Tender For Infrastructure Development Project At Gauhati University, Assam (Package-Ii)
Tender Value
12.29 Crore
Estimated cost
Bid Submission
04 Nov 2026
7 days left
EMD
24.58 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kamrup Metro → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Infrastructure Development Project At Gauhati University, Assam (Package-Ii)
BOQ
| Sl. No. | Item Description |
| 1 | CIVIL WORKEarth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :\\"1:4:8 (1 cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size drived from natural sources). |
| 5 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 6 | Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 7 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole :With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 8 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same. |
| 9 | Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.Upto and including 12mm dia. |
| 10 | Steel reinforcement for R.C.C. work ready to use \\"cut and bend\\" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 11 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 12 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make |
| 13 | Providing & Grouting of dowel tubes / Shear keys / Joints of precast members with M-60 grade cementitious grout (Non Shrink) of approved make by suitable means ( Free flowing / pump),curing etc. Complete as per directions of Engineer-incharge. (The payment shall be made on the basis of actual weight of approved grout injected.)Stirrer mixed cementitious grout (non shrink) of approved make in dowel tubes / Shear keys / Joints of precast members. |
| 14 | Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge. |
| 15 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. without disturbing the other structural elements.Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 16 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. without disturbing the other structural elements such as column, beams & slab. |
| 17 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar |
| 18 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :Of area beyond 3 sq. metres |
| 19 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm |
| 20 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :Thickness above 10 mm up to 25 mm |
| 21 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 22 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 23 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 24 | Centering and shuttering including strutting, propping etc. and removal of form for all heights :Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 25 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 26 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 27 | Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete.Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth levelConcrete of M30 grade with minimum cement content of 330 kg/cum |
| 28 | Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete.Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V levelConcrete of M25 grade with minimum cement content of 330 kg/cum |
| 29 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement Mortar 1:6 (1 cement : 6 coarse sand). |
| 30 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 31 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) |
| 32 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 33 | Providing and fixing ISI-marked flush door shutters conforming to IS 2202 (Part I), non-decorative type, block board core with first-class hardwood frame and matched commercial 3-ply veneering on both faces.35 mm thick, including ISI-marked stainless-steel butt hinges with necessary screws |
| 34 | Providing and fixing bright-finished brass tower bolts (barrel type) with necessary screws, complete. 250x10 mm |
| 35 | Ceiling-height partition consisting of G.I. frame and required board, including special-section power pressed/roll-formed G.I. sheet with zinc coating of 120 gms/sqm, floor and ceiling channels, vertical studs, dash fasteners/anchors, boards fixed on both sides with dry-wall screws, staggered joints and all necessary M.S. fixing complete. 75 mm overall thickness partition with 12.5 mm thick double-skin fire-rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS 2095 Part 3 (board with BIS certification marks) |
| 36 | MODULAR KITCHEN/PANTRY CABINETProviding and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately |
| 37 | Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge. |
| 38 | Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. |
| 39 | Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. |
| 40 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge. |
| 41 | Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in-charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately) |
| 42 | Providing and fixing 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge. |
| 43 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: |
| 44 | Providing and fixing M.S. tubular frames for doors, windows, ventilators and cupboards with rectangular/L-type sections, made of 1.60 mm thick M.S. sheet, joints mitred, welded and ground finished, with profiles of required size, including necessary butt hinges and screws and one priming coat of approved steel primer. Fixing with carbon-steel galvanized dash fastener of required diameter and size (to be paid for separately) |
| 45 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 46 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 47 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.40mm thick with 20mm nominal size stone aggregate. |
| 48 | 38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete. DSR-11.34 |
| 49 | Supply and fixing of 6 mm Carpet Flooring (color and design as per client’s choice) duly fixed on finished floor using SR998 resin adhesive. |
| 50 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 51 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 52 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed vitrified floor tiles polished finish of sizeSize of Tile 600 x 600 mm |
| 53 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed vitrified floor tiles polished finish of sizeTile 600 x 1200 mm |
| 54 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of sizeSize of Tile 600 x 600 mm |
| 55 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 56 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 57 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 58 | 12mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) |
| 59 | 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) |
| 60 | 6 mm cement plaster to ceiling of mix : 1:3(1 cement: 3 coarse sand) |
| 61 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 62 | Providing & fixing galvanized low carbon wire, anealed wire Chicken mesh formed by twisting two adjacent wires at least four times, forming a hexagonal shaped strong honeycomb mesh structure on joints of RCC & Brick work before plastering, of required gauge (not less than 21 gauge)and size with nails etc. complete as specified in drawing and as per the Direction of Engineer-in-charge. |
| 63 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 64 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats. |
| 65 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 66 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer |
| 67 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 68 | Fixing chowkhats in existing openings, including embedding in floors or walls, cutting masonry for holdfasts, embedding holdfasts in cement-concrete blocks, applying two coats of approved wood preservative, making good damage and disposing of rubbish, complete as directed by the Engineer-in-Charge. Door chowkhats |
| 69 | Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes for hot and cold water supply, including CPVC plain and brass-threaded fittings, solvent-cement jointing, trenching, refilling and testing of joints, complete. 25 mm nominal dia pipes |
| 70 | Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes for hot and cold water supply, including CPVC plain and brass-threaded fittings, solvent-cement jointing, trenching, refilling and testing of joints, complete. 32 mm nominal dia pipes |
| 71 | Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes for hot and cold water supply, including CPVC plain and brass-threaded fittings, solvent-cement jointing, trenching, refilling and testing of joints, complete. 80 mm nominal dia pipes |
| 72 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built-up standard tubular / Z sections and approved sections conforming to IS 733 and IS 1285, fixed with dash fasteners, EPDM/neoprene gaskets, cleats, snap beading and screws, complete as per architectural drawings; glazing, panelling and dash fasteners paid separately. For fixed portion Transparent or dyed to required shade according to IS 1868; minimum anodic coating grade AC 15 |
| 73 | For shutters of doors, windows and ventilators, including hinges/pivots, provisions for fittings and EPDM/neoprene gaskets; fittings to be paid separately. Transparent or dyed to required shade according to IS 1868; minimum anodic coating grade AC 15 |
| 74 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight notless than 12.50 kg/sqm) |
| 75 | Filling the gap between aluminium frame and adjacent RCC/brick/stone work with approved weather-silicone sealant over backer rod, complete as per architectural drawings and Engineer-in-Charge directions. Up to 5 mm depth and 5 mm width |
| 76 | Supply and fixing of Wooden Acoustical Doors 60mm Thick for STC 37 with necessary hardwares of the following specifications and as per the final drawings. The Door frame shall he of l35mmx70mm section Hard Wood, including making necessary grooves for fixing of hollow bulb type EPDM Gasket on the rebates. The core of the door shutter shall he made out of hardwood, ply and MDF, filled with resin bonded rockwool of 64kg/m3 density with 3mm thick sound dampening layer. Having Fire Retardant calcium cilicate boards and fire seals to comply 120 minuted fire rating as per BS-476 Part 20 & 22, along with fire rated 12 mm thick ply board for MICA Laminate finish. Shutter shall have wooden lipping Edge. Thickness of the shutter 60mm. The door assembly shall be fixed to the door frame with heavy duty stainless steel hardwares. Shutters shall be fixed with SS Hinges. The job shall include Provision of Hinges, Mortice Lock one side key and one side knob, Door Stopper & Drop Down Seal. All hardware as per approved by Architect and provide by client. |
| 77 | Supply and fixing of 32 KG density of 50 mm thickness underdeck insulation with aluminium lining on one side duly fixed with chicken mesh to completely cover the ceiling for acoustic and heat insulation. |
| 78 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing. |
| 79 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board |
| 80 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 81 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:G.S. Sheet |
| 82 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/ m² |
| 83 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.fourth and final layer of brick tiling with cement mortar (which will be paid for separatelyFor the purpose of measurement the entire treated surface will be measured. |
| 84 | Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) |
| 85 | Supply & installation of Wooden Slats made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers), backlined with Soundtexblack acoustical fleece, tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128x2440x16mm, volume density of base board 800Kg/m3, weight 8Kgs/m2 (L16), 10.5Kgs/m2 (L32), installed by using Anutone Strut framework system. • Fire (Class) – 1 & P (For FR grade), • Acoustics – NRC 0.77 (For E300* Mounting), • Thermal conductivity (W/mk)– na, • Climate (°C, RH) – 50, 70, • Light reflectance (%) – 75 (Maple Arce), • Green (VOC, RC %) – Low, 25. The Wooden slats will be backed by 50MM, 1000GSM Polyfiber Wool. |
| 86 | Providing and fixing of Stage Flooring/Dias Frame Work for stage flow shall be fabricated by using 100 mm high x 50 mm wide wooden battens (preferably teak / gumsal or equivalent) fixed over stage floor base at 600 mm centres in both directions using suitable fasteners. Wooden plank of size 125mm x 1850 mm and thickness 25 mm to be installed above the wooden battens. The planks shall be provided with tongue & groove joints required for locking. Including anti-termite treatment for wood, paint and wood polish work. |
| 87 | Panelling at all heights with integral densified calcium silicate panels/tiles of size 595x595 mm, having NRC (Noise Reduction Coefficient) of 0.50 minimum as per IS 8225:1987, light reflectance of 85% minimum, non-combustible and fire-performing construction, humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991; comprising specially fabricated galvanized mild steel framing, vertical studs and floor/ceiling channels at specified centres, 50 mm glass wool infill and screw-fixed calcium silicate non-combustible panels/tiles complete. With 15 mm thick fully perforated square/butt-edge lightweight calcium silicate panels/tiles |
| 88 | Providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595 mm of approved texture, design and pattern. The tiles should have humidity resistance (RH) of 99%, light reflectance 85%, thermal conductivity k = 0.052-0.057 W/m K, and fire performance as per BS 476 pt. 6 & 7; suspended in true horizontal level on an interlocking T-grid of hot-dipped all-round galvanized iron section of 0.33 mm thickness (galvanized @ 120 gsm), comprising main T runners 15x32 mm x 3000 mm, cross T 15x32 mm x 1200 mm and secondary cross T 15x32 mm x 600 mm to form a 600x600 mm grid; suspended using galvanized mild steel items, M-6 dash fasteners, threaded hanger rods and L-shape level adjusters; complete with GI perimeter wall angle fixed to the wall with plastic rawl plugs at 450 mm centres. With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6) |
| 89 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge25 mm average thickness |
| 90 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make |
| 91 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 92 | Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatiouswaterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge |
| 93 | Acoustic Wall WorksCeiling:-Supply and installation of 12.5 mm thick Perforated Gypsum Plaster Board of 3.5 mm square perforations (minimum 13% of perforated area) backed with 50mm thick approved 1000 GSM polyester wool. Ceiling frame work shall be backlined by using polyester wool having a density of 1000 GSM and 50mm thick. Overall depth of the system should be kept minimum 300mm. Framework shall consists of GI perimeter channels of size 0.45 mm thick (having one flange of 20mm and another flange of 30mm) fixed along with perimeter of the beam or walls with the help of nylon sleeves and screws at 600mm c/c. Then suspend GI main channels of size 0.45 mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1200mm c/c by using soffit angle of size 25mm x 10mm x 0.45mm thick fixed to true ceiling by using suitable fasteners. Cross channels of size 0.45mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the main channel with the help of connecting clips and in a direction perpendicular to the main channel at 300mm c/c. |
| 94 | Ceiling:-Supply and installation of 12.5mm thick plain gyspum plaster board Suspended by using C System which includes Main channel at every 1200mm . The Gypsum Board will be backlined by 50MM 1000 GSM Polyfiber Wool. Frame work shall consists of GI perimeter channels of size 0.45mm thick (having one flange of 20mm and another flange of 30mm) fixed along with perimeter of the gypsum or walls with the help of nylon sleeves and screws at 600mm c/c. Then suspend GI main channels of size 0.45 mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1200mm c/c by using soffit angle of size 25mm x 10mm x 0.45mm thick fixed to true ceiling by using suitable fasteners. Cross channels of size 0.45mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the main channel with the help of connecting clips and in a direction perpendicular to the main channel at 300mm c/c. The Gypsum board will be painted as per selected colour and shade. |
| 95 | Hall Lower Portion:-Supply & installation of Wooden Slats made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers), backlined with Soundtexblack acoustical fleece, tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128x2440x16mm, volume density of base board 800Kg/m3, weight 8Kgs/m2 (L16), 10.5Kgs/m2 (L32), installed by using Anutone Strut framework system. • Fire (Class) – 1 & P (For FR grade), • Acoustics – NRC 0.77 (For E300* Mounting), • Thermal conductivity (W/mk)– na, • Climate (°C, RH) – 50, 70, • Light reflectance (%) – 75 (Maple Arce), • Green (VOC, RC %) – Low, 25. The Wooden slats will be backed by 50MM, 1000GSM Polyfiber Wool. |
| 96 | Rear Wall above Balcony Upper Portion:-Supply and installation of Fabric Covered wood wool panel of size 1200 x 600 x 20mm mounted on supplied G I Frame work consisting of basic profile, main profile & edge profile. Frame work consists of 25mm thick GI wall channels with fully knurled surface of 0.45mm thick 80mm width, having two equal flanges of 26mm. A GI wall channel is fixed to the walls in horizontal direction with the help of suitable fastners at 600mm C/C then an another 25mm thick GI wall channel is fixed vertically over the horizontlly laid wall channel at 600mm C/C . The frame work shall wood wool panel will be back lined by using 50MM polyester wool having a density of 1000 GSM and 50mm thick. |
| 97 | Rear Wall above Balcony Lower Portion:-Supply & installation of Wooden Slats made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers), backlined with Soundtexblack acoustical fleece, tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128x2440x16mm, volume density of base board 800Kg/m3, weight 8Kgs/m2 (L16), 10.5Kgs/m2 (L32), installed by using Anutone Strut framework system. • Fire (Class) – 1 & P (For FR grade), • Acoustics – NRC 0.77 (For E300* Mounting), • Thermal conductivity (W/mk)– na, • Climate (°C, RH) – 50, 70, • Light reflectance (%) – 75 (Maple Arce), • Green (VOC, RC %) – Low, 25. The Wooden slats will be backed by 50MM, 1000GSM Polyfiber Wool. |
| 98 | Forestage:-Supply and installation of 150mm wide 12mm thick Laminated plywood. Frame work consists of 25mm thick GI wall channels with fully knurled surface of 0.45mm thick 80mm width, having two equal flanges of 26mm. A GI wall channel is fixed to the walls in horizontal direction with the help of suitable fastners at 600mm C/C then an another 25mm thick GI wall channel is fixed vertically over the horizontlly laid wall channel at 600mm C/C. |
| 99 | Wooden Beading on Wall:-Supply and Fixing of Wooden Beading by using 50X50MM Teak Wood with One side curve duly polished. |
| 100 | Stage Flooring:-Providing and fixing of Stage Flooring. Frame Work for stage flow shall be fabricated by using 100 mm high x 50 mm wide wooden battens (preferably teak / gumsal or equivalent) fixed over stage floor base at 600 mm centres in both directions using suitable fasteners. Wooden plank of size 125mm x 1850 mm and thickness 25 mm to be installed above the wooden battens. The planks shall be provided with tongue & groove joints required for locking. Including anti-termite treatment for wood, paint and wood polish work. |
| 101 | FURNITURE Works:Supply and Installation of Push Back Chair and Auto Tip Up with Synchronize System and ERW metal Pipe structure. It has Plastic Tray in seat and Back. |
| 102 | TableMain Table Size :- 1500(W) x 700(D) x 750(HT.)mm2D+1F Mobile Pedestal Unit Size :- 400(W) x 450(D) x 550(HT.)mmSpecifications :- Supplying & Placing cabin table with side unit that is to be assembled at site. The top & gablend to be made up of 25mm thick Pre-laminated particle board of grade II ofIS 12823 & Europien Standard EN 13986 with approved laminate and finish as per approved shade with 2mm thick PVC edge bending duly pasted with the assistance of edge banding machine at 200 degree Celsius. The front modesty to be made up of 18mm thick PLPB of grade II ofIS 12823 & Europien Standard EN 13986 with approved laminate and finish as per approved shade with 2mm thick PVC edge bending duly pasted with the assistance of edge banding machine at 200 degree Celsius. Wire manager cap without switch & sockets to be placed on top with metal powder coated wiring carrier tray below table top for arranging wires for electricity & data and metal wire riser carrier for raising wires from floor. The unit is to be provided with 2D+1F mobile pedestal unit of Size :- 400(W) x 450(D) x 550(HT.)mm. The Pedestal unit is to be made up of 18mm thick structure in prelam particle board with 2mm thick PVC edge banding finish with as per approved laminate color. The unit having 2D+1F drawers provisions. The unit is provided with front finger grooves opening & key locking system. The Pedestal unit is provided with castors for mobility. The manufacturer shall have quality and safety assurance like AFC provide declaration and test certification for VOC emission limits and other compound threshold. AFC manufacturing unit is certified by BIFMA, FSC, AIOTA, IGBC,ISO9001-QMS,14001-EMS, 450001-OHSAS (ACCREDIATED BY NABCB, Greenguard Compliance & ISO50001 (EMS).APRROVED MAKE : AFC, STEELCASE , HERMANMILLER |
| 103 | Mid Back Chair (Model :- AFC Fluid-X) Specifications :- Providing and supplying Medium back chair with ergonomic design. The seat shall be made up of 15mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam with fabric tapestry and the back shall be made up of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The base of the seat shall be supplied with PP cover and the backrest shall be made by keeping the natural curvature of the spine and adjustable lumbar support which helps to provide full back support. The chair shall be supplied with 1D adjustable polyurethane armrest. For seating durability, the chair shall have auto weight sensing tilt 360 degree revolving mechanism. The pedestal should have five legged nylon base having pitch circle dia. 660 mm fitted with 5 nos. twin wheel nylon castors. The manufacturer shall have quality and safety assurance like AFC provide declaration and test certification for VOC emission limits and other compound threshold. AFC manufacturing unit is certified by BIFMA, FSC, AIOTA, IGBC,ISO9001-QMS,14001-EMS, 450001-OHSAS (ACCREDIATED BY NABCB, Greenguard Compliance & ISO50001 (EMS). APRROVED MAKE : AFC, STEELCASE , HERMANMILLER |
| 104 | Supplying & Placing Library Chair ergonomically designed for user comfort & shall have aesthetically appealing design. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam having density 48kg/m³ with fabric tapestry of 300 GSM and the back shall be made of polypropylene. The arm shall be provided MS chrome plated having Dia. 22mm with PU on top for comfort and the armrest shall be used PP arm completely joint with seat. Polypropylene folding writing pad shall be provided. The frame structure shall be four legged support type made up of chrome plate round pipe of Dia 22 mm with 1.5mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like AFC provide declaration and test certification for VOC emission limits and other compound threshold. AFC manufacturing unit is certified by BIFMA, FSC, AIOTA, IGBC,ISO9001-QMS,14001-EMS, 450001-OHSAS (ACCREDIATED BY NABCB, Greenguard Compliance & ISO50001 (EMS). APRROVED MAKE : AFC, STEELCASE , HERMANMILLER |
| 105 | Providing, supplying, fabricating and installing furnishing works for the Seminar Hall at K.K.H. Library and Extension of Refreshment Area, complete as per tender drawings, approved designs and actual site requirements which as not Covered in above quantity or specifications, including all necessary materials, accessories, fixing hardware, labour, tools, transportation, installation, protection and final cleaning. All materials, colours, finishes, samples and shop drawings shall be submitted for the Client’s approval prior to procurement and execution. The work shall be executed in accordance with the approved drawings and directions of the Client/Engineer-in-Charge. |
| 106 | STAGE LIGHTING:SITC of LED PARCAN LIGHT Supply and installation of CE Certified 200W LED PARCAN Light with latest RDM technology for user friendly operation.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 107 | SITC of LED BLINDER LIGHT Supply and installation of CE Certified 4x100W LED Wash Effect Light with latest RDM technology for user friendly operation with below specifications.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 108 | SITC of 54 x 3W PAR RGBW LIGHT Supply and installation of CE Certified 120W LED RGBW Light with latest RDM technology for user friendly operation.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 109 | SITC of LED PROFILE LIGHT Supply and installation of CE Certified 300W LED Profile Spot Light with latest RDM technology for user friendly operation.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 110 | SITC of 54 x 3W PAR 3200K LIGHT Supply and installation of CE Certified 120W LED Warm White Light with latest RDM technology for user friendly operation (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 111 | SITC of LED PC SPOT LIGHT Supply and installation of 200W LED PC Spot Light with latest RDM technology for user friendly operation (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 112 | SITC of LED FRESNEL LIGHT Supply and installation of Fresnel spot light.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 113 | SITC of LED MOVING HEAD LIGHT Supply and installation of CE Certified 300W LED HYBRID MOVING (Beam, Spot & Wash Effect) Light with RDM protocol and Hi grade plastic body black color .(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 114 | SITC of LED RGBW CYCLORAMA WASH LIGHT Supply and installation of CE Certified 300W LED HYBRID MOVING (Beam, Spot & Wash Effect) Light with RDM protocol and Hi grade plastic body black color .(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 115 | C-ClampsSupply and installation of Die cast Aluminium C - Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish and safe working load of 100kg (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 116 | Safety BondSupply and installation of Safety bond with lock clip 1.5 Mtr Long made with twisted pair of GI wire rope, 2mm or 3mm Thickness with sleeve to be fixed around the grid to avoid fall of the material in case if the \\"C\\" clamp is not locked properly. SWL 1S0Kgs.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 117 | Identification Name PlateSupply and installation of 79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 118 | C Track Supply and installation of MS C track of size 50 x 40 mm size with 3mm thickness or higher size, Self-weight 3.3Kg per mtr. (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 119 | Customized SuspenderSupply and installation of Customized MS Suspenders made up of • MS fish plate 150 x 150 x 6 mm with hardware's if required as per site condition • MS Angle 40 x 40 x 5 mm or higher size required length as per site condition to Hold the \\"C\\" track rigidly held With SWL of 200kg. (As per site requirement). • Height adjustable M12 stud of suitable length as per site requirement along with suitable hardware's with pipe coupler clamp. (As per site requirement). (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 120 | Fixed Stage Light BarSupply and installation of Fixed Stage Light Bar, length 8.5 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish. (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 121 | Motorised FOH Light BarSupply and installation of CE Certified Motorised FOH Light bar Suitable Length 11 Mtrs as per site requiremnents, Suitable Capacity 3 Phase AC Motor with DC Brake & Gear box with black epoxy polyester powder coated .(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 122 | Stage Side Lighting LadderSupply and installation of MS Side Lighting Ladder of suitable length and Width (Min 2400 mm Height & 600 mm Width) (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 123 | Lighting Junction BoxSupply and installation of MS Fabricated 4 way 10A, 250V A.C, IEC, Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 124 | Splitter & Console Junction BoxSupply and installation of MS Fabricated 2 way 10A, 250V A.C, IEC, Junction box made up of 22SWG CRCA |
| 125 | DMX Signal IN Junction BoxSupply and installation of MS Fabricated S pin DMX Signal IN Junction box fitted with 5 pin DMX Male socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 126 | DMX Signal OUT Junction BoxSupply and installation of MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 127 | DMX Signal Loop Junction BoxSupply and installation of Fabricated 5 pin DMX Signal loop Junction box fitted with 5 pin DMX Male & Female socket with 0.3 Mtr DMX Loop cable fitted with 5 pin DMX cable mount plug, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement .(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 128 | Power Distribution BoxSupply and installation of Well designed Direct Lighting Distribution Board made up of CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt texture finish consists of R, Y, B Indicator lamp, SP Mcb's and for the junction boxes fixed on the top of the light bar including wiring and busbar connection with proper earthing and Hingable door with magnetic door lock complete .(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 129 | Auxiliary Marshalling BoxSupply and installation of Auxiliary marshalling box for power and signal cable termination in grid level and in Light bar.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 130 | Motor Cable Termination BoxSupply and installation of Motor Cable Termination box for power cable termination at grid level. (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 131 | Supply and installation of MS Fabricated Combined Motor Control Center panel cum Remote Control panel for Light bar system made up of 14SWG / 16SWG / 18 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt seaman's grey texture finish with following specifications.• Main Contactor of 9A 240V 4 pole contactor with 04 -06A............................................................................Spring return selector switch for each hoist with UP & DOWN indication.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 132 | SplitterSupply and installation of Splitter RDM Compatible DMX Splitter unit with Minimum following specifications.•1 Nos 5 Pin DMX In socket and 8 Nos S Pin DMX Out socket•ln and out signal Optically Isolated•LED Indicator for check the signal flow in output.•Suitable for standard 19” cabinet•Duly black epoxy polyester powder coated texture finish.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 133 | Console Supply and installation of Digital Lighting Console with Ultimate portability, ofieringa powedut LEDand movngight controller in a small 19” unit with direct access to each of the lights.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 134 | XLR Male / Female ConnectorsSupply and installation of 5 pin XLR male / female connectors of made up of Extra high temperature resistant insulator material, Larger solder contacts for easier termination. |
| 135 | XLR Termination PlugSupply and installation of MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX Male socket, junction box made up of 22SWG CRCA, with Pipe clamp on pipe grid arrangement |
| 136 | Power CableSupply and installation of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to lS694 size 3cx1.5 sq mm. (Polycab / KEI) |
| 137 | DMX Signal CableSupply and installation of DMX Signal 2 OR 4 core + Ground shielding Cable with CE mark for the Signal network. (Deepcab / Falcon / Belden) |
| 138 | Motor Power CableSupply and installation of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to lS694 size 4cx 4 sq mm |
| 139 | Motor Control CableSupply and installation of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 7cx1.5 sq mm. |
| 140 | Cable RacewaysSupply and installation of MS perforated tray of Size 40 x 75 x 40mm & 1.6 mm Thickness. |
| 141 | Internal Earthing Supply and installation of Internal earthing copper bare conductor of size 14 SWG for power network related to work coming under scope. |
| 142 | Installation hardwaresSupply and installation of Installation hardware's such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work. |
| 143 | CRAFTING:Main Valance Bar Supply and installation of Main Valance Bar, length 12 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders. (Make:- Leksa/ Markrich/ Aultra Lighting) |
| 144 | Motorised Austrian Main Curtain Supply and installation of Verticle Movement Austrian Main Curtain Mechanism Size - 12 Mtr Length x 10 Mtr Height as directed by Department .(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 145 | Motorised Rear CurtainSupply and installation of Rear Curtain track system 12 Mtrs long, center parting with overlap of 0.9mtr arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish.(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 146 | FRILL Bar Supply and installation of Frill Bar, length 8.5 Mtrs made using 40NB, 48mm OD construction arrangement 2mm Thickness undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with suitable suspenders .(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 147 | Wing Frame Supply and installation of MS, Wing frame made out of 25X25mm or higher size made of MS square pipe with 2mm in thickness (10 Mtr)(Make:- Leksa/ Markrich/ Aultra Lighting) |
| 148 | Motor Cable Termination Box Supply and installation of Motor Cable Termination box for power cable termination at grid level. |
| 149 | Motor Control Center Panel Supply and installation of MS Fabricated Combined Motor Control Center panel cum Remote Control panel for Curtain system made up of 14SWG / 16SWG / 18 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt seaman's grey texture finish with following specifications.• 16A TP or TPN Incomer....................Panel Including wiring with proper earthing |
| 150 | Main Valance FabricSupply and installation of Main Valance Fabric : Fire retardant velvette fabric 100% (2 times of the finished dimension) gathering as per the approved patern and colour, not less than 300 GSM, duly stitched along with eyelets. Size : 12 x 1.3 Meter |
| 151 | Main Curtain FabricSupply and installation of Main Curtain Fabric : Fire retardant velvette fabric with lining 250% (3.5 times of the finished dimension) gathering as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets.Size : 13 x 10 Meter |
| 152 | Rear Curtain FabricSupply and installation of Rear Curtain Fabric : Fire retardant cotton fabric 50% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 13 x 10 Meter |
| 153 | Frill FabricSupply and installation of Frill Fabric : Fire retardant cotton and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 8.5 x 1.3 Mtr |
| 154 | Wing FabricSupply and installation of Wing Fabric : Fire retardant cotton fabric 0% gathering for as per the approved patern and colour, not less than 250 GSM, duly stitched along with eyelets. Size : 10 x 1.5 Mtr |
| 155 | Cyclorama ScreenSupply and installation of Cyclorama : Perforated plastic Cyclorama screen with zero gain, off white, with eyelets along all four sides, perforated plastic screen with eyelets. Size : 11.5 x 5.5 Meter. |
| 156 | Motor Power CableSupply and installation of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to lS694 size 4cx 4 sq mm |
| 157 | Motor Control CableSupply and installation of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 7cx1.5 sq mm. |
| 158 | Supply and Installation of LED Profile Cove lighting & LED Strip (Color Temperature:- 3000K & 4000K), Profile Size: Height:- 6MM, Width:- 17MM including LED Driver having power 5W - 10W (Make:-Phillips/ Syska) |
| 159 | AUDIO-VIDEO SYSTEM:FOH Array Speaker to Be Fixed On Existing Array FrameSupply, Installation, Testing and Commissoning of 12 in. Two-Way Line Array Loudspeaker System. Power Rating 800 W / 1600 W / 3200 W, Frequency Range (-10dB):- 57 Hz - 20 kHz, Frequency Response (±3 dB):- 75 Hz - 20 Hz, Coverage Pattern:- 100 x 15 nominal, Crossover Modes:- Bi-amp / passive, externally switchable, Crossover Frequency:- 132 dB SPL peak 1.2 kHz, Maximum SPL (1m):- 130 dB SPL peak (passive mode), LF: 130 dB HF: 139 dB, Sensitivity Passive: 95 dB SPL Bi-amp LF: 95 dB SPL Bi-amp HF: 114 dB SPL(Make:- JBL/ Renkus Heinz/ Funktion One) |
| 160 | Stage Side Fills Speakers (Top + Subwoofer)Supply, Installation, Testing and Commissioning of 12\\" Two-Way Loudspeakers. Frequency Range (-10dB):- 50 Hz – 20 kHz, Frequency Response (±3 dB):- 62 Hz – 19 kHz, Coverage Pattern:- 90° x 50° nominal, System Sensitivity:- 95 dB SPL (1w@1m), Power Rating, Pink Noise:- 300 W / 600 W / 1200 W(Continuous/Program/Peak), Maximum SPL (1m):- 126 dB SPL peak, Nominal Impedance:- 8 ohms.(Make:- JBL/ TRenkus Heinz/ Funktion One) |
| 161 | Supply, Installation, Testing and Commissioning of Two-channel, 500W Power Amplifier. Channels:- 2, Sensitivity:- 1.4V, Rated Power Output (per channel):- 700W 2Ω, 500W 4Ω, 275W 8Ω, Signal to Noise Ratio (below rated 1 kHz power at 8 ohms):- 100 dB (A-weighted), THD:- < 0.5%, Frequency Response (at 1W, 20 Hz - 20 kHz):- + 0 dB, -1 dB, Crosstalk (below rated power) 20 Hz to 1 kHz:- >70 dB.(Make:- Crown/ Powersoft/ Procella) |
| 162 | Supply, Installation, Testing and Commissioning of 18 in. High Power Subwoofer. Frequency Range:- 35 Hz – 250 Hz, Frequency Response:- 52 Hz – 120 Hz, System Sensitivity:- 95 dB SPL (1w@1m), Power Rating, Pink Noise:- 800 W / 1600 W / 3200 W (Continuous/Program/ Peak), Maximum SPL (1m):- 130 dB SPL peak, Nominal Impedance:- 8 ohms.(Make:- Turbosound/ Tannoy/ JBL) |
| 163 | Supply, Installation, Testing and Commissioning of Amplifier. Channels 2; Sensitivity 1.4V; Rated Power Output (per channel) 3000W 2Ω, 2100W 4Ω, 1200W 8Ω; Signal to Noise Ratio (below rated 1 kHz power at 8 ohms) 103 dB (A-weighted); THD < 0.5%; Frequency Response (at 1W, 20 Hz - 20 kHz) + 0 dB, -1 dB; Crosstalk (below rated power) 20 Hz to 1 kHz >70 dB (Make:- Labgruppen/ Powersoft/ Crown) |
| 164 | Ground Stack Main SubwoofersSupply, Installation, Testing and Commissioning of 18 in. High Power Subwoofer. Frequency Range:- 35 Hz – 250 Hz, Frequency Response:- 52 Hz – 120 Hz, System Sensitivity:- 95 dB SPL (1w@1m), Power Rating, Pink Noise:- 800 W / 1600 W / 3200 W (Continuous/Program/ Peak), Maximum SPL (1m):- 130 dB SPL peak, Nominal Impedance:- 8 ohms.(Make:- Turbosound/ Tannoy/ JBL) |
| 165 | Supply, Installation, Testing and Commissioning of Amplifier. Channels 2; Sensitivity 1.4V; Rated Power Output (per channel) 3000W 2Ω, 2100W 4Ω, 1200W 8Ω; Signal to Noise Ratio (below rated 1 kHz power at 8 ohms) 103 dB (A-weighted); THD < 0.5%; Frequency Response (at 1W, 20 Hz - 20 kHz) + 0 dB, -1 dB; Crosstalk (below rated power) 20 Hz to 1 kHz >70 dB .(Make:- Labgruppen/ Powersoft/ Crown) |
| 166 | Front Fill/ Delay SpeakersSupply, Installation, Testing and Commissioning of High Power Loudspeakers. Frequency Range 37 Hz –18 kHz (-10 dB), Power Capacity 300 W Continuous Program Power; 150 W Continuous Pink Noise, Transformer Taps 70 V: 110 W, 55 W, 28 W & 14 W 100 V: 110 W, 55 W, & 28 W, Thru Position: 8 ohms nominal, Frequency Response 45 Hz – 18 kHz ( ± 3 dB), Maximum SPL (1m) Short-Term: 120 dB; Long-Term: 114 dB, Nominal Sensitivity 90 dB (2.83V / 1m), Coverage Angle 110°H x 85°V, Rotatable |
| 167 | Supply, Installation, Testing and Commissioning of Two-channel, 650W @ 4Ω Power Amplifier. Sensitivity 1.4Vrms, Frequency Response +0dB, -1dB, Signal to Noise >103dB (at .775Vrms, 6dB lower), Intermodulation Distortion < 0.3%, Damping Factor > 200, THD < 0.5% |
| 168 | Audio Mixing ConsoleSupply, Installation, Testing and Commissioning of 40-Input, 25-Bus Digital Mixing Console with 32 Programmable MIDAS Preamps, 25 Motorized Faders, Channel LCD’s, 32-Channel Audio Interface and iPad/iPhone Remote Control. (Make:- Behringer/ Soundcraft/ Yamaha) |
| 169 | Supply, Installation, Testing and Commissioning of I/O Box with 32 Remote-Controllable Midas Preamps, 16 Outputs and AES50 Networking.(Make:- Behringer/ Soundcraft/ Yamaha) |
| 170 | Digital Sound ProcessorSupply, Installation, Testing and Commissioning of DSP core with 16 user-configured card slots, Lua scripting engine, optional software-licensed HearClear AEC. THD+N (22Hz to 22kHz):- 0.002% (1kHz @ +4dBu), EIN:- <125dBu, unweighted (20Hz to 20kHz), Dynamic Range:- 110dB, unweighted, Propagation Delay:- 4ms, Crosstalk, input to input, 1kHz :- <110dB, Sampling Rate:- 48kHz, A/D-D/A Converters:- 32-bit, Card Slots:- 16 user-configurable, Display(s):- Single OLED display at front of device, Controls, Service & Indicators:- Up/Select/Down buttons. Recessed IP reset. Factory service micro-USB. (Make:- Xilica/ Symetrix/ Biamp) |
| 171 | Supply, Installation, Testing and Commissioning of Touch Control Panel(Make:- Xilica/ Symetrix/ Biamp) |
| 172 | MicrophonesSupply, Installation, Testing and Commissioning of Gooseneck Microphone. Audio frequency bandwidth20 - 20000 Hz; Recommended load impedance2000 Ohms; Voltage9 to 52 V; Current3.5 mA. It is inclusooseneck Capsule and Base with on/off switch(Make:- Audio Technica/ Sennheiser/ AKG) |
| 173 | Supply, Installation, Testing and Commissioning of Wireless Vocal Hand Held Microphone Set With Dynamic Cardioid Microphone Capsule; Enhanced Frequency Bank System With Up To 12 Compatible Frequencies; Frequency Response 80Hz - 180KHz; AF Sensitivity 2,5 mV/Pa.(Make:- Audio Technica/ Sennheiser/ AKG) |
| 174 | Supply, Installation, Testing and Commissioning of Wireless Lapel Microphone Set With Dynamic Cardioid Microphone Capsule; Enhanced Frequency Bank System With Up To 12 Compatible Frequencies; Frequency Response 80Hz - 180KHz; AF Sensitivity 2,5 mV/Pa.(Make:- Audio Technica/ Sennheiser/ AKG) |
| 175 | Supply, Installation, Testing and Commissioning of Wired,Dynamic Super-cardioid Microphone For Speech And Vocals With Noiseless On/Off Switch.(Make:- Audio Technica/ Sennheiser/ AKG) |
| 176 | Supply, Installation, Testing and Commissioning of Wired Dynamic Instrumental Microphone(Make:- Audio Technica/ Sennheiser/ AKG) |
| 177 | Supply, Installation, Testing and Commissioning of Drum Kit (01 x Bass Drum Mic, 04 x Tom Mics, 01 x Snare Mic, 02 x Overhead Mics along with Case), Pickup pattern:- Supercardioid, Cardioid, Transducer type:- Condenser, Dynamic, Connection:- Wired, Connectors:- 3-pin XLR (Make:- Sennheiser/ Shure/ Audio Technica) |
| 178 | Supply, Installation, Testing and Commissioning of Boundary Condenser Microphone. Pickup pattern:- Half cardioid, Transducer type:- Condenser, Connection:- Wired, Connectors:- 3-pin XLR.(Make:- Sennheiser/ Shure/ Audio Technica) |
| 179 | Supply and Installation of Microphone Stand(Make:- Hercules/ Softline) |
| 180 | Supply, Installation, Testing and Commissioning of 8-12 Ch Rack Mountable Audio Mixer. Premium 8 ormore-Input 2-Bus Mixer with Mic Preamps and British EqsInput Channels: 8Inputs (Mic Preamps): 4 x XLRInputs (line): 4 x 1/4\\" (Mono), 8 x 1/4\\" (Stereo Paired)Inputs (other): 2 x RCA Outputs (main): 2 x 1/4\\" (Main Out), 2 x 1/4\\" (Control Room Out)Outputs (other): 2 x RCA Phantom Power: 4Aux sends: 1 x Post Send/Return i/o: 1 x TRS (FX Send) Faders: 1 x 60mm (Master Fader)Headphones: 1 x1/4\\"Power Consumption: 20W(Make:- Behringer/ Studio Master/ Yamaha) |
| 181 | Supply, Installation, Testing and Commissioning of Gooseneck Microphone. Audio frequency bandwidth20 - 20000 Hz; Recommended load impedance2000 Ohms; Voltage9 to 52 V; Current3.5 mA. It is inclusooseneck Capsule and Base with on/off switch(Make:- Audio Technica/ Sennheiser/ AKG) |
| 182 | Supply, Installation, Testing and Commissioning of Wireless Vocal Hand Held Microphone Set With Dynamic Cardioid Microphone Capsule; Enhanced Frequency Bank System With Up To 12 Compatible Frequencies; Frequency Response 80Hz - 180KHz; AF Sensitivity 2,5 mV/Pa.(Make:- Audio Technica/ Sennheiser/ AKG) |
| 183 | Cables & ConnectorsSITC of 2 core 12 AWG/4 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant(Make:- Belden/ Klotz/ Gotham) |
| 184 | SITC of 2 core 14 AWG/2.5 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant(Make:- Belden/ Klotz/ Gotham) |
| 185 | SITC of 2 core Twisted, shielded balanced Audio and control cable with 22AWG or better 7 strand annealed bare copper conductors, Semi-Rigid PVC insulation, Riser rated PVC jacket. UL 444, UL 13 CMR rated (Make:- Belden/ Klotz/ Gotham) |
| 186 | SITC of Audio Connectors like XLR, RCA, EP, Mono etc.(Make:- Amphenol/ Gotham/ Neutrik) |
| 187 | SITC of 17U Floor Mounted Equipment Rack (Make: Valrack/ Netrack/ DLink) |
| 188 | UPS SystemSupply, Installation, Testing and Commissioning of 10KVA -10KW 3ph/3ph Online UPS with MS Rack, Interlink Cables, 15M Cable, DC Breaker with Enclosure(Make:- Numeric/ Vertive/ ABB) |
| 189 | Projection SystemSupplying installation, testing, programming and commissioning of Video equipment HDMI HDBaseT Extender (4K@100m) (HDBaseT Class A): Video Input Interfaces 1 x HDMI Type A Female (Black), Max. Distance 1.8 m, Video Output Interfaces 1 x HDMI Type A Female (Black), Video Max. Data Rate 10.2 Gbps (3.4 Gbps Per Lane) 10.2 Gbps (3.4 Gbps Per Lane), Max. Pixel Clock Up to 340 MHz Up to 340 MHz, Compliance HDMI (3D, Deep Color, 4K) HDCP Compatible, Max. Resolutions / Distance Up to 4K@70m (Cat 5e/6) / 100m (Cat 6a), 1080p@100m, 4K supported: 4096 x 2160 / 3840 x 2160 @ 60Hz (4:2:0), 4096 x 2160 / 3840 x 2160 @ 30Hz (4:4:4)(Make:- Purelink/ Extron/ LibertyAV) |
| 190 | Supply, Installation, Testing and Commissioning of 10000 Lumens 3 LCD Laser Projector. Size of effective display area:- 1” x 3 BrightEra LCD Panel, Aspect ratio: 16:10, Number of pixels:- 6,912,000 (1920 x 1200 x 3) pixels, Aspect ratio:- 16:10, Resolution:- WUXGA (1920 x 1200 pixels)(Make:- Sony/ Christie/ Barco) |
| 191 | Supply, Installation, Testing and Commissioning of Lens for the Above Projector.(Make:- Sony/ Christie/ Barco) |
| 192 | Supply, Installation, Testing and Commissioning of 98\\" 4K UHD Interactive Display. Resolution:- 3840 × 2160 (4K UHD) Max visual area:- 2158.85(W)×1214.35(H) mm Screen assembly process:- Zero Bonding Technology, Backlight Type:- DLED, Display Type:- Interactive Flat Panel , Pixel pitch :- 0.5622 ×0.5622, Screen Ratio:- 16:9 Brightness:- Up to 450 cd/m² (nits). It includes Core i5 OPS Kit.(Make:- Peoplelink/ Barco/ Christie) |
| 193 | Supply, Installation, Testing and Commissioning of 4500 Lumens Projector. Projection System: 0.65\\" WXGA, Native Resolution: 1280x800, Brightness: 4500 (ANSI Lumens), Contrast Ratio with SuperEco Mode: 12500:1, Display Color: 1.07 Billion Colors, Light Source Type: 240W UHP Lamp, Light Source Life (hours) with, Normal Mode: 4000, Light Source Life (hours) with SuperEco Mode: 12000, Lens: F=2.41-2.53, f=21.85-24mm, Projection Offset: 124.8%+/-10%, Throw Ratio: 1.544-1.72, Optical Zoom: 1.1x, Digital Zoom: 0.8x-2.0x, Image Size: 30\\"-300\\", Throw Distance: 1.00-11.11m(Make:- Viewsonic/ Panasonic/ Christie) |
| 194 | Supply, Installation, Testing and Commissioning of 8 Feet X 6 Feet Motorized Projection Screen (Make:- Liberty/ Milan/ Suvira) |
| 195 | Supply, Installation, Testing and Commissioning of Projector Ceiling Mount(Make:- Liberty/ Milan/ Suvira) |
| 196 | Supply, Installation, Testing and Commissioning of Constant Beamwidth Technology™ Line Array Column Loudspeaker. Drivers Eight 50 mm(2 in) Full-Range Frequency Range (-10dB) 80 Hz – 20 kHz Coverage Angle Vertical 20° (1.5 kHz - 16 kHz, ±10°) Horizontal 150° (ave, 1 kHz – 4 kHz, ±20°) Sensitivity 93 dB (speech mode, 2 kHz - 14 kHz)89 dB (music mode, 300 Hz - 18 kHz) Impedance 8 ohms.(Make:- JBL/ Audac/ Atlas IED) |
| 197 | Supply, Installation, Testing and Commissioning of Two-channel, 525W @ 4Ω Power Amplifier. Frequency Response +0dB, -1dB, Signal to Noise >103dB (at .775Vrms, 6dB lower), Intermodulation Distortion < 0.3%, Damping Factor > 200, THD < 0.5%, Crosstalk At 1kHz: > 85dB, At 20kHz: > 55dB |
| 198 | SITC of 2 core 14 AWG/2.5 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant(Make:- Belden/ Klotz/ Gotham) |
| 199 | SITC of 2 core Twisted, shielded balanced Audio and control cable with 22AWG or better 7 strand annealed bare copper conductors, Semi-Rigid PVC insulation, Riser rated PVC jacket. UL 444, UL 13 CMR rated (Make:- Belden/ Klotz/ Gotham) |
| 200 | SITC of Audio Connectors like XLR, RCA, EP, Mono etc.(Make:- Amphenol/ Gotham/ Neutrik) |
| 201 | WATER SUPPLY & SANITARY INSTALLATION WORK Sub Head – I Sanitary InstallationProviding and fixing Wall mounted, white vitreous china water closet of approved brand/make, shape, size and pattern including concealed cistern of capacity (3/6 ) litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, W.C bolts Fastener and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. Make- Euronics - / Jaquar/Kohlar |
| 202 | Providing and fixing white vitreous china battery / Electric based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. |
| 203 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 204 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 205 | Providing and fixing white vitreous china wash basin under counter / Table Top basin, with C.I. concealed type brackets fixed to walls with GI rag bolts or approved fasteners etc., including 32 mm CP brass waste coupling, including painting of fittings and brackets, cutting and making good the walls wherever required all complete (Granite counter top will be measured and paid separately under relevent item): as per approved make and decision of engineer-in-charge . Make Jaquar Cat No-LYS-WHT-38931 / Equivalent |
| 206 | Providing and fixing toilet paper holder :C.P. brass |
| 207 | Providing and fixing CP brass auto closing system basin pillar tap / hand wash as approved by Engineer- In Charge |
| 208 | Providing and fixing 32mm C.P brass bottle Trap of approved quality & make as per the direction of engineer-in-incharge. |
| 209 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 210 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board610x460 mm bowl depth 200 mm |
| 211 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe40 mm dia |
| 212 | Providing and fixing soil, waste and vent pipes :100 mm diaHubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 |
| 213 | Providing and fixing soil, waste and vent pipes :75 mm diaHubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 |
| 214 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mmHubless centrifugally cast (spun) iron epoxy coated inside & outside I.S. 15905 |
| 215 | Providing and fixing plain bend of required degree.100 mmHubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 |
| 216 | Providing and fixing plain bend of required degree.75 mmHubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 |
| 217 | Providing and fixing heel rest sanitary bend100 mm diaSand cast iron S&S as per IS - 3989 |
| 218 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100x100x100 mmsand cast Iron S&S as per IS: 3989 |
| 219 | Providing and fixing single equal plain junction of required degree 100x100x100 mm Hubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 |
| 220 | Providing and fixing single equal plain junction of required degree 75x75x75 mmHubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 |
| 221 | Providing and fixing single equal plain junction of required degree 100x100x75 mmHubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 |
| 222 | Providing and fixing terminal guard: 100 mmHubless centrifugally cast (spun) iron pipe epoxy inside & outside IS: 15905 |
| 223 | Providing and fixing terminal guard: 75 mmSand cast iron S&S as per IS - 3989 |
| 224 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipes100 mmS S 304 grade coupling with EPDM rubber gasket |
| 225 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipes75 mmS S 304 grade coupling with EPDM rubber gasket |
| 226 | Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter :100 mm |
| 227 | Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter :75 mm |
| 228 | Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 100 mm diameter pipe |
| 229 | Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 75 mm diameter pipe |
| 230 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. :100 mm diameter pipe |
| 231 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. :75 mm diameter pipe |
| 232 | Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.32 mm dia. nominal bore |
| 233 | Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.40 mm dia. nominal bore |
| 234 | Providing and fixing G.I. soil / waste pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.50 mm dia. nominal bore |
| 235 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outletHubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 236 | Providing & fixing in position GI 100x50 elbow floor drain including cost of cutting and making good the walls and floors wherever required. |
| 237 | Providing and fixing 125 mm dia S/S grating (with or without hole)for floor or Nahani trap. |
| 238 | Providing and fixing Soap Dispenser with Glass Bottle with fittings of approved quality with all complete. ( Make Jaquar - ACN-1135N / Equivalent ) |
| 239 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 240 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.110 mm diameter |
| 241 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler110 mm |
| 242 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee with door110x110x110 mm |
| 243 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Bend 87.5°110 mm |
| 244 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Shoe (Plain)110 mm Shoe |
| 245 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm |
| 246 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 247 | Providing & Fixing water cooler wth stainless steel having storage capacity of 80 liter & cooling capacity 60 liter / hour with Reverse osmosis system & ultra voilet membrane TDS reduction 90% having automatic back wash system with filteration unit & all other required accessories complete in all respect as per direction of the engineer in charge . |
| 248 | Providing & fixing 692 mm long stanless steel Grab bar fixed from wall face with concealed fittings arrangement of approved quality with all complete. Make - Jaquar -WAC-SAP-BR0600CSN / Equivalent |
| 249 | Providing & fixing stanless steel Grab Bar Vertical Swing from wall face with concealed fittings arrangement of approved quality with all complete. Make - Jaquar - WAC-WHT-BG0800N / Equivalent |
| 250 | Providing and fixing urinal partition of size 90x320x720 mm deep. including cutting and making good the wall wherever required. |
| 251 | Providing, fixing, testing and commissioning pressurized electric water heater with copper sheet container with suitable length of electrical cable and 15 amp 3 pin plug top, complete in all respect.15 Ltr. |
| 252 | Sub Head – II Water Supply:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work – Exposed on wall.20 mm nominal outer dia Pipes |
| 253 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work – Exposed on wall.25 mm nominal outer dia Pipes |
| 254 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work – Exposed on wall.32 mm nominal outer dia Pipes |
| 255 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work – Exposed on wall.40 mm nominal outer dia Pipes |
| 256 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work – Exposed on wall.50 mm nominal outer dia Pipes |
| 257 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed including cutting chases and making good the wall etc.15 mm nominal outer dia Pipes |
| 258 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed including cutting chases and making good the wall etc.20 mm nominal outer dia Pipes |
| 259 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed including cutting chases and making good the wall etc.25 mm nominal outer dia Pipes |
| 260 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work100 mm nominal dia Pipes |
| 261 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm dia. nominal bore |
| 262 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm dia. nominal bore |
| 263 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm dia. nominal bore |
| 264 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm dia. nominal bore |
| 265 | Providing and fixing hand held ablution fitting (health faucet) with 1.2 meter long flexible tube and wall hook, all complete approved engineer-in-charge |
| 266 | Supply and fixing of 15mm CP brass 2 -Way Bib Cock with wall flange and suitable length CP brass extension pipe all of approved engineer-in-charge |
| 267 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 268 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore |
| 269 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore |
| 270 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length15 mm nominal bore |
| 271 | Supply ,Erection , Testing & Commissioning of Automatic water level control panel & related accessories for pumping automation with consisting of automatic water level controller , level sensor with stainless steel probe, motorized butterfly valve, motorized valve controller with complete in all respect.upto 50 mm dia. nominal bore |
| 272 | Providing and fixing Air realease valve r of quality & make as approved by Engineer in charge.upto 50 mm dia. nominal bore |
| 273 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 274 | Sub Head – III Drainage:Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kinds of soilPipes, cables etc. exceeding 80 mm dia. but notexceeding 300 mm dia |
| 275 | Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098 ( Part - 2 ) 3013 for soil / waste pipe under ground drainage system with jointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. 150 mm diameter |
| 276 | Supply and fixing HDPE double wall corrugated ( DWC ) I.S 16098 ( Part - 2 ) 3013 for soil / waste pipe under ground drainage system with jointed with rubber ring with good quality lubricant for fittings, inclusive of all necessary specials like bends, tees, offsets, junctions, re excavtion and refillig etc complete. 200 mm diameter |
| 277 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :150 mm diameter |
| 278 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :200 mm diameter |
| 279 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not lessthan 4.50 kg and frame to be not less than 2.70 kg as per standard design :180x150 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 280 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe |
| 281 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :250 mm dia. R.C.C. pipe |
| 282 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) with RCC top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size ) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size ) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation cocreate 1:3:6 mix (1 cement :3 coarse sand : 6 graded stone aggregate 40 mm norminal size),and making necessary channel in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm norminal size) finished with a floating coat of neat cement complete as per standard design .inside size 90x80 cms and 45 cms deep including CI cover with frame ( light duty ) 455x610 mm internal dimensions total weight of cover & frame to be not less than 38 kg (weight of cover 23 kg & weight of frame 15 kg )with common brunt clay FPS ( non modular ) bricks of class designation 7.5 |
| 283 | Extra depth for manhole 90x80 cmWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 284 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS:1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering esides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per pecifications and having manufacture’s permanent identification mark to be visible even after fixing,including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 285 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 286 | FIRE FIGHTING WORKS:Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor)25 mm dia |
| 287 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor)32 mm dia |
| 288 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor)40 mm dia |
| 289 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor)50 mm dia |
| 290 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor)65 mm dia |
| 291 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor)80 mm dia |
| 292 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor)100 mm dia |
| 293 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :100mm dia |
| 294 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Pendent Sprinkler |
| 295 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Upright Sprinkler |
| 296 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Horizontal side wall sprinkler |
| 297 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Concealed sprinkler |
| 298 | Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.100mm dia |
| 299 | Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 700 mm |
| 300 | Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.1000 mm |
| 301 | Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.1200 mm |
| 302 | Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.1500 mm |
| 303 | Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required. |
| 304 | Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required |
| 305 | Providing and fixing 25 mm dia inspection & testing assembly with gun metal ball valve, gun metal sight glass ,Reducer ,union, G.I PIPE. connection to drain pipe/riser. |
| 306 | INTERNAL ELECTRIFICATION & POWER WIRING SUB HEAD - I - CIRCUIT CUM POINT WIRINGSWITCH CONTROL LIGHT POINTSWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C |
| 307 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. Group C |
| 308 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C |
| 309 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. |
| 310 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 311 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 312 | Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 313 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.CIRCUIT -SUBMAIN WIRING2x1.5 sq mm + 1x1.5 sq mm earth wire |
| 314 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.CIRCUIT -SUBMAIN WIRING2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 315 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.CIRCUIT -SUBMAIN WIRING4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire |
| 316 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.CIRCUIT -SUBMAIN WIRING2x6 sq mm + 1x6 sq mm earth wire. |
| 317 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.CIRCUIT -SUBMAIN WIRING4x10 sq mm + 1x6sq mm earth wire. |
| 318 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.CIRCUIT -SUBMAIN WIRING4x16 sq mm + 2x6sq mm earth wire. |
| 319 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 320 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 10 sq. mm + 1 x 6 sq.mm earth wire |
| 321 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 16 sq. mm + 2 X 6 sq. mm earth wire |
| 322 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 323 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). |
| 324 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 325 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 326 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 327 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75mmX75mm) |
| 328 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.6 module (200mm X 75 mm) |
| 329 | Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A \\"C\\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 330 | Supplying and fixing of following sizes of STEEL conduit alonwith the accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.20mm dia |
| 331 | Supplying and fixing of following sizes of STEEL conduit alonwith the accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.25mm dia |
| 332 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 333 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm |
| 334 | SUBHEAD - II - DISTRIBUTION BOARDS:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).12 way, Double door |
| 335 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).6 Way (4+18), Double Door |
| 336 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).8 Way (4+24), Double Door |
| 337 | Supplying and fixing of following ways surface/recess mounting, vertical type, 415V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlet are required.)12 way (4 + 36), Double door |
| 338 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole |
| 339 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 A |
| 340 | Supplying and fixing of following rating four pole (Three phase and neutral) 415 volts, Residual Current Breaker with Overload (RCBO), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required.40 A |
| 341 | Supplying and fixing of following rating four pole (Three phase and neutral) 415 volts, Residual Current Breaker with Overload (RCBO), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required.63 A |
| 342 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 343 | SUB HEAD - III - SUPPLY & FIXING OF INTERNAL LIGHT FIXTURES Supply, Installation, Testing and Commissioning of 18W Surface/Recessed Mounted LED circular Downlighter. |
| 344 | Supply, Installation, Testing and Commissioning of 18/20W Wall/Surface mouted 4 ft. LED |
| 345 | Supply, Installation, Testing and Commissioning of 36W (Nominal) 2x2 ft Recess Mounted LED Luminaire. |
| 346 | Supply, Installation, Testing and Commissioning of 12/15W Recessed mounted LED circular Downlighter. |
| 347 | SUPPLY & FIXING OF INTERNAL LIGHT FIXTURES 40W DALI dimmable LED DownlightSupply, Installation, Testing & Commissioning of DALI dimmable 40W COB LED Gimball adjustable Downlight luminaire shall provide 4000 lumens with a cut-out diameter of 154mm and a height of 82mm, suitable for recess mounting. Downlighter made of Aluminium die cast powder coated housing with an inbuilt heat sink for enhanced thermal management, ensuring long LED life. The optical compartment will include a high-efficiency reflector and a PC diffuser to produce a precise light beam while minimizing glare, achieving a Unified Glare Rating (UGR) of less than 15. The luminaire will be equipped with LM 80-08 compliant LEDs from reputed manufacturers like Nichia, Cree, Bridgelux, Lumileds, Osram, Seoul, or Citizen, with a minimum L70 life of 50,000 hours, supported by a complete LM 80 test report for 10,000 hours. Additionally, the LEDs will comply with EN 62471 for photobiological safety, and a certificate confirming compliance will be provided. The color temperature will be 4000K, with a minimum Color Rendering Index (CRI) of 80, and the available beam angles will be 36°. The luminaire will feature an integrated, isolated, constant current operated DALI 2.0 certified LED driver with a voltage range of 120-270V AC. The driver will have an efficiency greater than 85%, 3 kV internal surge protection, a power factor greater than 0.95, and total harmonic distortion (THD) of less than 10% @Full load. The luminaire will be IP20 rated for indoor use. LM 79 and LM 80 reports from a NABL/UL accredited lab will be provided to verify the performance. The product will comply with Indian standards IS 10322 Part 5/Sect 2, IS 16105:2012, IS 16106:2012, IS 15885 (Part 2/Sec 13):2012, and IS 16108:2012. The manufacturer must also have an in-house lab approved by NABL or the Ministry of Science and Technology, Government of India. As per DBR specification. |
| 348 | 32W DALI dimmable LED DownlightSupply, Installation, Testing & Commissioning of DALI dimmable 32W COB LED Gimball adjustable Downlight luminaire shall provide 3200 lumens with a cut-out diameter of 132mm and a height of 82mm, suitable for recess mounting. Downlighter made of Aluminium die cast powder coated housing with an inbuilt heat sink for enhanced thermal management, ensuring long LED life. The optical compartment will include a high-efficiency reflector and a PC diffuser to produce a precise light beam while minimizing glare, achieving a Unified Glare Rating (UGR) of less than 15. The luminaire will be equipped with LM 80-08 compliant LEDs from reputed manufacturers like Nichia, Cree, Bridgelux, Lumileds, Osram, Seoul, or Citizen, with a minimum L70 life of 50,000 hours, supported by a complete LM 80 test report for 10,000 hours. Additionally, the LEDs will comply with EN 62471 for photobiological safety, and a certificate confirming compliance will be provided. The color temperature will be 4000K, with a minimum Color Rendering Index (CRI) of 80, and the available beam angles will be 60°. The luminaire will feature an integrated, isolated, constant current operated DALI 2.0 certified LED driver with a voltage range of 120-270V AC. The driver will have an efficiency greater than 85%, 3 kV internal surge protection, a power factor greater than 0.95, and total harmonic distortion (THD) of less than 15% @Full load. The luminaire will be IP20 rated for indoor use. LM 79 and LM 80 reports from a NABL/UL accredited lab will be provided to verify the performance. The product will comply with Indian standards IS 10322 Part 5/Sect 2, IS 16105:2012, IS 16106:2012, IS 15885 (Part 2/Sec 13):2012, and IS 16108:2012. The manufacturer must also have an in-house lab approved by NABL or the Ministry of Science and Technology, Government of India. As per DBR specification. |
| 349 | 6W Step light LED Supply, Installation, Testing & Commissioning of Specially designed step light LED made of aluminium die-cast with PS diffuser, CCT 3000K, 220-240Vac CRI > 80 Input power: 6W. Electronic driver ON/OFF CE mark. IP rating IP65, L70: 30,000hrs. Operating ambient temperature range is from 0°C to +45°C. Warranty: 2years.As per DBR specification. |
| 350 | 16W LED BATTENSupply, Installation, Testing & Commissioning of 16 Watt 4 feet Surface / Suspended / Wall Mounted IP40 LED Batten with minimum luminaire system efficacy of 135 lm/w and lumen output of 2200lm having a color temperature of 5700K and housing should made up of Aluminium Anodized Extruded with high efficiency Polycarbonate diffuser with intergrated isolated constant current driver, LEDs used are SMD, Life of LED 50000 burning Hrs. @L70 Lumen maintenance, CCT 5700K, CRI≥80, PF≥0.95 & THD<10%, an operating Voltage Range of 150 - 270 VAC. Minimum Internal Surge Protection 3KV. The fixture design should comply driver leakage current as per as per IEC 60598 along with BIS certification for LED Driver & Luminaire. Luminaire manufacture shall provide LM79 report from NABL accredited lab. Dimension: 1185 X 40 X 45mm, Weight: 0.55Kg. As per DBR specification. |
| 351 | Supply, Installation, Testing & Commissioning , Installation, Testing & Commissioning of Exit Signages (2 hour battery backup) including all fixing arrangement complete as required. |
| 352 | LIGHTING MANAGEMENT SYSTEMWireless 32 child DALI controller Supply, Installation, Testing & Commissioning of wireless IoT System having BLE 5.2 AES 128 Bit encyption based 32 child DALI controller and analog 2 channel (0-10V) output, operates on 100-277 VAC, 10-30mA, 50Hz, DALI 2.0 protocol. Sensor input of 0-3V DC & 1mA. For analog dimming, It provides output voltage of 0-10V DC +/- 0.2V and 15mA per channel. For DALI output, it provides 12-20V DC and 160mA max for 32 DALI devices. An auxillary power output of 3.3VDC and 30mA. 0 - 100% dimming, device to device range 45m. Controller must control individually control standard DALI or Tunable DALI Drivers independantly or combination of both. Operating temperature -20 to 50 deg celsius, surge protection 3kV. System shall support easy commissioning and configuration via Mobile Application along with user and site management features. Optional Cloud Application must be available for control and monitoring of the devices along with analytics reports. Mobile Application shall have features of individual & group control for On/off/dimming/ colour tuneing / Scene Control / Animation etc. Device must have security key for commissioning and replacement for future.Approved Make: Wipro WCA2CSD32N or equivalent |
| 353 | 5-button wall switch that controls ON/OFFSupply, Installation, Testing & Commissioning of BLE 5.2 AES 128 Bit encyption based wireless battery powered 5-button wall switch that controls ON/OFF, intensity and CCT of an individual or group of luminaires.Operates on 3V DC input voltage in an ambient temperature of 0 to 50 deg celsius and device to device range 45m. System shall support easy commissioning and configuration via Mobile Application along with user and site management features. Optional Cloud Application must be available for control and monitoring of the devices along with analytics reports.Approved Make: Wipro WSC5B or equivalent |
| 354 | Supply, Installation, Testing & Commissioning of WiFi and BLE 5.2 AES 128 Bit encyption Gateway with Ethernet and built-in Real Time Clock for cloud connectivity and scheduling.It is powered by 5V, 2A Mini USB / DC Adaptor and has 1 ethernet port with 10/100 Mbps data transmission rate. RTC is battery powered with 3V DC. Device to device range 30m X 30m, operating ambient temperature of -20 to 55 deg celsius. System shall support easy commissioning and configuration via Mobile Application along with user and site management features. Optional Cloud Application must be available for control and monitoring of the devices along with analytics reports. Device must have security key for commissioning and replacement for future.Approved Make: Wipro WBTWNER or equivalent |
| 355 | Sub Head 'A' - Machinery OUTDOOR UNITSSupplying, Installation,Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc.complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping.The system shall be able to deliver100% of the rated capacity upto 39 °C. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability.The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building) For Cooling or Heating or Both(Considering conversion factor IHP= 0.83TR)44 H.P (12 HP + 12 HP + 20 HP) Cool / Heat Pump Unit |
| 356 | Indoor unit- Ductable TypeSupply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted high ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)High Static Ductable units (minimum 78 pascal external static pressure)8.0 TR |
| 357 | Refent JointsSupply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs.Indoor Units ( In Pair) |
| 358 | Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs.Outdoor Multi Joint |
| 359 | Sub Head-'B'- PipingCOPPER REFRIGERANT PIPINGSupply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. Cable tray is quantified seperately. 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 360 | COPPER REFRIGERANT PIPINGSupply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. Cable tray is quantified seperately. 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 361 | COPPER REFRIGERANT PIPINGSupply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. Cable tray is quantified seperately. 15.9 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 362 | COPPER REFRIGERANT PIPINGSupply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. Cable tray is quantified seperately. 19.1 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 363 | COPPER REFRIGERANT PIPINGSupply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. Cable tray is quantified seperately. 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 364 | COPPER REFRIGERANT PIPINGSupply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. Cable tray is quantified seperately. 28.6 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 365 | COPPER REFRIGERANT PIPINGSupply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. Cable tray is quantified seperately. 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation |
| 366 | COPPER REFRIGERANT PIPINGSupply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work including vaccumiazation and Nitrogen testing suitable for refrigerant R 410A duly insulated with FACTORY PREFORMED TUBULAR EPDM RUBBER FOAM SECTIONS with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000 between indoor & outdoor units as per specifications. External refrigerant piping shall be laid on 16 G GI covered perforated cable trays. Piping inside occupied area & vertical shaft inside the AHU Room shall be supported using 16 G GI hangers. All exposed pipe shall have UV coating on insulation & cost to be included in the piping. Cable tray is quantified seperately. 41.30 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation |
| 367 | Sub Head 'C' - Ducting & Grilles AIR DISTRIBUTION (FOR AIRCONDITIONING)GSS DUCTINGSupply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.0.63 MM (24 gauge) Galvanized Sheet Steel Ducting |
| 368 | AIR DISTRIBUTION (FOR AIRCONDITIONING)GSS DUCTINGSupply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.0.80 MM (22 gauge) Galvanized Sheet Steel Ducting |
| 369 | AIR DISTRIBUTION (FOR AIRCONDITIONING)GSS DUCTINGSupply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.1.0 MM (20 gauge) Galvanized Sheet Steel Ducting |
| 370 | AIR DISTRIBUTION (FOR AIRCONDITIONING)GSS DUCTINGSupply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.18 G, Thickness 1.25 mm sheet (Above 2250 mm) |
| 371 | Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.0.63 MM (24 gauge) Galvanized Sheet Steel Ducting |
| 372 | Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.0.80 MM (22 gauge) Galvanized Sheet Steel Ducting |
| 373 | Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.1.0 MM (20 gauge) Galvanized Sheet Steel Ducting |
| 374 | Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.18 G, Thickness 1.25 mm sheet (Above 2250 mm) |
| 375 | Grilles, Diffusers, VCDSupply and Fixing installation, testing and commissioning of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 376 | Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 377 | Supply and Fixing installation, testing and commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 378 | Supplying, fixing testing commissioning of Return air/ Exhaust diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core. |
| 379 | ACOUSTICSupplying and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminium sheet fixed to inside surface of ducts with cadmium plated nuts,bolts, stick pins, CPRX compound in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 380 | INSULATIONSupplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class“O”) insulation on existing duct after applying Suitable adhesive for nitrile rubber. The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.19 mm thick (In Condition Space) |
| 381 | Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class“O”) insulation on existing duct after applying Suitable adhesive for nitrile rubber. The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.25 mm thick (In Non - Condition Space) |
| 382 | Fire Dampers & ActuatorSupplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Fire Damper |
| 383 | Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Actuator |
| 384 | GSS Duct DamperSupply, installation and testing of multiblade box type Galvanized Sheet Steel construction damper for ducts to be provided with suitable links and quadrants for control of volume of air. |
| 385 | Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU room.Damper |
| 386 | Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU room.Actuator |
| 387 | CONTROL & TRANSMISSION WIRINGSupply,installation,testing and commissioning of 2 Core x 1.5 mm2 copper wire in PVC conduit as per specifications for transmission |
| 388 | Supply, installation, testing and commissioning of 2 Core x 1.5 mm2 copper wire in PVC conduit as per specifications for remotes |
| 389 | REMOTESSupply,installation,testing and commissioning of Corded Remote with necessary wiring till Indoor unit, fittings including all necessary accessories. |
| 390 | Supply,installation,testing and commissioning of Cordless Remote |
| 391 | Inline FansSupplying, installing, testing and commissioning of inline fans suitable for installing in any position in vertical or horizontal ducts. The capacity of the fan given as under. Make: Greenheck/Ostberg/KrugerAir Quantity : 900 CFMStatic Pressure : 20 mm wgMotor rating : As Required |
| 392 | Supplying, installing, testing and commissioning of inline fans suitable for installing in any position in vertical or horizontal ducts. The capacity of the fan given as under. Make: Greenheck/Ostberg/Kruger800 - 1000 CFM (12mm static pressure, single phase) |
| 393 | Supplying, installing, testing and commissioning of inline fans suitable for installing in any position in vertical or horizontal ducts. The capacity of the fan given as under. Make: Greenheck/Ostberg/Kruger1100 - 1500 CFM (12mm static pressure, single phase) |
| 394 | Inline Fans (Kitchen Exhaust)Supply, installation, testing and commissioning of Inline grease exhaust fans of the tubular centrifugal type with backward inclined wheels, built in accordance to NFPA 96, housings made of continuously welded heavy gauge steel with integral duct flanges & suitable for 200 °C temperature. 1500 - 2000 CFM (25mm static pressure, single phase) |
| 395 | Plastic Propeller FansSupplying, installing, testing and commissioning of direct driven PROPELLER FANS. Each fan shall be complete with permanent split capacitor or shaded pole motor, mounting plate with light weight type PVC impellers with aerofoil contours for high efficiency & low noise & gravity louvers for weather protection as required. Fan selection arrangement and Electrical characteristics shall be as follows :Air Quantity : 150 CFMPower : As RequiredDuty : Exhaust |
| 396 | DRAIN PIPINGSupply, installation, testing and commissioning of rigid heavy duty PVC piping complete with fittings, support as per drawing and insulated with 6 mm closed cell elastomeric insulation.25 mm dia |
| 397 | Supply, installation, testing and commissioning of rigid heavy duty PVC piping complete with fittings, support as per drawing and insulated with 6 mm closed cell elastomeric insulation.32 mm dia |
| 398 | Supply, installation, testing and commissioning of rigid heavy duty PVC piping complete with fittings, support as per drawing and insulated with 6 mm closed cell elastomeric insulation.40 mm dia |
| 399 | Supply, installation, testing and commissioning of UPVC condensate drain water piping of density 20 Kg/m³ complete with fittings like elbows, tees, reducers, bends, flanges, supports & duly insulated with \\"O\\" class Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness etc. as required and of following sizes.40 mm dia pipe , 13 mm Insulation |
| 400 | Supply and Installationof 16 G GI Perforated Cable Trays for Copper Pipes and Drain pipes75 x 300 x 75 mm |
| 401 | Supply and Installationof 16 G GI Perforated Cable Trays for Copper Pipes and Drain pipes75 x 150 x 75 mm |
| 402 | Supply, installation and balancing of extruded aluminium powder coated air louvers complete with aluminium wire mesh birdscreen & volume conrtol dampers as per specifications.Fresh air louvers |
| 403 | Supply, installation and balancing of extruded aluminium powder coated air louvers complete with aluminium wire mesh birdscreen & volume conrtol dampers as per specifications.Exhaust air louvers(without volume control dampers) |
| 404 | Expansion Kit, Communication PCB & ThermostatSupply, Installation, Testing & Commissioning of Electronic Type Expansion Kit, Communication PCB with Sensors, Corded Self Diagnostic Type Digital Thermostat, Controller, control box with internal wiring, AHU kit for each DX Type Units and other related accessories etc with connectivity to automation system for A/M status, RUN status & Remote start / stop command (Bacnet/IP). It should be complete as per manufacturing standards & as per directions of Engineer-in-charge. AHU with 44.0 HP VRV ODU |
| 405 | Double Skin Floor Mounted VRV DX AHU (AHRI / Eurovent Certified) with VFDSupply, installation, testing and commissioning of factory fabricated Double Skinned VRV DX Air-handling unit Floor mounted type fabricated out of extruded aluminium section with 0.8 mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside with backward curved plug fan, fan section and fan motor TEFC (IE-3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, VFD with EMC filters C1 Category, 6 Row cooling coil made of Aluminium finned Copper tube with coil section, Coilotron UV section only of 600 mm in length in floor mounted AHU, pre-filter (MERV 8) section with filters of non woven synthetic media of 10 micron particle size with an efficiency of 90%, fine filter (MERV 13) section with filters of non woven synthetic media of 5 micron particle size with an efficiency of 95% in supply after fan, polished stainless steel drain pan made out of 22 G sheet duly insulated.The AHU panels shall be insulated with 50mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. These AHUs shall have air inlet / outlet connection made of 20 G GI sheet. The complete AHU shall conform to specication & face velocity across cooling coil shall be limited to 152 MPM maxm. Static pressure given below is for guideline & actual to be calculated.AHU DX coils shall be in tune with the requirement of VRV Outdoor Unit capacity and no divisions shall be made in cross sectional area of the coil. If multiple ins and outs of refrigerant pipe are required then coils shall be grouped into required rows keeping the cross sectional area of the coil constant. The capacity of Air-handlers shall be as follows: VRF/AHU - 11,000 CFM Capacity, 6 Row CC, 80 mm St. Pr. |
| 406 | Axial Flow Fan Supply, installation, testing and commissioning of ceiling mounted Tube Axial flow fans with adjustable pitch blade, MS / GI long casing (2mm thick up to 800 mm dia fan, 3 mm thick from 900 to 1250 mm dia & 4 mm thick above 1300 mm dia) , cast aluminium alloy impeller complete with TEFC Sq. Cage Induction motor IE-3 suitable for 415 volts ± 10%, 50Hz ± 3 %, three phase A.C supply with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep (Inlet & Outlet as required), bird screen (Inlet & Outlet as required) etc. & of following capacity. The complete fan along with motor shall be high efficient one with fire rated (class H) suitable for withstanding 250 °C temperature rated for 2 hours. Fan outlet velocity shall be limited to maximum of 16 m/sec. Fan & Fan motor KW given below are for guideline & actual Dia / KW shall be as per manufacturer selection based on maximum 16 m/sec outlet velocity. Axial Fan shall be AMCA certified for Air and Sound performance in accordance to AMCA 210 and AMCA 300. Complete Fan shall be tested and approved by CE / UL / EN in accordance with \\"Power Ventilators for Smoke Control Systems\\" for 250 °C for 2 hours. Manufacturer shall furnish AMCA Test Certificate for air & sound performance along with UL / EN fire test certificate (Latest) for each fan sourced from that particular factory. The noise level of axial fan shall be less than 80 dBa at a distance of 3.0 mt from the fan. The fan shall be low RPM (less than or equal to 1000 RPM) and capacities shall be as follows. Wattage of motor shall be as per actual selection meeting other technical parameters33000 CFM (25mm static pressure, Axial Fan, 960 / 1450 RPM, 11.0 Kw Fan Motor or as required, 1120 MM Fan Dia) |
| 407 | AHU Mounted Coilotron UV System For Floor Mounted AHUSupply, installation, testing and commissioning of AHU mountable self contained and factory assembled Coilotron UV System with UL 1995 ABQK listed and UL 2043 certified, UV lamp of 800 mA & life of UV lamp shall not be less than 11000 hours. Coilotron shall be installed in all floor mounted AHUs as specified herein. All the component / parts shall comply with the specification given in the tender. AHU supplier and coilotron supplier shall co-ordinate with each other regarding the fixing of the same in the AHU. For 10,000 to 15,000 CFM AHU |
| 408 | Supplying, fixing testing commissioning of Volume control GI Dampers to be provided in Supply / Exhaust air registers / terminals. |
| 409 | Supplying, fixing testing commissioning of Fresh / Exhaust air louvers with bird screen & damper |
| 410 | Supplying, fixing testing commissioning of Fixed bar linear air register of following sizes150 mm |
| 411 | Supplying, fixing testing commissioning of Fixed bar linear air register of following sizes200 mm |
| 412 | Jet Diffuser - 380 / 400 Dia |
| 413 | Under Deck Insulation of Exposed Roof Supplying and fixing of thermal insulation on exposed roof (underdeck) with 19mm thick EPDM Rubber foam with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000, tape & adhesive (pidilite SR -998) with adhesive (pidilite SR -998) etc. as required & finally fixed with the help of rawl plug & dash fasteners in ceiling. |
| 414 | Electrical Sub Panel Supply, installation, testing and commissioning of cubical floor / wall mounted type switch board as detailed below & switch gears suitable for AC-23 duty with digital energy meter on incoming feeders of all Sub-Panels covered under this Item, including making interconnection etc as required. BMS compitable dual source energy meter with maximum demand shall be taken in main incomer of HVAC Panels.Panel For VRV Outdoor Units & AHU (Panel Suitable For Outdoor Type - IP54) |
| 415 | Supply, installation, testing and commissioning of Cubical type sectinalised floor standing switch board by CPRI apprved firms of 31 MVA fault capacity at 415 V complete with 4 strip, 500 A capacity Aluminium Bus - Bar Electrolytic grade E-91, cable alley, switchgears suitable for AC-23 duty & of following capacity & as per specification given in the tender.a) INCOMER 400 A TPN MCCB with with overload, short ckt., earth fault, protection release, with 144 mm (0 - 400 A) ammeter with 3 CT and selector switch, 144 mm (0 - 500 V) Voltmeter, Energy Meter with RS 485 Port, phase indication light with protection MCB, on / off / trip indicating light with protection MCB. SET 02 b) OUTGOINGSi) For VRV ODU32 / 40 A TPN MCB (12W+4Spare) SET 1ii) For AHU Fan Motor up to 7.5 / 11 Kw VFD Driven & VFD part of AHU40 / 63 A TPN MCB SET 04b) For Fire Damper & Actuator, Coilotron etc. 6 A SP MCB, SET-16Controls & interlocking accessories as required. LOTElectrical Sub Panel For 4 x 15 Kw Fan Motor For Smoke Exhaust / Supply |
| 416 | Supply, installation, testing and commissioning of Cubical type sectinalised floor standing switch board of 15 MVA fault capacity at 415 V complete with 4 strip, 200 A capacity Aluminium Bus - Bar Electrolytic grade, cable alley, switchgears of following capacity & as per specifications. Fire signal shall be provided from fire control panel by seperate agency.i) INCOMER125 A TPN MCCB with (0–125A) ammeter with 3 CT & selector switch, (0-500 V) Voltmeter with selector switch, phase indication light with protection fuse, on / off / trip indicating light with protection fuse. SET 01OUTGOINGSi) For 4 Nos. Fan Motor of 15 KW40 / 63 A TPN MCB 16 / 25 A Star Delta Starter, overload relay, start / stop push buttons, ammeter (0-40 / 60A) with three CT, on/off/trip indication lights with protection fuse, single phase preventer & auto / manual mode selector switch. SET 02Controls & interlocking accessories as required. LOT Isolator Switch With Metal Enclosure For ODU (IP-65) |
| 417 | 32 / 40 A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site condition.Power & Control CablingSupply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification.For Motor of 7.5 to 11.3 Kw 2 x 3C x 6 Sq. mm (Rate for Single Run) |
| 418 | 32 / 40 A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site condition.Power & Control CablingSupply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification.For Motor of 15.0 Kw 2 x 3C x 16 Sq. mm |
| 419 | 32 / 40 A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site condition.Power & Control CablingSupply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification.For VRV ODU Unit (From AC Panel to Isolators near ODU)1 x 3C x 16 Sq. mm |
| 420 | 32 / 40 A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site condition.Power & Control CablingSupply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification.For VRV ODU Unit (From AC Panel to Isolators near ODU)1 x 3C x 25 Sq. mm |
| 421 | 32 / 40 A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site condition.Power & Control CablingSupply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification.For VRV Outdoor / HW ODU (From Isolators to Unit)1 x 3 C x 4.0 Sq. mm Copper Flexible Cable |
| 422 | 32 / 40 A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site condition.Power & Control CablingSupply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification.For VRV Outdoor / HW ODU (From Isolators to Unit)1 x 3 C x 6.0 Sq. mm Copper Flexible Cable |
| 423 | 32 / 40 A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site condition.Power & Control CablingSupply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification.For VRV Outdoor / HW ODU (From Isolators to Unit)1 x 3 C x 10.0 Sq. mm Copper Flexible Cable |
| 424 | Control cabling (PVC insulated Copper conductor of 1.1 KV Grade armoured cable) 3C x 1.5 Sq. mm |
| 425 | Control cabling (PVC insulated Copper conductor of 1.1 KV Grade armoured cable) 4C x 1.5 Sq. mm |
| 426 | Transmission & Control Wiring For VRV SystemProviding & fixing of control cum trans-mission wiring of copper between indoor and out door unit in 25 mm PVC Conduit.3C / 2C x 1.5 Sq mm |
| 427 | Earthing Strip / Wires as per specs.Supply & laying of 8 SWG GI wire or in recess for loop earthing as required. |
| 428 | Supply & laying of 6 SWG GI wire or in recess for loop earthing as required. |
| 429 | Supply & laying of Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006. |
| 430 | Cable TraySupplying and installing following size of perforated GI cable trays including bends. tee, reducers etc with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with GI suspenders including bolts & nuts, suspenders etc as required.100 mm wide x 50 mm depth x 1.6 mm thickness. |
| 431 | Cable TraySupplying and installing following size of perforated GI cable trays including bends. tee, reducers etc with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with GI suspenders including bolts & nuts, suspenders etc as required.150 mm wide x 50 mm depth x 1.6 mm thickness. |
| 432 | Cable TraySupplying and installing following size of perforated GI cable trays including bends. tee, reducers etc with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with GI suspenders including bolts & nuts, suspenders etc as required.300 mm wide x 50 mm depth x 1.6 mm thickness. |
| 433 | Hi-wall Split Unit (5 Star Rated) For Various Areas Supply, installation, testing and commissioning of Hi-wall Split Unit with rotary compressor & cordless control of following capacity with outdoor unit stand, power & control cabling, MCB etc. as required.2.0 TR |
| 434 | Refrigerant Piping Supply, installation, testing and commissioning of additional refrigerant piping (two lengths) duly insulated with 25 mm for indoor application and 38 mm for outdoor application for Precision AC & 19 mm for indoor application and 19 mm for outdoor for Split AC, with UV coating closed cell nitrile rubber of density 60+/-10% Kg/m3 to interconnect indoor & outdoor units for each circuit. (Refrigerant piping for individual circuit shall be restricted to maximum length of 25 Meter by AC Contractor) For Hi-wall Split Units Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysNov 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender