Supply Of FERRITIC STEEL

Sharing tender

Supply Of ferritic steel , ferritic steel sheet 5x1250 x 3000 mm., as per drawing: rdso spec no.c-k201, gr ade x2crni12 (409m) table 1&2. heat treatment condition 2d as per table-5., packing instruc tion: stainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic st eel) coils. the coil shall be protected in reasonably good condition to withstand nor mal handling hazard during transit with the following provision as the barest minimu m: i) coil should be wrapped with a layer of water proof paper through out whole leng th. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil should be wrapped with gi sheet. iv) side of the coil should be covered with card b oard sheet. v) after this whole coil should be wrapped with biodegradeable plastic sh eet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring f ollowed by another iron ring. vii) outer edge of the coil should be wrapped with gi rin g. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil shoul d be mounted on wooden blocks for easy lifting/stacking. x) the sheets in coil form fo r thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 100 0-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2 mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 tonnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheet s/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate s hall be seprated with a layer of water proof paper, after this the whole bundle shoul d be wrapped with double layer of water proof paper and a biodegradeable plastic she et of suitable thickness. a metal protection in edges should also be provided. ii) all bu ndles shall have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling. mechanical damange & corrosion during transit if any shall be at the cost of supplier. [ warranty period: 30 months after the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ] ] , ferritic steel sheet 3x1250x3100 mm., as per drawing: rdso spec. no. c-k201, gr ade x2crni12 (409m) table 1&2, heat treatment condition 2b as per table-5., packing instruc tion: stainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic st eel) coils. the coil shall be protected in reasonably good condition to withstand nor mal handling hazard during transit with the following provision as the barest minimu m: i) coil should be wrapped with a layer of water proof paper through out whole leng th. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil should be wrapped with gi sheet. iv) side of the coil should be covered with card b oard sheet. v) after this whole coil should be wrapped with biodegradeable plastic sh eet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring f ollowed by another iron ring. vii) outer edge of the coil should be wrapped with gi rin g. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil shoul d be mounted on wooden blocks for easy lifting/stacking. x) the sheets in coil form fo r thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 100 0-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2 mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 tonnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheet s/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate s hall be seprated with a layer of water proof paper, after this the whole bundle shoul d be wrapped with double layer of water proof paper and a biodegradeable plastic she et of suitable thickness. a metal protection in edges should also be provided. ii) all bu ndles shall have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling. mechanical damange & corrosion during transit if any shall be at the cost of supplier. [ warranty period: 30 months after the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ] ] , ferritic steel sheet 4x1250x3100 mm., as per drawing: rdso spec. no. c-k201, gr ade x2crni12 (409m) table 1&2, heat treatment condition 2b as per table-5., packing instruc tion: stainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic st eel) coils. the coil shall be protected in reasonably good condition to withstand nor mal handling hazard during transit with the following provision as the barest minimu m: i) coil should be wrapped with a layer of water proof paper through out whole leng th. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil should be wrapped with gi sheet. iv) side of the coil should be covered with card b oard sheet. v) after this whole coil should be wrapped with biodegradeable plastic sh eet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring f ollowed by another iron ring. vii) outer edge of the coil should be wrapped with gi rin g. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil shoul d be mounted on wooden blocks for easy lifting/stacking. x) the sheets in coil form fo r thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 100 0-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2 mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 tonnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheet s/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate s hall be seprated with a layer of water proof paper, after this the whole bundle shoul d be wrapped with double layer of water proof paper and a biodegradeable plastic she et of suitable thickness. a metal protection in edges should also be provided. ii) all bu ndles shall have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling. mechanical damange & corrosion during transit if any shall be at the cost of supplier. [ warranty period: 30 months after the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ] ] , ferritic steel coil 2x1250mm., as per drawing: rdso spec. no. c-k201, grade x2c rni12 (409m) table 1&2, heat treatment condition 2b as per table-5., packing instruction: st ainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic steel) c oils. the coil shall be protected in reasonably good condition to withstand normal ha ndling hazard during transit with the following provision as the barest minimum: i) coi l should be wrapped with a layer of water proof paper through out whole length. ii) c oil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil s hould be wrapped with gi sheet. iv) side of the coil should be covered with card board sheet. v) after this whole coil should be wrapped with biodegradeable plastic sheet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring follow ed by another iron ring. vii) outer edge of the coil should be wrapped with gi ring. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coi l and minium 3 steel bands on the circumference of the eye. ix) whole coil should be mo unted on wooden blocks for easy lifting/stacking. x) the sheets in coil form for thickn ess 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 1000-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 to nnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheets/plates s hall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate shall be se prated with a layer of water proof paper, after this the whole bundle should be wrapp ed with double layer of water proof paper and a biodegradeable plastic sheet of suita ble thickness. a metal protection in edges should also be provided. ii) all bundles shal l have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every addi tional meter. the bundles shall also be provided with skid (wooden packing under neat h) to facilitate handling. mechanical damange & corrosion during transit if any shall b e at the cost of supplier. , proction procedure: covered in pi [ warranty period: 30 months aft er the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ] ] , ferritic steel sheet 2x1250x2100mm., as per drawing: rdso spec. no. c-k201, gr ade x2crni12 (409m) table 1&2, heat treatment condition 2b as per table-5., packing instruc tion: stainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic st eel) coils. the coil shall be protected in reasonably good condition to withstand nor mal handling hazard during transit with the following provision as the barest minimu m: i) coil should be wrapped with a layer of water proof paper through out whole leng th. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil should be wrapped with gi sheet. iv) side of the coil should be covered with card b oard sheet. v) after this whole coil should be wrapped with biodegradeable plastic sh eet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring f ollowed by another iron ring. vii) outer edge of the coil should be wrapped with gi rin g. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil shoul d be mounted on wooden blocks for easy lifting/stacking. x) the sheets in coil form fo r thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 100 0-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2 mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 tonnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheet s/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate s hall be seprated with a layer of water proof paper, after this the whole bundle shoul d be wrapped with double layer of water proof paper and a biodegradeable plastic she et of suitable thickness. a metal protection in edges should also be provided. ii) all bu ndles shall have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling. mechanical damange & corrosion during transit if any shall be at the cost of supplier. , proction procedure: covered in pi [ warranty period: 3 0 months after the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ] ] , ferritic steel coil 2.5x1250mm., as per drawing: rdso spec. no. c-k201, grade x 2crni12 (409m) table 1&2, heat treatment condition 2b as per table-5., packing instruction: stainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic steel) coils. the coil shall be protected in reasonably good condition to withstand normal h andling hazard during transit with the following provision as the barest minimum: i) c oil should be wrapped with a layer of water proof paper through out whole length. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil s hould be wrapped with gi sheet. iv) side of the coil should be covered with card board sheet. v) after this whole coil should be wrapped with biodegradeable plastic sheet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring follow ed by another iron ring. vii) outer edge of the coil should be wrapped with gi ring. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coi l and minium 3 steel bands on the circumference of the eye. ix) whole coil should be mo unted on wooden blocks for easy lifting/stacking. x) the sheets in coil form for thickn ess 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 1000-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 to nnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheets/plates s hall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate shall be se prated with a layer of water proof paper, after this the whole bundle should be wrapp ed with double layer of water proof paper and a biodegradeable plastic sheet of suita ble thickness. a metal protection in edges should also be provided. ii) all bundles shal l have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every addi tional meter. the bundles shall also be provided with skid (wooden packing under neat h) to facilitate handling. mechanical damange & corrosion during transit if any shall b e at the cost of supplier. , proction procedure: covered in pi [ warranty period: 30 months aft er the date of delivery ] [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ] ]