Tender For Special Repair Of Building No P-13 Or Md Accn In Sect ‘A At Dinjan Mil Stn
Tender Value
42.70 Lakhs
Estimated cost
Bid Submission
31 Oct 2026
2 days left
EMD
87400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tinsukia → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair Of Building No P-13 Or Md Accn In Sect ‘A At Dinjan Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | B/R WORKS :Demolition of cement concrete in ground floor n exc 15 cm thick (un reinforced) complete all as specified and directed. |
| 2 | M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in chajjas top, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over top of chajja incl mixed with WPC as per manufacturers instructions complete all as specified and directed. |
| 3 | Dismantling of plain or corrugated sheeting incl wind tiecomplete all as specified and directed. |
| 4 | S & F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 5 | S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 6 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and directed. |
| 7 | S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing three coats of white wash complete all as specified and as directed. |
| 8 | M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 9 | Taking down chowkats or frame, n. exc 1.5 sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed. |
| 10 | Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exe 1.50 & n.exc. 4 sqm in each complete all as specified & directed. |
| 11 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 12 | S&F solid PVC moulded door frame of size 50mmx47mm made out of 5mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast complete all as specified and directed. |
| 13 | S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site complete all as specified and directed. |
| 14 | S&F 75 mm size stainless steel butt hinges medium weight cold rolled complete all as specified and directed. |
| 15 | Supply and fix 150mm long aluminium handles, cast type, anodised complete all as specified and as directed. |
| 16 | Supply and fix 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed. |
| 17 | M & L MS flat iron work as in hold fast and similar small articles, cut to length, bent to shape, drilled hole and fixed with screw etc conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 18 | S & F pressed steel frames for door 105mm X 60mm with revates including necessary fittings lugs, hings, lock strike plate, etc supplied and fixed complete all as specified and directed.(PCC filling in holllow section shall be measured and paid for separately.) |
| 19 | S&F pressed steell door frame 125x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates complete as specified and directed (PCC filling in holllow section shall be measured and paid for separately.) |
| 20 | M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165 complete all as specified and directed. |
| 21 | S&F 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 22 | S & F 35mm thick, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and directed. |
| 23 | Supply and fix butt hinges 100mm long cold rolled medium weight complete all as specified and as directed. |
| 24 | Supply and fix for 150mm long aluminium handles, cast type, anodised complete all as specified and as directed. |
| 25 | Supply and fix 150mm long mild steel pressed handles, oval type, stove enameled black complete all as specified and as directed. |
| 26 | S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long complete all as specified and directed.. |
| 27 | Supply and fix 250mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed. |
| 28 | S&F in repair Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 29 | S&F door seal aluminium rod withnylon brush of approved colour fixed to shutter with and incl 20mm steel wooden screw complete all as specified and directed. |
| 30 | M & L preparation of new untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 31 | S & F in repairs curtain rails, harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed. |
| 32 | S&F powder coated aluminium anodised frame for doors, windows etc with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 33 | S&F Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including all necessary fittings like hinges joining cleats, glazing clips,moving roller, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. |
| 34 | Supply and fixing of aluminium sliding window with powder coating (minium thickness of powder coating 50 micron) including following components / specification complete all as specified and directed. (i) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (ii) All vercal/ horizontal joint shall be of extruded aluminium section so as to avoid any play between jointed members. (iii) all other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, srews, etc. (iv) Stainless steel wire cloth, 036 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples, etc. (v) Sheet glass 4 mm thick selected quality tinted/black glass and glazing with oil putty or fixed with wooden beads in square not exceeding 0.5 Sqm in each pane (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5, 5R/5. Note :- Grill shall be measured and paid separately. |
| 35 | Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement : 2 Coarse sand) to match the existing floors drilling and plugging holes etc complete all as specified and as directed. |
| 36 | M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 37 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove, dust etc. and applying neat cement slurry @ 3Kg/Sqm complete all as specified and directed. |
| 38 | Demolition of stone slabs or tiles of any description or thickness as in floors, pavings, aprons, pathway etc laid dry or laid dry and pointed complete all as specified and directed. |
| 39 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed. |
| 40 | M & L 25 mm thick PCC type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in leveling layer complete all as specified and directed. |
| 41 | M&L for ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed or bedding layer of cement morter (1:4) for laying of floor finishes complete all as specified and directed. |
| 42 | M&L for ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed. |
| 43 | M&L Non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm 7mm thick coloured tiles in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and incl screed bedding 15mm thick in CM 1:4 as specified and as directed. |
| 44 | M&L for glazed ceramic coloured tiles in vertical surface 300x450x7mm thick in dado over and incl 10mm thick screed bed in CM 1:4 on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and directed. |
| 45 | M & L 75 mm thick PCC type D-2 1:4:8 ( using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed. |
| 46 | M&L Laquer coated Chequered cement concrete coloured tiles 30cmx 30cmx25mm thick set jointed in neat cement slurry and pointed in grey cement mixed with pigment to match the shade of tiles over and incl 15 mm thck cement screed in CM 1:4 complete all as specified and directed. |
| 47 | M&L Pre-cast (Factory casted) cement concrete Kerb stone casted in PCC (1:2:4) Type B-1 using 20mm graded stone aggregates with plan or interlocking joints (as directed) with solid blocks, exc. 10 cm in width and setting and jointed in cement mortar 1:6, complete all as specified & directed. |
| 48 | M & L for preparation of kerb stone, new un-treated concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint in black and white colour over a coat of primer complete all as specified and directed. |
| 49 | Material and labour for Machine cut kota stone slab flooring 20 to 25mm thick size not less than 22\\" x 22\\" laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick cement screed bed in cement mortar 1:3 including rubbing and mirror polishing complete all as specified and as directed. |
| 50 | Material and labour for kota stone slab 20 to 25mm thick in riser of steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick rendering in cement mortar 1:4 including cutting, moulding outer edges, rubbing and mirror polishing complete all as specified and as directed. |
| 51 | Demolition of Brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc,excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 52 | Material & Labour for Brick work with sub class ‘B’ old size bricks wel burnt straight or curved on plan exc 6m mean radius built in CM(1:6) complete all as specified and directed. |
| 53 | M&L for half thick brick work with sub class \\"B\\" bricks well burnt straight or curved on plan exceeding 6m mean radius with old size bricks locaaly available built in cement mortar 1:4 complete all as specified and directed. |
| 54 | Taking down cement plaster on brick walls/ concrete surface, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 55 | M&L 15 mm thick cement plaster on wall in CM (1:6) on fair faces of brick work incl finished even and smooth without using extra cement complete all as specified and directed. |
| 56 | M&L for rendering 15 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement Mortar in 1:4 using water proofing compound in top layer (Water Proofing Compound measured separately) and finished even and smooth (without using extra lime or cement) complete all as specified and directed. |
| 57 | M&L 5 mm thick cement plaster in CM (1:3) on ceiling surfaces incl finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 58 | M&L for applyiing 15mm plaster with polymer modified mortar fortified with SBR(Nito Bond SBR 45) in proportion 1:3 by weight 5 litr Nitobond SBR 45 added to 50kg cement with 13 litr water and finished surfaces to existing adjoining surface of ceiling, columns, beam and like etc complete all as specified and directed |
| 59 | Supply only Integral water proofing compound complete all as specified and directed. |
| 60 | M&L for complete removal of exisiting treatment of wall and applying two coat of oil bound distemper over 3 mm thick wall care putty to make the surface evenn annd smooth complete all as specified and directed. |
| 61 | M&L for preparation of newly plastered surfaces of walls & applying two coat of distemper oil emulsion over 3 mm thick wall care putty to make the surface even and smooth over one coat of chalk whiting priming paint complete all as specified and directed. |
| 62 | M&L for preparation of new plastered surface of wall Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including 3 mm thick plaster of paris putty on new surfaces to make the surface evenn and smooth complete all as specified and directed. |
| 63 | M&L for complete removal of existing treatment inclpreparation of old surfaces, scrubing down, washing etc from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7\\"/9\\" to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfacesincl 1mm thick plaster of paris putty, using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and will execute the same work by authorised applicator as mentioned in PS and acessories complete all as specified and directed. |
| 64 | M&L preapring old plastered surfaces incl washing rubbing down and stopping of distempered and painted surface of ceiling and applying two coat of white wash complete all as specified and directed. |
| 65 | M&L for Preparation of new plastered surfaces and applying three coat of white wash on ceiling complete all as specified and directed. |
| 66 | M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation complete all as specified and directed. |
| 67 | M&L cement concrete 75mm thick 1:2:4 type B-2 using 40mm graded stone aggregate as in pathways/hardstanding laid in alternate ways, each panel not exceeding 3.00 Sqm finished the surface even and fair without using extra cement and joint to be filled with Bituminous mastic filling in proportion of Bitumen and sand (1:2) including necessary form work complete all as specified and directed. |
| 68 | M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound, Grade ‘A’ complete all as specified and directed. |
| 69 | Material and labour rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening etc. confirming to Fe 410-W (gde-E-250) quality-A and fixing complete all as specified and as directed. |
| 70 | Supply and fix rolled mild steel as in joist, channel, angle or tee section/hold fast/wind ties fixed independently with connecting base plate etc complete all as specified and as directed. |
| 71 | M&L PCC 1:3:6, C-1 (using 20 mm graded stone aggregate) as in bed blocks for inserting holdfast/ filling of steel frame, etc including necessary form work complete as specified and directed. |
| 72 | Taking up or down 15mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed. |
| 73 | Taking up or down 20mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified and directed. |
| 74 | Refixing 15mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.) complete all as specified and directed. |
| 75 | S & F steel tubing 15mm bore medium grade galvanised with all fittings and fixed complete to wall, ceilings or laid in floors complete all as specified and directed. |
| 76 | Refixing 20mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.) complete all as specified and directed. |
| 77 | S & F steel tubing 20 mm bore medium grade galvanised with all fittings and fixed complete to wall, ceilings or laid in floors complete all as specified and directed. |
| 78 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as specified and directed. |
| 79 | S&F in repairs for MS grating CP 75/100mm dia, without hole and with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as specified and directed. |
| 80 | S&F in repairs Mirror cabinet PVC frame of size 400 x 500 mm fixed to wall with rawl plug & stainless steel suitable size screws complete all as specified and direceted.Make : Prayag cat No 554 or equivalent as approved by GE. |
| 81 | S & F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 82 | S&F 15mm bore wall mixer with L bend with provision for over head shower complete all as specified and as directed |
| 83 | S&F 15 mm bore wall mounted sink mixer regular spout with long neck as per model Casa Cat Part No 9216 of make prayag or equivalent complete all as specified and as directed |
| 84 | S & F in repairs 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 85 | S & F in repairs, stop valves, 15 mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 86 | S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed. |
| 87 | S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed. |
| 88 | S& F as repairs brass chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union 125 mm size complete all as specified and directed. |
| 89 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 90 | S&F in repairs stainless steel peg set of 6 peg, 45 cm long, complete all as specified and directed. |
| 91 | S&F in repair soap dish of stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed |
| 92 | S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash hand basin 32/40mm dia, length not less than 70 cm, connected to PVC waste coupling/fittings complete all as specified and as directed. |
| 93 | S & F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed. |
| 94 | S & F in repairs Vitreous china wash basin, white,Corner, size (410 x 410 x 200mm) with brackets,excluding pillar cock 15 mm bore CP, PVC connection of 450 mm long including PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and directed. |
| 95 | S & F 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 96 | S & F vitreous china pedestal pattern white connection to trap 'P' or 'S' and flush pipe etc including seat cover and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing including taking down the existing old one complete all as specified and directed. |
| 97 | S&F in repairs plastic water closet seat cover white closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified an directed. |
| 98 | S & F in repairs mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 99 | Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete as specified in SSR Part-I complete all as specified and directed. |
| 100 | S & F in repairs, 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum 210 gms) complete all as specified and directed. |
| 101 | S&F as in repairs for Gun metal gate valves with iron wheel headscrewed both ends for iron pipes or for unions for 20 mm bore pipes, complete all as specified and directed. |
| 102 | S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 103 | S&F 0.71 mm thick Plain Aluminium sheeting alloy 31000H4 in ridges, hip, valley gutter, crumple joint etc. complete all as specified and directed. |
| 104 | S&F wall mounted Modern kitchen Utensils Dish Rack Stainless steel (31X10X30 inches) complete all as specified and directed. |
| 105 | M& L for PVC (SWR) floor trap 100 mm dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed. |
| 106 | M& L for PVC (SWR) floor trap 75 mm dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed. |
| 107 | M&L for water proofing treatment on RCC roof etc. comprising with the following operation complete all as specified and directed. below:- (a)Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. (b) M&L 25 thick cement concrete type B0 1:2:4 (12.5 mm graded aggregate) finished even and smooth. (c) Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight). (d) M&L for 20 mm thick screed bed in cement mortar 1:4 finished even and smooth.(e) Preparing & cleaning of fully dried cement plastered surface. (f) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming IS-3384. (g) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (h) One coat of aluminium paint over APP membrane @0.11Kg/Sqm.Note:- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab. |
| 108 | M&L for special treatment for sunken portion of WCs/Bath & toilet executed in following stage complete all as specified and directed.:- Stage1:- Demolition of wc including lime concrete and cemennt concrete etc and preparing of surfaces of existing sunken portion of wc`s or bath etc with wire brush to removed all loose dirts, oil grease etc including removing debries from site of work etc. Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per manufacturere`s instructions. Stage 3:- Apply Dr. Fixit Premeseal primer or equivelent of STP Ltd (and allow to dry for 8 hrs) all as per manufacturer`s instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 micron or shilicry 215 of STP (The surfaces after painting one coats shall be allowed to dry for 6 hrs before next coats) Stage 5:- Rendering 10mm thick in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per manufacturere`s instructions. Stage 6:- All CI joints shall be filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr. Fixit pidicrete URP all as per manufacturer`s instructions. Stage 7:- Making holes in walls and fixing 600mm long 40mm dia medium grade GI spouts for draining of excess water if any. Stage 8:- Carryout ponding testfor 48 hrs to ensure water tighteness of repaired sunken portion and filling of sunken portion for cement concrete Type E2, 1:5:10 using 40mm graded stone aggregate as in lean concrete complete all as specified and directed. Note:- only plan area shall be measured for payment under this items. (b) Depth of suken portion of WC`s/ bath shall be upto 35 CM which is to be taken into account while coating the rate against this item. (c) The rate shall be quoted by contractor shall be deemed to be included for all the horizontal and verticl treated surface of sunken portion of WC`s/baths. |
| 109 | M&L for 20mm thick granite (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform, and like in cement mortar (1:4) over and incl 15mm thick including pointing in white cement (1:2) using marble dust with admixure of pigment to match the shade of granite screed layer in CM 1:3 complete all as specified and directed. |
| 110 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 111 | M&L for cutting holes in stone /RCC/granite slab for inserting coocking gas cylinder pipe and making good complete all as specified and directed. |
| 112 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 113 | Material and labour for RCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in slab supported on walls, beams and column in floors, roof landings, balconies, canopies, deck slabs and in shelves complete all as specified and as directed. (Note : Reinforcement shall be measured and paid seperately under relevant) |
| 114 | Material and labour TMT bar 10 mm and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and as directed. |
| 115 | M&L formwork to soffits of suspended slabs such as roof slab, floor slabs, landing covers, and similar works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed. |
| 116 | M&L of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. |
| 117 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed. |
| 118 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 119 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shelves of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel L Shaped brackets which should with hold as average weight of 20-30 kg and fixed with ecessary fully body threaded star headed counter sunk S.S screw, complete all as specified and directed. |
| 120 | S & F stainless steel soft close hydraulic clip concealed cabinet hinges fixed with stainless steel screws complete all as specified and directed. |
| 121 | S & F Width of flaps (when open) 40mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 122 | S & F 75 mm size aluminium anodised Hasp and staple, safety type with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed. |
| 123 | S & F 50mm dia polished hard wood knobs fixed with thread screw and nut complete all as specified and directed. |
| 124 | S & F stainless steel magnetic door catched magnet of size 50 X 15mm fixed with stainless steel screw on shelf/sides wall and shutter complete all as specified and as directed |
| 125 | Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding, complete all as specified and directed. |
| 126 | S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified and directed. |
| 127 | M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe complete all as specified and directed. |
| 128 | M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe complete all as specified and directed. |
| 129 | S&F for 50mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 5 ton/Sqm in square, rectangular shape of size 600X600 complete all as specified and directed. |
| 130 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. |
| 131 | S & F Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges of thickness 1.25mm of dia 150mm complete all as specified and directed. |
| 132 | S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling of PCC & taking out old unserviceable 110mm bore PVC pipe with fittings & making good disturbed area complete all as specified and directed. |
| 133 | S &F for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, 110mm bore pipes complete all as specified and directed. |
| 134 | S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 75mm bore pipes complete all as specified and directed. |
| 135 | S & F for PVC (SWR) bends any radius with access door, 110mm bore complete all as specified and directed. |
| 136 | S & F for PVC (SWR) bends any radius, 110mm bore complete all as specified and directed. |
| 137 | S & F for PVC (SWR) vent cowl, 75mm bore complete all as specified and directed. |
| 138 | S & F for PVC (SWR) bends any radius, 75mm bore complete all as specified and directed. |
| 139 | S & F for PVC (SWR) bends any radius with access door, 75mm bore complete all as specified and directed. |
| 140 | S&F PVC(SWR) Vent cowl 75mm dia complete all as specified and directed. |
| 141 | S&F PVC(SWR) Vent cowl 110mm dia complete all as specified and directed. |
| 142 | S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 143 | E/M WORKS :Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed. |
| 144 | Taking down carefully MCB DBs any type and size by unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes complete all as specified and directed. |
| 145 | Taking down fan, sealing cable end, dismantling blades and removing fan and keeping it in MES store for safe custody and refix it after repair complete all as specified and directed. Please Enable Macros to View BoQ information |
| 146 | Taking down fan, sealing cable end, dismantling blades and removing fan and keeping it in MES store for safe custody and refix it after repair complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysNov 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender