Tender For Maintenance Of Khowai Communication Office Building By Providing Plastering Doors, Windows Ceiling, Pre-Painted Galvalume Sheets Roofing Etc. Including Painting Inside And Out Side, At The Premises Of Khowai Police Commn. Station Under Sp(
Tender Value
5.29 Lakhs
Estimated cost
Bid Submission
29 Oct 2026
15 days left
EMD
10593
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Khowai → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Maintenance Of Khowai Communication Office Building By Providing Plastering Doors, Windows Ceiling, Pre-Painted Galvalume Sheets Roofing Etc. Including Painting Inside And Out Side, At The Premises Of Khowai Police Commn. Station Under Sp(Commn.)Agartala
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling doors, windows and clerestory windows(Steel or wood)shutter including chowkhats, architrave, holdfasts etc, complete and staking within 50 meters lead |
| 2 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc. complete as per direction of the Engineer-in- charge |
| 3 | Dismantling GS sheet roofing including ridges hips, valleys, gutters wind ties etc. including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50m etc. complete as per direction of the Engineer-in-charge |
| 4 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: (1) of area 3 sqm and below |
| 5 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : (i) Local Teak wood |
| 6 | Providing and fixing paneled/ or paneled and glazed shutters for doors, windows and clerestory windows including ISI marked bright finished/black enameled M.S butthinges with necessary screws excluding paneling and or glazing, which will be paid for separately but including the wooden beading of 20 x 12 mm for fixing paneling and or glazing as per direction of Engineer-in-Charge (a)Local Teak wood (i) 35 mm thick shutters |
| 7 | Providing 40 X5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 x10x 15 cm 1:3:6 mix (1 cement :3 fine sand:6 graded stone aggregate 20mm nominal size) |
| 8 | Providing and fixing panelling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows(area of opening for panel inserts excluding portion inside grooves or rebates to be measured) Panclling for paneled or paneled and glazed shutters 25 to 40 mm thick(i)Local Teak wood 16mm thick |
| 9 | Providing and applying cement slurry on old CC/RCC/Brick works in joints to receive new fresh CC/RCC/brick works including roughening and cleaning the old surface as required complete as per direction of the Engineer in charge |
| 10 | Supply & installation of pre-painted Galvalume sheets for roofing /eladding (size,shape)and pich of corrugation as approved by Engineer –in charge ) in 550mpa steel grade made out of cold rolled steel coated with zinc-Aluminiium alloy coating of 43.5% Zn 55% AI and 1.5% silicon confrming to ASTM A792/A792M and ASI 1397. Alloy coating AZ150/AZ70.colour coated with high quality polyester coating top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 micron minimum to avoid scratches while transpiortation and should be supplied in single length upto 12 metre or as desired by Enginner-in-charge.The sheet shall be fixed using self drilling /self tapping screws of size (5.5x55mn) with EPDM washers filled with white lead complete upto any pitch in horizontal /vertical or curved surfaces excluding the cost of purline ,rafters and trusses and including cutting to size and shape wherever required and as per direction of Enfineer-in-charhge (i)0.50mm thickness |
| 11 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade made out of cold rolled steel coated with Zinc Aluminium alloy coating of 43.5% Zn, 55% A I and 1.5 silicon confrming to AASTM A792/A792M and ASI 1397.Alloy coating AZ150/AZ70.colour coated with high quality polyester coating top coated of modified polyester of 20 micron, back side coat of 5 micron having epoxy primer coat of 5 micron on both side etc. complete as per d as direction of Enginner-in-charge.Sheet should have protective guard film of 25 microns minimum to avoid scratches while transpiortation, Sheet should have protective guard film of 25bmicrons minimum to avoid scratches while transportation .The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Vally /Gutter/Flashing of width 610mm (a)0.40mm thickness |
| 12 | Providing and fixing factory made UPVC door frame made of UPVC extruded, section having an overall dimiension, as below (tolerance +/- 1 mm) with wall thickness2.0mm+/- 02 mm corners of the door frame to be jointed with Galvanized brackets and stainless screws , joint mitred and plastic wilded .The hinge side vertical of the frames reinforced by Galvanized MS tube of size 19X 19 mm and 1 mm+/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specificiation and direction of Engineer –in-Charge (i) Extruded section profile size 48 X 40mm |
| 13 | Providing and fixing on wall face unplasticised-PVC mouldedfiting /accessories for unplasticisedReigied PVC soil wast& waste & vent pipes conforming to IS; 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion (a) Coupler (i) 110 mm |
| 14 | Bend 87,5(i)110 mm |
| 15 | Single equal tee without door Ii)110 x 110 x 110 mm |
| 16 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering –All work upto plinth level: (i)1:2;4 ( 1 cement ; 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 17 | 12 mm cement plaster of mix (i) cement morter 1:4(1 cement : 4 fine sand) |
| 18 | Providing and fixing Ist class quality ceramic glazed wall tiles conforming to IS : 15622-2017 (thickness to be specified by the manufacturer) of approved make in all colour ,shades of any size as approved by Engineer-in-Charge in skirting ,risers of steps and dqdos laid over 12 mm thick bed of cement mortar 1:3(1 cement ;3 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc.all complete as per direction of the Engineer-in-charge (i) 450 mm x 300 mm in all shades and desing |
| 19 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 – 2017 of approved make in colours such as white, lvory,Grey, fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand) Jointing with grey cement slurry @ 3.3 kg.sqm including pointing the joints with white cement and matching pigment etc, all complete as per direction of the Engineer in – charge . (a) mat Finish Tiles/Anti-skid Tiles/ Glossy Tiles (i)300 mm x 300 mm in all shades and designs |
| 20 | Providing and fixing on well faceunplasticised Rigid PVC soil, waste & vent pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion : Single socketed pipe – 110 mm OD |
| 21 | Providing and fixing white vitreous china pedestal type water closet(European type W.C pan) with seat and lid, 10 litre low level white P.V.C flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 22 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work – Exposed on wall (a) 15 mm nominal outer dia. Pipes |
| 23 | 25 mm nominal outer dia.Pipe |
| 24 | Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position : Local Teak wood |
| 25 | Providing and fitting fixing medium density Fiber hard board sheet ceiling with wooden beading , nails etc. complete as per direction of Engineer – in- Charge. ( wooden beading will be paid separately ). A). 6mm thick sheet |
| 26 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat in unexposed surface etc. complete : (a). local teak wood (i) 50 x 12 mm |
| 27 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part – I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 28 | 24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59 x 24 mm and wall thickness 2 mm +02 mm with inbuilt edging on both sides, The styles and rails mired and joined at the corners by means of M.S. galvanized /plastic brackets of size 75 x 220 mm having wall thickness 1,o, mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanized MS tube of Size 20 x 20 mm and 1 mm _ 0.1 mm wall thickness. The lock rail made up to “H: Sectuion ,a UPVC hollow section of size 100 nx 24 mm and 2mm + 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galuvanised MS “U” cleats The shutter frame filled with a UPVC multi –chambered single panel of size not less than 620 mm. having overall thickness of 20 mm and 1 mm + 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanized MS rod and fastened with nuts and washers, complete as per manufactures specificication and direction of Engineer-in-charge (for W,C.and Bathroom door shutter) |
| 29 | Providing & fitting fixing of C.P brass hand spray (Royal made) as per direction of the Engg. In charge |
| 30 | Providing & fitting fixing of C.P. brass Twin one stop cock (Royal made) complete as per direction of the Engg. In charge |
| 31 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: (i) 15 mm nominal bore |
| 32 | Cutting holes upto 30x30 cm in walls including making good the same : (i) With 1st class bricks |
| 33 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 34 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test certificate issued by the Manufacture ] : New work (two or more coats) over and including water thinkable priming coat with cement primer |
| 35 | Distempering with 1st quality washable acrylic distemper of approved brand and manufacture and of required shade on old work (one or more coats), to give an even shade as required complete as per direction of the Engineer in charge |
| 36 | Painting with synthetic enamel paint (one or more coats ) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge |
| 37 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [payment shall be made after submission of Test Certificate issued by the Manufacture ] : Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 38 | Finishing walls with premium acrylie smooth exteriox paint with silicon additives of required shade of approved brand and manufacture (Payment shall be made after submission of Test Certificate issued by the manufacture ) New work (Two or more coats applied @ 1.43 litre/10 sqm over and including priming coat a exterior primer applied @ 2.20 Kg./10 sqm) |
| 39 | Providing and fixing aluminium sliding door bolts ISI marked anodized coating not less than grade Ac 10 as per Is: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250 X16 mm |
| 40 | Providing &fitting aluminium tower bolts ISI marked handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 18680 transparent or dyed to required colour or shade with necessary screws etc. complete : (i)150 x 10 mm |
| 41 | Providing & fitting fixing aluminium handles ISI marked anodized ( anodic coating not less than grade AC 10 as per IS: 1868) transparment or dyed to required colour or shade with necessary screws etc .Complete : 125 mm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysOct 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender