fire retardant .WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S S screws complete all as specified and directed. |
| 64 | S&F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive glass, gauge etc (withsash bars) edges but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as specified in SSR Part-I Section 8 Clause 8.24(a), fitted to chowkats complete all as specified and directed. |
| 65 | M&L Framed work such as grills, gratings, gates etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, hand rails, cupboards frame and similar work con- forming to Fe.290.Gde-E-165 with and including necessary cutting and welding complete all as specified and directed. |
| 66 | S&F Sheet glass 4.00mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed. |
| 67 | S&F 4 mm thick figured glass fixed with and including necessary rubber gasket and aluminium beading complete all as specified and directed. |
| 68 | S&F Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 69 | S&F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 70 | S&F 300 mm long aluminium, alloy, anodised and fixed complete all as specif, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed and directed. |
| 71 | S&F 100mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21complete all as speicified and directed. |
| 72 | S&F 200 mm long aluminium handles, fabricated type, anodised complete all as speicified and directed. |
| 73 | S&F Mild Steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. |
| 74 | S&F Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 75 | S&F Powder coated aluminium door, shutters/partition, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.Note : (i) Glass panes and wire cloth shall be measured & paid separately . (ii) Rubber beading will not be weighed and not to be paid seperately. |
| 76 | S&F Powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. incl provision of cooler opening complete all as specified and directed. |
| 77 | S&F in repair door closer hydraulically regulated of Aluminium (extruded section body), designation No 2, universal type, suitable for door shutter of 701 to 850mm in width and of weight between 36 to 60 Kgs complete all as specified and directed. |
| 78 | S&F in repair double action floor spring, hydraulically regulated made up of minimum 1.25 mm thick, aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel, heavy duty, complete all as specified and directed. |
| 79 | S&F in repairs brass Mortice lock,vertical type, 4 lever size 100 mm complete all as specified and directed. |
| 80 | S&F 3mm thick acrylic sheet in squares exc 0.5 sq m each pane complete all as specified and directed. |
| 81 | S&F sheet glass 4.8 mm thick ordinary quality in squares exc 0.5 sq m each pane complete all as specified and directed. |
| 82 | M&L rendering 10 mm thick on fair faces or other than fair faces of brick or concrete surfaces built in cement mortar 1:4 and finished even and smooth (without using extra cement) including taking down existing plaster, complete all as specified and directed. |
| 83 | M&L rendering 05 mm thick on fair faces or other than fair faces of brick or concrete surfaces in ceiling built in cement mortar 1:3 and finished even and smooth (without using extra cement) including taking down existing plaster, complete all as specified and directed. |
| 84 | M&L including preparation of new plastered surface of ceiling with three coat of white wash, complete all as specified and directed. |
| 85 | M&L for preparation of new plastered surfaces of wall and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour with roller over a coat of acrylic water based interior grade primer @ 0.90 Litre/10 Sqm (undulated Surfaces) diluted with water in ratio interior grade primer and water (1:1) to be applied with roller for painting of subsequent coats over Acrylic readymade wall care putty @ 1.00 Kg/Sqm (undulated Surfaces) of average thickness 2mm over the plastered/old prepared painted surface of walls and sanding of the putty surface with mechanical wall sander complete all as specified and directed. |
| 86 | M&L including preparation of old surface of ceiling and applying two coat of white wash complete all as specified and directed. |
| 87 | M&L for complete removal of existing treatment of painted internal walls including pillars etc by mechanical equipments like electric wall sander/water jet machine and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour with roller over a coat of acrylic water based interior grade primer @ 0.90 Litre/10 Sqm (undulated Surfaces) diluted with water in ratio interior grade primer and water (1:1) to be applied with roller for painting of subsequent coats over Acrylic ready made wall care putty @ 1.00 Kg/Sqm (undulated Surfaces) of average thickness 2mm over the plastered/old prepared painted surface of walls and sanding of the putty surface with mechanical wall sander complete all as specified and directed. Please Enable Macros to View BoQ information |
| 88 | M&L for complete removal of existing treatment of painted internal walls including pillars etc by mechanical equipments like electric wall sander/water jet machine and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour with roller over a coat of acrylic water based interior grade primer @ 0.90 Litre/10 Sqm (undulated Surfaces) diluted with water in ratio interior grade primer and water (1:1) to be applied with roller for painting of subsequent coats over Acrylic ready made wall care putty @ 1.00 Kg/Sqm (undulated Surfaces) of average thickness 2mm over the plastered/old prepared painted surface of walls and sanding of the putty surface with mechanical wall sander complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender